Abstract: Modelling techniques for a fluid coupling taken from
published literature have been extended to include the effects of the
filling and emptying of the coupling with oil and the variation in
losses when the coupling is partially full. In the model, the fluid flow
inside the coupling is considered to have two principal velocity
components; one circumferentially about the coupling axis
(centrifugal head) and the other representing the secondary vortex
within the coupling itself (vortex head). The calculation of liquid
mass flow rate circulating between the two halves of the coupling is
based on: the assumption of a linear velocity variation in the
circulating vortex flow; the head differential in the fluid due to the
speed difference between the two shafts; and the losses in the
circulating vortex flow as a result of the impingement of the flow
with the blades in the coupling and friction within the passages
between the blades.
Abstract: Rapid urbanization, industrialization and population
growth have led to an increase in number of automobiles that cause
air pollution. It is estimated that road traffic contributes 60% of air
pollution in urban areas. A case by case assessment is required to
predict the air quality in urban situations, so as to evolve certain
traffic management measures to maintain the air quality levels with
in the tolerable limits. Calicut city in the state of Kerala, India has
been chosen as the study area. Carbon Monoxide (CO) concentration
was monitored at 15 links in Calicut city and air quality performance
was evaluated over each link. The CO pollutant concentration values
were compared with the National Ambient Air Quality Standards
(NAAQS), and the CO values were predicted by using CALINE4 and
IITLS and Linear regression models. The study has revealed that
linear regression model performs better than the CALINE4 and
IITLS models. The possible association between CO pollutant
concentration and traffic parameters like traffic flow, type of vehicle,
and traffic stream speed was also evaluated.
Abstract: The performance and the plasma created by a pulsed
magnetoplasmadynamic thruster for small satellite application is
studied to understand better the ablation and plasma propagation
processes occurring during the short-time discharge. The results can
be applied to improve the quality of the thruster in terms of efficiency,
and to tune the propulsion system to the needs required by the satellite
mission. Therefore, plasma measurements with a high-speed camera
and induction probes, and performance measurements of mass bit
and impulse bit were conducted. Values for current sheet propagation
speed, mean exhaust velocity and thrust efficiency were derived from
these experimental data. A maximum in current sheet propagation
was found by the high-speed camera measurements for a medium
energy input and confirmed by the induction probes. A quasilinear
tendency between the mass bit and the energy input, the current
action integral respectively, was found, as well as a linear tendency
between the created impulse and the discharge energy. The highest
mean exhaust velocity and thrust efficiency was found for the highest
energy input.
Abstract: The back propagation algorithm calculates the weight
changes of artificial neural networks, and a common approach is to
use a training algorithm consisting of a learning rate and a
momentum factor. The major drawbacks of above learning algorithm
are the problems of local minima and slow convergence speeds. The
addition of an extra term, called a proportional factor reduces the
convergence of the back propagation algorithm. We have applied the
three term back propagation to multiplicative neural network
learning. The algorithm is tested on XOR and parity problem and
compared with the standard back propagation training algorithm.
Abstract: Predicting short term wind speed is essential in order
to prevent systems in-action from the effects of strong winds. It also
helps in using wind energy as an alternative source of energy, mainly
for Electrical power generation. Wind speed prediction has
applications in Military and civilian fields for air traffic control,
rocket launch, ship navigation etc. The wind speed in near future
depends on the values of other meteorological variables, such as
atmospheric pressure, moisture content, humidity, rainfall etc. The
values of these parameters are obtained from a nearest weather
station and are used to train various forms of neural networks. The
trained model of neural networks is validated using a similar set of
data. The model is then used to predict the wind speed, using the
same meteorological information. This paper reports an Artificial
Neural Network model for short term wind speed prediction, which
uses back propagation algorithm.
Abstract: In turning hardened steel, polycrystalline cubic boron
nitride (cBN) compacts are widely used, due to their higher hardness
and higher thermal conductivity. However, in milling hardened steel,
fracture of cBN cutting tools readily occurs because they have poor
fracture toughness. Therefore, coated cemented carbide tools, which
have good fracture toughness and wear resistance, are generally
widely used. In this study, hardened steel (ASTM D2, JIS SKD11,
60HRC) was milled with three physical vapor deposition
(PVD)-coated cemented carbide end mill cutters in order to determine
effective tool materials for cutting hardened steel at high cutting
speeds. The coating films used were (Ti,W)N/(Ti,W,Si)N and
(Ti,W)N/(Ti,W,Si,Al)N coating films. (Ti,W,Si,Al)N is a new type of
coating film. The inner layer of the (Ti,W)N/(Ti,W,Si)N and
(Ti,W)N/(Ti,W,Si,Al)N coating system is (Ti,W)N coating film, and
the outer layer is (Ti,W,Si)N and (Ti,W,Si,Al)N coating films,
respectively. Furthermore, commercial (Ti,Al)N-based coating film
was also used. The following results were obtained: (1) In milling
hardened steel at a cutting speed of 3.33 m/s, the tool wear width of the
(Ti,W)N/(Ti,W,Si,Al)N-coated tool was smaller than that of the
(Ti,W)N/(Ti,W,Si)N-coated tool. And, compared with the commercial
(Ti,Al)N, the tool wear width of the (Ti,W)N/(Ti,W,Si,Al)N-coated
tool was smaller than that of the (Ti,Al)N-coated tool. (2) The tool
wear of the (Ti,W)N/(Ti,W,Si,Al)N-coated tool increased with an
increase in cutting speed. (3) The (Ti,W)N/(Ti,W,Si,Al)N-coated
cemented carbide was an effective tool material for high-speed cutting
below a cutting speed of 3.33 m/s.
Abstract: In this paper by measuring the cutting forces the effect
of the tool shape and qualifications (sharp and worn cutting tools of
both vee and knife edge profile) and cutting conditions (depth of cut
and cutting speed) in the turning operation on the tool deflection and
cutting force is investigated. The workpiece material was mild steel
and the cutting tool was made of high speed steel. Cutting forces
were measured by a dynamometer (type P.E.I. serial No 154). The
dynamometer essentially consisted of a cantilever structure which
held the cutting tool. Deflection of the cantilever was measured by an
L.V.D.T (Mercer 122) deflection indicator. No cutting fluid was used
during the turning operations. A modern CNC lathe machine (Okuma
LH35-N) was used for the tests. It was noted that worn vee profile
tools tended to produce a greater increase in the vertical force
component than the axial component, whereas knife tools tended to
show a more pronounced increase in the axial component.
Abstract: Xanthan gum is a microbial polysaccharide of great
commercial significance. The purpose of this study was to select the
optimum fermentation time for xanthan gum production by
Xanthomonas campestris (NRRL-B-1459) using 10% sugar beet
molasses as a carbon source. The pre-heating of sugar beet molasses
and the supplementation of the medium were investigated in order to
improve xanthan gum production. Maximum xanthan gum
production in fermentation media (9.02 g/l) was observed after 4 days
shaking incubation at 25°C and 240 rpm agitation speed. A solution
of 10% sucrose was used as a control medium. Results indicated that
the optimum period for xanthan gum production in this condition was
4 days.
Abstract: This paper presents a new sensor-based online method for generating collision-free near-optimal paths for mobile robots pursuing a moving target amidst dynamic and static obstacles. At each iteration, first the set of all collision-free directions are calculated using velocity vectors of the robot relative to each obstacle and target, forming the Directive Circle (DC), which is a novel concept. Then, a direction close to the shortest path to the target is selected from feasible directions in DC. The DC prevents the robot from being trapped in deadlocks or local minima. It is assumed that the target's velocity is known, while the speeds of dynamic obstacles, as well as the locations of static obstacles, are to be calculated online. Extensive simulations and experimental results demonstrated the efficiency of the proposed method and its success in coping with complex environments and obstacles.
Abstract: This paper presents a means for reducing the torque
variation during the revolution of a vertical-axis water turbine
(VAWaterT) by increasing the blade number. For this purpose, twodimensional
CFD analyses have been performed on a straight-bladed
Darrieus-type rotor. After describing the computational model and
the relative validation procedure, a complete campaign of
simulations, based on full RANS unsteady calculations, is proposed
for a three, four and five-bladed rotor architectures, characterized by
a NACA 0025 airfoil. For each proposed rotor configuration, flow
field characteristics are investigated at several values of tip speed
ratio, allowing a quantification of the influence of blade number on
flow geometric features and dynamic quantities, such as rotor torque
and power. Finally, torque and power curves are compared for the
three analyzed architectures, achieving a quantification of the effect
of blade number on overall rotor performance.
Abstract: This paper demonstrates the application of craziness based particle swarm optimization (CRPSO) technique for designing the 8th order low pass Infinite Impulse Response (IIR) filter. CRPSO, the much improved version of PSO, is a population based global heuristic search algorithm which finds near optimal solution in terms of a set of filter coefficients. Effectiveness of this algorithm is justified with a comparative study of some well established algorithms, namely, real coded genetic algorithm (RGA) and particle swarm optimization (PSO). Simulation results affirm that the proposed algorithm CRPSO, outperforms over its counterparts not only in terms of quality output i.e. sharpness at cut-off, pass band ripple, stop band ripple, and stop band attenuation but also in convergence speed with assured stability.
Abstract: Fructooligosaccharides derived from microbial enzyme especially from fungal sources has been received particular attention due to its beneficial effects as prebiotics and mass production. However, fungal fermentation is always cumbersome due to its broth rheology problem that will eventually affect the production of FOS. This study investigated the efficiency of immobilized cell system using rotating fibrous bed bioreactor (RFBB) in producing fructooligosaccharides (FOS). A comparative picture with respect to conventional stirred tank bioreactor (CSTB) and RFBB has been presented. To demonstrate the effect of agitation intensity and aeration rate, a laboratory-scale bioreactor 2.5 L was operated in three phases (high, medium, low) for 48 hours. Agitation speed has a great influence on P. simplicissimum fermentation for FOS production, where the volumetric FOS productivity using RFBB is increased with almost 4 fold compared to the FOS productivity in CSTB that only 0.319 g/L/h. Rate of FOS production increased up to 1.2 fold when immobilized cells system was employed at aeration rate similar to the freely suspended cells at 2.0 vvm.
Abstract: The interaction of the blade tip with the casing
boundary layer and the leakage flow may lead to a kind of cavitation
namely tip vortex cavitation. In this study, the onset of tip vortex
cavitation was experimentally investigated in an axial flow pump.
For a constant speed and a fixed angle of attack and by changing the
flow rate, the pump head, input power, output power and efficiency
were calculated and the pump characteristic curves were obtained.
The cavitation phenomenon was observed with a camera and a
stroboscope. Finally, the critical flow region, which tip vortex
cavitation might have occurred, was identified. The results show that
just by adjusting the flow rate, out of the specified region, the
possibility of occurring tip vortex cavitation, decreases to a great
extent.
Abstract: Deep and radical social reforms of the last century-s
nineties in many Eastern European countries caused changes in
Information Technology-s (IT) field. Inefficient information
technologies were rapidly replaced with forefront IT solutions, e.g.,
in Eastern European countries there is a high level penetration of
qualitative high-speed Internet. The authors have taken part in the
introduction of those changes in Latvia-s leading IT research
institute. Grounding on their experience authors in this paper offer an
IT services based model for analysis the mentioned changes- and
development processes in the higher education and research fields,
i.e., for research e-infrastructure-s development. Compare to the
international practice such services were developed in Eastern Europe
in an untraditional way, which provided swift and positive
technological changes.
Abstract: This paper presents a novel two-phase hybrid optimization algorithm with hybrid genetic operators to solve the optimal control problem of a single stage hybrid manufacturing system. The proposed hybrid real coded genetic algorithm (HRCGA) is developed in such a way that a simple real coded GA acts as a base level search, which makes a quick decision to direct the search towards the optimal region, and a local search method is next employed to do fine tuning. The hybrid genetic operators involved in the proposed algorithm improve both the quality of the solution and convergence speed. The phase–1 uses conventional real coded genetic algorithm (RCGA), while optimisation by direct search and systematic reduction of the size of search region is employed in the phase – 2. A typical numerical example of an optimal control problem with the number of jobs varying from 10 to 50 is included to illustrate the efficacy of the proposed algorithm. Several statistical analyses are done to compare the validity of the proposed algorithm with the conventional RCGA and PSO techniques. Hypothesis t – test and analysis of variance (ANOVA) test are also carried out to validate the effectiveness of the proposed algorithm. The results clearly demonstrate that the proposed algorithm not only improves the quality but also is more efficient in converging to the optimal value faster. They can outperform the conventional real coded GA (RCGA) and the efficient particle swarm optimisation (PSO) algorithm in quality of the optimal solution and also in terms of convergence to the actual optimum value.
Abstract: The wind resource in the Italian site of Lendinara
(RO) is analyzed through a systematic anemometric campaign
performed on the top of the bell tower, at an altitude of over 100 m
above the ground. Both the average wind speed and the Weibull
distribution are computed. The resulting average wind velocity is in
accordance with the numerical predictions of the Italian Wind Atlas,
confirming the accuracy of the extrapolation of wind data adopted for
the evaluation of wind potential at higher altitudes with respect to the
commonly placed measurement stations.
Abstract: In this article, a method has been offered to classify
normal and defective tiles using wavelet transform and artificial
neural networks. The proposed algorithm calculates max and min
medians as well as the standard deviation and average of detail
images obtained from wavelet filters, then comes by feature vectors
and attempts to classify the given tile using a Perceptron neural
network with a single hidden layer. In this study along with the
proposal of using median of optimum points as the basic feature and
its comparison with the rest of the statistical features in the wavelet
field, the relational advantages of Haar wavelet is investigated. This
method has been experimented on a number of various tile designs
and in average, it has been valid for over 90% of the cases. Amongst
the other advantages, high speed and low calculating load are
prominent.
Abstract: This paper presents the results of a study aimed at
establishing the temperature distribution during the welding of
magnesium alloy sheets by Pulsed Current Gas Tungsten Arc
Welding (PCGTAW) and Constant Current Gas Tungsten Arc
Welding (CCGTAW) processes. Pulsing of the GTAW welding
current influences the dimensions and solidification rate of the fused
zone, it also reduces the weld pool volume hence a narrower bead. In
this investigation, the base material considered was 2mm thin AZ 31
B magnesium alloy, which is finding use in aircraft, automobile and
high-speed train components. A finite element analysis was carried
out using ANSYS, and the results of the FEA were compared with
the experimental results. It is evident from this study that the finite
element analysis using ANSYS can be effectively used to model
PCGTAW process for finding temperature distribution.
Abstract: Installation of power compensation equipment in
some cases places additional buses into the system. Therefore, a total
number of power flow equations and voltage unknowns increase due
to additional locations of installed devices. In this circumstance, power flow calculation is more complicated. It may result in a
computational convergence problem. This paper presents a power flow calculation by using Newton-Raphson iterative method together
with the proposed load transfer technique. This concept is to eliminate additional buses by transferring installed loads at the new buses to existing two adjacent buses. Thus, the total number of power
flow equations is not changed. The overall computational speed is
expectedly shorter than that of solving the problem without applying the load transfer technique. A 15-bus test system is employed for test
to evaluate the effectiveness of the proposed load transfer technique. As a result, the total number of iteration required and execution time
is significantly reduced.
Abstract: Flour from Mucuna beans (Mucuna pruriens) were
used in producing texturized meat analogue using a single screw
extruder to monitor modifications on the proximate composition and
the functional properties at high moisture level. Response surface
methodology based on Box Behnken design at three levels of barrel
temperature (110, 120, 130°C), screw speed (100,120,140rpm) and
feed moisture (44, 47, 50%) were used in 17 runs. Regression models
describing the effect of variables on the product responses were
obtained. Descriptive profile analyses and consumer acceptability
test were carried out on optimized flavoured extruded meat analogue.
Responses were mostly affected by barrel temperature and moisture
level and to a lesser extent by screw speed. Optimization results
based on desirability concept indicated that a barrel temperature of
120.15°C, feed moisture of 47% and screw speed of 119.19 rpm
would produce meat analogue of preferable proximate composition,
functional and sensory properties which reveals consumers` likeness
for the product.