Abstract: Participation in sporting activities can lead to injury.
Sport injuries have been widely studied in many sports including the
more extreme categories of aquatic board sports. Kitesurfing is a
relatively new water surface action sport, and has not yet been
widely studied in terms of injuries and stress on the body. The aim of
this study was to get information about which injuries that are most
common among kitesurfing participants, where they occur, and their
causes. Injuries were studied using an international open web
questionnaire (n=206).
The results showed that many respondents reported injuries, in
total 251 injuries to knee (24%), ankle (17%), trunk (16%) and
shoulders (10%), often sustained while doing jumps and tricks
(40%). Among the reported injuries were joint injuries (n=101),
muscle/tendon damages (n=47), wounds and cuts (n=36) and bone
fractures (n=28). Also environmental factors and equipment can
influence the risk of injury, or the extent of injury in a hazardous
situation. Conclusively, the information from this retrospective study
supports earlier studies in terms of prevalence and site of injuries.
Suggestively, this information should be used for to build a
foundation of knowledge about the sport for development of
applications for physical training and product development.
Abstract: Iterative learning control aims to achieve zero tracking
error of a specific command. This is accomplished by iteratively
adjusting the command given to a feedback control system, based on
the tracking error observed in the previous iteration. One would like
the iterations to converge to zero tracking error in spite of any error
present in the model used to design the learning law. First, this need
for stability robustness is discussed, and then the need for robustness
of the property that the transients are well behaved. Methods of
producing the needed robustness to parameter variations and to
singular perturbations are presented. Then a method involving
reverse time runs is given that lets the world behavior produce the
ILC gains in such a way as to eliminate the need for a mathematical
model. Since the real world is producing the gains, there is no issue
of model error. Provided the world behaves linearly, the approach
gives an ILC law with both stability robustness and good transient
robustness, without the need to generate a model.
Abstract: The aim of the present work is to study the effect of annealing on the vibration damping capacity of high-chromium (16%) ferromagnetic steel. The alloys were prepared from raw materials of 99.9% purity melted in a high frequency induction furnace under high vacuum. The samples were heat-treated in vacuum at various temperatures (800 to 1200ºC) for 1 hour followed by slow cooling (120ºC/h). The inverted torsional pendulum method was used to evaluate the vibration damping capacity. The results indicated that the vibration damping capacity of the alloys is influenced by annealing and there exists a critical annealing temperature after 1000ºC. The damping capacity increases quickly below the critical temperature since the magnetic domains move more easily.
Abstract: The research objective of the project and article “The impact of Structural Funds on the growth of competitiveness of Polish agriculture" is to assess competitiveness of regions in Poland from the perspective of Polish agriculture by analysing the efficiency of the use of Structural Funds, the economic procedure of their distribution and the regulatory and organisational framework under the Rural Development Programme (RDP). It must be stressed that defining the scope of research in the above manner limits the analysis only to the part of Structural Funds directed to support Polish agriculture.
Abstract: A motion protection system is designed for a parallel
motion platform with subsided cabin. Due to its complex structure,
parallel mechanism is easy to encounter interference problems
including link length limits, joints limits and self-collision. Thus a
virtual spring algorithm in operational space is developed for the
motion protection system to avoid potential damages caused by
interference. Simulation results show that the proposed motion
protection system can effectively eliminate interference problems and
ensure safety of the whole motion platform.
Abstract: We propose the use of magneto-optic Kerr effect (MOKE) to realize single-qubit quantum gates. We consider longitudinal and polar MOKE in reflection geometry in which the magnetic field is parallel to both the plane of incidence and surface of the film. MOKE couples incident TE and TM polarized photons and the Hamiltonian that represents this interaction is isomorphic to that of a canonical two-level quantum system. By varying the phase and amplitude of the magnetic field, we can realize Hadamard, NOT, and arbitrary phase-shift single-qubit quantum gates. The principal advantage is operation with magnetically non-transparent materials.
Abstract: Vehicle suspension design must fulfill
some conflicting criteria. Among those is ride comfort
which is attained by minimizing the acceleration
transmitted to the sprung mass, via suspension spring
and damper. Also good handling of a vehicle is a
desirable property which requires stiff suspension and
therefore is in contrast with a vehicle with good ride.
Among the other desirable features of a suspension is
the minimization of the maximum travel of suspension.
This travel which is called suspension working space in
vehicle dynamics literature is also a design constraint
and it favors good ride. In this research a full car 8
degrees of freedom model has been developed and the
three above mentioned criteria, namely: ride, handling
and working space has been adopted as objective
functions. The Multi Objective Programming (MOP)
discipline has been used to find the Pareto Front and
some reasoning used to chose a design point between
these non dominated points of Pareto Front.
Abstract: This study presents a systematic analysis of the
dynamic behaviors of a gear-bearing system with porous squeeze film
damper (PSFD) under nonlinear suspension, nonlinear oil-film force
and nonlinear gear meshing force effect. It can be found that the
system exhibits very rich forms of sub-harmonic and even the chaotic
vibrations. The bifurcation diagrams also reveal that greater values of
permeability may not only improve non-periodic motions effectively,
but also suppress dynamic amplitudes of the system. Therefore, porous
effect plays an important role to improve dynamic stability of
gear-bearing systems or other mechanical systems. The results
presented in this study provide some useful insights into the design
and development of a gear-bearing system for rotating machinery that
operates in highly rotational speed and highly nonlinear regimes.
Abstract: Historical monuments as architectural heritage are,
economically and culturally, considered one of the key aspects for
modern communities. Cultural heritage represents a country-s
national identity and pride and maintains and enriches that country-s
culture. Therefore, conservation of the monuments remained from
our ancestors requires everybody-s serious and unremitting effort.
Conservation, renewal, restoration, and technical study of cultural
and historical matters are issues which have a special status among
various forms of art and science in the present century and this is due
to two reasons: firstly, progress of humankind in this century has
created a factor called environmental pollution which not only has
caused new destructive processes of cultural/historical monuments
but also has accelerated the previous destructive processes by several
times, and secondly, the rapid advance of various sciences, especially
chemistry, has lead to the contribution of new methods and materials
to this significant issue.
Abstract: It is known that the heart interacts with and adapts to
its venous and arterial loading conditions. Various experimental
studies and modeling approaches have been developed to investigate
the underlying mechanisms. This paper presents a model of the left
ventricle derived based on nonlinear stress-length myocardial
characteristics integrated over truncated ellipsoidal geometry, and
second-order dynamic mechanism for the excitation-contraction
coupling system. The results of the model presented here describe the
effects of the viscoelastic damping element of the electromechanical
coupling system on the hemodynamic response. Different heart rates
are considered to study the pacing effects on the performance of the
left-ventricle against constant preload and afterload conditions under
various damping conditions. The results indicate that the pacing
process of the left ventricle has to take into account, among other
things, the viscoelastic damping conditions of the myofilament
excitation-contraction process.
Abstract: Research on damage of gears and gear pairs using
vibration signals remains very attractive, because vibration signals
from a gear pair are complex in nature and not easy to interpret.
Predicting gear pair defects by analyzing changes in vibration signal
of gears pairs in operation is a very reliable method. Therefore, a
suitable vibration signal processing technique is necessary to extract
defect information generally obscured by the noise from dynamic
factors of other gear pairs.This article presents the value of cepstrum
analysis in vehicle gearbox fault diagnosis. Cepstrum represents the
overall power content of a whole family of harmonics and sidebands
when more than one family of sidebands is present at the same time.
The concept for the measurement and analysis involved in using the
technique are briefly outlined. Cepstrum analysis is used for detection
of an artificial pitting defect in a vehicle gearbox loaded with
different speeds and torques. The test stand is equipped with three
dynamometers; the input dynamometer serves asthe internal
combustion engine, the output dynamometers introduce the load on
the flanges of the output joint shafts. The pitting defect is
manufactured on the tooth side of a gear of the fifth speed on the
secondary shaft. Also, a method for fault diagnosis of gear faults is
presented based on order Cepstrum. The procedure is illustrated with
the experimental vibration data of the vehicle gearbox. The results
show the effectiveness of Cepstrum analysis in detection and
diagnosis of the gear condition.
Abstract: The incidence of mechanical fracture of an
automobile piston rings prompted development of fracture analysis
method on this case. The three rings (two compression rings and one
oil ring) were smashed into several parts during the power-test (after
manufacturing the engine) causing piston and liner to be damaged.
The radial and oblique cracking happened on the failed piston rings.
The aim of the fracture mechanics simulations presented in this paper
was the calculation of particular effective fracture mechanics
parameters, such as J-integrals and stress intensity factors. Crack
propagation angles were calculated as well. Two-dimensional
fracture analysis of the first compression ring has been developed in
this paper using ABAQUS CAE6.5-1 software. Moreover, SEM
fractography was developed on fracture surfaces and is discussed in
this paper. Results of numerical calculations constitute the basis for
further research on real object.
Abstract: It is quite essential to form dialogue mechanisms and
dialogue channels to solve intercultural communication issues.
Therefore, every country should develop a intercultural education
project which aims to resolve international communication issues.
For proper mediation training, the first step is to reach an agreement
on the actors to run the project. The strongest mediation mechanisms
in the world should be analyzed and initiated within the educational
policies. A communication-based mediation model should be
developed for international mediation training. Mediators can use
their convincing communication skills as a part of this model. At the
first, fundamental stages of the mediation training should be specified
within the scope of the model. Another important topic at this point is
common sence and peace leaders to act as an ombudsman in this
process. Especially for solving some social issues and conflicts,
common sense leaders acting as an ombudsman would lead to
effective communication. In mediation training that is run by
universities and non-governmental organizations, another phase is to
focus on conducting the meetings. In intercultural mediation training,
one of the most critical topics is to conduct the meeting traffic and
performing a shuttle diplomacy. Meeting traffic is where the mediator
organizes meetings with the parties with initiative powers, in order to
contribute to the solution of the issue, and schedule these meetings.
In this notice titled “ Intercultural mediation training and the training
process of common sense leaders by the leadership of universities
communication and artistic campaigns" , communication models and
strategies about this topic will be constructed and an intercultural art
activities and perspectives will be presented.
Abstract: Intelligent technologies are increasingly facilitating
sustainable water management strategies in Australia. While this
innovation can present clear cost benefits to utilities through
immediate leak detection and deference of capital costs, the impact of
this technology on households is less distinct. By offering real-time
engagement and detailed end-use consumption breakdowns, there is
significant potential for demand reduction as a behavioural response
to increased information. Despite this potential, passive
implementation without well-planned residential engagement
strategies is likely to result in a lost opportunity. This paper begins
this research process by exploring the effect of smart water meters
through the lens of three behaviour change theories. The Theory of
Planned Behaviour (TPB), Belief Revision theory (BR) and Practice
Theory emphasise different variables that can potentially influence
and predict household water engagements. In acknowledging the
strengths of each theory, the nuances and complexity of household
water engagement can be recognised which can contribute to
effective planning for residential smart meter engagement strategies.
Abstract: There are lots of different ways to find the natural
frequencies of a rotating system. One of the most effective methods
which is used because of its precision and correctness is the
application of the transfer matrix. By use of this method the entire
continuous system is subdivided and the corresponding differential
equation can be stated in matrix form. So to analyze shaft that is this
paper issue the rotor is divided as several elements along the shaft
which each one has its own mass and moment of inertia, which this
work would create possibility of defining the named matrix. By
Choosing more elements number, the size of matrix would become
larger and as a result more accurate answers would be earned. In this
paper the dynamics of a rotor-bearing system is analyzed,
considering the gyroscopic effect. To increase the accuracy of
modeling the thickness of the disk and bearings is also taken into
account which would cause more complicated matrix to be solved.
Entering these parameters to our modeling would change the results
completely that these differences are shown in the results. As said
upper, to define transfer matrix to reach the natural frequencies of
probed system, introducing some elements would be one of the
requirements. For the boundary condition of these elements, bearings
at the end of the shaft are modeled as equivalent spring and dampers
for the discretized system. Also, continuous model is used for the
shaft in the system. By above considerations and using transfer
matrix, exact results are taken from the calculations. Results Show
that, by increasing thickness of the bearing the amplitude of vibration
would decrease, but obviously the stiffness of the shaft and the
natural frequencies of the system would accompany growth.
Consequently it is easily understood that ignoring the influences of
bearing and disk thicknesses would results not real answers.
Abstract: In 1990 [1] the subband-DFT (SB-DFT) technique was proposed. This technique used the Hadamard filters in the decomposition step to split the input sequence into low- and highpass sequences. In the next step, either two DFTs are needed on both bands to compute the full-band DFT or one DFT on one of the two bands to compute an approximate DFT. A combination network with correction factors was to be applied after the DFTs. Another approach was proposed in 1997 [2] for using a special discrete wavelet transform (DWT) to compute the discrete Fourier transform (DFT). In the first step of the algorithm, the input sequence is decomposed in a similar manner to the SB-DFT into two sequences using wavelet decomposition with Haar filters. The second step is to perform DFTs on both bands to obtain the full-band DFT or to obtain a fast approximate DFT by implementing pruning at both input and output sides. In this paper, the wavelet-based DFT (W-DFT) with Haar filters is interpreted as SB-DFT with Hadamard filters. The only difference is in a constant factor in the combination network. This result is very important to complete the analysis of the W-DFT, since all the results concerning the accuracy and approximation errors in the SB-DFT are applicable. An application example in spectral analysis is given for both SB-DFT and W-DFT (with different filters). The adaptive capability of the SB-DFT is included in the W-DFT algorithm to select the band of most energy as the band to be computed. Finally, the W-DFT is extended to the two-dimensional case. An application in image transformation is given using two different types of wavelet filters.
Abstract: Nowadays, the performance required for concrete
structures is more complicated and diversified. Self-compacting
concrete is a fluid mixture suitable for placing in structures with
congested reinforcement without vibration. Self-compacting concrete
development must ensure a good balance between deformability and
stability. Also, compatibility is affected by the characteristics of
materials and the mix proportions; it becomes necessary to evolve a
procedure for mix design of SCC.
This paper presents an experimental procedure for the design of
self-compacting concrete mixes with different water-cement ratios
(w/c) and other constant ratios by local materials. The test results for
acceptance characteristics of self-compacting concrete such as slump
flow, V-funnel and L-Box are presented. Further, compressive
strength, tensile strength and modulus of elasticity of specimens were
also determined and results are included here
Abstract: Currently, there is no database or local norms for the
physical performance of Malaysian rugby players. This database or
norms are vital for Malaysian-s sports development as programs can
be setup to improve the current status. This pilot study was
conducted to evaluate the status of our semi professional rugby
players. The rugby players were randomly selected from the
Malaysian National team and several clubs in the Klang valley, Kuala
Lumpur Malaysia. 54 male rugby players (Age: 24.41 ± 4.06 years)
were selected for this pilot study. Height, bodyweight, percentage
body fat and body mass index (BMI) and several other physical tests
were performed. Results from the BLEEP test revealed an average of
level 9, shuttle 2 for the players. Interestingly, forwards were taller,
heavier, and had lower maximal aerobic power than backs in the
same team. In conclusion, the physical characteristics of the rugby
players were much lower when compared to international players
from other countries. From this pilot study, the physical performance
of the Malaysian team must be improved in order to further develop
the sports.
Abstract: Properly sized capacitor banks are connected across induction motors for several reasons including power factor correction, reducing distortions, increasing capacity, etc. Total harmonic distortion (THD) and power factor (PF) are used in such cases to quantify the improvements obtained through connection of the external capacitor banks. On the other hand, one of the methods for assessing the motor internal condition is by the use of Park-s pattern analysis. In spite of taking adequate precautionary measures, the capacitor banks may sometimes malfunction. Such a minor fault in the capacitor bank is often not apparently discernible. This may however, give rise to substantial degradation of power factor correction performance and may also damage the supply profile. The case is more severe with the fact that the Park-s pattern gets distorted due to such external capacitor faults, and can give anomalous results about motor internal fault analyses. The aim of this paper is to present simulation and hardware laboratory test results to have an understanding of the anomalies in harmonic distortion and Park-s pattern analyses in induction motors due to capacitor bank defects.
Abstract: We introduce a new interactive 3D simulator of ocular motion and expressions suitable for: (1) character animation applications to game design, film production, HCI (Human Computer Interface), conversational animated agents, and virtual reality; (2) medical applications (ophthalmic neurological and muscular pathologies: research and education); and (3) real time simulation of unconscious cognitive and emotional responses (for use, e.g., in psychological research). Using state-of-the-art computer animation technology we have modeled and rigged a physiologically accurate 3D model of the eyes, eyelids, and eyebrow regions and we have 'optimized' it for use with an interactive and web deliverable platform. In addition, we have realized a prototype device for realtime control of eye motions and expressions, including unconsciously produced expressions, for application as in (1), (2), and (3) above. The 3D simulator of eye motion and ocular expression is, to our knowledge, the most advanced/realistic available so far for applications in character animation and medical pedagogy.