Abstract: The gel-supported precipitation (GSP) process can be
used to make spherical particles (spherules) of nuclear fuel,
particularly for very high temperature reactors (VHTR) and even for
implementing the process called SPHEREPAC. In these different
cases, the main characteristics are the sphericity of the particles to be
manufactured and the control over their grain size. Nonetheless,
depending on the specifications defined for these spherical particles,
the GSP process has intrinsic limits, particularly when fabricating
very small particles. This paper describes the use of secondary
fragmentation (water, water/PVA and uranyl nitrate) on solid
surfaces under varying temperature and vibration conditions to assess
the relevance of using this new technique to manufacture very small
spherical particles by means of a modified GSP process. The
fragmentation mechanisms are monitored and analysed, before the
trends for its subsequent optimised application are described.
Abstract: There are two major variants of the Simplex
Algorithm: the revised method and the standard, or tableau method.
Today, all serious implementations are based on the revised method
because it is more efficient for sparse linear programming problems.
Moreover, there are a number of applications that lead to dense linear
problems so our aim in this paper is to present some computational
results on parallel implementation of dense Simplex Method. Our
implementation is implemented on a SMP cluster using C
programming language and the Message Passing Interface MPI.
Preliminary computational results on randomly generated dense
linear programs support our results.
Abstract: The fixed partial dentures are mainly used in the frontal
part of the dental arch because of their great esthetics. There are
several factors that are associated with the stress state created in
ceramic restorations, including: thickness of ceramic layers,
mechanical properties of the materials, elastic modulus of the
supporting substrate material, direction, magnitude and frequency of
applied load, size and location of occlusal contact areas, residual
stresses induced by processing or pores, restoration-cement
interfacial defects and environmental defects. The purpose of this
study is to evaluate the capability of Polarization Sensitive Optical
Coherence Tomography (PSOCT) in detection and analysis of
possible material defects in metal-ceramic and integral ceramic fixed
partial dentures. As a conclusion, it is important to have a non
invasive method to investigate fixed partial prostheses before their
insertion in the oral cavity in order to satisfy the high stress
requirements and the esthetic function.
Abstract: Currently is characterized production engineering
together with the integration of industrial automation and robotics
such very quick view of to manufacture the products. The production
range is continuously changing, expanding and producers have to be
flexible in this regard. It means that need to offer production
possibilities, which can respond to the quick change. Engineering
product development is focused on supporting CAD software, such
systems are mainly used for product design. That manufacturers are
competitive, it should be kept procured machines made available
capable of responding to output flexibility. In response to that
problem is the development of flexible manufacturing systems,
consisting of various automated systems. The integration of flexible
manufacturing systems and subunits together with product design and
of engineering is a possible solution for this issue. Integration is
possible through the implementation of CIM systems. Such a solution
and finding a hyphen between CAD and procurement system ICIM
3000 from Festo Co. is engaged in the research project and this
contribution. This can be designed the products in CAD systems and
watch the manufacturing process from order to shipping by the
development of methods and processes of integration, This can be
modeled in CAD systems products and watch the manufacturing
process from order to shipping to develop methods and processes of
integration, which will improve support for product design
parameters by monitoring of the production process, by creating of
programs for production using the CAD and therefore accelerates the
a total of process from design to implementation.
Abstract: The Maximum Weighted Independent Set (MWIS)
problem is a classic graph optimization NP-hard problem. Given an
undirected graph G = (V, E) and weighting function defined on the
vertex set, the MWIS problem is to find a vertex set S V whose total
weight is maximum subject to no two vertices in S are adjacent. This
paper presents a novel approach to approximate the MWIS of a graph
using minimum weighted vertex cover of the graph. Computational
experiments are designed and conducted to study the performance
of our proposed algorithm. Extensive simulation results show that
the proposed algorithm can yield better solutions than other existing
algorithms found in the literature for solving the MWIS.
Abstract: This paper presents a new approach for the prob-ability density function estimation using the Support Vector Ma-chines (SVM) and the Expectation Maximization (EM) algorithms.In the proposed approach, an advanced algorithm for the SVM den-sity estimation which incorporates the Mean Field theory in the learning process is used. Instead of using ad-hoc values for the para-meters of the kernel function which is used by the SVM algorithm,the proposed approach uses the EM algorithm for an automatic optimization of the kernel. Experimental evaluation using simulated data set shows encouraging results.
Abstract: In this article we present a methodology which
enables preschool and primary school unlanguaged children to
remember words, phrases and texts with the help of graphic signs -
letters, syllables and words. Reading for a child becomes a support
for speech development. Teaching is based on the principle "from
simple to complex", "a letter - a syllable - a word - a proposal - a
text." Availability of multi-level texts allows using this methodology
for working with children who have different levels of speech
development.
Abstract: This paper introduces a framework that aims to
support the design and development of mobile services. The
traditional innovation process and its supporting instruments in form
of creativity tools, acceptance research and user-generated content
analysis are screened for potentials for improvement. The result is a
reshaped innovation process where acceptance research and usergenerated
content analysis are fully integrated within a creativity
tool. Advantages of this method are the enhancement of design
relevant information for developers and designers and the possibility
to forecast market success.
Abstract: This paper explores the scalability issues associated
with solving the Named Entity Recognition (NER) problem using
Support Vector Machines (SVM) and high-dimensional features. The
performance results of a set of experiments conducted using binary
and multi-class SVM with increasing training data sizes are
examined. The NER domain chosen for these experiments is the
biomedical publications domain, especially selected due to its
importance and inherent challenges. A simple machine learning
approach is used that eliminates prior language knowledge such as
part-of-speech or noun phrase tagging thereby allowing for its
applicability across languages. No domain-specific knowledge is
included. The accuracy measures achieved are comparable to those
obtained using more complex approaches, which constitutes a
motivation to investigate ways to improve the scalability of multiclass
SVM in order to make the solution more practical and useable.
Improving training time of multi-class SVM would make support
vector machines a more viable and practical machine learning
solution for real-world problems with large datasets. An initial
prototype results in great improvement of the training time at the
expense of memory requirements.
Abstract: GSM has undoubtedly become the most widespread
cellular technology and has established itself as one of the most
promising technology in wireless communication. The next
generation of mobile telephones had also become more powerful and
innovative in a way that new services related to the user-s location
will arise. Other than the 911 requirements for emergency location
initiated by the Federal Communication Commission (FCC) of the
United States, GSM positioning can be highly integrated in cellular
communication technology for commercial use. However, GSM
positioning is facing many challenges. Issues like accuracy,
availability, reliability and suitable cost render the development and
implementation of GSM positioning a challenging task. In this paper,
we investigate the optimal mobile position tracking means. We
employ an innovative scheme by integrating the Kalman filter in the
localization process especially that it has great tracking
characteristics. When tracking in two dimensions, Kalman filter is
very powerful due to its reliable performance as it supports
estimation of past, present, and future states, even when performing
in unknown environments. We show that enhanced position tracking
results is achieved when implementing the Kalman filter for GSM
tracking.
Abstract: This paper presents a new approach for the protection
of Thyristor-Controlled Series Compensator (TCSC) line using
Support Vector Machine (SVM). One SVM is trained for fault
classification and another for section identification. This method use
three phase current measurement that results in better speed and
accuracy than other SVM based methods which used single phase
current measurement. This makes it suitable for real-time protection.
The method was tested on 10,000 data instances with a very wide
variation in system conditions such as compensation level, source
impedance, location of fault, fault inception angle, load angle at
source bus and fault resistance. The proposed method requires only
local current measurement.
Abstract: This paper quantifies the impact of providing a shortterm
excess active power support of a variable speed wind turbine
(VSWT) and effect of super magnetic energy storage (SMES) unit on
frequency control, particularly temporary minimum frequency (TMF)
term. To demonstrate the effect of these factors on the power system
frequency, a three-area power system is considered as a test system.
Abstract: The introduction of mass-customization has enabled
new ways to treat patients within medicine. However, the
introduction of industrialized treatments has also meant new
obstacles. The purpose of this study was to introduce and
theoretically test a method for improving dental crown fit. The
optimization method allocates support points in order to check the
final variation for dental crowns. Three different types of geometries
were tested and compared. The three geometries were also divided
into three sub-geometries: Current method, Optimized method and
Feasible method. The Optimized method, using the whole surface for
support points, provided the best results. The results support the
objective of the study. It also seems that the support optimization
method can dramatically improve the robustness of dental crown
treatments.
Abstract: In the traditional buckling analysis of rectangular
plates the classical thin plate theory is generally applied, so
neglecting the plating shear deformation. It seems quite clear that this
method is not totally appropriate for the analysis of thick plates, so
that in the following the two variable refined plate theory proposed
by Shimpi (2006), that permits to take into account the transverse
shear effects, is applied for the buckling analysis of simply supported
isotropic rectangular plates, compressed in one and two orthogonal
directions.
The relevant results are compared with the classical ones and, for
rectangular plates under uniaxial compression, a new direct
expression, similar to the classical Bryan-s formula, is proposed for
the Euler buckling stress.
As the buckling analysis is a widely diffused topic for a variety of
structures, such as ship ones, some applications for plates uniformly
compressed in one and two orthogonal directions are presented and
the relevant theoretical results are compared with those ones obtained
by a FEM analysis, carried out by ANSYS, to show the feasibility of
the presented method.
Abstract: With the demand of mobility by users, wireless
technologies have become the hotspot developing arena. Internet
Engineering Task Force (IETF) working group has developed Mobile
IP to support node mobility. The concept of node mobility indicates
that in spite of the movement of the node, it is still connected to the
internet and all the data transactions are preserved. It provides
location-independent access to Internet. After the incorporation of
host mobility, network mobility has undergone intense research.
There are several intricacies faced in the real world implementation
of network mobility significantly the problem of nested networks and
their consequences. This article is concerned regarding a problem of
nested network called pinball route problem and proposes a solution
to eliminate the above problem. The proposed mechanism is
implemented using NS2 simulation tool and it is found that the
proposed mechanism efficiently reduces the overload caused by the
pinball route problem.
Abstract: This paper is concerned with an investigation into the
localized non-stability of a thin elastic orthotropic semi-infinite plate.
In this study, a semi-infinite plate, simply supported on two edges
and different boundary conditions, clamped, hinged, sliding contact
and free on the other edge, are considered. The mathematical model
is used and a general solution is presented the conditions under which
localized solutions exist are investigated.
Abstract: Medical services are usually provided in hospitals; however, in developing country, some rural residences have fewer opportunities to access in healthcare services due to the limitation of transportation communication. Therefore, in Thailand, there are charitable organizations operating to provide medical treatments to these people by shifting the medical services to operation sites; this is commonly known as mobile medical service. Operation routing is important for the organization to reduce its transportation cost in order to focus more on other important activities; for instance, the development of medical apparatus. VRP is applied to solve the problem of high transportation cost of the studied organization with the searching techniques of saving algorithm to find the minimum total distance of operation route and satisfy available time constraints of voluntary medical staffs.
Abstract: A Decision Support System/Expert System for stock
portfolio selection presented where at first step, both technical and
fundamental data used to estimate technical and fundamental return
and risk (1st phase); Then, the estimated values are aggregated with
the investor preferences (2nd phase) to produce convenient stock
portfolio.
In the 1st phase, there are two expert systems, each of which is
responsible for technical or fundamental estimation. In the technical
expert system, for each stock, twenty seven candidates are identified
and with using rough sets-based clustering method (RC) the effective
variables have been selected. Next, for each stock two fuzzy rulebases
are developed with fuzzy C-Mean method and Takai-Sugeno-
Kang (TSK) approach; one for return estimation and the other for
risk. Thereafter, the parameters of the rule-bases are tuned with backpropagation
method. In parallel, for fundamental expert systems,
fuzzy rule-bases have been identified in the form of “IF-THEN" rules
through brainstorming with the stock market experts and the input
data have been derived from financial statements; as a result two
fuzzy rule-bases have been generated for all the stocks, one for return
and the other for risk.
In the 2nd phase, user preferences represented by four criteria and
are obtained by questionnaire. Using an expert system, four estimated
values of return and risk have been aggregated with the respective
values of user preference. At last, a fuzzy rule base having four rules,
treats these values and produce a ranking score for each stock which
will lead to a satisfactory portfolio for the user.
The stocks of six manufacturing companies and the period of
2003-2006 selected for data gathering.
Abstract: The development and use of mobile devices as well as its integration within education systems to deliver electronic contents and to support real-time communications was the focus of this research. In order to investigate the software engineering issues in using mobile devices a research on electronic content was initiated. The Developed MP3 mobile software solution was developed as a prototype for testing and developing a strategy for designing a usable m-learning environment. The mobile software solution was evaluated using mobile device using the link: http://projects.seeu.edu.mk/mlearn. The investigation also tested the correlation between the two mobile learning indicators: electronic content and attention, based on the Task Based learning instructional method. The mobile software solution ''M-Learn“ was developed as a prototype for testing the approach and developing a strategy for designing usable m-learning environment. The proposed methodology is about what learning modeling approach is more appropriate to use when developing mobile learning software.
Abstract: This paper aims to argue that religion and Faith-based Organizations (FBOs) contribute to building democratic process through the provision of education in Sierra Leone. Sierra Leone experienced a civil war from 1991 to 2002 and about 70 percent of the population lives in poverty. While the government has been in the process of rebuilding the nation, many forms of Civil Society Organizations (CSOs), including FBOs, have played a significant role in promoting social development. Education plays an important role in supporting people-s democratic movements through knowledge acquisition, spiritual enlightenment and empowerment. This paper discusses religious tolerance in Sierra Leone and how FBOs have contributed to the provision of primary education in Sierra Leone. This study is based on the author-s field research, which involved interviews with teachers and development stakeholders, notably government officials, Non-governmental Organizations (NGOs) and FBOs, as well as questionnaires completed by pupils, parents and teachers.