Abstract: Turbulence modeling of large-scale flow over a vegetated surface is complex. Such problems involve large scale computational domains, while the characteristics of flow near the surface are also involved. In modeling large scale flow, surface roughness including vegetation is generally taken into account by mean of roughness parameters in the modified law of the wall. However, the turbulence structure within the canopy region cannot be captured with this method, another method which applies source/sink terms to model plant drag can be used. These models have been developed and tested intensively but with a simple surface geometry. This paper aims to compare the use of roughness parameter, and additional source/sink terms in modeling the effect of plant drag on wind flow over a complex vegetated surface. The RNG k-ε turbulence model with the non-equilibrium wall function was tested with both cases. In addition, the k-ω turbulence model, which is claimed to be computationally stable, was also investigated with the source/sink terms. All numerical results were compared to the experimental results obtained at the study site Mason Bay, Stewart Island, New Zealand. In the near-surface region, it is found that the results obtained by using the source/sink term are more accurate than those using roughness parameters. The k-ω turbulence model with source/sink term is more appropriate as it is more accurate and more computationally stable than the RNG k-ε turbulence model. At higher region, there is no significant difference amongst the results obtained from all simulations.
Abstract: Aluminum alloy sheets have several advantages such
as the lightweight, high-specific strength and recycling efficiency.
Therefore, aluminum alloy sheets in sheet forming have been used in various areas as automotive components and so forth. During the
process of sheet forming, wrinkling which is caused by compression stress might occur and the formability of sheets was affected by
occurrence of wrinkling. A few studies of uniaxial compressive test by
using square tubes, pipes and sheets were carried out to clarify the each wrinkling behavior. However, on uniaxial compressive test,
deformation behavior of the sheets hasn-t be cleared. Then, it is necessary to clarify the relationship between the buckling behavior
and the forming conditions. In this study, the effect of dimension of the sheet in the buckling behavior on compression test of aluminum alloy sheet was cleared by experiment and FEA. As the results, the buckling
deformation was classified by three modes in terms of the distribution of equivalent plastic strain.
Abstract: Recently, majors of doctors are divided into terribly lots of detailed areas. However, it is actually not a rare case that a doctor has a patient who is not in his/her major. He/She must judge an assessment and make a medical treatment plan for this patient. According to our investigation, conventional approaches such as image diagnosis cooperation are insufficient. This paper proposes an 'Assessment / Medical Treatment Plan Consulting System'. We have implemented a pilot system based on our proposition. Its effectiveness is clarified by an evaluation.
Abstract: This paper is a simple and systematic approaches to the design and analysis a pulse width modulation (PWM) based sliding mode controller for buck DC-DC Converters. Various aspects of the design, including the practical problems and the proposed solutions, are detailed. However, these control strategies can't compensate for large load current and input voltage variations. In this paper, a new control strategy by compromising both schemes advantages and avoiding their drawbacks is proposed, analyzed and simulated.
Abstract: In this paper, a method based on Non-Dominated
Sorting Genetic Algorithm (NSGA) has been presented for the Volt /
Var control in power distribution systems with dispersed generation
(DG). Genetic algorithm approach is used due to its broad
applicability, ease of use and high accuracy. The proposed method is
better suited for volt/var control problems. A multi-objective
optimization problem has been formulated for the volt/var control of
the distribution system. The non-dominated sorting genetic algorithm
based method proposed in this paper, alleviates the problem of tuning
the weighting factors required in solving the multi-objective volt/var
control optimization problems. Based on the simulation studies
carried out on the distribution system, the proposed scheme has been
found to be simple, accurate and easy to apply to solve the multiobjective
volt/var control optimization problem of the distribution
system with dispersed generation.
Abstract: The integral form of equations of motion of composite
beams subjected to varying time loads are discretized using a
developed finite element model. The model consists of a straight five
node twenty-two degrees of freedom beam element. The stability
analysis of the beams is studied by solving the matrix form
characteristic equations of the system. The principle of virtual work
and the first order shear deformation theory are employed to analyze
the beams with large deformation and small strains. The regions of
dynamic instability of the beam are determined by solving the
obtained Mathieu form of differential equations. The effects of nonconservative
loads, shear stiffness, and damping parameters on
stability and response of the beams are examined. Several numerical
calculations are presented to compare the results with data reported
by other researchers.
Abstract: This study is aimed to investigate feasibility of the
aerobic biological process to treat oily wastewater from palm oil food
industry. Effect of aeration and sludge concentrations are studied.
Raw sludge and raw wastewater was mixed and acclimatized for five
days in a stirred tank reactor. The aeration rate (no aeration, low;
1.5L/min and high rate; 2L/min) and sludge concentration (3675,
7350, and 11025mg/L of VSS) were varied. Responses of process
were pH, COD, oil and grease, VSS, and PHB content. It was found
that the treatment can remove 85.1 to 97.1 % of COD and remove
12.9 to 54.8% of oil & grease. The PHB yield was found to be within
0.15% to 2.4% as PHB/VSS ratio and 0.01% to 0.12% as PHB/COD
removed. The higher aeration results a high COD removal and oil &
grease removal, while experiment without aeration gives better PHB
yield. Higher sludge concentrations (11025mg/L VSS) give higher
removal of oil & grease while moderate sludge concentration
(7350mg/L VSS) give better result in COD removal. Higher PHB
yield is obtained in low sludge concentration (3675mg/L).
Abstract: The paper compares different channel models used for
modeling Broadband Power-Line Communication (BPLC) system.
The models compared are Zimmermann and Dostert, Philipps,
Anatory et al and Anatory et al generalized Transmission Line (TL)
model. The validity of each model was compared in time domain
with ATP-EMTP software which uses transmission line approach. It
is found that for a power-line network with minimum number of
branches all the models give similar signal/pulse time responses
compared with ATP-EMTP software; however, Zimmermann and
Dostert model indicates the same amplitude but different time delay.
It is observed that when the numbers of branches are increased only
generalized TL theory approach results are comparable with ATPEMTP
results. Also the Multi-Carrier Spread Spectrum (MC-SS)
system was applied to check the implication of such behavior on the
modulation schemes. It is observed that using Philipps on the
underground cable can predict the performance up to 25dB better
than other channel models which can misread the actual performance
of the system. Also modified Zimmermann and Dostert under
multipath can predict a better performance of about 5dB better than
the actual predicted by Generalized TL theory. It is therefore
suggested for a realistic BPLC system design and analyses the model
based on generalized TL theory be used.
Abstract: Even it has been recognized that Shape Memory
Alloys (SMA) have a significant potential for deployment actuators,
the number of applications of SMA-based actuators to the present
day is still quite small, due to the need of deep understanding of the
thermo-mechanical behavior of SMA, causing an important need for
a mathematical model able to describe all thermo-mechanical
properties of SMA by relatively simple final set of constitutive
equations. SMAs offer attractive potentials such as: reversible strains
of several percent, generation of high recovery stresses and high
power / weight ratios. The paper tries to provide an overview of the
shape memory functions and a presentation of the designed and
developed temperature control system used for a gripper actuated by
two pairs of differential SMA active springs. An experimental setup
was established, using electrical energy for actuator-s springs heating
process. As for holding the temperature of the SMA springs at certain
level for a long time was developed a control system in order to
avoid the active elements overheating.
Abstract: A climate dependent model is proposed to simulate
the population of Aedes aegypti mosquito. In developing the model,
average temperature of Shah Alam, Malaysia was used to determine
the development rate of each stage of the life cycle of mosquito.
Rainfall dependent function was proposed to simulate the hatching
rate of the eggs under several assumptions. The proposed transition
matrix was obtained and used to simulate the population of eggs,
larvae, pupae and adults mosquito. It was found that the peak of
mosquito abundance comes during a relatively dry period following a
heavy rainfall. In addition, lag time between the peaks of mosquito
abundance and dengue fever cases in Shah Alam was estimated.
Abstract: In this paper the complete rotor system including
elastic shaft with distributed mass, allowing for the effects of oil film
in bearings. Also, flexibility of foundation is modeled. As a whole
this article is a relatively complete research in modeling and
vibration analysis of rotor considering gyroscopic effect, damping,
dependency of stiffness and damping coefficients on frequency and
solving the vibration equations including these parameters. On the
basis of finite element method and utilizing four element types
including element of shaft, disk, bearing and foundation and using
MATLAB, a computer program is written. So the responses in
several cases and considering different effects are obtained. Then the
results are compared with each other, with exact solutions and results
of other papers.
Abstract: In this investigation, anatase TiO2 thin films were
grown by radio frequency magnetron sputtering on glass substrates at
a high sputtering pressure and room temperature. The anatase films
were then annealed at 300-600 °C in air for a period of 1 hour. To
examine the structure and morphology of the films, X-ray diffraction
(XRD) and atomic force microscopy (AFM) methods were used
respectively. From X-ray diffraction patterns of the TiO2 films, it was
found that the as-deposited film showed some differences compared
with the annealed films and the intensities of the peaks of the
crystalline phase increased with the increase of annealing
temperature. From AFM images, the distinct variations in the
morphology of the thin films were also observed. The optical
constants were characterized using the transmission spectra of the
films obtained by UV-VIS-IR spectrophotometer. Besides, optical
thickness of the film deposited at room temperature was calculated
and cross-checked by taking a cross-sectional image through SEM.
The optical band gaps were evaluated through Tauc model. It was
observed that TiO2 films produced at room temperatures exhibited
high visible transmittance and transmittance decreased slightly with
the increase of annealing temperatures. The films were found to be
crystalline having anatase phase. The refractive index of the films
was found from 2.31-2.35 in the visible range. The extinction
coefficient was nearly zero in the visible range and was found to
increase with annealing temperature. The allowed indirect optical
band gap of the films was estimated to be in the range from 3.39 to
3.42 eV which showed a small variation. The allowed direct band
gap was found to increase from 3.67 to 3.72 eV. The porosity was
also found to decrease at a higher annealing temperature making the
film compact and dense.
Abstract: This experiment was conducted in attempt of
improving hydrodynamic efficiency of the propulsion mechanism by
installing a spring to the wing so that the opening angle of the wing in
one stroke can be changed automatically, compared to the existing
method of fixed maximum opening angle in Weis-Fogh type ship
propulsion mechanism. Average thrust coefficient was almost fixed
with all velocity ratio with the prototype, but with the spring type,
thrust coefficient increased sharply as velocity ratio increased.
Average propulsive efficiency was larger with bigger opening angle in
the prototype, but in the spring type, the one with smaller spring
coefficient had larger value. In the range over 1.0 in velocity ratio
where big thrust can be generated, spring type had more than twice of
propulsive efficiency increase compared to the prototype.
Abstract: The present study was designed to demonstrate the seasonal variations in physico-chemical parameters of fish farm at Govt. Nursery Unit, Muzaffargarh, Department of Fisheries Govt. of Punjab, Pakistan for a period of eight months from January to August 2008. Water samples were collected on fifteen days basis and have been analyzed for estimation of Air temperature, Water temperature, Light penetration, pH, Total dissolved oxygen, Clouds, Carbonates, Bicarbonates, Total carbonates, Total dissolved solids, Chlorides, Calcium and Hardness. Seasonal fluctuations were observed in all the physico-chemical parameters of fish farm. The overall physicochemical parameters of fish pond water remained within the tolerable range throughout the study period.
Abstract: Because of the global warming and the rising sea level, residents living in southwestern coastland, Taiwan are faced with the submerged land and may move to higher elevation area. It is desirable to discuss the key consideration factor for selecting the migration location under five dimensions of ಯ security”, “health”, “convenience”, “comfort” and “socio-economic” based on the document reviews. This paper uses the Structural Equation Modeling (SEM) and the questionnaire survey. The analysis results show that the convenience is the most key factor for residents in Taiwan.
Abstract: In this paper, we present a technical and an economic
assessment of several sources of renewable energy in Saudi Arabia;
mainly solar, wind, hydro and biomass. We analyze the
environmental and climatic conditions in relation to these sources
and give an overview of some of the existing clean energy
technologies. Using standardized cost and efficiency data, we carry
out a cost benefit analysis to understand the economic factors
influencing the sustainability of energy production from renewable
sources in light of the energy cost and demand in the Saudi market.
Finally, we take a look at the Saudi petroleum industry and the
existing sources of conventional energy and assess the potential of
building a successful market for renewable energy under the
constraints imposed by the flow of subsidized cheap oil. We show
that while some renewable energy resources are well suited for
distributed or grid connected generation in the kingdom, their
viability is greatly undercut by the well developed and well
capitalized oil industry.
Abstract: This study experimentally and numerically investigates
motor cooling performance. The motor consists of a centrifugal fan,
two axial fans, a shaft, a stator, a rotor and a heat exchanger with 637
cooling tubes. The pressure rise-flow rate (P-Q) performance curves of
the cooling fans at 1800 rpm are tested using a test apparatus
complying with the Chinese National Standard (CNS) 2726.
Compared with the experimental measurements, the numerical
analysis results show that the P-Q performance curves of the axial fan
and centrifugal fan can be estimated within about 2% and 6%,
respectively. By using the simplified model, setting up the heat
exchanger and stator as porous media, the flow field in the motor is
calculated. By using the results of the flow field near the rotor and
stator, and subjecting the heat generation rate as a boundary condition,
the temperature distributions of the stator and rotor are also calculated.
The simulation results show that the calculated temperature of the
stator winding near the axial fans is lower by about 5% than the
measured value, and the calculated temperature of the stator core
located at the center of the stator is about 1% higher than the measured
value. Besides, discussion is made to improve the motor cooling
performance.
Abstract: Using 1km grid datasets representing monthly mean
precipitation, monthly mean temperature, and dry matter production
(DMP), we considered the regional plant production ability in
Southeast and South Asia, and also employed pixel-by-pixel
correlation analysis to assess the intensity of relation between climate
factors and plant production. While annual DMP in South Asia was
approximately less than 2,000kg, the one in most part of Southeast
Asia exceeded 2,500 - 3,000kg. It suggested that plant production in
Southeast Asia was superior to South Asia, however, Rain-Use
Efficiency (RUE) representing dry matter production per 1mm
precipitation showed that inland of Indochina Peninsula and India
were higher than islands in Southeast Asia. By the results of
correlation analysis between climate factors and DMP, while the area
in most parts of Indochina Peninsula indicated negative correlation
coefficients between DMP and precipitation or temperature, the area
in Malay Peninsula and islands showed negative correlation to
precipitation and positive one to temperature, and most part of India
dominating South Asia showed positive to precipitation and negative
to temperature. In addition, the areas where the correlation coefficients
exceeded |0.8| were regarded as “susceptible" to climate factors, and
the areas smaller than |0.2| were “insusceptible". By following the
discrimination, the map implying expected impacts by climate change
was provided.
Abstract: Voice over Internet Protocol (VoIP) application or commonly known as softphone has been developing an increasingly large market in today-s telecommunication world and the trend is expected to continue with the enhancement of additional features. This includes leveraging on the existing presence services, location and contextual information to enable more ubiquitous and seamless communications. In this paper, we discuss the concept of seamless session transfer for real-time application such as VoIP and IPTV, and our prototype implementation of such concept on a selected open source VoIP application. The first part of this paper is about conducting performance evaluation and assessments across some commonly found open source VoIP applications that are Ekiga, Kphone, Linphone and Twinkle so as to identify one of them for implementing our design of seamless session transfer. Subjective testing has been carried out to evaluate the audio performance on these VoIP applications and rank them according to their Mean Opinion Score (MOS) results. The second part of this paper is to discuss on the performance evaluations of our prototype implementation of session transfer using Linphone.
Abstract: This paper gives an introduction to Web mining, then
describes Web Structure mining in detail, and explores the data
structure used by the Web. This paper also explores different Page
Rank algorithms and compare those algorithms used for Information
Retrieval. In Web Mining, the basics of Web mining and the Web
mining categories are explained. Different Page Rank based
algorithms like PageRank (PR), WPR (Weighted PageRank), HITS
(Hyperlink-Induced Topic Search), DistanceRank and DirichletRank
algorithms are discussed and compared. PageRanks are calculated for
PageRank and Weighted PageRank algorithms for a given hyperlink
structure. Simulation Program is developed for PageRank algorithm
because PageRank is the only ranking algorithm implemented in the
search engine (Google). The outputs are shown in a table and chart
format.