Abstract: In this paper comparison of Reflector Antenna
analyzing techniques based on wave and ray nature of optics is
presented for an offset reflector antenna using GRASP (General
Reflector antenna Analysis Software Package) software. The results
obtained using PO (Physical Optics), PTD (Physical theory of
Diffraction), and GTD (Geometrical Theory of Diffraction) are
compared. The validity of PO and GTD techniques in regions around
the antenna, caustic behavior of GTD in main beam, and deviation of
GTD in case of near-in sidelobes of radiation pattern are discussed.
The comparison for far-out sidelobes predicted by PO, PO + PTD
and GTD is described. The effect of Direct Radiations from feed
which results in feed selection for the system is addressed.
Abstract: We present an Electronic Nose (ENose), which is
aimed at identifying the presence of one out of two gases, possibly
detecting the presence of a mixture of the two. Estimation of the
concentrations of the components is also performed for a volatile
organic compound (VOC) constituted by methanol and acetone, for
the ranges 40-400 and 22-220 ppm (parts-per-million), respectively.
Our system contains 8 sensors, 5 of them being gas sensors (of the
class TGS from FIGARO USA, INC., whose sensing element is a tin
dioxide (SnO2) semiconductor), the remaining being a temperature
sensor (LM35 from National Semiconductor Corporation), a
humidity sensor (HIH–3610 from Honeywell), and a pressure sensor
(XFAM from Fujikura Ltd.).
Our integrated hardware–software system uses some machine
learning principles and least square regression principle to identify at
first a new gas sample, or a mixture, and then to estimate the
concentrations. In particular we adopt a training model using the
Support Vector Machine (SVM) approach with linear kernel to teach
the system how discriminate among different gases. Then we apply
another training model using the least square regression, to predict
the concentrations.
The experimental results demonstrate that the proposed
multiclassification and regression scheme is effective in the
identification of the tested VOCs of methanol and acetone with
96.61% correctness. The concentration prediction is obtained with
0.979 and 0.964 correlation coefficient for the predicted versus real
concentrations of methanol and acetone, respectively.
Abstract: In medical therapy, laser has been widely used to conduct cosmetic, tumor and other treatments. During the process of laser irradiation, there may be thermal damage caused by excessive laser exposure. Thus, the establishment of a complete thermal analysis model is clinically helpful to physicians in reference data. In this study, porcine liver in place of tissue was subjected to laser irradiation to set up the experimental data considering the explored impact on surface thermal field and thermal damage region under different conditions of power, laser irradiation time, and distance between laser and porcine liver. In the experimental process, the surface temperature distribution of the porcine lever was measured by the infrared thermal imager. In the part of simulation, the bio heat transfer Pennes-s equation was solved by software SYSWELD applying in welding process. The double ellipsoid function as a laser source term is firstly considered in the prediction for surface thermal field and internal tissue damage. The simulation results are compared with the experimental data to validate the mathematical model established here in.
Abstract: This article deals with the numerical simulation of the
floor heating convector in 3D. Presented convector can operate in
two modes – cooling mode and heating mode. This initial numerical
simulation is focused on cooling mode of the convector. Models with
different temperature of the fins are compared and three various
shapes of the fins are examined as well. The objective of the work is
to predict air flow and heat transfer inside convector for further
optimalization of these devices. For the numerical simulation was
used commercial software Ansys Fluent.
Abstract: Fuzzy logic approach is used in this study to predict
the tractive performance in terms of traction force, and motion
resistance for an intelligent air cushion track vehicle while it operates
in the swamp peat. The system is effective to control the intelligent
air –cushion system with measuring the vehicle traction force (TF),
motion resistance (MR), cushion clearance height (CH) and cushion
pressure (CP). Sinkage measuring sensor, magnetic switch, pressure
sensor, micro controller, control valves and battery are incorporated
with the Fuzzy logic system (FLS) to investigate experimentally the
TF, MR, CH, and CP. In this study, a comparison for tractive
performance of an intelligent air cushion track vehicle has been
performed with the results obtained from the predicted values of FLS
and experimental actual values. The mean relative error of actual and
predicted values from the FLS model on traction force, and total
motion resistance are found as 5.58 %, and 6.78 % respectively. For
all parameters, the relative error of predicted values are found to be
less than the acceptable limits. The goodness of fit of the prediction
values from the FLS model on TF, and MR are found as 0.90, and
0.98 respectively.
Abstract: Aggression is a multi- factorial concept and multilevel
in nature. The Young Adolescent is being influenced by family,
school and community. This paper is aimed to determine the
following: aggression level among young adolescents, difference of
level of aggression on school and year levels and to determine the
correlates of aggression. There were 142 high school students from
two different national highs schools (Region 3 and National Capital
Region).Convenience sampling was use in this study. The following
measures were used namely: Aggression Scale, Parental Support
Fighting Scale, Positive Behavior Scale and Exposure to Violence
and Trauma questionnaire. There was no significant difference in
aggression level among different year level and schools. The
findings of the study suggested that high level of community violence
and having low parental support for non-aggressive behavior
contribute to the prediction of aggression.
Abstract: SVM ( Support Vector Machine ) is a new method in the artificial neural network ( ANN ). In the steel making, how to use computer to predict the end point of BOF accuracy is a great problem. A lot of method and theory have been claimed, but most of the results is not satisfied. Now the hot topic in the BOF end point predicting is to use optical way the predict the end point in the BOF. And we found that there exist some regular in the characteristic curve of the flame from the mouse of pudding. And we can use SVM to predict end point of the BOF, just single spectrum intensity should be required as the input parameter. Moreover, its compatibility for the input space is better than the BP network.
Abstract: An alternative approach to the use of Discrete Fourier
Transform (DFT) for Magnetic Resonance Imaging (MRI) reconstruction
is the use of parametric modeling technique. This method
is suitable for problems in which the image can be modeled by
explicit known source functions with a few adjustable parameters.
Despite the success reported in the use of modeling technique as an
alternative MRI reconstruction technique, two important problems
constitutes challenges to the applicability of this method, these are
estimation of Model order and model coefficient determination. In
this paper, five of the suggested method of evaluating the model
order have been evaluated, these are: The Final Prediction Error
(FPE), Akaike Information Criterion (AIC), Residual Variance (RV),
Minimum Description Length (MDL) and Hannan and Quinn (HNQ)
criterion. These criteria were evaluated on MRI data sets based on the
method of Transient Error Reconstruction Algorithm (TERA). The
result for each criterion is compared to result obtained by the use of a
fixed order technique and three measures of similarity were evaluated.
Result obtained shows that the use of MDL gives the highest measure
of similarity to that use by a fixed order technique.
Abstract: Inspired by the recent experiments [1]-[3] indicating
unusual doubly magic nucleus 24O which lies just at the neutron
drip-line and encouraged by the success of our relativistic mean-field
(RMF) plus state dependent BCS approach for the description of
the ground state properties of the drip-line nuclei [23]-[27], we have
further employed this approach, across the entire periodic table, to
explore the unusual shell closures in exotic nuclei. In our RMF+BCS
approach the single particle continuum corresponding to the RMF is
replaced by a set of discrete positive energy states for the calculations
of pairing energy. Detailed analysis of the single particle spectrum,
pairing energies and densities of the nuclei predict the unusual proton
shell closures at Z = 6, 14, 16, 34, and unusual neutron shell closures
at N = 6, 14, 16, 34, 40, 70, 112.
Abstract: Electricity market activities and a growing demand for electricity have led to heavily stressed power systems. This requires operation of the networks closer to their stability limits. Power system operation is affected by stability related problems, leading to unpredictable system behavior. Voltage stability refers to the ability of a power system to sustain appropriate voltage levels through large and small disturbances. Steady-state voltage stability is concerned with limits on the existence of steady-state operating points for the network. FACTS devices can be utilized to increase the transmission capacity, the stability margin and dynamic behavior or serve to ensure improved power quality. Their main capabilities are reactive power compensation, voltage control and power flow control. Among the FACTS controllers, Static Var Compensator (SVC) provides fast acting dynamic reactive compensation for voltage support during contingency events. In this paper, voltage stability assessment with appropriate representations of tap-changer transformers and SVC is investigated. Integrating both of these devices is the main topic of this paper. Effect of the presence of tap-changing transformers on static VAR compensator controller parameters and ratings necessary to stabilize load voltages at certain values are highlighted. The interrelation between transformer off nominal tap ratios and the SVC controller gains and droop slopes and the SVC rating are found. P-V curves are constructed to calculate loadability margins.
Abstract: An HPLC-UV analytical method was developed to
determine ethylenediaminetetraacetic acid (EDTA) in dairy
wastewater and surface water. The optimizing separation was achieved
by reversed–phase ion-pair liquid chromatography on a C18 column
using methanol as mobile phase solvent, tetrabutylammonium bromide
as the ion-pair reagent in pH 3.3 formate buffer solution at a flow rate
of 0.9 mL min-1 with a UV detector at 265 nm. No interference of Ca,
Mg or NO3
- was detected. Method performance was evaluated in terms
of linearity, repeatability and reproducibility. The method detection
limit was 5 μg L-1. The contents of EDTA in dairy effluents were 72 ~
261 μg L-1 at a large dairy site. A change of EDTA concentration was
observed downstream of the dairy effluent discharge, but this was well
under the predicted no effect concentration for aquatic ecosystem.
Abstract: We depend upon explanation in order to “make sense"
out of our world. And, making sense is all the more important when
dealing with change. But, what happens if our explanations are
wrong? This question is examined with respect to two types of
explanatory model. Models based on labels and categories we shall
refer to as “representations." More complex models involving
stories, multiple algorithms, rules of thumb, questions, ambiguity we
shall refer to as “compressions." Both compressions and
representations are reductions. But representations are far more
reductive than compressions. Representations can be treated as a set
of defined meanings – coherence with regard to a representation is
the degree of fidelity between the item in question and the definition
of the representation, of the label. By contrast, compressions contain
enough degrees of freedom and ambiguity to allow us to make
internal predictions so that we may determine our potential actions in
the possibility space. Compressions are explanatory via mechanism.
Representations are explanatory via category. Managers are often
confusing their evocation of a representation (category inclusion) as
the creation of a context of compression (description of mechanism).
When this type of explanatory error occurs, more errors follow. In
the drive for efficiency such substitutions are all too often proclaimed
– at the manager-s peril..
Abstract: Colour choice has become a common strategy and
correlates highly with marketing. Three broad functions can be
identified for colour in a building context especially applied in
marketing communications, which are its role as an important
parameter in illumination designs, its capacity to influence the visual
appearance of a building in a predictable manner and as an aesthetic
function. The review of literatures shows that colour has an impact on
online marketing communications, and relations between colour, web
and marketing communications.
Abstract: In this paper back-propagation artificial neural network
(BPANN )with Levenberg–Marquardt algorithm is employed to
predict the deformation of the upsetting process. To prepare a
training set for BPANN, some finite element simulations were
carried out. The input data for the artificial neural network are a set
of parameters generated randomly (aspect ratio d/h, material
properties, temperature and coefficient of friction). The output data
are the coefficient of polynomial that fitted on barreling curves.
Neural network was trained using barreling curves generated by
finite element simulations of the upsetting and the corresponding
material parameters. This technique was tested for three different
specimens and can be successfully employed to predict the
deformation of the upsetting process
Abstract: Trust and Energy consumption is the most challenging
issue in routing protocol design for Mobile ad hoc networks
(MANETs), since mobile nodes are battery powered and nodes
behaviour are unpredictable. Furthermore replacing and recharging
batteries and making nodes co-operative is often impossible in
critical environments like military applications. In this paper, we
propose a trust based energy aware routing model in MANET.
During route discovery, node with more trust and maximum energy
capacity is selected as a router based on a parameter called
'Reliability'. Route request from the source is accepted by a node
only if its reliability is high. Otherwise, the route request is
discarded. This approach forms a reliable route from source to
destination thus increasing network life time, improving energy
utilization and decreasing number of packet loss during transmission.
Abstract: Power systems and transformer are intrinsic apparatus, therefore its reliability and safe operation is important to determine their operation conditions, and the industry uses quality control tests in the insulation design of oil filled transformers. Hence the service period effect on AC dielectric strength is significant. The effect of aging on transformer oil physical, chemical and electrical properties was studied using the international testing methods for the evaluation of transformer oil quality. The study was carried out on six transformers operate in the field and for monitoring periods over twenty years. The properties which are strongly time dependent were specified and those which have a great impact on the transformer oil acidity, breakdown voltage and dissolved gas analysis were defined. Several tests on the transformers oil were studied to know the time of purifying or changing it, moreover prediction of the characteristics of it under different operation conditions.
Abstract: Most of ignition delay correlations studies have been
developed in a constant volume bombs which cannot capture the
dynamic variation in pressure and temperature during the ignition
delay as in real engines. Watson, Assanis et. al. and Hardenberg
and Hase correlations have been developed based on experimental
data of diesel engines. However, they showed limited predictive
ability of ignition delay when compared to experimental results. The
objective of the study was to investigate the dependency of ignition
delay time on engine brake power. An experimental investigation of
the effect of automotive diesel and water diesel emulsion fuels on
ignition delay under steady state conditions of a direct injection diesel
engine was conducted. A four cylinder, direct injection naturally
aspirated diesel engine was used in this experiment over a wide range
of engine speeds and two engine loads. The ignition delay
experimental data were compared with predictions of Assanis et. al.
and Watson ignition delay correlations. The results of the
experimental investigation were then used to develop a new ignition
delay correlation. The newly developed ignition delay correlation has
shown a better agreement with the experimental data than Assanis et.
al. and Watson when using automotive diesel and water diesel
emulsion fuels especially at low to medium engine speeds at both
loads. In addition, the second derivative of cylinder pressure which is
the most widely used method in determining the start of combustion
was investigated.
Abstract: This paper describes the application of a model predictive controller to the problem of batch reactor temperature control. Although a great deal of work has been done to improve reactor throughput using batch sequence control, the control of the actual reactor temperature remains a difficult problem for many operators of these processes. Temperature control is important as many chemical reactions are sensitive to temperature for formation of desired products. This controller consist of two part (1) a nonlinear control method GLC (Global Linearizing Control) to create a linear model of system and (2) a Model predictive controller used to obtain optimal input control sequence. The temperature of reactor is tuned to track a predetermined temperature trajectory that applied to the batch reactor. To do so two input signals, electrical powers and the flow of coolant in the coil are used. Simulation results show that the proposed controller has a remarkable performance for tracking reference trajectory while at the same time it is robust against noise imposed to system output.
Abstract: Monitoring of microbial flora in aquacultured sea bream, in relation to the physicochemical parameters of the rearing seawater, ended to a model describing the influence of the last to the quality of the fisheries. Fishes were sampled during eight months from four aqua farms in Western Greece and analyzed for psychrotrophic, H2S producing bacteria, Salmonella sp., heterotrophic plate count (PCA), with simultaneous physical evaluation. Temperature, dissolved oxygen, pH, conductivity, TDS, salinity, NO3 - and NH4 + ions were recorded. Temperature, dissolved oxygen and conductivity were correlated, respectively, to PCA, Pseudomonas sp. and Shewanella sp. counts. These parameters were the inputs of the model, which was driving, as outputs, to the prediction of PCA, Vibrio sp., Pseudomonas sp. and Shewanella sp. counts, and fish microbiological quality. The present study provides, for the first time, a ready-to-use predictive model of fisheries hygiene, leading to an effective management system for the optimization of aquaculture fisheries quality.
Abstract: Fault-proneness of a software module is the
probability that the module contains faults. To predict faultproneness
of modules different techniques have been proposed which
includes statistical methods, machine learning techniques, neural
network techniques and clustering techniques. The aim of proposed
study is to explore whether metrics available in the early lifecycle
(i.e. requirement metrics), metrics available in the late lifecycle (i.e.
code metrics) and metrics available in the early lifecycle (i.e.
requirement metrics) combined with metrics available in the late
lifecycle (i.e. code metrics) can be used to identify fault prone
modules using Genetic Algorithm technique. This approach has been
tested with real time defect C Programming language datasets of
NASA software projects. The results show that the fusion of
requirement and code metric is the best prediction model for
detecting the faults as compared with commonly used code based
model.