Abstract: Modern low earth orbit (LEO) satellites that require multi-mission flexibility are highly likely to be repositioned between different operational orbits. While executing this process the satellite may experience high levels of vibration and environmental hazards, exposing the deployed solar panel to dangerous stress levels, fatigue and space debris, hence it is desirable to retract the solar array before satellite repositioning to avoid damage or failure.
A novel concept of deployable/retractable hybrid solar array systemcomposed of both rigid and flexible solar panels arranged within a petal formation, aimed to provide a greater power to volume ratio while dramatically reducing mass and cost is proposed.
Abstract: Locating Radio Controlled (RC) devices using their
unintended emissions has a great interest considering security
concerns. Weak nature of these emissions requires near field
localization approach since it is hard to detect these signals in far
field region of array. Instead of only angle estimation, near field
localization also requires range estimation of the source which makes
this method more complicated than far field models. Challenges of
locating such devices in a near field region and real time environment
are analyzed in this paper. An ESPRIT like near field localization
scheme is utilized for both angle and range estimation. 1-D search
with symmetric subarrays is provided. Two 7 element uniform linear
antenna arrays (ULA) are employed for locating RC source.
Experiment results of location estimation for one unintended emitting
walkie-talkie for different positions are given.
Abstract: In this paper we describe the Levenvberg-Marquardt
(LM) algorithm for identification and equalization of CDMA
signals received by an antenna array in communication channels.
The synthesis explains the digital separation and equalization of
signals after propagation through multipath generating intersymbol
interference (ISI). Exploiting discrete data transmitted and three
diversities induced at the reception, the problem can be composed
by the Block Component Decomposition (BCD) of a tensor of
order 3 which is a new tensor decomposition generalizing the
PARAFAC decomposition. We optimize the BCD decomposition by
Levenvberg-Marquardt method gives encouraging results compared to
classical alternating least squares algorithm (ALS). In the equalization
part, we use the Minimum Mean Square Error (MMSE) to perform
the presented method. The simulation results using the LM algorithm
are important.
Abstract: In this work, neural networks methods MLP type were
applied to a database from an array of six sensors for the detection of
three toxic gases. The choice of the number of hidden layers and the
weight values are influential on the convergence of the learning
algorithm. We proposed, in this article, a mathematical formula to
determine the optimal number of hidden layers and good weight
values based on the method of back propagation of errors. The results
of this modeling have improved discrimination of these gases and
optimized the computation time. The model presented here has
proven to be an effective application for the fast identification of
toxic gases.
Abstract: Several of the practical industrial control processes are
multivariable processes. Due to the relation amid the variables
(interaction), delay in the loops, it is very intricate to design a
controller directly for these processes. So first, the interaction of the
variables is analyzed using Relative Normalized Gain Array
(RNGA), which considers the time constant, static gain and delay
time of the processes. Based on the effect of RNGA, relative gain
array (RGA) and NI, the pair (control configuration) of variables to
be controlled by decentralized control is selected. The equivalent
transfer function (ETF) of the process model is estimated as first
order process with delay using the corresponding elements in the
Relative gain array and Relative average residence time array
(RARTA) of the processes. Secondly, a decentralized Proportional-
Integral (PI) controller is designed for each ETF simply using
frequency response specifications. Finally, the performance and
robustness of the algorithm is comparing with existing related
approaches to validate the effectiveness of the projected algorithm.
Abstract: The electric power supplied by a photovoltaic power
generation systems depends on the solar irradiation and temperature.
The PV system can supply the maximum power to the load at a
particular operating point which is generally called as maximum
power point (MPP), at which the entire PV system operates with
maximum efficiency and produces its maximum power. Hence, a
Maximum power point tracking (MPPT) methods are used to
maximize the PV array output power by tracking continuously the
maximum power point. The proposed MPPT controller is designed
for 10kW solar PV system installed at Cape Institute of Technology.
This paper presents the fuzzy logic based MPPT algorithm. However,
instead of one type of membership function, different structures of
fuzzy membership functions are used in the FLC design. The
proposed controller is combined with the system and the results are
obtained for each membership functions in Matlab/Simulink
environment. Simulation results are decided that which membership
function is more suitable for this system.
Abstract: Particles are the most common and cheapest
reinforcement producing discontinuous reinforced composites with
isotropic properties. Conventional fabrication methods can be used to
produce a wide range of product forms, making them relatively
inexpensive. Optimising composite development must include
consideration of all the fundamental aspect of particles including
their size, shape, volume fraction, distribution and mechanical
properties. Research has shown that the challenges of low fracture
toughness, poor crack growth resistance and low thermal stability can
be overcome by reinforcement with particles. The unique properties
exhibited by micro particles reinforced ceramic composites have
made them to be highly attractive in a vast array of applications.
Abstract: Renewable energy is derived from natural processes
that are replenished constantly. Included in the definition is
electricity and heat generated from solar, wind, ocean, hydropower,
biomass, geothermal resources, and bio-fuels and hydrogen derived
from renewable resources. Each of these sources has unique
characteristics which influence how and where they are used. This
paper presents the modeling the simulation of solar and hydro hybrid
energy sources in MATLAB/SIMULINK environment. It simulates
all quantities of Hybrid Electrical Power system (HEPS) such as AC
output current of the inverter that injected to the load/grid, load
current, grid current. It also simulates power output from PV and
Hydraulic Turbine Generator (HTG), power delivered to or from grid
and finally power factor of the inverter for PV, HTG and grid. The
proposed circuit uses instantaneous p-q (real-imaginary) power
theory.
Abstract: Microarray technology is universally used in the study
of disease diagnosis using gene expression levels. The main
shortcoming of gene expression data is that it includes thousands of
genes and a small number of samples. Abundant methods and
techniques have been proposed for tumor classification using
microarray gene expression data. Feature or gene selection methods
can be used to mine the genes that directly involve in the
classification and to eliminate irrelevant genes. In this paper
statistical measures like T-Statistics, Signal-to-Noise Ratio (SNR)
and F-Statistics are used to rank the genes. The ranked genes are used
for further classification. Particle Swarm Optimization (PSO)
algorithm and Shuffled Frog Leaping (SFL) algorithm are used to
find the significant genes from the top-m ranked genes. The Naïve
Bayes Classifier (NBC) is used to classify the samples based on the
significant genes. The proposed work is applied on Lung and Ovarian
datasets. The experimental results show that the proposed method
achieves 100% accuracy in all the three datasets and the results are
compared with previous works.
Abstract: The phased-array ultrasound transducer types are
utilities for medical ultrasonography as well as optical imaging.
However, their discontinuity characteristic limits the applications due
to the artifacts contaminated into the reconstructed images. Because
of the effects of the ultrasound pressure field pattern to the echo
ultrasonic waves as well as the optical modulated signal, the side
lobes of the focused ultrasound beam induced by discontinuity of the
phased-array ultrasound transducer might the reason of the artifacts.
In this paper, a simple method in approach of numerical simulation
was used to investigate the limitation of discontinuity of the elements
in phased-array ultrasound transducer and their effects to the
ultrasound pressure field. Take into account the change of ultrasound
pressure field patterns in the conditions of variation of the pitches
between elements of the phased-array ultrasound transducer, the
appropriated parameters for phased-array ultrasound transducer
design were asserted quantitatively.
Abstract: In this paper two approaches to joint signal detection,
time of arrival (ToA) and angle of arrival (AoA) estimation in
multi-element antenna array are investigated. Two scenarios were
considered: first one, when the waveform of the useful signal
is known a priori and, second one, when the waveform of the
desired signal is unknown. For first scenario, the antenna array
signal processing based on multi-element matched filtering (MF)
with the following non-coherent detection scheme and maximum
likelihood (ML) parameter estimation blocks is exploited. For second
scenario, the signal processing based on the antenna array elements
covariance matrix estimation with the following eigenvector analysis
and ML parameter estimation blocks is applied. The performance
characteristics of both signal processing schemes are thoroughly
investigated and compared for different useful signals and noise
parameters.
Abstract: The mathematical analysis on radiation obtained and
the development of the solar photovoltaic (PV) array groundwater
pumping is needed in the rural areas of Thohoyandou for sizing and
power performance subject to the climate conditions within the area.
A simple methodology approach is developed for the directed
coupled solar, controller and submersible ground water pump system.
The system consists of a PV array, pump controller and submerged
pump, battery backup and charger controller. For this reason, the
theoretical solar radiation is obtained for optimal predictions and
system performance in order to achieve different design and
operating parameters. Here the examination of the PV schematic
module in a Direct Current (DC) application is used for obtainable
maximum solar power energy for water pumping. In this paper, a
simple efficient photovoltaic water pumping system is presented with
its theoretical studies and mathematical modeling of photovoltaics
(PV) system.
Abstract: The aim of this work is to present a theoretical analysis of a 2D ultrasound transducer comprised of crossed arrays of metal strips placed on both sides of thin piezoelectric layer (a). Such a structure is capable of electronic beam-steering of generated wavebeam both in elevation and azimuth. In this paper a semi-analytical model of the considered transducer is developed. It is based on generalization of the well-known BIS-expansion method. Specifically, applying the electrostatic approximation, the electric field components on the surface of the layer are expanded into fast converging series of double periodic spatial harmonics with corresponding amplitudes represented by the properly chosen Legendre polynomials. The problem is reduced to numerical solving of certain system of linear equations for unknown expansion coefficients.
Abstract: The paper presents the results of clusterization by
Kohonen self-organizing maps (SOM) applied for analysis of array of
Raman spectra of multi-component solutions of inorganic salts, for
determination of types of salts present in the solution. It is
demonstrated that use of SOM is a promising method for solution of
clusterization and classification problems in spectroscopy of multicomponent
objects, as attributing a pattern to some cluster may be
used for recognition of component composition of the object.
Abstract: This paper presents the design and analysis of Liquid
Crystal (LC) based tunable reflectarray antenna with different design
configurations within X-band frequency range. The effect of LC
volume used for unit cell element on frequency tunability and
reflection loss performance has been investigated. Moreover different
slot embedded patch element configurations have been proposed for
LC based tunable reflectarray antenna design with enhanced
performance. The detailed fabrication and measurement procedure
for different LC based unit cells has been presented. The waveguide
scattering parameter measured results demonstrated that by using the
circular slot embedded patch elements, the frequency tunability and
dynamic phase range can be increased from 180MHz to 200MHz and
120° to 124° respectively. Furthermore the circular slot embedded
patch element can be designed at 10GHz resonant frequency with a
patch volume of 2.71mm3 as compared to 3.47mm3 required for
rectangular patch without slot.
Abstract: This paper presents the design and analysis of Liquid
Crystal (LC) based tunable reflectarray antenna with different design
configurations within X-band frequency range. The effect of LC
volume used for unit cell element on frequency tunability and
reflection loss performance has been investigated. Moreover different
slot embedded patch element configurations have been proposed for
LC based tunable reflectarray antenna design with enhanced
performance. The detailed fabrication and measurement procedure
for different LC based unit cells has been presented. The waveguide
scattering parameter measured results demonstrated that by using the
circular slot embedded patch elements, the frequency tunability and
dynamic phase range can be increased from 180MHz to 200MHz and
120° to 124° respectively. Furthermore the circular slot embedded
patch element can be designed at 10GHz resonant frequency with a
patch volume of 2.71mm3 as compared to 3.47mm3 required for
rectangular patch without slot.
Abstract: This paper presents the findings of an experimental investigation of important machining parameters for the horizontal boring tool modified to mouth with a horizontal lathe machine to bore an overlength workpiece. In order to verify a usability of a modified tool, design of experiment based on Taguchi method is performed. The parameters investigated are spindle speed, feed rate, depth of cut and length of workpiece. Taguchi L9 orthogonal array is selected for four factors three level parameters in order to minimize surface roughness (Ra and Rz) of S45C steel tubes. Signal to noise ratio analysis and analysis of variance (ANOVA) is performed to study an effect of said parameters and to optimize the machine setting for best surface finish. The controlled factors with most effect are depth of cut, spindle speed, length of workpiece, and feed rate in order. The confirmation test is performed to test the optimal setting obtained from Taguchi method and the result is satisfactory.
Abstract: Most of the PV systems are designed with transformer for safety purpose with galvanic isolation. However, the transformer is big, heavy and expensive. Also, it reduces the overall frequency of the conversion stage. Generally PV inverter with transformer is having efficiency around 92%–94% only. To overcome these problems, transformerless PV system is introduced. It is smaller, lighter, cheaper and higher in efficiency. However, dangerous leakage current will flow between PV array and the grid due to the stray capacitance. There are different types of configurations available for transformerless inverters like H5, H6, HERIC, oH5, and Dual paralleled buck inverter. But each configuration is suffering from its own disadvantages like high conduction losses, shoot-through issues of switches, dead-time requirements at zero crossing instants of grid voltage to avoid grid shoot-through faults and MOSFET reverse recovery issues. The main objective of the proposed transformerless inverter is to address two key issues: One key issue for a transformerless inverter is that it is necessary to achieve high efficiency compared to other existing inverter topologies. Another key issue is that the inverter configuration should not have any shoot-through issues for higher reliability.
Abstract: In this study, Electrical Discharge Machining (EDM) is used to modify the surface of high carbon steel En31 with the help of tool electrode (Copper-Chromium-Nickel) manufactured by powder metallurgy (PM) process. The effect of EDM on surface roughness during surface alloying is studied. Taguchi’s Design of experiment (DOE) and L18 orthogonal array is used to find the best level of input parameters in order to achieve high surface finish. Six input parameters are considered and their percentage contribution towards surface roughness is investigated by analysis of variances (ANOVA). Experimental results show that an hard alloyed surface (1.21% carbon, 2.14% chromium and 1.38% nickel) with surface roughness of 3.19µm can be generated using EDM with PM tool. Additionally, techniques like Scanning Electron Microscope (SEM) and Energy Dispersive Spectroscopy (EDS) are used to analyze the machined surface and EDMed layer composition, respectively. The increase in machined surface micro-hardness (101%) may be related to the formation of carbides containing chromium.
Abstract: The scope of this paper is to evaluate and compare the potential of LS-PV(Large Scale Photovoltaic Power Plant) power generation systems in the southern region of Libya at Al-Kufra for both stationary and tracking systems. A Microsoft Excel-VBA program has been developed to compute slope radiation, dew-point, sky temperature, and then cell temperature, maximum power output and module efficiency of the system for stationary system and for tracking system. The results for energy production show that the total energy output is 114GWh/year for stationary system and 148GWh/year for tracking system. The average module efficiency for the stationary system is 16.6% and 16.2% for the tracking system.
The values of electricity generation capacity factor (CF) and solar capacity factor (SCF) for stationary system were found to be 26% and 62.5% respectively and 34% and 82% for tracking system. The GCR (Ground Cover Ratio) for a stationary system is 0.7, which corresponds to a tilt angle of 24°. The GCR for tracking system was found to be 0.12. The estimated ground area needed to build a 50MW PV plant amounts to approx. 0.55km2 for a stationary PV field constituted by HIT PV arrays and approx. 91MW/ km2. In case of a tracker PV field, the required ground area amounts approx.2.4km2 and approx. 20.5MW/ km2.