Abstract: Low gear noise is an important sound quality feature in modern passenger cars. Annoying gear noise from the gearbox is influenced by the gear design, gearbox shaft layout, manufacturing deviations in the components, assembly errors and the mounting arrangement of the complete gearbox. Geometrical deviations in the form of profile and lead errors are often present on the flanks of the inspected gears. Ghost frequencies of a gear are very challenging to identify in standard gear measurement and analysis process due to small wavelengths involved. In this paper, gear whine noise occurring at non-integral multiples of gear mesh frequency of passenger car gearbox is investigated and the root cause is identified using the displacement deviation analysis (DDA) method. DDA method is applied to identify ghost frequency excitations on the flanks of gears arising out of generation grinding. Frequency identified through DDA correlated with the frequency of vibration and noise on the end-of-line machine as well as vehicle level measurements. With the application of DDA method along with standard lead profile measurement, gears with ghost frequency geometry deviations were identified on the production line to eliminate defective parts and thereby eliminate ghost frequency noise from a vehicle. Further, displacement deviation analysis can be used in conjunction with the manufacturing process simulation to arrive at suitable countermeasures for arresting the ghost frequency.
Abstract: This paper presents modeling and control strategy for the grid connected wind turbine system based on Permanent Magnet Synchronous Generator (PMSG). The considered system is based on back-to-back converter topology. The Grid Side Converter (GSC) achieves the DC bus voltage control and unity power factor. The Machine Side Converter (MSC) assures the PMSG speed control. The PMSG is used as a variable speed generator and connected directly to the turbine without gearbox. The pitch angle control is not either considered in this study. Further, Optimal Tip Speed Ratio (OTSR) based MPPT control strategy is used to ensure the most energy efficiency whatever the wind speed variations. A filter (L) is put between the GSC and the grid to reduce current ripple and to improve the injected power quality. The proposed grid connected wind system is built under MATLAB/Simulink environment. The simulation results show the feasibility of the proposed topology and performance of its control strategies.
Abstract: In more complex systems, such as automotive
gearbox, a rigorous treatment of the data is necessary because there
are several moving parts (gears, bearings, shafts, etc.), and in this
way, there are several possible sources of errors and also noise. The
basic objective of this work is the detection of damage in automotive
gearbox. The detection methods used are the wavelet method, the
bispectrum; advanced filtering techniques (selective filtering) of
vibrational signals and mathematical morphology. Gearbox vibration
tests were performed (gearboxes in good condition and with defects)
of a production line of a large vehicle assembler. The vibration
signals are obtained using five accelerometers in different positions
of the sample. The results obtained using the kurtosis, bispectrum,
wavelet and mathematical morphology showed that it is possible to
identify the existence of defects in automotive gearboxes.
Abstract: In this paper, some common gearboxes vibration analysis methods and condition monitoring systems are explained. In addition, an experimental gearbox vibration analysis is discussed through a critical case history for a mixer gearbox related to Iran oil industry. The case history also consists of gear manufacturing (machining) recommendations, lubrication condition of gearbox and machinery maintenance activities that caused reduction in noise and vibration of the gearbox. Besides some of the recent patents and innovations in gearboxes, lubrication and vibration monitoring systems explained. Finally micro pitting and surface fatigue in pinion and bevel of mentioned horizontal to vertical gearbox discussed in details.
Abstract: Research on damage of gears and gear pairs using
vibration signals remains very attractive, because vibration signals
from a gear pair are complex in nature and not easy to interpret.
Predicting gear pair defects by analyzing changes in vibration signal
of gears pairs in operation is a very reliable method. Therefore, a
suitable vibration signal processing technique is necessary to extract
defect information generally obscured by the noise from dynamic
factors of other gear pairs.This article presents the value of cepstrum
analysis in vehicle gearbox fault diagnosis. Cepstrum represents the
overall power content of a whole family of harmonics and sidebands
when more than one family of sidebands is present at the same time.
The concept for the measurement and analysis involved in using the
technique are briefly outlined. Cepstrum analysis is used for detection
of an artificial pitting defect in a vehicle gearbox loaded with
different speeds and torques. The test stand is equipped with three
dynamometers; the input dynamometer serves asthe internal
combustion engine, the output dynamometers introduce the load on
the flanges of the output joint shafts. The pitting defect is
manufactured on the tooth side of a gear of the fifth speed on the
secondary shaft. Also, a method for fault diagnosis of gear faults is
presented based on order Cepstrum. The procedure is illustrated with
the experimental vibration data of the vehicle gearbox. The results
show the effectiveness of Cepstrum analysis in detection and
diagnosis of the gear condition.
Abstract: This paper presents modern vibration signalprocessing
techniques for vehicle gearbox fault diagnosis, via the
wavelet analysis and the Squared Envelope (SE) technique. The
wavelet analysis is regarded as a powerful tool for the detection of
sudden changes in non-stationary signals. The Squared Envelope
(SE) technique has been extensively used for rolling bearing
diagnostics. In the present work a scheme of using the Squared
Envelope technique for early detection of gear tooth pit. The pitting
defect is manufactured on the tooth side of a fifth speed gear on the
intermediate shaft of a vehicle gearbox. The objective is to
supplement the current techniques of gearbox fault diagnosis based
on using the raw vibration and ordered signals. The test stand is
equipped with three dynamometers; the input dynamometer serves as
the internal combustion engine, the output dynamometers introduce
the load on the flanges of output joint shafts. The gearbox used for
experimental measurements is the type most commonly used in
modern small to mid-sized passenger cars with transversely mounted
powertrain and front wheel drive; a five-speed gearbox with final
drive gear and front wheel differential. The results show that the
approaches methods are effective for detecting and diagnosing
localized gear faults in early stage under different operation
conditions, and are more sensitive and robust than current gear
diagnostic techniques.
Abstract: This work presents a numerical model developed to
simulate the dynamics and vibrations of a multistage tractor gearbox.
The effect of time varying mesh stiffness, time varying frictional
torque on the gear teeth, lateral and torsional flexibility of the shafts
and flexibility of the bearings were included in the model. The model
was developed by using the Lagrangian method, and it was applied to
study the effect of three design variables on the vibration and stress
levels on the gears. The first design variable, module, had little effect
on the vibration levels but a higher module resulted to higher bending
stress levels. The second design variable, pressure angle, had little
effect on the vibration levels, but had a strong effect on the stress
levels on the pinion of a high reduction ratio gear pair. A pressure
angle of 25o resulted to lower stress levels for a pinion with 14 teeth
than a pressure angle of 20o. The third design variable, contact ratio,
had a very strong effect on both the vibration levels and bending
stress levels. Increasing the contact ratio to 2.0 reduced both the
vibration levels and bending stress levels significantly. For the gear
train design used in this study, a module of 2.5 and contact ratio of
2.0 for the various meshes was found to yield the best combination
of low vibration levels and low bending stresses. The model can
therefore be used as a tool for obtaining the optimum gear design
parameters for a given multistage spur gear train.