Abstract: This paper presents the theoretical investigation of a
slotted patch antenna. The main objective of proposed work is to
obtain a large bandwidth antenna with reduced size. The antenna has
a compact size of 21.1mm x 20.25mm x 8.5mm. Two designs with
minor variation are studied which provide wide impedance
bandwidths of 24.056% and 25.63% respectively with the use of
parasitic elements when excited by a probe feed. The advantages of
this configuration are its compact size and the wide range of
frequencies covered. A parametric study is also conducted to
investigate the characteristics of the antenna under different
conditions. The measured return loss and radiation pattern indicate
the suitability of this design for WLAN applications, namely, Wi-
Max, 802.11a/b/g and ISM bands.
Abstract: This study experimentally and numerically investigates
motor cooling performance. The motor consists of a centrifugal fan,
two axial fans, a shaft, a stator, a rotor and a heat exchanger with 637
cooling tubes. The pressure rise-flow rate (P-Q) performance curves of
the cooling fans at 1800 rpm are tested using a test apparatus
complying with the Chinese National Standard (CNS) 2726.
Compared with the experimental measurements, the numerical
analysis results show that the P-Q performance curves of the axial fan
and centrifugal fan can be estimated within about 2% and 6%,
respectively. By using the simplified model, setting up the heat
exchanger and stator as porous media, the flow field in the motor is
calculated. By using the results of the flow field near the rotor and
stator, and subjecting the heat generation rate as a boundary condition,
the temperature distributions of the stator and rotor are also calculated.
The simulation results show that the calculated temperature of the
stator winding near the axial fans is lower by about 5% than the
measured value, and the calculated temperature of the stator core
located at the center of the stator is about 1% higher than the measured
value. Besides, discussion is made to improve the motor cooling
performance.
Abstract: This paper gives an introduction to Web mining, then
describes Web Structure mining in detail, and explores the data
structure used by the Web. This paper also explores different Page
Rank algorithms and compare those algorithms used for Information
Retrieval. In Web Mining, the basics of Web mining and the Web
mining categories are explained. Different Page Rank based
algorithms like PageRank (PR), WPR (Weighted PageRank), HITS
(Hyperlink-Induced Topic Search), DistanceRank and DirichletRank
algorithms are discussed and compared. PageRanks are calculated for
PageRank and Weighted PageRank algorithms for a given hyperlink
structure. Simulation Program is developed for PageRank algorithm
because PageRank is the only ranking algorithm implemented in the
search engine (Google). The outputs are shown in a table and chart
format.
Abstract: In this paper, we present a robust and secure
algorithm for watermarking, the watermark is first transformed into
the frequency domain using the discrete wavelet transform (DWT).
Then the entire DWT coefficient except the LL (Band) discarded,
these coefficients are permuted and encrypted by specific mixing.
The encrypted coefficients are inserted into the most significant
spectral components of the stego-image using a chaotic system. This
technique makes our watermark non-vulnerable to the attack (like
compression, and geometric distortion) of an active intruder, or due
to noise in the transmission link.
Abstract: In this paper, in order to categorize ORL database face
pictures, principle Component Analysis (PCA) and Kernel Principal
Component Analysis (KPCA) methods by using Elman neural
network and Support Vector Machine (SVM) categorization methods
are used. Elman network as a recurrent neural network is proposed
for modeling storage systems and also it is used for reviewing the
effect of using PCA numbers on system categorization precision rate
and database pictures categorization time. Categorization stages are
conducted with various components numbers and the obtained results
of both Elman neural network categorization and support vector
machine are compared. In optimum manner 97.41% recognition
accuracy is obtained.
Abstract: The demand on High voltage (HV) infrastructures is growing due to the corresponding growth in industries and population. Many areas are being developed and therefore require additional electrical power to comply with the demand. Substation upgrade is one of the rapid solutions to ensure the continuous supply of power to customers. This upgrade requires civil modifications to structures and fences. The civil work requires excavation and steel works that may create unsafe touch conditions. This paper presents a brief theoretical overview of the touch voltage inside and around substations and uses CDEGS software to simulate a case study.
Abstract: Almost all Libyan industries (both private and public) have struggled with many difficulties during the past three decades due to many problems. These problems have created a strongly negative impact on the productivity and utilization of many companies within Libya. This paper studies the current awareness and implementation levels of Just-In-Time (JIT) within the Libyan Textile private industry. A survey has been applied in this study using an intensive detailed questionnaire. Based on the analysis of the survey responses, the results show that the management body within the surveyed companies has a modest strategy towards most of the areas that are considered as being very crucial in any successful implementation of JIT. The results also show a variation within the implementation levels of the JIT elements as these varies between Low and Acceptable levels. The paper has also identified limitations within the investigated areas within this industry, and has pointed to areas where senior managers within the Libyan textile industry should take immediate actions in order to achieve effective implementation of JIT within their companies.
Abstract: In this paper, a framework for the simplification and
standardization of metaheuristic related parameter-tuning by applying
a four phase methodology, utilizing Design of Experiments and
Artificial Neural Networks, is presented. Metaheuristics are multipurpose
problem solvers that are utilized on computational optimization
problems for which no efficient problem specific algorithm
exist. Their successful application to concrete problems requires the
finding of a good initial parameter setting, which is a tedious and
time consuming task. Recent research reveals the lack of approach
when it comes to this so called parameter-tuning process. In the
majority of publications, researchers do have a weak motivation for
their respective choices, if any. Because initial parameter settings
have a significant impact on the solutions quality, this course of
action could lead to suboptimal experimental results, and thereby
a fraudulent basis for the drawing of conclusions.
Abstract: Food borne illnesses have been reported to be a global
health challenge. Annual incidences of food–related diseases involve
76 million cases, of which only 14 million can be traced to known
pathogens. Poor hygienic practices have contributed greatly to this. It
has been reported that in the year 2000 about 2.1 million people died
from diarrheal diseases, hence, there is a need to ensure food safety at
all level. This study focused on the sterility examination and
inhibitory effect of honey samples on selected gram negative and
gram positive food borne pathogen from South West Nigeria. The
laboratory examinations revealed the presence of some bacterial and
fungal contaminations of honey samples and that inhibitory activity
of the honey sample was more pronounced on the gram negative
bacteria than the gram positive bacterial isolates. Antibiotic
sensitivity test conducted on the different bacterial isolates also
showed that honey was able to inhibit the proliferation of the tested
bacteria than the employed antibiotics.
Abstract: We proposed a technique to identify road traffic
congestion levels from velocity of mobile sensors with high accuracy
and consistent with motorists- judgments. The data collection utilized
a GPS device, a webcam, and an opinion survey. Human perceptions
were used to rate the traffic congestion levels into three levels: light,
heavy, and jam. Then the ratings and velocity were fed into a
decision tree learning model (J48). We successfully extracted vehicle
movement patterns to feed into the learning model using a sliding
windows technique. The parameters capturing the vehicle moving
patterns and the windows size were heuristically optimized. The
model achieved accuracy as high as 99.68%. By implementing the
model on the existing traffic report systems, the reports will cover
comprehensive areas. The proposed method can be applied to any
parts of the world.
Abstract: The use of amine mixtures employing
methyldiethanolamine (MDEA), monoethanolamine (MEA), and diethanolamine (DEA) have been investigated for a variety of cases
using a process simulation program called HYSYS. The results show that, at high pressures, amine mixtures have little or no advantage in the cases studied. As the pressure is lowered, it becomes more difficult for MDEA to meet residual gas requirements and mixtures can usually improve plant performance. Since the CO2 reaction rate
with the primary and secondary amines is much faster than with
MDEA, the addition of small amounts of primary or secondary amines to an MDEA based solution should greatly improve the overall reaction rate of CO2 with the amine solution. The addition of MEA caused the CO2 to be absorbed more strongly in the upper portion of the column than for MDEA along. On the other hand,
raising the concentration for MEA to 11%wt, CO2 is almost
completely absorbed in the lower portion of the column. The addition of MEA would be most advantageous.
Thus, in areas where MDEA cannot meet the residual gas
requirements, the use of amine mixtures can usually improve the plant
performance.
Abstract: The structure of retinal vessels is a prominent feature,
that reveals information on the state of disease that are reflected in
the form of measurable abnormalities in thickness and colour.
Vascular structures of retina, for implementation of clinical diabetic
retinopathy decision making system is presented in this paper.
Retinal Vascular structure is with thin blood vessel, whose accuracy
is highly dependent upon the vessel segmentation. In this paper the
blood vessel thickness is automatically detected using preprocessing
techniques and vessel segmentation algorithm. First the capture
image is binarized to get the blood vessel structure clearly, then it is
skeletonised to get the overall structure of all the terminal and
branching nodes of the blood vessels. By identifying the terminal
node and the branching points automatically, the main and branching
blood vessel thickness is estimated. Results are presented and
compared with those provided by clinical classification on 50 vessels
collected from Bejan Singh Eye hospital..
Abstract: In present article the model of Blended Learning, its advantage at foreign language teaching, and also some problems that can arise during its use are considered. The Blended Learning is a special organization of learning, which allows to combine classroom work and modern technologies in electronic distance teaching environment. Nowadays a lot of European educational institutions and companies use such technology. Through this method: student gets the opportunity to learn in a group (classroom) with a teacher and additionally at home at a convenient time; student himself sets the optimal speed and intensity of the learning process; this method helps student to discipline himself and learn to work independently.
Abstract: Data Envelopment Analysis (DEA) is a methodology
that computes efficiency values for decision making units (DMU) in a
given period by comparing the outputs with the inputs. In many cases,
there are some time lag between the consumption of inputs and the
production of outputs. For a long-term research project, it is hard to
avoid the production lead time phenomenon. This time lag effect
should be considered in evaluating the performance of organizations.
This paper suggests a model to calculate efficiency values for the
performance evaluation problem with time lag. In the experimental
part, the proposed methods are compared with the CCR and an
existing time lag model using the data set of the 21st century frontier
R&D program which is a long-term national R&D program of Korea.
Abstract: This paper examined the influence of matching
students- learning preferences with the teaching methodology
adopted, on their academic performance in an accounting course in
two types of learning environment in one university in Lebanon:
classes with PowerPoint (PPT) vs. conventional classes. Learning
preferences were either for PPT or for Conventional methodology. A
statistically significant increase in academic achievement is found in
the conventionally instructed group as compared to the group taught
with PPT. This low effectiveness of PPT might be attributed to the
learning preferences of Lebanese students. In the PPT group, better
academic performance was found among students with
learning/teaching match as compared with students with
learning/teaching mismatch. Since the majority of students display a
preference for the conventional methodology, the result might
suggest that Lebanese students- performance is not optimized by PPT
in the accounting classrooms, not because of PPT itself, but because
it is not matching the Lebanese students- learning preferences in such
a quantitative course.
Abstract: In this paper we investigate the electrical
characteristics of a new structure of gate all around strained silicon
nanowire field effect transistors (FETs) with dual dielectrics by
changing the radius (RSiGe) of silicon-germanium (SiGe) wire and
gate dielectric. Indeed the effect of high-κ dielectric on Field Induced
Barrier Lowering (FIBL) has been studied. Due to the higher electron
mobility in tensile strained silicon, the n-type FETs with strained
silicon channel have better drain current compare with the pure Si
one. In this structure gate dielectric divided in two parts, we have
used high-κ dielectric near the source and low-κ dielectric near the
drain to reduce the short channel effects. By this structure short
channel effects such as FIBL will be reduced indeed by increasing
the RSiGe, ID-VD characteristics will be improved. The leakage
current and transfer characteristics, the threshold-voltage (Vt), the
drain induced barrier height lowering (DIBL), are estimated with
respect to, gate bias (VG), RSiGe and different gate dielectrics. For
short channel effects, such as DIBL, gate all around strained silicon
nanowire FET have similar characteristics with the pure Si one while
dual dielectrics can improve short channel effects in this structure.
Abstract: This paper describes text mining technique for automatically extracting association rules from collections of textual documents. The technique called, Extracting Association Rules from Text (EART). It depends on keyword features for discover association rules amongst keywords labeling the documents. In this work, the EART system ignores the order in which the words occur, but instead focusing on the words and their statistical distributions in documents. The main contributions of the technique are that it integrates XML technology with Information Retrieval scheme (TFIDF) (for keyword/feature selection that automatically selects the most discriminative keywords for use in association rules generation) and use Data Mining technique for association rules discovery. It consists of three phases: Text Preprocessing phase (transformation, filtration, stemming and indexing of the documents), Association Rule Mining (ARM) phase (applying our designed algorithm for Generating Association Rules based on Weighting scheme GARW) and Visualization phase (visualization of results). Experiments applied on WebPages news documents related to the outbreak of the bird flu disease. The extracted association rules contain important features and describe the informative news included in the documents collection. The performance of the EART system compared with another system that uses the Apriori algorithm throughout the execution time and evaluating extracted association rules.
Abstract: This paper presents a Particle Swarm Optimization
(PSO) method for determining the optimal parameters of a first-order
controller for TCP/AQM system. The model TCP/AQM is described
by a second-order system with time delay. First, the analytical
approach, based on the D-decomposition method and Lemma of
Kharitonov, is used to determine the stabilizing regions of a firstorder
controller. Second, the optimal parameters of the controller are
obtained by the PSO algorithm. Finally, the proposed method is
implemented in the Network Simulator NS-2 and compared with the
PI controller.
Abstract: In this paper an algorithm is used to detect the color defects of ceramic tiles. First the image of a normal tile is clustered using GCMA; Genetic C-means Clustering Algorithm; those results in best cluster centers. C-means is a common clustering algorithm which optimizes an objective function, based on a measure between data points and the cluster centers in the data space. Here the objective function describes the mean square error. After finding the best centers, each pixel of the image is assigned to the cluster with closest cluster center. Then, the maximum errors of clusters are computed. For each cluster, max error is the maximum distance between its center and all the pixels which belong to it. After computing errors all the pixels of defected tile image are clustered based on the centers obtained from normal tile image in previous stage. Pixels which their distance from their cluster center is more than the maximum error of that cluster are considered as defected pixels.
Abstract: An important step in studying the statistics of
fingerprint minutia features is to reliably extract minutia features from
the fingerprint images. A new reliable method of computation for
minutiae feature extraction from fingerprint images is presented. A
fingerprint image is treated as a textured image. An orientation flow
field of the ridges is computed for the fingerprint image. To
accurately locate ridges, a new ridge orientation based computation
method is proposed. After ridge segmentation a new method of
computation is proposed for smoothing the ridges. The ridge skeleton
image is obtained and then smoothed using morphological operators
to detect the features. A post processing stage eliminates a large
number of false features from the detected set of minutiae features.
The detected features are observed to be reliable and accurate.