Abstract: In this study, we demonstrate a high-resolution
refractive index sensor based on a Magnetic Photonic Crystal (MPC)
composed of a triangular lattice array of air holes embedded in Si
matrix. A microcavity is created by changing the radius of an air hole
in the middle of the photonic crystal. The cavity filled with gyrotropic
materials can serve as a refractive index sensor. The shift of the
resonant frequency of the sensor is obtained numerically using finite
difference time domain method under different ambient conditions
having refractive index from n = 1.0 to n = 1.1. The numerical results
show that a tiny change in refractive index of Δn = 0.0001 is
distinguishable. In addition, the spectral response of the MPC sensor is
studied while an external magnetic field is present. The results show
that the MPC sensor exhibits a dramatic improvement in resolution.
Abstract: We report the design and characterization of ultra high
quality factor filter based on one-dimensional photonic-crystal Thue-
Morse sequence structure. The behavior of aperiodic array of
photonic crystal structure is numerically investigated and we show
that by changing the angle of incident wave, desired wavelengths
could be tuned and a tunable filter is realized. Also it is shown that
high quality factor filter be achieved in the telecommunication
window around 1550 nm, with a device based on Thue-Morse
structure. Simulation results show that the proposed structure has a
quality factor more than 100000 and it is suitable for DWDM
communication applications.
Abstract: Multiple-input multiple-output (MIMO) radar has
received increasing attention in recent years. MIMO radar has many
advantages over conventional phased array radar such as target
detection,resolution enhancement, and interference suppression. In
this paper, the results are presented from a simulation study of MIMO
uniformly-spaced linear array (ULA) antennas. The performance is
investigated under varied parameters, including varied array size,
pseudo random (PN) sequence length, number of snapshots, and
signal to noise ratio (SNR). The results of MIMO are compared to a
traditional array antenna.
Abstract: In order to achieve high data rate and increase the
spectral efficiency, multiple input multiple output (MIMO) system has
been proposed. However, multiple antennas are limited by size and
cost. Therefore, recently developed cooperative diversity scheme,
which profits the transmit diversity only with the existing hardware by
constituting a virtual antenna array, can be a solution. However, most
of the introduced cooperative techniques have a common fault of
decreased transmission rate because the destination should receive the
decodable compositions of symbols from the source and the relay. In
this paper, we propose a cooperative cyclic delay diversity (CDD)
scheme that use hierarchical modulation. This scheme is free from the
rate loss and allows seamless cooperative communication.
Abstract: This paper treats different aspects of entropy measure
in classical information theory and statistical quantum mechanics, it
presents the possibility of extending the definition of Von Neumann
entropy to image and array processing. In the first part, we generalize
the quantum entropy using singular values of arbitrary rectangular
matrices to measure the randomness and the quality of denoising
operation, this new definition of entropy can be implemented to
compare the performance analysis of filtering methods. In the second
part, we apply the concept of pure state in quantum formalism
to generalize the maximum entropy method for narrowband and
farfield source localization problem. Several computer simulation
results are illustrated to demonstrate the effectiveness of the proposed
techniques.
Abstract: In this study, a multi objective optimization for end
milling of Al 6061 alloy has been presented to provide better
surface quality and higher Material Removal Rate (MRR). The input
parameters considered for the analysis are spindle speed, depth of cut
and feed. The experiments were planned as per Taguchis design of
experiment, with L27 orthogonal array. The Grey Relational Analysis
(GRA) has been used for transforming multiple quality responses
into a single response and the weights of the each performance
characteristics are determined by employing the Principal Component
Analysis (PCA), so that their relative importance can be properly and
objectively described. The results reveal that Taguchi based G-PCA
can effectively acquire the optimal combination of cutting parameters.
Abstract: Nine Degrees of Freedom (9 DOF) systems are
already in development in many areas. In this paper, an integrated
pressure sensor is proposed that will make use of an already existing
monolithic 9 DOF inertial MEMS platform. Capacitive pressure
sensors can suffer from limited sensitivity for a given size of
membrane. This novel pressure sensor design increases the sensitivity
by over 5 times compared to a traditional array of square diaphragms
while still fitting within a 2 mm x 2 mm chip and maintaining a fixed
static capacitance. The improved design uses one large diaphragm
supported by pillars with fixed electrodes placed above the areas of
maximum deflection. The design optimization increases the
sensitivity from 0.22 fF/kPa to 1.16 fF/kPa. Temperature sensitivity
was also examined through simulation.
Abstract: Al6061 alloy base matrix, reinforced with particles of
silicon carbide (10 wt %) and Graphite powder (1wt%), known as
hybrid composites have been fabricated by liquid metallurgy route
(stir casting technique) and optimized at different parameters like
applied load, sliding speed and sliding distance by taguchi method. A
plan of experiment generated through taguchi technique was used to
perform experiments based on L27 orthogonal array. The developed
ANOVA and regression equations are used to find the optimum
coefficient of friction and wear under the influence of applied load,
sliding speed and sliding distance. On the basis of “smaller the best”
the dry sliding wear resistance was analysed and finally confirmation
tests were carried out to verify the experimental results.
Abstract: In this paper, we propose a system for preventing gas
risks through the use of wireless communication modules and
intelligent gas safety appliances. Our system configuration consists of
an automatic extinguishing system, detectors, a wall-pad, and a
microcomputer controlled micom gas meter to monitor gas flow and
pressure as well as the occurrence of earthquakes. The automatic fire
extinguishing system checks for both combustible gaseous leaks and
monitors the environmental temperature, while the detector array
measures smoke and CO gas concentrations. Depending on detected
conditions, the micom gas meter cuts off an inner valve and generates
a warning, the automatic fire-extinguishing system cuts off an external
valve and sprays extinguishing materials, or the sensors generate
signals and take further action when smoke or CO are detected.
Information on intelligent measures taken by the gas safety appliances
and sensors are transmitted to the wall-pad, which in turn relays this as
real time data to a server that can be monitored via an external network
(BcN) connection to a web or mobile application for the management
of gas safety. To validate this smart-home gas management system, we
field-tested its suitability for use in Korean apartments under several
scenarios.
Abstract: This paper reports a novel actuating design that uses
the shear deformation of a piezoelectric actuator to deflect a
bulge-diaphragm for driving an array microdroplet ejector. In essence,
we employed a circular-shaped actuator poled radial direction with
remnant polarization normal to the actuating electric field for inducing
the piezoelectric shear effect. The array microdroplet ejector consists
of a shear type piezoelectric actuator, a vibration plate, two chamber
plates, two channel plates and a nozzle plate. The vibration, chamber
and nozzle plate components are fabricated using nickel
electroforming technology, whereas the channel plate is fabricated by
etching of stainless steel. The diaphragm displacement was measured
by the laser two-dimensional scanning vibrometer. The ejected
droplets of the microejector were also observed via an optic
visualization system.
Abstract: Latin hypercube designs (LHDs) have been applied in
many computer experiments among the space-filling designs found in
the literature. A LHD can be randomly generated but a randomly
chosen LHD may have bad properties and thus act poorly in
estimation and prediction. There is a connection between Latin
squares and orthogonal arrays (OAs). A Latin square of order s
involves an arrangement of s symbols in s rows and s columns, such
that every symbol occurs once in each row and once in each column
and this exists for every non-negative integer s. In this paper, a
computer program was written to construct orthogonal array-based
Latin hypercube designs (OA-LHDs). Orthogonal arrays (OAs) were
constructed from Latin square of order s and the OAs constructed
were afterward used to construct the desired Latin hypercube designs
for three input variables for use in computer experiments. The LHDs
constructed have better space-filling properties and they can be used
in computer experiments that involve only three input factors.
MATLAB 2012a computer package (www.mathworks.com/) was
used for the development of the program that constructs the designs.
Abstract: Array-based gene expression analysis is a powerful
tool to profile expression of genes and to generate information on
therapeutic effects of new anti-cancer compounds. Anti-apoptotic
effect of thymoquinone was studied in MCF7 breast cancer cell line
using gene expression profiling with cDNA microarray. The purity
and yield of RNA samples were determined using RNeasyPlus Mini
kit. The Agilent RNA 6000 NanoLabChip kit evaluated the quantity
of the RNA samples. AffinityScript RT oligo-dT promoter primer
was used to generate cDNA strands. T7 RNA polymerase was used to
convert cDNA to cRNA. The cRNA samples and human universal
reference RNA were labelled with Cy-3-CTP and Cy-5-CTP,
respectively. Feature Extraction and GeneSpring softwares analysed
the data. The single experiment analysis revealed involvement of 64
pathways with up-regulated genes and 78 pathways with downregulated
genes. The MAPK and p38-MAPK pathways were
inhibited due to the up-regulation of PTPRR gene. The inhibition of
p38-MAPK suggested up-regulation of TGF-ß pathway. Inhibition of
p38-MAPK caused up-regulation of TP53 and down-regulation of
Bcl2 genes indicating involvement of intrinsic apoptotic pathway.
Down-regulation of CARD16 gene as an adaptor molecule regulated
CASP1 and suggested necrosis-like programmed cell death and
involvement of caspase in apoptosis. Furthermore, down-regulation
of GPCR, EGF-EGFR signalling pathways suggested reduction of
ER. Involvement of AhR pathway which control cytochrome P450
and glucuronidation pathways showed metabolism of Thymoquinone.
The findings showed differential expression of several genes in
apoptosis pathways with thymoquinone treatment in estrogen
receptor-positive breast cancer cells.
Abstract: This paper discusses the design and analysis of a
hybrid PV-Fuel cell energy system destined to power a DC load. The
system is composed of a photovoltaic array, a fuel cell, an
electrolyzer and a hydrogen tank. HOMER software is used in this
study to calculate the optimum capacities of the power system
components that their combination allows an efficient use of solar
resource to cover the hourly load needs. The optimal system sizing
allows establishing the right balance between the daily electrical
energy produced by the power system and the daily electrical energy
consumed by the DC load using a 28 KW PV array, a 7.5 KW fuel
cell, a 40KW electrolyzer and a 270 Kg hydrogen tank. The variation
of powers involved into the DC bus of the hybrid PV-fuel cell system
has been computed and analyzed for each hour over one year: the
output powers of the PV array and the fuel cell, the input power of
the elctrolyzer system and the DC primary load. Equally, the annual
variation of stored hydrogen produced by the electrolyzer has been
assessed. The PV array contributes in the power system with 82%
whereas the fuel cell produces 18%. 38% of the total energy
consumption belongs to the DC primary load while the rest goes to
the electrolyzer.
Abstract: Semiconductor crystals smaller than about 10 nm,
known as quantum dots, have properties that differ from large
samples, including a band gap that becomes larger for smaller
particles. These properties create several applications for quantum
dots. In this paper new shapes of quantum dot arrays are used to
enhance the photo physical properties of gold nano-particles. This
paper presents a study of the effect of nano-particles shape, array, and
size on their absorption characteristics.
Abstract: The present work analyses different parameters of end
milling to minimize the surface roughness for AISI D2 steel. D2 Steel
is generally used for stamping or forming dies, punches, forming
rolls, knives, slitters, shear blades, tools, scrap choppers, tyre
shredders etc. Surface roughness is one of the main indices that
determines the quality of machined products and is influenced by
various cutting parameters. In machining operations, achieving
desired surface quality by optimization of machining parameters, is a
challenging job. In case of mating components the surface roughness
become more essential and is influenced by the cutting parameters,
because, these quality structures are highly correlated and are
expected to be influenced directly or indirectly by the direct effect of
process parameters or their interactive effects (i.e. on process
environment). In this work, the effects of selected process parameters
on surface roughness and subsequent setting of parameters with the
levels have been accomplished by Taguchi’s parameter design
approach. The experiments have been performed as per the
combination of levels of different process parameters suggested by
L9 orthogonal array. Experimental investigation of the end milling of
AISI D2 steel with carbide tool by varying feed, speed and depth of
cut and the surface roughness has been measured using surface
roughness tester. Analyses of variance have been performed for mean
and signal-to-noise ratio to estimate the contribution of the different
process parameters on the process.
Abstract: Zinc oxide (ZnO) is one of the light emitting materials in ultraviolet (UV) region. In addition, ZnO nanostructures are also attracting increasing research interest as buildingblocks for UV optoelectronic applications. We have succeeded in synthesizing vertically-aligned ZnO nanostructures by laser interference patterning, which is catalyst-free and non-contact technique. In this study, vertically-aligned ZnO nanowall arrays were synthesized using two-beam interference. The maximum height and average thickness of the ZnO nanowalls were about 4.5µm and 200 nm, respectively.UV lasing from a piece of the ZnO nanowall was obtained under the third harmonic of a Q-switched Nd:YAG laser excitation, and the estimated threshold power density for lasing was about 150 kW/cm2. Furthermore, UV lasing from the vertically-aligned ZnO nanowall was also achieved. The results indicate that ZnO nanowalls can be applied to random laser.
Abstract: The paper presents a practical three-phase PWM
inverter suitable for low voltage, low rating energy efficient systems.
The work in the paper is conducted with the view to establishing the
significance of the loss contribution from the PWM inverter in the
determination of the complete losses of a photovoltaic (PV) arraypowered
induction motor drive water pumping system. Losses
investigated include; conduction and switching loss of the devices
and gate drive losses. It is found that the PWM inverter operates at a
reasonable variable efficiency that does not fall below 92%
depending on the load. The results between the simulated and
experimental results for the system with or without a maximum
power tracker (MPT) compares very well, within an acceptable range
of 2% margin.
Abstract: Development of a method to estimate gene functions is
an important task in bioinformatics. One of the approaches for the
annotation is the identification of the metabolic pathway that genes are
involved in. Since gene expression data reflect various intracellular
phenomena, those data are considered to be related with genes’
functions. However, it has been difficult to estimate the gene function
with high accuracy. It is considered that the low accuracy of the
estimation is caused by the difficulty of accurately measuring a gene
expression. Even though they are measured under the same condition,
the gene expressions will vary usually. In this study, we proposed a
feature extraction method focusing on the variability of gene
expressions to estimate the genes' metabolic pathway accurately. First,
we estimated the distribution of each gene expression from replicate
data. Next, we calculated the similarity between all gene pairs by KL
divergence, which is a method for calculating the similarity between
distributions. Finally, we utilized the similarity vectors as feature
vectors and trained the multiclass SVM for identifying the genes'
metabolic pathway. To evaluate our developed method, we applied the
method to budding yeast and trained the multiclass SVM for
identifying the seven metabolic pathways. As a result, the accuracy
that calculated by our developed method was higher than the one that
calculated from the raw gene expression data. Thus, our developed
method combined with KL divergence is useful for identifying the
genes' metabolic pathway.
Abstract: A numerical study of natural convection heat transfer
in water filled cavity has been examined in 3-Dfor single phase liquid
cooling system by using an array of parallel plate fins mounted to one
wall of a cavity. The heat generated by a heat source represents a
computer CPU with dimensions of 37.5∗37.5mm mounted on
substrate. A cold plate is used as a heat sink installed on the opposite
vertical end of the enclosure. The air flow inside the computer case is
created by an exhaust fan. A turbulent air flow is assumed and k-ε
model is applied. The fins are installed on the substrate to enhance
the heat transfer. The applied power energy range used is between 15
- 40W. In order to determine the thermal behaviour of the cooling
system, the effect of the heat input and the number of the parallel
plate fins are investigated. The results illustrate that as the fin number
increases the maximum heat source temperature decreases. However,
when the fin number increases to critical value the temperature start
to increase due to the fins are too closely spaced and that cause the
obstruction of water flow. The introduction of parallel plate fins
reduces the maximum heat source temperature by 10% compared to
the case without fins. The cooling system maintains the maximum
chip temperature at 64.68°C when the heat input was at 40W that is
much lower than the recommended computer chips limit temperature
of no more than 85°C and hence the performance of the CPU is
enhanced.
Abstract: Analyzing DNA microarray data sets is a great
challenge, which faces the bioinformaticians due to the complication
of using statistical and machine learning techniques. The challenge
will be doubled if the microarray data sets contain missing data,
which happens regularly because these techniques cannot deal with
missing data. One of the most important data analysis process on
the microarray data set is feature selection. This process finds the
most important genes that affect certain disease. In this paper, we
introduce a technique for imputing the missing data in microarray
data sets while performing feature selection.