Abstract: In recent years Malaysia has included renewable
energy as an alternative fuel to help in diversifying the country-s
energy reliance on oil, natural gas, coal and hydropower with
biomass and solar energy gaining priority. The scope of this paper is
to look at the designing procedures and analysis of a solar thermal
parabolic trough concentrator by simulation utilizing meteorological
data in several parts of Malaysia. Parameters which include the
aperture area, the diameter of the receiver and the working fluid may
be varied to optimize the design. Aperture area is determined by
considering the width and the length of the concentrator whereas the
geometric concentration ratio (CR) is obtained by considering the
width and diameter of the receiver. Three types of working fluid are
investigated. Theoretically, concentration ratios can be very high in
the range of 10 to 40 000 depending on the optical elements used and
continuous tracking of the sun. However, a thorough analysis is
essential as discussed in this paper where optical precision and
thermal analysis must be carried out to evaluate the performance of
the parabolic trough concentrator as the theoretical CR is not the only
factor that should be considered.
Abstract: Induction motors are being used in greater numbers
throughout a wide variety of industrial and commercial applications
because it provides many benefits and reliable device to convert the
electrical energy into mechanical motion. In some application it-s
desired to control the speed of the induction motor. Because of the
physics of the induction motor the preferred method of controlling its
speed is to vary the frequency of the AC voltage driving the motor. In
recent years, with the microcontroller incorporated into an appliance
it becomes possible to use it to generate the variable frequency AC
voltage to control the speed of the induction motor.
This study investigates the microcontroller based variable
frequency power inverter. the microcontroller is provide the variable
frequency pulse width modulation (PWM) signal that control the
applied voltage on the gate drive, which is provides the required
PWM frequency with less harmonics at the output of the power
inverter.
The fully controlled bridge voltage source inverter has been
implemented with semiconductors power devices isolated gate
bipolar transistor (IGBT), and the PWM technique has been
employed in this inverter to supply the motor with AC voltage.
The proposed drive system for three & single phase power inverter
is simulated using Matlab/Simulink. The Matlab Simulation Results
for the proposed system were achieved with different SPWM. From
the result a stable variable frequency inverter over wide range has
been obtained and a good agreement has been found between the
simulation and hardware of a microcontroller based single phase
inverter.
Abstract: The development of One Tambon One Product
(OTOP) became the policy of the government in 1997 after the
former Prime Minister had been in power. The strategy of sections is
currently set for the policy. OTOP has become the part of the way of
community lives around the country. OTOP may be developed under
changing into ASEAN economic community in 2015 because of the
flow of capitals, productions, and many workers in the region. All
sectors are improved for the change. The purposes of study were to
study the strength and weakness of the OTOP-creating process via its
policy and to lead to the strategy to be able to apply before changing.
The methodology is qualitative to study its policy including
document and to interview experienced persons. The findings showed
that the effort of improvement of all sectors obviously involves with
OTOP development. Particularly, the strategic administration of
OTOP is in every level of the state, central sector, region, and
community.
Abstract: Although silicon photonic devices provide a significantly larger bandwidth and dissipate a substantially less power than the electronic devices, they suffer from a large size due to the fundamental diffraction limit and the weak optical response of Si. A potential solution is to exploit Si plasmonics, which may not only miniaturize the photonic device far beyond the diffraction limit, but also enhance the optical response in Si due to the electromagnetic field confinement. In this paper, we discuss and summarize the recently developed metal-insulator-Si-insulator-metal nanoplasmonic waveguide as well as various passive and active plasmonic components based on this waveguide, including coupler, bend, power splitter, ring resonator, MZI, modulator, detector, etc. All these plasmonic components are CMOS compatible and could be integrated with electronic and conventional dielectric photonic devices on the same SOI chip. More potential plasmonic devices as well as plasmonic nanocircuits with complex functionalities are also addressed.
Abstract: One of the main challenges for one phase anaerobic digestion processes is the high concentration of NH4+ and PO4 3- ions
in the digested sludge supernatant. This project focuses on enhancing the removal of nutrients during the anaerobic digestion process through fixing both NH4+ and PO4 3- ions in the form of struvite (magnesium ammonium phosphate, MAP, MgNH4PO4.6H2O) within the anaerobic sludge. Batch anaerobic digestion tests showed that Mg2+ concentration in the range 279 – 812 mg/L had insignificant effect on CGP but incurred a slight increase in COD removal. The reactor that had soluble Mg2+:NH4+:PO43- at a molar ratio of 1.28:1:00:1:00 achieved the best performance enhancement of 8% increase in COD removal and 32% reduction in NH4+ in the reactor supernatant. Overall, the results show that there is a potential to optimise conventional anaerobic digestion such that supernatant lean in P and N, and sludge rich in nutrients are obtained.
Abstract: This paper describes a steady state model of a multiple
effect evaporator system for simulation and control purposes. The
model includes overall as well as component mass balance equations,
energy balance equations and heat transfer rate equations for area
calculations for all the effects. Each effect in the process is
represented by a number of variables which are related by the energy
and material balance equations for the feed, product and vapor flow
for backward, mixed and split feed. For simulation 'fsolve' solver in
MATLAB source code is used. The optimality of three sequences i.e.
backward, mixed and splitting feed is studied by varying the various
input parameters.
Abstract: The mixture formation prior to the ignition process
plays as a key element in the diesel combustion. Parametric studies of
mixture formation and ignition process in various injection parameter
has received considerable attention in potential for reducing
emissions. Purpose of this study is to clarify the effects of injection
pressure on mixture formation and ignition especially during ignition
delay period, which have to be significantly influences throughout the
combustion process and exhaust emissions. This study investigated
the effects of injection pressure on diesel combustion fundamentally
using rapid compression machine. The detail behavior of mixture
formation during ignition delay period was investigated using the
schlieren photography system with a high speed camera. This method
can capture spray evaporation, spray interference, mixture formation
and flame development clearly with real images. Ignition process and
flame development were investigated by direct photography method
using a light sensitive high-speed color digital video camera. The
injection pressure and air motion are important variable that strongly
affect to the fuel evaporation, endothermic and prolysis process
during ignition delay. An increased injection pressure makes spray tip
penetration longer and promotes a greater amount of fuel-air mixing
occurs during ignition delay. A greater quantity of fuel prepared
during ignition delay period thus predominantly promotes more rapid
heat release.
Abstract: The evaluation and measurement of human body
dimensions are achieved by physical anthropometry. This research
was conducted in view of the importance of anthropometric indices
of the face in forensic medicine, surgery, and medical imaging. The
main goal of this research is to optimization of facial feature point by
establishing a mathematical relationship among facial features and
used optimize feature points for age classification. Since selected
facial feature points are located to the area of mouth, nose, eyes and
eyebrow on facial images, all desire facial feature points are extracted
accurately. According this proposes method; sixteen Euclidean
distances are calculated from the eighteen selected facial feature
points vertically as well as horizontally. The mathematical
relationships among horizontal and vertical distances are established.
Moreover, it is also discovered that distances of the facial feature
follows a constant ratio due to age progression. The distances
between the specified features points increase with respect the age
progression of a human from his or her childhood but the ratio of the
distances does not change (d = 1 .618 ) . Finally, according to the
proposed mathematical relationship four independent feature
distances related to eight feature points are selected from sixteen
distances and eighteen feature point-s respectively. These four feature
distances are used for classification of age using Support Vector
Machine (SVM)-Sequential Minimal Optimization (SMO) algorithm
and shown around 96 % accuracy. Experiment result shows the
proposed system is effective and accurate for age classification.
Abstract: Human immunodeficiency virus infection and
acquired immunodeficiency syndrome is a global pandemic with
cases reporting from virtually every country and continues to be a
common infection in developing country like India.
Microalbuminuria is a manifestation of human immunodeficiency
virus associated nephropathy. Therefore, microalbuminuria may be
an early marker of human immunodeficiency virus associated
nephropathy, and screening for its presence may be beneficial. A
strikingly high prevalence of microalbuminuria among human
immunodeficiency virus infected patients has been described in
various studies. Risk factors for clinically significant proteinuria
include African - American race, higher human immunodeficiency
virus ribonucleic acid level and lower CD4 lymphocyte count. The
cardiovascular risk factors of increased systolic blood pressure and
increase fasting blood sugar level are strongly associated with
microalbuminuria in human immunodeficiency virus patient. These
results suggest that microalbuminuria may be a sign of current
endothelial dysfunction and micro-vascular disease and there is
substantial risk of future cardiovascular disease events. Positive
contributing factors include early kidney disease such as human
immunodeficiency virus associated nephropathy, a marker of end
organ damage related to co morbidities of diabetes or hypertension,
or more diffuse endothelial cells dysfunction. Nevertheless after
adjustment for non human immunodeficiency virus factors, human
immunodeficiency virus itself is a major risk factor. The presence of
human immunodeficiency virus infection is independent risk to
develop microalbuminuria in human immunodeficiency virus patient.
Cardiovascular risk factors appeared to be stronger predictors of
microalbuminuria than markers of human immunodeficiency virus
severity person with human immunodeficiency virus infection and
microalbuminuria therefore appear to potentially bear the burden of
two separate damage related to known vascular end organ damage
related to know vascular risk factors, and human immunodeficiency
virus specific processes such as the direct viral infection of kidney
cells.The higher prevalence of microalbuminuria among the human
immunodeficiency virus infected could be harbinger of future
increased risks of both kidney and cardiovascular disease. Further
study defining the prognostic significance of microalbuminuria
among human immunodeficiency virus infected persons will be
essential. Microalbuminuria seems to be a predictor of cardiovascular
disease in diabetic and non diabetic subjects, hence it can also be
used for early detection of micro vascular disease in human
immunodeficiency virus positive patients, thus can help to diagnose
the disease at the earliest.
Abstract: The nickel and gold nanoclusters as supported
catalysts were analyzed by XAS, XRD and XPS in order to
determine their local, global and electronic structure. The present
study has pointed out a strong deformation of the local structure of
the metal, due to its interaction with oxide supports. The average
particle size, the mean squares of the microstrain, the particle size
distribution and microstrain functions of the supported Ni and Au
catalysts were determined by XRD method using Generalized Fermi
Function for the X-ray line profiles approximation. Based on EXAFS
analysis we consider that the local structure of the investigated
systems is strongly distorted concerning the atomic number pairs.
Metal-support interaction is confirmed by the shape changes of the
probability densities of electron transitions: Ni K edge (1s →
continuum and 2p), Au LIII-edge (2p3/2 → continuum, 6s, 6d5/2 and
6d3/2). XPS investigations confirm the metal-support interaction at
their interface.
Abstract: Optimal capacitor allocation in distribution systems
has been studied for a long times. It is an optimization problem
which has an objective to define the optimal sizes and locations of
capacitors to be installed. In this works, an overview of capacitor
placement problem in distribution systems is briefly introduced. The
objective functions and constraints of the problem are listed and the
methodologies for solving the problem are summarized.
Abstract: The Influence Diagrams (IDs) is a kind of Probabilistic Belief Networks for graphic modeling. The usage of IDs can improve the communication among field experts, modelers, and decision makers, by showing the issue frame discussed from a high-level point of view. This paper enhances the Time-Sliced Influence Diagrams (TSIDs, or called Dynamic IDs) based formalism from a Discrete Event Systems Modeling and Simulation (DES M&S) perspective, for Exploring Analysis (EA) modeling. The enhancements enable a modeler to specify times occurred of endogenous events dynamically with stochastic sampling as model running and to describe the inter- influences among them with variable nodes in a dynamic situation that the existing TSIDs fails to capture. The new class of model is named Dynamic-Stochastic Influence Diagrams (DSIDs). The paper includes a description of the modeling formalism and the hiberarchy simulators implementing its simulation algorithm, and shows a case study to illustrate its enhancements.
Abstract: The design of weight is one of the important parts in
fuzzy decision making, as it would have a deep effect on the evaluation
results. Entropy is one of the weight measure based on objective
evaluation. Non--probabilistic-type entropy measures for fuzzy set
and interval type-2 fuzzy sets (IT2FS) have been developed and applied
to weight measure. Since the entropy for (IT2FS) for decision
making yet to be explored, this paper proposes a new objective
weight method by using entropy weight method for multiple attribute
decision making (MADM). This paper utilizes the nature of IT2FS
concept in the evaluation process to assess the attribute weight based
on the credibility of data. An example was presented to demonstrate
the feasibility of the new method in decision making. The entropy
measure of interval type-2 fuzzy sets yield flexible judgment and
could be applied in decision making environment.
Abstract: In the present work homogeneous silica film on
silicon was fabricated by colloidal silica sol. The silica sol precursor
with uniformly granular particle was derived by the alkaline
hydrolysis of tetraethoxyorthosilicate (TEOS) in presence of glycerol
template. The film was prepared by dip coating process. The
templated hetero-structured silica film was annealed at elevated
temperatures to generate nano- and meso porosity in the film. The
film was subsequently annealed at different temperatures to make it
defect free and abrasion resistant. The sol and the film were
characterized by the measurement of particle size distribution,
scanning electron microscopy, XRD, FTIR spectroscopy,
transmission electron microscopy, atomic force microscopy,
measurement of the refractive index, thermal conductivity and
abrasion resistance. The porosity of the films decreased whereas
refractive index and dielectric constant of it `increased with the
increase in the annealing temperature. The thermal conductivity of
the films increased with the increase in the film thickness. The
developed porous silica film holds strong potential for use in
different areas.
Abstract: Combustion of sprays is of technological importance, but its flame behavior is not fully understood. Furthermore, the multiplicity of dependent variables such as pressure, temperature, equivalence ratio, and droplet sizes complicates the study of spray combustion. Fundamental study on the influence of the presence of liquid droplets has revealed that laminar flames within aerosol mixtures more readily become unstable than for gaseous ones and this increases the practical burning rate. However, fundamental studies on turbulent flames of aerosol mixtures are limited particularly those under near mono-dispersed droplet conditions. In the present work, centrally ignited expanding flames at near atmospheric pressures are employed to quantify the burning rates in gaseous and aerosol flames. Iso-octane-air aerosols are generated by expansion of the gaseous pre-mixture to produce a homogeneously distributed suspension of fuel droplets. The effects of the presence of droplets and turbulence velocity in relation to the burning rates of the flame are also investigated.
Abstract: Corner detection and optical flow are common techniques for feature-based video stabilization. However, these algorithms are computationally expensive and should be performed at a reasonable rate. This paper presents an algorithm for discarding irrelevant feature points and maintaining them for future use so as to improve the computational cost. The algorithm starts by initializing a maintained set. The feature points in the maintained set are examined against its accuracy for modeling. Corner detection is required only when the feature points are insufficiently accurate for future modeling. Then, optical flows are computed from the maintained feature points toward the consecutive frame. After that, a motion model is estimated based on the simplified affine motion model and least square method, with outliers belonging to moving objects presented. Studentized residuals are used to eliminate such outliers. The model estimation and elimination processes repeat until no more outliers are identified. Finally, the entire algorithm repeats along the video sequence with the points remaining from the previous iteration used as the maintained set. As a practical application, an efficient video stabilization can be achieved by exploiting the computed motion models. Our study shows that the number of times corner detection needs to perform is greatly reduced, thus significantly improving the computational cost. Moreover, optical flow vectors are computed for only the maintained feature points, not for outliers, thus also reducing the computational cost. In addition, the feature points after reduction can sufficiently be used for background objects tracking as demonstrated in the simple video stabilizer based on our proposed algorithm.
Abstract: The dynamic spectrum allocation solutions such as
cognitive radio networks have been proposed as a key technology to
exploit the frequency segments that are spectrally underutilized.
Cognitive radio users work as secondary users who need to
constantly and rapidly sense the presence of primary users or
licensees to utilize their frequency bands if they are inactive. Short
sensing cycles should be run by the secondary users to achieve
higher throughput rates as well as to provide low level of interference
to the primary users by immediately vacating their channels once
they have been detected. In this paper, the throughput-sensing time
relationship in local and cooperative spectrum sensing has been
investigated under two distinct scenarios, namely, constant primary
user protection (CPUP) and constant secondary user spectrum
usability (CSUSU) scenarios. The simulation results show that the
design of sensing slot duration is very critical and depends on the
number of cooperating users under CPUP scenario whereas under
CSUSU, cooperating more users has no effect if the sensing time
used exceeds 5% of the total frame duration.
Abstract: Titanium gels doped with water-soluble cationic porphyrin were synthesized by the sol–gel polymerization of Ti (OC4H9)4. In this work we investigate the spectroscopic properties along with SEM images of tetra carboxyl phenyl porphyrin when incorporated into porous matrix produced by the sol–gel technique.
Abstract: Structural Integrity Management (SIM) is
important for the protection of offshore crew, environment, business assets and company and industry reputation. API RP 2A contained guidelines for assessment of existing platforms mostly for the Gulf
of Mexico (GOM). ISO 19902 SIM framework also does not
specifically cater for Malaysia. There are about 200 platforms in
Malaysia with 90 exceeding their design life. The Petronas Carigali
Sdn Bhd (PCSB) uses the Asset Integrity Management System and
the very subjective Risk based Inspection Program for these
platforms. Petronas currently doesn-t have a standalone Petronas
Technical Standard PTS-SIM. This study proposes a recommended
practice for the SIM process for offshore structures in Malaysia,
including studies by API and ISO and local elements such as the
number of platforms, types of facilities, age and risk ranking. Case
study on SMG-A platform in Sabah shows missing or scattered
platform data and a gap in inspection history. It is to undergo a level
3 underwater inspection in year 2015.
Abstract: In this paper, we propose ablock-wise watermarking scheme for color image authentication to resist malicious tampering of digital media. The thresholding technique is incorporated into the scheme such that the tampered region of the color image can be recovered with high quality while the proofing result is obtained. The watermark for each block consists of its dual authentication data and the corresponding feature information. The feature information for recovery iscomputed bythe thresholding technique. In the proofing process, we propose a dual-option parity check method to proof the validity of image blocks. In the recovery process, the feature information of each block embedded into the color image is rebuilt for high quality recovery. The simulation results show that the proposed watermarking scheme can effectively proof the tempered region with high detection rate and can recover the tempered region with high quality.