Abstract: The use of machine vision to inspect the outcome of
surgical tasks is investigated, with the aim of incorporating this
approach in robotic surgery systems. Machine vision is a non-contact
form of inspection i.e. no part of the vision system is in direct contact
with the patient, and is therefore well suited for surgery where
sterility is an important consideration,. As a proof-of-concept, three
primary surgical tasks for a common neurosurgical procedure were
inspected using machine vision. Experiments were performed on
cadaveric pig heads to simulate the two possible outcomes i.e.
satisfactory or unsatisfactory, for tasks involved in making a burr
hole, namely incision, retraction, and drilling. We identify low level
image features to distinguish the two outcomes, as well as report on
results that validate our proposed approach. The potential of using
machine vision in a surgical environment, and the challenges that
must be addressed, are identified and discussed.
Abstract: This work presents the results of a study carried out to
determine the sliding wear behavior and its effect on the process
parameters of components manufactured by direct metal laser
sintering (DMLS). A standard procedure and specimen had been used
in the present study to find the wear behavior. Using Taguchi-s
experimental technique, an orthogonal array of modified L8 had been
developed. Sliding wear testing using pin-on-disk machine was
carried out and analysis of variance (ANOVA) technique was used to
investigate the effect of process parameters and to identify the main
process parameter that influences the properties of wear behavior on
the DMLS components. It has been found that part orientation, one
of the selected process parameter had more influence on wear as
compared to other selected process parameters.
Abstract: In this paper, investigation of subsynchronous
resonance (SSR) characteristics of a hybrid series compensated
system and the design of voltage controller for three level 24-pulse
Voltage Source Converter based Static Synchronous Series
Compensator (SSSC) is presented. Hybrid compensation consists of
series fixed capacitor and SSSC which is a active series FACTS
controller. The design of voltage controller for SSSC is based on
damping torque analysis, and Genetic Algorithm (GA) is adopted for
tuning the controller parameters. The SSR Characteristics of SSSC
with constant reactive voltage control modes has been investigated.
The results show that the constant reactive voltage control of SSSC
has the effect of reducing the electrical resonance frequency, which
detunes the SSR.The analysis of SSR with SSSC is carried out based
on frequency domain method, eigenvalue analysis and transient
simulation. While the eigenvalue and damping torque analysis are
based on D-Q model of SSSC, the transient simulation considers both
D-Q and detailed three phase nonlinear system model using
switching functions.
Abstract: One of the main concerns in the Information Technology field is adoption with new technologies in organizations which may result in increasing the usage paste of these technologies.This study aims to look at the issue of culture-s role in accepting and using new technologies in organizations. The study examines the effect of culture on accepting and intention to use new technology in organizations. Studies show culture is one of the most important barriers in adoption new technologies. The model used for accepting and using new technology is Technology Acceptance Model (TAM), while for culture and dimensions a well-known theory by Hofsted was used. Results of the study show significant effect of culture on intention to use new technologies. All four dimensions of culture were tested to find the strength of relationship with behavioral intention to use new technologies. Findings indicate the important role of culture in the level of intention to use new technologies and different role of each dimension to improve adaptation process. The study suggests that transferring of new technologies efforts are most likely to be successful if the parties are culturally aligned.
Abstract: An ethnobotanical study was conducted to document
local knowledge and potentials of wild edible tubers that has been
reported and sighted and to investigate and record their distribution in
Pulau Redang and nearby islands of Terengganu, Malaysia.
Information was gathered from 42 villagers by using semi-structured
questionnaire. These respondents were selected randomly and no
appointment was made prior to the visits. For distribution, the
locations of wild edible tubers were recorded by using the Global
Positioning System (GPS). The wild edible tubers recorded were ubi
gadung, ubi toyo, ubi kasu, ubi jaga, ubi seratus and ubi kertas.
Dioscorea or commonly known as yam is reported to be one of the
major food sources worldwide. The majority of villagers used
Dioscorea hispida Dennst. or ubi gadung in many ways in their life
such as for food, medicinal purposes and fish poison. The villagers
have identified this ubi gadung by looking at the morphological
characteristics; that include leaf shape, stem and the color of the
tuber-s flesh.
Abstract: Business process management (BPM) has become
widely accepted within business community as a means for
improving business performance. However, it is of the highest
importance to incorporate BPM as part of the curriculum at the
university level education in order to achieve the appropriate
acceptance of the method. Goal of the paper is to determine the
current state of education in business process management (BPM) at
the Croatian universities and abroad. It investigates the applied forms
of instruction and teaching methods and gives several proposals for
BPM courses improvement. Since majority of undergraduate and
postgraduate students have limited understanding of business
processes and lack of any practical experience, there is a need for
introducing new teaching approaches. Therefore, we offer some
suggestions for further improvement, among which the introduction
of simulation games environment in BPM education is strongly
recommended.
Abstract: Toughening of polyamide 6 (PA6)/ Nanoclay (NC) nanocomposites with styrene-ethylene/butadiene-styrene copolymer (SEBS) using maleated styrene-ethylene/butadiene-styrene copolymer (mSEBS)/ as a compatibilizer were investigated by blending them in a co-rotating twin-screw extruder. Response surface method of experimental design was used for optimizing the material and processing parameters. Effect of four factors, including SEBS, mSEBS and NC contents as material variables and order of mixing as a processing factor, on toughness of hybrid nanocomposites were studied. All the prepared samples showed ductile behavior and low temperature Izod impact toughness of some of the hybrid nanocomposites demonstrated 900% improvement compared to the PA6 matrix while the modulus showed maximum enhancement of 20% compared to the pristine PA6 resin.
Abstract: Knowing consumers' preferences and perceptions of
the sensory evaluation of drink products are very significant to
manufacturers and retailers alike. With no appropriate sensory
analysis, there is a high risk of market disappointment. This paper
aims to rank the selected coffee products and also to determine the
best of quality attribute through sensory evaluation using fuzzy
decision making model. Three products of coffee drinks were used
for sensory evaluation. Data were collected from thirty judges at a
hypermarket in Kuala Terengganu, Malaysia. The judges were asked
to specify their sensory evaluation in linguistic terms of the quality
attributes of colour, smell, taste and mouth feel for each product and
also the weight of each quality attribute. Five fuzzy linguistic terms
represent the quality attributes were introduced prior analysing. The
judgment membership function and the weights were compared to
rank the products and also to determine the best quality attribute. The
product of Indoc was judged as the first in ranking and 'taste' as the
best quality attribute. These implicate the importance of sensory
evaluation in identifying consumers- preferences and also the
competency of fuzzy approach in decision making.
Abstract: Advent enhancements in the field of computing have
increased massive use of web based electronic documents. Current
Copyright protection laws are inadequate to prove the ownership for
electronic documents and do not provide strong features against
copying and manipulating information from the web. This has
opened many channels for securing information and significant
evolutions have been made in the area of information security.
Digital Watermarking has developed into a very dynamic area of
research and has addressed challenging issues for digital content.
Watermarking can be visible (logos or signatures) and invisible
(encoding and decoding). Many visible watermarking techniques
have been studied for text documents but there are very few for web
based text. XML files are used to trade information on the internet
and contain important information. In this paper, two invisible
watermarking techniques using Synonyms and Acronyms are
proposed for XML files to prove the intellectual ownership and to
achieve the security. Analysis is made for different attacks and
amount of capacity to be embedded in the XML file is also noticed.
A comparative analysis for capacity is also made for both methods.
The system has been implemented using C# language and all tests are
made practically to get the results.
Abstract: One major source of performance decline in speaker
recognition system is channel mismatch between training and testing.
This paper focuses on improving channel robustness of speaker
recognition system in two aspects of channel compensation technique
and channel robust features. The system is text-independent speaker
identification system based on two-stage recognition. In the aspect of
channel compensation technique, this paper applies MAP (Maximum
A Posterior Probability) channel compensation technique, which was
used in speech recognition, to speaker recognition system. In the
aspect of channel robust features, this paper introduces
pitch-dependent features and pitch-dependent speaker model for the
second stage recognition. Based on the first stage recognition to
testing speech using GMM (Gaussian Mixture Model), the system
uses GMM scores to decide if it needs to be recognized again. If it
needs to, the system selects a few speakers from all of the speakers
who participate in the first stage recognition for the second stage
recognition. For each selected speaker, the system obtains 3
pitch-dependent results from his pitch-dependent speaker model, and
then uses ANN (Artificial Neural Network) to unite the 3
pitch-dependent results and 1 GMM score for getting a fused result.
The system makes the second stage recognition based on these fused
results. The experiments show that the correct rate of two-stage
recognition system based on MAP channel compensation technique
and pitch-dependent features is 41.7% better than the baseline system
for closed-set test.
Abstract: Prestressing in structure increases ratio of load-bearing capacity to weight. Suspendomes are single-layer braced domes reinforced with cable and strut. Prestressing of cables alter value and distribution of stress in structure. In this study two configuration, diamatic and lamella domes is selected. Investigated domes have span of 100m with rise-to-span ratios of 0.1, 0.2, and 0.3. Single layer domes loaded under service load combinations according to ISO code. After geometric nonlinear analysis, models are designed with tubular and I-shaped sections then reinforced with cable and strut and converted to suspendomes. Displacements and stresses of some groups of nodes and elements in all of single-layer domes and suspendomes for three load combinations, symmetric snow, asymmetric snow and wind are compared. Variation due to suspending system is investigated. Suspendomes are redesigned and minimum possible weight after addition of cable and strut is obtained.
Abstract: Subjective loneliness describes people who feel a
disagreeable or unacceptable lack of meaningful social relationships,
both at the quantitative and qualitative level. The studies to be
presented tested an Italian 18-items self-report loneliness measure,
that included items adapted from scales previously developed,
namely a short version of the UCLA (Russell, Peplau and Cutrona,
1980), and the 11-items Loneliness scale by De Jong-Gierveld &
Kamphuis (JGLS; 1985). The studies aimed at testing the developed
scale and at verifying whether loneliness is better conceptualized as a
unidimensional (so-called 'general loneliness') or a bidimensional
construct, namely comprising the distinct facets of social and
emotional loneliness. The loneliness questionnaire included 2 singleitem
criterion measures of sad mood, and social contact, and asked
participants to supply information on a number of socio-demographic
variables. Factorial analyses of responses obtained in two
preliminary studies, with 59 and 143 Italian participants respectively,
showed good factor loadings and subscale reliability and confirmed
that perceived loneliness has clearly two components, a social and an
emotional one, the latter measured by two subscales, a 7-item
'general' loneliness subscale derived from UCLA, and a 6–item
'emotional' scale included in the JGLS. Results further showed that
type and amount of loneliness are related, negatively, to frequency of
social contacts, and, positively, to sad mood. In a third study data
were obtained from a nation-wide sample of 9.097 Italian subjects,
12 to about 70 year-olds, who filled the test on-line, on the Italian
web site of a large-audience magazine, Focus. The results again
confirmed the reliability of the component subscales, namely social,
emotional, and 'general' loneliness, and showed that they were
highly correlated with each other, especially the latter two.
Loneliness scores were significantly predicted by sex, age, education
level, sad mood and social contact, and, less so, by other variables –
e.g., geographical area and profession. The scale validity was
confirmed by the results of a fourth study, with elderly men and
women (N 105) living at home or in residential care units. The three
subscales were significantly related, among others, to depression, and
to various measures of the extension of, and satisfaction with, social
contacts with relatives and friends. Finally, a fifth study with 315
career-starters showed that social and emotional loneliness correlate
with life satisfaction, and with measures of emotional intelligence.
Altogether the results showed a good validity and reliability in the
tested samples of the entire scale, and of its components.
Abstract: The purpose of planned islanding is to construct a
power island during system disturbances which are commonly
formed for maintenance purpose. However, in most of the cases
island mode operation is not allowed. Therefore distributed
generators (DGs) must sense the unplanned disconnection from the
main grid. Passive technique is the most commonly used method for
this purpose. However, it needs improvement in order to identify the
islanding condition. In this paper an effective method for
identification of islanding condition based on phase space and neural
network techniques has been developed. The captured voltage
waveforms at the coupling points of DGs are processed to extract the
required features. For this purposed a method known as the phase
space techniques is used. Based on extracted features, two neural
network configuration namely radial basis function and probabilistic
neural networks are trained to recognize the waveform class.
According to the test result, the investigated technique can provide
satisfactory identification of the islanding condition in the
distribution system.
Abstract: The purpose of this research is to disentangle and
validate the underlying factorial-structure of Ecotourism Experiential
Value (EEV) measurement scale and subsequently investigate its
psychometric properties. The analysis was based on a sample of 225
eco-tourists, collected at the vicinity of Taman Negara National Park
(TNNP) via interviewer-administered questionnaire. Exploratory
factor analysis (EFA) was performed to determine the factorial
structure of EEV. Subsequently, to confirm and validate the factorial
structure and assess the psychometric properties of EEV,
confirmatory factor analysis (CFA) was executed. In addition, to
establish the nomological validity of EEV a structural model was
developed to examine the effect of EEV on Total Eco-tourist
Experience Quality (TEEQ). It is unveiled that EEV is a secondorder
six-factorial structure construct and it scale has adequately met
the psychometric criteria, thus could permit interpretation of results
confidently. The findings have important implications for future
research directions and management of ecotourism destination.
Abstract: The objective is to fabricate organic light emitting
diode and to study its degradation process in atmosphere condition in
which PFO as an emitting material and PEDOT:PSS as a hole
injecting material were used on ITO substrate. Thus degradation
process of the OLED was studied upon its current-voltage
characteristic. By fabricating this OLED and obtaining blue light and
analysis of current-voltage characteristic during the time after
fabrication, it was observed that the current of the OLED was
exponentially decreased. Current reduction during the initial hours of
fabrication was outstanding and after few days its reduction rate was
dropped significantly, while the diode was dying.
Abstract: In this paper, some brief sufficient conditions for the stability of FO-LTI systems dαx(t) dtα = Ax(t) with the fractional order are investigated when the matrix A and the fractional order α are uncertain or both α and A are uncertain, respectively. In addition, we also relate the stability of a fractional-order system with order 0 < α ≤ 1 to the stability of its equivalent fractional-order system with order 1 ≤ β < 2, the relationship between α and β is presented. Finally, a numeric experiment is given to demonstrate the effectiveness of our results.
Abstract: From an economic standpoint the current and future
road traffic situation in urban areas is a cost factor. Traffic jams and
congestion prolong journey times and tie up resources in trucks and
personnel. Many discussions about imposing charges or tolls for
cities in Europe in order to reduce traffic congestion are currently in
progress. Both of these effects lead – directly or indirectly - to
additional costs for the urban distribution systems in retail
companies. One approach towards improving the efficiency of retail
distribution systems, and thus towards avoiding negative
environmental factors in urban areas, is horizontal collaboration for
deliveries to retail outlets – Urban Retail Logistics. This paper
presents a classification system to help reveal where cooperation
between retail companies is possible and makes sense for deliveries
to retail outlets in urban areas.
Abstract: Arguments on a popular microblogging site were analysed by means of a methodological approach to business rhetoric focusing on the logos communication technique. The focus of the analysis was the 100 day countdown to the 2011 Rugby World Cup as advanced by the organisers. Big sporting events provide an attractive medium for sport event marketers in that they have become important strategic communication tools directed at sport consumers. Sport event marketing is understood in the sense of using a microblogging site as a communication tool whose purpose it is to disseminate a company-s marketing messages by involving the target audience in experiential activities. Sport creates a universal language in that it excites and increases the spread of information by word of mouth and other means. The findings highlight the limitations of a microblogging site in terms of marketing messages which can assist in better practices. This study can also serve as a heuristic tool for other researchers analysing sports marketing messages in social network environments.
Abstract: In this paper, a delayed prototype model is studied. Regarding the delay as a bifurcation parameter, we prove that a sequence of Hopf bifurcations will occur at the positive equilibrium when the delay increases. Using the normal form method and center manifold theory, some explicit formulae are worked out for determining the stability and the direction of the bifurcated periodic solutions. Finally, Computer simulations are carried out to explain some mathematical conclusions.
Abstract: Economic crime (i.e. corporate fraud) has a
significant impact on business. This study analyzes the fraud cases
reported by the Malaysian Securities Commission. Frauds involving
market manipulation and/or illegal share trading are the most
common types of fraud reported over the 6 years analyzed. The
highest number of frauds reported involved investment and fund
holding companies. Alarmingly the results indicate quite a high
number of frauds cases are committed by management. The higher
number of Chinese perpetrators may be due to fact that they are the
dominant group in Malaysian business. The result also shows that
more than half of companies involved with fraud are privately held
companies in the investment/fund/finance sector. The results of this
study highlight general characteristic of perpetrators (person and
company) that commit fraud which could help the regulators in their
monitoring and enforcement activities. To investors, this would help
in analyzing their business investment or portfolio risk.