Abstract: Sedimentation is a hydraulic phenomenon that is
emerging as a serious challenge in river engineering. When the flow
reaches a certain state that gather potential energy, it shifts the
sediment load along channel bed. The transport of such materials can
be in the form of suspended and bed loads. The movement of these
along the river course and channels and the ways in which this could
influence the water intakes is considered as the major challenges for
sustainable O&M of hydraulic structures. This could be very serious
in arid and semi-arid regions like Iran, where inappropriate watershed
management could lead to shifting a great deal of sediments into the
reservoirs and irrigation systems. This paper aims to investigate
sedimentation in the Western Canal of Dez Diversion Weir in Iran,
identifying factors which influence the process and provide ways in
which to mitigate its detrimental effects by using the SHARC
Software.
For the purpose of this paper, data from the Dezful water authority
and Dezful Hydrometric Station pertinent to a river course of about 6
Km were used.
Results estimated sand and silt bed loads concentrations to be 193
ppm and 827ppm respectively. Given the available data on average
annual bed loads and average suspended sediment loads of 165ppm
and 837ppm, there was a significant statistical difference (16%)
between the sand grains, whereas no significant difference (1.2%)
was find in the silt grain sizes. One explanation for such finding
being that along the 6 Km river course there was considerable
meandering effects which explains recent shift in the hydraulic
behavior along the stream course under investigation. The sand
concentration in downstream relative to present state of the canal
showed a steep descending curve. Sediment trapping on the other
hand indicated a steep ascending curve. These occurred because the
diversion weir was not considered in the simulation model.
Abstract: This study proposes a materials procurement contracts
model to which the zero-cost collar option is applied for heading price
fluctuation risks in construction.The material contract model based on
the collar option that consists of the call option striking zone of the
construction company(the buyer) following the materials price
increase andthe put option striking zone of the material vendor(the
supplier) following a materials price decrease. This study first
determined the call option strike price Xc of the construction company
by a simple approach: it uses the predicted profit at the project starting
point and then determines the strike price of put option Xp that has an
identical option value, which completes the zero-cost material
contract.The analysis results indicate that the cost saving of the
construction company increased as Xc decreased. This was because the
critical level of the steel materials price increasewas set at a low level.
However, as Xc decreased, Xpof a put option that had an identical
option value gradually increased. Cost saving increased as Xc
decreased. However, as Xp gradually increased, the risk of loss from a
construction company increased as the steel materials price decreased.
Meanwhile, cost saving did not occur for the construction company,
because of volatility. This result originated in the zero-cost features of
the two-way contract of the collar option. In the case of the regular
one-way option, the transaction cost had to be subtracted from the cost
saving. The transaction cost originated from an option value that
fluctuated with the volatility. That is, the cost saving of the one-way
option was affected by the volatility. Meanwhile, even though the
collar option with zero transaction cost cut the connection between
volatility and cost saving, there was a risk of exercising the put option.
Abstract: The aim of the work was to attenuate the vibration amplitude in CESNA 172 airplane wing by using Functionally Graded Material instead of uniform or composite material. Wing strength was achieved by means of stress analysis study, while wing vibration amplitudes and shapes were achieved by means of Modal and Harmonic analysis. Results were verified by applying the methodology in a simple cantilever plate to the simple model and the results were promising and the same methodology can be applied to the airplane wing model. Aluminum models, Titanium models, and functionally graded materials of Aluminum and titanium results were compared to show a great vibration attenuation after using the FGM. Optimization in FGM gradation satisfied our objective of reducing and attenuating the vibration amplitudes to show the effect of using FGM in vibration behavior. Testing the Aluminum rich models, and comparing it with the titanium rich model was an optimization in this paper. Results have shown a significant attenuation in vibration magnitudes when using FGM instead of Titanium Plate, and Aluminium wing with FGM Spurs instead of Aluminium wings. It was also recommended that in future, changing the graphical scale to 1:10 or even 1:1 when the computers- capabilities allow.
Abstract: Sport is one of the sectors in which the largest
technical projections regarding the functions of textiles can be found.
He is a large consumer of high performance composite materials and
new fibers. It is one of the sectors where the innovation is the most
important when the greatest numbers of spectacular developments are
aimed at increasing performance. In medicine, textile innovation is
used and contributes in the amelioration of different materials such as
dressing, orthosis, bandages, etc. The hygienic textiles in non-woven
materials record a strong growth. The objective of this study is to
show the different advances of development we obtained in the both
ways (sport and medicine). Polyamide fibers where developed
tacking into account the specification of the high level athlete’s
performance like swimming and triathlon (Olympic Games, Brazil
2016). The first textile utilization was for skiing (Olympic Games,
Sotchi 2014). The different textiles technologies where adapted for
medicine.
Abstract: A time-domain numerical model within the
framework of transmission line modeling (TLM) is developed to
simulate electromagnetic pulse propagation inside multiple
microcavities forming photonic crystal (PhC) structures. The model
developed is quite general and is capable of simulating complex
electromagnetic problems accurately. The field quantities can be
mapped onto a passive electrical circuit equivalent what ensures that
TLM is provably stable and conservative at a local level.
Furthermore, the circuit representation allows a high level of
hybridization of TLM with other techniques and lumped circuit
models of components and devices. A photonic crystal structure
formed by rods (or blocks) of high-permittivity dieletric material
embedded in a low-dielectric background medium is simulated as an
example. The model developed gives vital spatio-temporal
information about the signal, and also gives spectral information over
a wide frequency range in a single run. The model has wide
applications in microwave communication systems, optical
waveguides and electromagnetic materials simulations.
Abstract: A new generation product made from bamboo strips,
known as laminated bamboo, has gained importance. The objective
of this research was to experiment the effect of three factors on the
mechanical property of laminated bamboo. The interested factors for
experimental design were (A) four bamboo species, namely Bambusa
blumeana Schultes (Pai See Suk), Dendrocalamus asper Backer (Pai
Tong), Dendrocalamus hamiltonii Nees (Pai Hok) and
Dendrocalamus sericeus Munro (Pai Sang Mon), (B) two types of
glue adhesive, polyvinyl acetate emulsion (PVAC) fortified with
urea-formaldehyde (UF) and urea-formaldehyde (UF) to make
parallel-oriented bamboo strips laminates and (C) glue weight per
strip area, 150 g/m2 and 190 g/m2. Experimental results showed that
Dendrocalamus asper Backer (Pai Tong) and Dendrocalamus
sericeus Munro (Pai Sang Mon) were best used for manufacturing
due to their highest MOR and MOE. The amount of glue weight 150
g/m2 yielded higher MOR and MOE than the amount of glue weight
190 g/m2. At the conclusion, the laminated bamboo manufacturers
can benefit from this research in order to select right materials
according to strength, cost and accessibility.
Abstract: The excellent suitability of the externally excited synchronous
machine (EESM) in automotive traction drive applications
is justified by its high efficiency over the whole operation range and
the high availability of materials. Usually, maximum efficiency is
obtained by modelling each single loss and minimizing the sum of all
losses. As a result, the quality of the optimization highly depends on
the precision of the model. Moreover, it requires accurate knowledge
of the saturation dependent machine inductances. Therefore, the
present contribution proposes a method to minimize the overall losses
of a salient pole EESM and its inverter in steady state operation based
on measurement data only. Since this method does not require any
manufacturer data, it is well suited for an automated measurement
data evaluation and inverter parametrization. The field oriented control
(FOC) of an EESM provides three current components resp. three
degrees of freedom (DOF). An analytic minimization of the copper
losses in the stator and the rotor (assuming constant inductances) is
performed and serves as a first approximation of how to choose the
optimal current reference values. After a numeric offline minimization
of the overall losses based on measurement data the results are
compared to a control strategy that satisfies cos (ϕ) = 1.
Abstract: The article presents a new method for detection of
artificial objects and materials from images of the environmental
(non-urban) terrain. Our approach uses the hue and saturation (or Cb
and Cr) components of the image as the input to the segmentation
module that uses the mean shift method. The clusters obtained as the
output of this stage have been processed by the decision-making
module in order to find the regions of the image with the significant
possibility of representing human. Although this method will detect
various non-natural objects, it is primarily intended and optimized for
detection of humans; i.e. for search and rescue purposes in non-urban
terrain where, in normal circumstances, non-natural objects shouldn-t
be present. Real world images are used for the evaluation of the
method.
Abstract: Many non-conventional adsorbent have been studied
as economic alternative to commercial activated carbon and mostly
agricultural waste have been introduced such as rubber leaf powder
and hazelnut shell. Microwave Incinerated Rice Husk Ash
(MIRHA), produced from the rice husk is one of the low-cost
materials that were used as adsorbent of heavy metal. The aim of
this research was to study the feasibility of using MIRHA500 and
MIRHA800 as adsorbent for the removal of Cu(II) metal ions from
aqueous solutions by the batch studies. The adsorption of Cu(II) into
MIRHA500 and MIRH800 favors Fruendlich isotherm and imply
pseudo – kinetic second order which applied chemisorptions
Abstract: This paper describes a study of geometrically
nonlinear free vibration of thin circular functionally graded (CFGP)
plates resting on Winkler elastic foundations. The material properties
of the functionally graded composites examined here are assumed to
be graded smoothly and continuously through the direction of the
plate thickness according to a power law and are estimated using the
rule of mixture. The theoretical model is based on the classical Plate
theory and the Von-Kármán geometrical nonlinearity assumptions.
An homogenization procedure (HP) is developed to reduce the
problem considered here to that of isotropic homogeneous circular
plates resting on Winkler foundation. Hamilton-s principle is applied
and a multimode approach is derived to calculate the fundamental
nonlinear frequency parameters which are found to be in a good
agreement with the published results. On the other hand, the
influence of the foundation parameters on the nonlinear fundamental
frequency has also been analysed.
Abstract: In the past decade, the development of microstrip
sensor application has evolved tremendously. Although cut and trial
method was adopted to develop microstrip sensing applications in the
past, Computer-Aided-Design (CAD) is a more effective as it ensures
less time is consumed and cost saving is achieved in developing
microstrip sensing applications. Therefore microstrip sensing
applications has gained popularity as an effective tool adopted in
continuous sensing of moisture content particularly in products that is
administered mainly by liquid content. In this research, the Cole-Cole
representation of reactive relaxation is applied to assess the
performance of the microstrip sensor devices. The microstrip sensor
application is an effective tool suitable for sensing the moisture
content of dielectric material. Analogous to dielectric relaxation
consideration of Cole-Cole diagrams as applied to dielectric
materials, a “reactive relaxation concept” concept is introduced to
represent the frequency-dependent and moisture content
characteristics of microstrip sensor devices.
Abstract: The main aim of the presented experiments is to
improve behaviour of sandwich structures under dynamic loading,
such as crash or explosion. Several cellular materials are widely used
as core of the sandwich structures and their properties influence
the response of the entire element under impact load. To optimize
their performance requires the characterisation of the core material
behaviour at high strain rates and identification of the underlying
mechanism. This work presents the study of high strain-rate
characteristics of a specific porous lightweight blast energy absorbing
foam using a Split Hopkinson Pressure Bar (SHPB) technique
adapted to perform tests on low strength materials. Two different
velocities, 15 and 30 m.s-1 were used to determine the strain
sensitivity of the material. Foams were designed using two types of
porous lightweight spherical raw materials with diameters of 30-
100 *m, combined with polymer matrix. Cylindrical specimens with
diameter of 15 mm and length of 7 mm were prepared and loaded
using a Split Hopkinson Pressure Bar apparatus to assess the relation
between the composition of the material and its shock wave
attenuation capacity.
Abstract: In recent years, rehabilitation has been the subject of extensive research due to increased spending on building work and repair of built works. In all cases, it is absolutely essential to carry out methods of strengthening or repair of structural elements, and that following an inspection analysis and methodology of a correct diagnosis. The reinforced concrete columns are important elements in building structures. They support the vertical loads and provide bracing against the horizontal loads. This research about the behavior of reinforced concrete rectangular columns, rehabilitated by concrete liner, confinement FRP fabric, steel liner or cage formed by metal corners. It allows comparing the contributions of different processes used perspective section resistance elements rehabilitated compared to that is not reinforced or repaired. The different results obtained revealed a considerable gain in bearing capacity failure of reinforced sections cladding concrete, metal bracket, steel plates and a slight improvement to the section reinforced with fabric FRP. The use of FRP does not affect the weight of the structures, but the use of different techniques cladding increases the weight of elements rehabilitated and therefore the weight of the building which requires resizing foundations.
Abstract: Future astronomical projects on large space x-ray
imaging telescopes require novel substrates and technologies for the
construction of their reflecting mirrors. The mirrors must be
lightweight and precisely shaped to achieve large collecting area with
high angular resolution. The new materials and technologies must be
cost-effective. Currently, the most promising materials are glass or
silicon foils. We focused on precise shaping these foils by thermal
forming process. We studied free and forced slumping in the
temperature region of hot plastic deformation and compared the
shapes obtained by the different slumping processes. We measured
the shapes and the surface quality of the foils. In the experiments, we
varied both heat-treatment temperature and time following our
experiment design. The obtained data and relations we can use for
modeling and optimizing the thermal forming procedure.
Abstract: The production of glass, ceramic materials and many non-ferrous metals (Zn, Cu, Pb, etc.), ferrous metals (pig iron) and others is connected with the use of a considerable number of initial solid raw materials. Before carrying out the basic technological processes (oxidized roasting, melting, agglomeration, baking) it is necessary to mix and homogenize the raw materials that have different chemical and phase content, granulometry and humidity. For this purpose zinc sulfide concentrates differing in origin are studied for their more complete characteristics using chemical, X-ray diffraction analyses, DTA and TGA as well as Mössbauer spectroscopy. The phases established in most concentrates are: β-ZnS, mZnS.nFeS, FeS2, CuFeS2, PbS, SiO2 (α-quartz). With the help of the developed by us a Web-based information system for a continued period of time different mix proportions from zinc concentrates are calculated and used in practice (roasting in fluidized bed reactor), which have to conform to the technological requirements of the zinc hydrometallurgical technological scheme.
Abstract: A suspension bridge is the most suitable type of structure for a long-span bridge due to rational use of structural materials. Increased deformability, which is conditioned by appearance of the elastic and kinematic displacements, is the major disadvantage of suspension bridges. The problem of increased kinematic displacements under the action of non-symmetrical load can be solved by prestressing. The prestressed suspension bridge with the span of 200 m was considered as an object of investigations. The cable truss with the cross web was considered as the main load carrying structure of the prestressed suspension bridge. The considered cable truss was optimized by 47 variable factors using Genetic algorithm and FEM program ANSYS. It was stated, that the maximum total displacements are reduced up to 29.9% by using of the cable truss with the rational characteristics instead of the single cable in the case of the worst situated load.
Abstract: In areas of low to moderate seismicity many building contents and equipment are not positively fixed to the floor or tied to adjacent walls. Under seismic induced horizontal vibration, such contents and equipment can suffer from damage by either overturning or impact associated with rocking. This paper focuses on the estimation of shock on typical contents and equipment due to rocking. A simplified analytical model is outlined that can be used to estimate the maximum acceleration on a rocking object given its basic geometric and mechanical properties. The developed model was validated against experimental results. The experimental results revealed that the maximum shock acceleration can be underestimated if the static stiffness of the materials at the interface between the rocking object and floor is used rather than the dynamic stiffness. Excellent agreement between the model and experimental results was found when the dynamic stiffness for the interface material was used, which was found to be generally much higher than corresponding static stiffness under different investigated boundary conditions of the cushion. The proposed model can be a beneficial tool in performing a rapid assessment of shock sensitive components considered for possible seismic rectification.
Abstract: Recently, several designs of single fed circularly
polarized microstrip antennas have been studied. Relatively, a few
designs for achieving circular polarization using triangular microstrip
antenna are available. Typically existing design of single fed
circularly polarized triangular microstrip antennas include the use of
equilateral triangular patch with a slit or a horizontal slot on the patch
or addition a narrow band stub on the edge or a vertex of triangular
patch.
In other word, with using a narrow band tune stub on middle of an
edge of triangle causes of facility to compensate the possible
fabrication error and substrate materials with easier adjusting the
tuner stub length. Even though disadvantages of this method is very
long of stub (approximate 1/3 length of triangle edge). In this paper,
instead of narrow band stub, a wide band stub has been applied,
therefore the length of stub by this method has been decreased
around 1/10 edge of triangle in addition changing the aperture angle
of stub, provides more facility for designing and producing circular
polarization wave.
Abstract: With the development of the Polyvinyl chloride
(PVC) products in many applications, the challenge of investigating
the raw material composition and reducing the cost have both
become more and more important. Considerable research has been
done investigating the effect of additives on the PVC products. Most
of the PVC composites research investigates only the effect of
single/few factors, at a time. This isolated consideration of the input
factors does not take in consideration the interaction effect of the
different factors. This paper implements a mixture experimental
design approach to find out a cost-effective PVC composition for the
production of electrical-insulation cables considering the ASTM
Designation (D) 6096. The results analysis showed that a minimum
cost can be achieved through using 20% virgin PVC, 18.75%
recycled PVC, 43.75% CaCO3 with participle size 10 microns, 14%
DOP plasticizer, and 3.5% CPW plasticizer. For maximum UTS the
compound should consist of: 17.5% DOP, 62.5% virgin PVC, and
20.0% CaCO3 of particle size 5 microns. Finally, for the highest
ductility the compound should be made of 35% virgin PVC, 20%
CaCO3 of particle size 5 microns, and 45.0% DOP plasticizer.
Abstract: This work deals with the initial applications and formulation of an anisotropic plastic-damage constitutive model proposed for non-linear analysis of reinforced concrete structures submitted to a loading with change of the sign. The original constitutive model is based on the fundamental hypothesis of energy equivalence between real and continuous medium following the concepts of the Continuum Damage Mechanics. The concrete is assumed as an initial elastic isotropic medium presenting anisotropy, permanent strains and bimodularity (distinct elastic responses whether traction or compression stress states prevail) induced by damage evolution. In order to take into account the bimodularity, two damage tensors governing the rigidity in tension or compression regimes are introduced. Then, some conditions are introduced in the original version of the model in order to simulate the damage unilateral effect. The three-dimensional version of the proposed model is analyzed in order to validate its formulation when compared to micromechanical theory. The one-dimensional version of the model is applied in the analyses of a reinforced concrete beam submitted to a loading with change of the sign. Despite the parametric identification problems, the initial applications show the good performance of the model.