Abstract: In this study, the effects and interactions of reaction
time and capping agent assistance during sol-gel synthesis of
magnesium substituted hydroxyapatite nanopowder (MgHA) on
hydroxyapatite (HA) to β-tricalcium phosphate (β-TCP) ratio, Ca/P
ratio and mean crystallite size was examined experimentally as well
as through statistical analysis. MgHA nanopowders were synthesized
by sol-gel technique at room temperature using aqueous solution of
calcium nitrate tetrahydrate, magnesium nitrate hexahydrate and
potassium dihydrogen phosphate as starting materials. The reaction
time for sol-gel synthesis was varied between 15 to 60 minutes. Two
process routes were followed with and without addition of
triethanolamine (TEA) in the solutions. The elemental compositions
of as-synthesized powders were determined using X-ray fluorescence
(XRF) spectroscopy. The functional groups present in the assynthesized
MgHA nanopowders were established through Fourier
Transform Infrared Spectroscopy (FTIR). The amounts of phases
present, Ca/P ratio and mean crystallite sizes of MgHA nanopowders
were determined using X-ray diffraction (XRD). The HA content in
biphasic mixture of HA and β-TCP and Ca/P ratio in as-synthesized
MgHA nanopowders increased effectively with reaction time of sols
(p0.15, two way ANOVA). The MgHA nanopowders
synthesized with TEA assistance exhibited 14 nm lower crystallite
size (p
Abstract: This study evaluated the acute toxicity and tissue
distribution of intravenously administered gold nanoparticles
(AuNPs) in male rabbits. Rabbits were exposed to single dose of
AuNPs (300 μg/ kg). Toxic effects were assessed via general
behavior, hematological parameters, serum biochemical parameters,
and histopathological examination of various rabbits’ organs.
Inductively coupled plasma–mass spectrometry (ICP-MS) was used
to determine gold concentrations in tissue samples collected at
predetermined time intervals. After one week, AuNPs exerted no
obvious acute toxicity in rabbits. However, inflammatory reactions
were observed in liver, lungs and kidneys accompanied with mild
absolute neutrophilia and significant monocytosis. The highest gold
levels were found in the spleen and liver followed by lungs, and
kidneys. These results indicated that AuNPs could be distributed
extensively to various tissues in the body, but primarily in the spleen
and liver.
Abstract: The purposes of this research are to make comparisons in
respect of the behaviors on the use of the services of metered taxi
classified by the demographic factor and to study the influence of the
recognition on service quality having the effect on usage behaviors of
metered taxi services of consumers in Bangkok Metropolitan Areas. The
samples used in this research were 400 metered taxi service users in
Bangkok Metropolitan Areas and questionnaire was used as the tool for
collecting the data. Analysis statistics are mean and multiple regression
analysis. Results of the research revealed that the consumers recognize the
overall quality of services in each aspect include tangible aspects of the
service, responses to customers, assurance on the confidence,
understanding and knowing of customers which is rated at the moderate
level except the aspect of the assurance on the confidence and
trustworthiness which are rated at a high level. For the result of
hypothetical test, it is found that the quality in providing the services on
the aspect of the assurance given to the customers has the effect on the
usage behaviors of metered taxi services and the aspect of the frequency
on the use of the services per month which in this connection. Such
variable can forecast at one point nine percent (1.9%). In addition, quality
in providing the services and the aspect of the responses to customers
have the effect on the behaviors on the use of metered taxi services on the
aspect of the expenses on the use of services per month which in this
connection, such variable can forecast at two point one percent (2.1%).
Abstract: The end panels of a large rectangular industrial duct,
which experience significant internal pressures, also experience
considerable transverse shear due to transfer of gravity loads to the
supports. The current design practice of such thin plate panels for
shear load is based on methods used for the design of plate girder
webs. The structural arrangements, the loadings and the resulting
behavior associated with the industrial duct end panels are, however,
significantly different from those of the web of a plate girder. The
large aspect ratio of the end panels gives rise to multiple bands of
tension fields, whereas the plate girder web design is based on one
tension field. In addition to shear, the industrial end panels are
subjected to internal pressure which in turn produces significant
membrane action. This paper reports a study which was undertaken
to review the current industrial analysis and design methods and to
propose a comprehensive method of designing industrial duct end
panels for shear resistance. In this investigation, a nonlinear finite element model was
developed to simulate the behavior of industrial duct end panel, along
with the associated edge stiffeners, subjected to transverse shear and
internal pressures. The model considered the geometric imperfections
and constitutive relations for steels. Six scale independent
dimensionless parameters that govern the behavior of such end panel
were identified and were then used in a parametric study. It was
concluded that the plate slenderness dominates the shear strength of
stockier end panels, and whereas, both the plate slenderness and the
aspect ratio influence the shear strength of slender end panels. Based
on these studies, this paper proposes design aids for estimating the
shear strength of rectangular duct end panels.
Abstract: In this work, our goal is to optimize the nitriding treatment at a low-temperature of the steel 32CrMoV13 using gas mixtures of ammonia, nitrogen and hydrogen to improve the mechanical properties of the surface (good wear resistance, friction and corrosion), and of the diffusion layer of the nitrogen (good resistance to fatigue and good tenacity with heart). By limiting our work to the pure iron and to the alloys iron-chromium and iron-chromium-carbon, we have studied the various parameters which manage the nitriding: flow rate and composition of the gaseous phase, the interaction chromium-nitrogen and chromium-carbon by the help of experiments of nitriding realized in the laboratory by thermogravimetry. The acquired knowledge has been applied by the mastery of the growth of the γ' combination layer on the α diffusion layer in the case of the industrial steel 32CrMoV13.
Abstract: A three-dimensional numerical simulation of flow
through mini and microchannels with designed roughness is
conducted here. The effect of the roughness height (surface
roughness), geometry, Reynolds number on the friction factor, and
Nusselt number is investigated. The study is carried out by
employing CFD software, CFX. Our work focuses on a water flow
inside a circular mini-channel of 1 mm and microchannels of 500 and
100 m in diameter. The speed entry varies from 0.1 m/s to 20 m/s.
The general trend can be observed that bigger sizes of roughness
element lead to higher flow resistance. It is found that the friction
factor increases in a nonlinear fashion with the increase in obstruction
height. Particularly, the effect of roughness can no longer be ignored
at relative roughness height higher than 3%. A significant increase in
Poiseuille number is detected for all configurations considered. The
same observation can be done for Nusselt number. The transition
zone between laminar and turbulent flow depends on the channel
diameter.
Abstract: We regard forecasting of energy consumption by
private production areas of a large industrial facility as well as by the
facility itself. As for production areas, the forecast is made based on
empirical dependencies of the specific energy consumption and the
production output. As for the facility itself, implementation of the
task to minimize the energy consumption forecasting error is based
on adjustment of the facility’s actual energy consumption values
evaluated with the metering device and the total design energy
consumption of separate production areas of the facility. The
suggested procedure of optimal energy consumption was tested based
on the actual data of core product output and energy consumption by
a group of workshops and power plants of the large iron and steel
facility. Test results show that implementation of this procedure gives
the mean accuracy of energy consumption forecasting for winter
2014 of 0.11% for the group of workshops and 0.137% for the power
plants.
Abstract: Gladiolus is an important cash crop and is grown
mainly for its elegant spikes. Traditionally the gladiolus corms are
planted manually which is very tedious, time consuming and labor
intensive operation. So far, there is no planter available for planting
of gladiolus corms. With a view to mechanize the planting operation
of this horticultural crop, a prototype of 4-row gladiolus planter was
developed and its performance was evaluated in-situ condition. Cupchain
type metering device was used to place each single gladiolus
corm in furrow at required spacing while planting. Three levels of
corm spacing viz 15, 20 and 25 cm and four levels of forward speed
viz 1.0, 1.5, 2.0 and 2.5 km/h was taken as evaluation parameter for
the planter. The performance indicators namely corm spacing in each
row, coefficient of uniformity, missing index, multiple index, quality
of feed index, number of corms per meter length, mechanical damage
to the corms etc. were determined during the field test. The data was
statistically analyzed using Completely Randomized Design (CRD)
for testing the significance of the parameters. The result indicated
that planter was able to drop the corms at required nominal spacing
with minor variations. The highest deviation from the mean corm
spacing was observed as 3.53 cm with maximum coefficient of
variation as 13.88%. The highest missing and quality of feed indexes
were observed as 6.33% and 97.45% respectively with no multiples.
The performance of the planter was observed better at lower forward
speed and wider corm spacing. The field capacity of the planter was
found as 0.103 ha/h with an observed field efficiency of 76.57%.
Abstract: In this paper, approach to incoherent signal detection
in multi-element antenna array are researched and modeled. Two
types of useful signals with unknown wavefront were considered:
first one, deterministic (Barker code), and second one, random
(Gaussian distribution). The derivation of the sufficient statistics took
into account the linearity of the antenna array. The performance
characteristics and detecting curves are modeled and compared for
different useful signals parameters and for different number of
elements of the antenna array. Results of researches in case of some
additional conditions can be applied to a digital communications
systems.
Abstract: We present probabilistic multinomial Dirichlet
classification model for multidimensional data and Gaussian process
priors. Here, we have considered efficient computational method that
can be used to obtain the approximate posteriors for latent variables
and parameters needed to define the multiclass Gaussian process
classification model. We first investigated the process of inducing a
posterior distribution for various parameters and latent function by
using the variational Bayesian approximations and important sampling
method, and next we derived a predictive distribution of latent
function needed to classify new samples. The proposed model is
applied to classify the synthetic multivariate dataset in order to verify
the performance of our model. Experiment result shows that our model
is more accurate than the other approximation methods.
Abstract: Production fluids are transported from the platform to
tankers or process facilities through transfer pipelines. Water being
one of the heavier phases tends to settle at the bottom of pipelines
especially at low flow velocities and this has adverse consequences
for pipeline integrity. On restart after a shutdown, this could result in
corrosion and issues for process equipment, thus the need to have the
heavier liquid dispersed into the flowing lighter fluid. This study
looked at the flow regime of low water cut and low flow velocity oil
and water flow using conductive film thickness probes in a large
diameter 4-inch pipe to obtain oil and water interface height and the
interface structural velocity. A wide range of 0.1–1.0 m/s oil and
water mixture velocities was investigated for 0.5–5% water cut. Two
fluid model predictions were used to compare with the experimental
results.
Abstract: This research work presents the surface
thermodynamics approach to M-TB/HIV-Human sputum
interactions. This involved the use of the Hamaker coefficient
concept as a surface energetics tool in determining the interaction
processes, with the surface interfacial energies explained using van
der Waals concept of particle interactions. The Lifshitz derivation for
van der Waals forces was applied as an alternative to the contact
angle approach which has been widely used in other biological
systems. The methodology involved taking sputum samples from
twenty infected persons and from twenty uninfected persons for
absorbance measurement using a digital Ultraviolet visible
Spectrophotometer. The variables required for the computations with
the Lifshitz formula were derived from the absorbance data. The
Matlab software tools were used in the mathematical analysis of the
data produced from the experiments (absorbance values). The
Hamaker constants and the combined Hamaker coefficients were
obtained using the values of the dielectric constant together with the
Lifshitz Equation. The absolute combined Hamaker coefficients
A132abs and A131abs on both infected and uninfected sputum samples
gave the values of A132abs = 0.21631x10-21Joule for M-TB infected
sputum and Ã132abs = 0.18825x10-21Joule for M-TB/HIV infected
sputum. The significance of this result is the positive value of the
absolute combined Hamaker coefficient which suggests the existence
of net positive van der waals forces demonstrating an attraction
between the bacteria and the macrophage. This however, implies that
infection can occur. It was also shown that in the presence of HIV,
the interaction energy is reduced by 13% conforming adverse effects
observed in HIV patients suffering from tuberculosis.
Abstract: This study aims to examine the sensory quality of
meatballs made from Balinese beef and buffalo meat after the
addition of smoke powder prior to storage at the temperatures of 2-
5°C for 7 days. This study used meat from Longissimus dorsi muscle
of male Balinese cattle aged 3 years and of male buffalo aged 5 years
as the main raw materials, and smoke powder as a binder and
preservative in making meatballs. The study was based on completely
randomized design (CRD) of factorial pattern of 2 x 3 x 2 where
factors 1, 2 and 3 included the types of meat (cattle and buffalo),
types of smoke powder (oven dried, freeze dried and spray dried)
with a level of 2% of the weight of the meat (w/w), and storage
duration (0 and 7 days) with three replications, respectively. The
parameters measured were the meatball sensory quality (scores of
tenderness, firmness, chewing residue, and intensity of flavor). The
results of this study show that each type of meat has produced
different sensory characteristics. The meatballs made from buffalo
meat have higher tenderness and elasticity scores than the Balinese
beef. Meanwhile, the buffalo meatballs have a lower residue
mastication score than the Balinese beef. Each type of smoke
powders has produced a relatively similar sensory quality of
meatballs. It can be concluded that the smoke powder of 2% of the
weight of the meat (w/w) could maintain the sensory quality of the
meatballs for 7 days of storage.
Abstract: Finding the optimal 3D path of an aerial vehicle under
flight mechanics constraints is a major challenge, especially when
the algorithm has to produce real time results in flight. Kinematics
models and Pythagorian Hodograph curves have been widely used
in mobile robotics to solve this problematic. The level of difficulty
is mainly driven by the number of constraints to be saturated at the
same time while minimizing the total length of the path. In this paper,
we suggest a pragmatic algorithm capable of saturating at the same
time most of dimensioning helicopter 3D trajectories’ constraints
like: curvature, curvature derivative, torsion, torsion derivative, climb
angle, climb angle derivative, positions. The trajectories generation
algorithm is able to generate versatile complex 3D motion primitives
feasible by a helicopter with parameterization of the curvature and the
climb angle. An upper ”motion primitives’ concatenation” algorithm
is presented based. In this article we introduce a new way of designing
three-dimensional trajectories based on what we call the ”Dubins
gliding symmetry conjecture”. This extremely performing algorithm
will be soon integrated to a real-time decisional system dealing with
inflight safety issues.
Abstract: Geological and tectonic framework indicates that
Bangladesh is one of the most seismically active regions in the world.
The Bengal Basin is at the junction of three major interacting plates:
the Indian, Eurasian, and Burma Plates. Besides there are many
active faults within the region, e.g. the large Dauki fault in the north.
The country has experienced a number of destructive earthquakes due
to the movement of these active faults. Current seismic provisions of
Bangladesh are mostly based on earthquake data prior to the 1990.
Given the record of earthquakes post 1990, there is a need to revisit
the design provisions of the code. This paper compares the base shear
demand of three major cities in Bangladesh: Dhaka (the capital city),
Sylhet, and Chittagong for earthquake scenarios of magnitudes
7.0MW, 7.5MW, 8.0MW, and 8.5MW using a stochastic model. In
particular, the stochastic model allows the flexibility to input region
specific parameters such as shear wave velocity profile (that were
developed from Global Crustal Model CRUST2.0) and include the
effects of attenuation as individual components. Effects of soil
amplification were analysed using the Extended Component
Attenuation Model (ECAM). Results show that the estimated base
shear demand is higher in comparison with code provisions leading to
the suggestion of additional seismic design consideration in the study
regions.
Abstract: The understanding of geotechnical characteristics of
near-surface material and the effects of the groundwater is very
important problem in such as site studies. For showing the relations
between seismic data and groundwater, we selected about 25 km2 as
the study area. It has been presented which is a detailed work of
seismic data and groundwater depths of Gokpinar Damp area.
Seismic waves velocity (Vp and Vs) are very important parameters
showing the soil properties. The seismic records were used the
method of the multichannel analysis of surface waves near area of
Gokpinar Damp area. Sixty sites in this area have been investigated
with survey lines about 60 m in length. MASW (Multichannel
analysis of surface wave) method has been used to generate onedimensional
shear wave velocity profile at locations. These shear
wave velocities are used to estimate equivalent shear wave velocity in
the study area at every 2 and 5 m intervals up to a depth of 45 m.
Levels of equivalent shear wave velocity of soil are used the
classified of the study area. After the results of the study, it must be
considered as components of urban planning and building design of
Gokpinar Damp area, Denizli and the application and use of these
results should be required and enforced by municipal authorities.
Abstract: In this paper, the 2-D unsteady viscous flow around
two cam shaped cylinders in tandem arrangement is numerically
simulated in order to study the characteristics of the flow in turbulent
regimes. The investigation covers the effects of high subcritical and
supercritical Reynolds numbers and L/D ratio on total drag
coefficient. The equivalent diameter of cylinders is 27.6 mm The
space between center to center of two cam shaped cylinders is define
as longitudinal pitch ratio and it varies in range of 1.5< L/D
Abstract: In this paper, we propose the variational EM inference
algorithm for the multi-class Gaussian process classification model
that can be used in the field of human behavior recognition. This
algorithm can drive simultaneously both a posterior distribution of a
latent function and estimators of hyper-parameters in a Gaussian
process classification model with multiclass. Our algorithm is based
on the Laplace approximation (LA) technique and variational EM
framework. This is performed in two steps: called expectation and
maximization steps. First, in the expectation step, using the Bayesian
formula and LA technique, we derive approximately the posterior
distribution of the latent function indicating the possibility that each
observation belongs to a certain class in the Gaussian process
classification model. Second, in the maximization step, using a derived
posterior distribution of latent function, we compute the maximum
likelihood estimator for hyper-parameters of a covariance matrix
necessary to define prior distribution for latent function. These two
steps iteratively repeat until a convergence condition satisfies.
Moreover, we apply the proposed algorithm with human action
classification problem using a public database, namely, the KTH
human action data set. Experimental results reveal that the proposed
algorithm shows good performance on this data set.
Abstract: The Com-Poisson (CMP) model is one of the most
popular discrete generalized linear models (GLMS) that handles
both equi-, over- and under-dispersed data. In longitudinal context,
an integer-valued autoregressive (INAR(1)) process that incorporates
covariate specification has been developed to model longitudinal
CMP counts. However, the joint likelihood CMP function is
difficult to specify and thus restricts the likelihood-based estimating
methodology. The joint generalized quasi-likelihood approach
(GQL-I) was instead considered but is rather computationally
intensive and may not even estimate the regression effects due
to a complex and frequently ill-conditioned covariance structure.
This paper proposes a new GQL approach for estimating the
regression parameters (GQL-III) that is based on a single score vector
representation. The performance of GQL-III is compared with GQL-I
and separate marginal GQLs (GQL-II) through some simulation
experiments and is proved to yield equally efficient estimates as
GQL-I and is far more computationally stable.
Abstract: Background: Breast milk may impact early brain
development, with potentially important biological, medical and
social implications. There is an important discussion on which is the
adequate breastfeeding extension to the development consolidation
and how the children breastfeeding affects their psychomotor
development, in the first year of life, and in following periods as
well. Some special fats (LC PUFA) contained in breast milk play a
key role in the brain’s maturation and cognitive development or
social skills. These capacities created during breastfeeding time
would be unfolded throughout all lifespan. Aim of the study: In our research, we have studied the effect of
breastfeeding in preschooler's psychomotor assessment.
Method: This study was conducted in a sample of 158 preschool
children in Vlorë, Albania. We have measured the psychometric
parameters of preschoolers with ASQ-3 (Age&Stage Questionnaires-
3). The studied sample was divided in three groups according to their
breastfeeding duration (3, 6 and 12 months). Results: Children breastfed for only 3 months have definitely
lower psychometric scores compared to the ones with 6 or more
months of breastfeeding (respectively 217 to 239 ASQ-3 scores). Six
and twelvemonth breastfed children have progressively more odds to
have high levels of psychomotor development comparing to those
with only 3 months of breastfeeding. The most affected psychometric
domains by shortness of breastfeeding are Communication and
Global motor. Conclusion: This leads to conclusion that to ensure high
psychomotor parameters during childhood is necessary breastfeeding
for at least 6 months.