Abstract: Transition theory has been used to derive the elasticplastic
and transitional stresses. Results obtained have been discussed
numerically and depicted graphically. It is observed that the rotating
disk made of incompressible material with inclusion require higher
angular speed to yield at the internal surface as compared to disk
made of compressible material. It is seen that the radial and
circumferential stresses are maximum at the internal surface with and
without edge load (for flat disk). With the increase in thickness
parameter (k = 2, 4), the circumferential stress is maximum at the
external surface while the radial stress is maximum at the internal
surface. From the figures drawn the disk with exponentially varying
thickness (k = 2), high angular speed is required for initial yielding at
internal surface as compared to flat disk and exponentially varying
thickness for k = 4 onwards. It is concluded that the disk made of
isotropic compressible material is on the safer side of the design as
compared to disk made of isotropic incompressible material as it
requires higher percentage increase in an angular speed to become
fully plastic from its initial yielding.
Abstract: This paper presents an evaluation of the wind potential in the area of the Lagoon of Venice (Italy). A full anemometric campaign of 2 year measurements, performed by the "Osservatorio Bioclimatologico dell'Ospedale al Mare di Venezia" has been analyzed to obtain the Weibull wind speed distribution and the main wind directions. The annual energy outputs of two candidate horizontal-axis wind turbines (“Aventa AV-7 LoWind" and “Gaia Wind 133-11kW") have been estimated on the basis of the computed Weibull wind distribution, registering a better performance of the former turbine, due to a higher ratio between rotor swept area and rated power of the electric generator, determining a lower cut-in wind speed.
Abstract: The presence of cold air with the convergent
topography of the Lut valley over the valley-s sloping terrain can
generate Low Level Jets (LLJ). Moreover, the valley-parallel
pressure gradients and northerly LLJ are produced as a result of the
large-scale processes. In the numerical study the regional MM5
model was run leading to achieve an appropriate dynamical analysis
of flows in the region for summer and winter. The results of this
study show the presence of summer synoptical systems cause the
formation of north-south pressure gradients in the valley which could
be led to the blowing of winds with the velocity more than 14 ms-1
and vulnerable dust and wind storms lasting more than 120 days.
Whereas the presence of cold air masses in the region in winter,
cause the average speed of LLJs decrease. In this time downslope
flows are noticeable in creating the night LLJs.
Abstract: The paper proposes the novel design of a 3T XOR gate combining complementary CMOS with pass transistor logic. The design has been compared with earlier proposed 4T and 6T XOR gates and a significant improvement in silicon area and power-delay product has been obtained. An eight transistor full adder has been designed using the proposed three-transistor XOR gate and its performance has been investigated using 0.15um and 0.35um technologies. Compared to the earlier designed 10 transistor full adder, the proposed adder shows a significant improvement in silicon area and power delay product. The whole simulation has been carried out using HSPICE.
Abstract: In a bi-fuel diesel engine, the carburetor plays a vital
role in switching from fuel gas to petrol mode operation and viceversa.
The carburetor is the most important part of the fuel system of
a diesel engine. All diesel engines carry variable venturi mixer
carburetors. The basic operation of the carburetor mainly depends on
the restriction barrel called the venturi. When air flows through the
venturi, its speed increases and its pressure decreases. The main
challenge focuses on designing a mixing device which mixes the
supplied gas is the incoming air at an optimum ratio. In order to
surmount the identified problems, the way fuel gas and air flow in
the mixer have to be analyzed. In this case, the Computational Fluid
Dynamics or CFD approach is applied in design of the prototype
mixer. The present work is aimed at further understanding of the air
and fuel flow structure by performing CFD studies using a software
code. In this study for mixing air and gas in the condition that has
been mentioned in continuance, some mixers have been designed.
Then using of computational fluid dynamics, the optimum mixer has
been selected. The results indicated that mixer with 12 holes can
produce a homogenous mixture than those of 8-holes and 6-holes
mixer. Also the result showed that if inlet convergency was smoother
than outlet divergency, the mixture get more homogenous, the reason
of that is in increasing turbulence in outlet divergency.
Abstract: Traffic density, an indicator of traffic
conditions, is one of the most critical characteristics to
Intelligent Transport Systems (ITS). This paper investigates
recursive traffic density estimation using the information
provided from inductive loop detectors. On the basis of the
phenomenological relationship between speed and density, the
existing studies incorporate a state space model and update the
density estimate using vehicular speed observations via the
extended Kalman filter, where an approximation is made
because of the linearization of the nonlinear observation
equation. In practice, this may lead to substantial estimation
errors. This paper incorporates a suitable transformation to
deal with the nonlinear observation equation so that the
approximation is avoided when using Kalman filter to
estimate the traffic density. A numerical study is conducted. It
is shown that the developed method outperforms the existing
methods for traffic density estimation.
Abstract: The last years have seen an increasing use of image analysis techniques in the field of biomedical imaging, in particular in microscopic imaging. The basic step for most of the image analysis techniques relies on a background image free of objects of interest, whether they are cells or histological samples, to perform further analysis, such as segmentation or mosaicing. Commonly, this image consists of an empty field acquired in advance. However, many times achieving an empty field could not be feasible. Or else, this could be different from the background region of the sample really being studied, because of the interaction with the organic matter. At last, it could be expensive, for instance in case of live cell analyses. We propose a non parametric and general purpose approach where the background is built automatically stemming from a sequence of images containing even objects of interest. The amount of area, in each image, free of objects just affects the overall speed to obtain the background. Experiments with different kinds of microscopic images prove the effectiveness of our approach.
Abstract: Tourism is a phenomenon respected by the human communities since a long time ago. It has been evoloving continually based on a variety of social and economic needs and with respect to increasingly development of communication and considerable increase of tourist-s number and resulted exchange income has attained much out come such as employment for the communities. or the purpose of tourism development in this zone suitable times and locations need to be specified in the zone for the tourist-s attendance. One of the most important needs of the tourists is the knowledge of climate conditions and suitable times for sightseeing. In this survey, the climate trend condition has been identified for attending the tourists in Isfahan province using the modified tourism climate index (TCI) as well as SPSS, GIS, excel, surfer softwares. This index evoluates systematically the climate conditions for tourism affairs and activities using the monthly maximum mean parameters of daily temperature, daily mean temperature, minimum relative humidity, daily mean relative humidity, precipitation (mm), total sunny hours, wind speed and dust. The results obtaind using kendal-s correlation test show that the months January, February, March, April, May, June, July, August, September, October, November and December are significant and have an increasing trend that indicates the best condition for attending the tourists. S, P, T mean , T max and dust are estimated from 1976-2005 and do kendal-s correlation test again to see which parameter has been effective. Based on the test, we also observed on the effective parameters that the rate of dust in February, March, April, May, June, July, August, October and November is decreasing and precipitation in September and January is increasing and also the radiation rate in May and August is increasing that indicate a better condition of convenience. Maximum temperature in June is also decreasing. Isfahan province has two spring and fall peaks and the best places for tourism are in the north and western areas.
Abstract: In this paper we present a technique to speed up
ICA based on the idea of reducing the dimensionality of the data
set preserving the quality of the results. In particular we refer to
FastICA algorithm which uses the Kurtosis as statistical property
to be maximized. By performing a particular Johnson-Lindenstrauss
like projection of the data set, we find the minimum dimensionality
reduction rate ¤ü, defined as the ratio between the size k of the reduced
space and the original one d, which guarantees a narrow confidence
interval of such estimator with high confidence level. The derived
dimensionality reduction rate depends on a system control parameter
β easily computed a priori on the basis of the observations only.
Extensive simulations have been done on different sets of real world
signals. They show that actually the dimensionality reduction is very
high, it preserves the quality of the decomposition and impressively
speeds up FastICA. On the other hand, a set of signals, on which the
estimated reduction rate is greater than 1, exhibits bad decomposition
results if reduced, thus validating the reliability of the parameter β.
We are confident that our method will lead to a better approach to
real time applications.
Abstract: The controllable electrical loss which consists of the
copper loss and iron loss can be minimized by the optimal control of
the armature current vector. The control algorithm of current vector
minimizing the electrical loss is proposed and the optimal current
vector can be decided according to the operating speed and the load
conditions. The proposed control algorithm is applied to the
experimental PM motor drive system and this paper presents a
modern approach of speed control for permanent magnet
synchronous motor (PMSM) applied for Electric Vehicle using a
nonlinear control. The regulation algorithms are based on the
feedback linearization technique. The direct component of the current
is controlled to be zero which insures the maximum torque operation.
The near unity power factor operation is also achieved. More over,
among EV-s motor electric propulsion features, the energy efficiency
is a basic characteristic that is influenced by vehicle dynamics and
system architecture. For this reason, the EV dynamics are taken into
account.
Abstract: Iris localization is a very important approach in
biometric identification systems. Identification process usually is
implemented in three levels: iris localization, feature extraction, and
pattern matching finally. Accuracy of iris localization as the first step
affects all other levels and this shows the importance of iris
localization in an iris based biometric system. In this paper, we
consider Daugman iris localization method as a standard method,
propose a new method in this field and then analyze and compare the
results of them on a standard set of iris images. The proposed method
is based on the detection of circular edge of iris, and improved by
fuzzy circles and surface energy difference contexts. Implementation
of this method is so easy and compared to the other methods, have a
rather high accuracy and speed. Test results show that the accuracy of
our proposed method is about Daugman method and computation
speed of it is 10 times faster.
Abstract: Hierarchical Mobile IPv6 (HMIPv6) was designed to
support IP micro-mobility management in the Next Generation
Networks (NGN) framework. The main design behind this protocol is
the usage of Mobility Anchor Point (MAP) located at any level router
of network to support hierarchical mobility management. However,
the distance MAP selection in HMIPv6 causes MAP overloaded and
increase frequent binding update as the network grows. Therefore, to
address the issue in designing MAP selection scheme, we propose a
dynamic load control mechanism integrates with a speed detection
mechanism (DMS-DLC). From the experimental results we obtain
that the proposed scheme gives better distribution in MAP load and
increase handover speed.
Abstract: This paper presents the influence of preloading on a)
the contact tractions, b) slip levels and c) stresses at the dovetail
blade-disc interface of an aero-engine through a three-dimensional
(3D) finite element (FE) modeling and analysis. The preloading is
applied by an interference fit at the dovetail interface and the bulk
loading is applied through the rotational speed of rotor. Preloading at
the dovetail interface reduces the peak contact pressure developed
due to bulk loading up to 35%, and reduces the peak contact pressure
and stress difference between top and bottom contact edges.
Increasing the level of preloading reduces the cyclic stress amplitude
at the interface up to certain values of preload and as a consequence,
an improvement in fatigue life could be expected. Fretting damage,
due to vibration and wind milling effect during engine ground
condition, can be minimized by preloading the dovetail interface.
Abstract: In this study, the sorption of Malachite green (MG) on Hydrilla verticillata biomass, a submerged aquatic plant, was investigated in a batch system. The effects of operating parameters such as temperature, adsorbent dosage, contact time, adsorbent size, and agitation speed on the sorption of Malachite green were analyzed using response surface methodology (RSM). The proposed quadratic model for central composite design (CCD) fitted very well to the experimental data that it could be used to navigate the design space according to ANOVA results. The optimum sorption conditions were determined as temperature - 43.5oC, adsorbent dosage - 0.26g, contact time - 200min, adsorbent size - 0.205mm (65mesh), and agitation speed - 230rpm. The Langmuir and Freundlich isotherm models were applied to the equilibrium data. The maximum monolayer coverage capacity of Hydrilla verticillata biomass for MG was found to be 91.97 mg/g at an initial pH 8.0 indicating that the optimum sorption initial pH. The external and intra particle diffusion models were also applied to sorption data of Hydrilla verticillata biomass with MG, and it was found that both the external diffusion as well as intra particle diffusion contributes to the actual sorption process. The pseudo-second order kinetic model described the MG sorption process with a good fitting.
Abstract: Snow cover is an important phenomenon in
hydrology, hence modeling the snow accumulation and melting is an
important issue in places where snowmelt significantly contributes to
runoff and has significant effect on water balance. The physics-based
models are invariably distributed, with the basin disaggregated into
zones or grid cells. Satellites images provide valuable data to verify
the accuracy of spatially distributed model outputs. In this study a
spatially distributed physically based model (WetSpa) was applied to
predict snow cover and melting in the Latyan dam watershed in Iran.
Snowmelt is simulated based on an energy balance approach. The
model is applied and calibrated with one year of observed daily
precipitation, air temperature, windspeed, and daily potential
evaporation. The predicted snow-covered area is compared with
remotely sensed images (MODIS). The results show that simulated
snow cover area SCA has a good agreement with satellite image
snow cover area SCA from MODIS images. The model performance
is also tested by statistical and graphical comparison of simulated and
measured discharges entering the Latyan dam reservoir.
Abstract: Based on a long-term vegetation index dataset of NDVI and meteorological data from 68 meteorological stations in the Qinghai-Tibet plateau and their relations with major climate factors were analyzed. The results show the following: 1) The linear trends of temperature in the Qinghai-Tibet plateau indicate that the temperature in the plateau generally increased, but it rose faster in the last 20 years. 2) The most significant NDVI increase occurred in the eastern and southern plateau. However, the western and northern plateau demonstrate a decreasing trend. 3) There is a significant positive linear correlation between NDVI and temperature and a negative correlation between NDVI and mean wind speed. However, no significant statistical relationship was found between NDVI and relative humidity, precipitation or sunshine duration.4) The changes in NDVI for the plateau are driven by temperature-precipitation, but for the desert and forest areas, the relation changes to precipitation-temperature-wind velocity and wind velocity-temperature-precipitation.
Abstract: This paper is concerned with an improved algorithm
based on the piecewise-smooth Mumford and Shah (MS) functional
for an efficient and reliable segmentation. In order to speed up
convergence, an additional force, at each time step, is introduced
further to drive the evolution of the curves instead of only driven by
the extensions of the complementary functions u + and u - . In our
scheme, furthermore, the piecewise-constant MS functional is
integrated to generate the extra force based on a temporary image that
is dynamically created by computing the union of u + and u - during
segmenting. Therefore, some drawbacks of the original algorithm,
such as smaller objects generated by noise and local minimal problem
also are eliminated or improved. The resulting algorithm has been
implemented in Matlab and Visual Cµ, and demonstrated efficiently
by several cases.
Abstract: Composting is the process in which municipal solid
waste (MSW) and other organic waste materials such as biosolids
and manures are decomposed through the action of bacteria and other
microorganisms into a stable granular material which, applied to
land, as soil conditioner. Microorganisms, especially those that are
able to degrade polymeric organic material have a key role in speed
up this process. The aim of this study has been established to
isolation of microorganisms with high ability to production
extracellular enzymes for degradation of natural polymers that are
exists in MSW for decreasing time of degradation phase. Our
experimental study for isolation designed in two phases: in first
phase we isolated degrading microorganism with selected media that
consist a special natural polymer such as cellulose, starch, lipids and
etc as sole source of carbon. In second phase we selected
microorganism that had high degrading enzyme production with
enzymatic assay for seed production. However, our findings in pilot
scale have indicated that usage of this microbial consortium had high
efficiency for decreasing degradation phase.
Abstract: In this paper, 3X3 routing nodes are proposed to
provide speedup and parallel processing capability in Data Vortex
network architectures. The new design not only significantly
improves network throughput and latency, but also eliminates the
need for distributive traffic control mechanism originally embedded
among nodes and the need for nodal buffering. The cost effectiveness
is studied by a comparison study with the previously proposed 2-
input buffered networks, and considerable performance enhancement
can be achieved with similar or lower cost of hardware. Unlike
previous implementation, the network leaves small probability of
contention, therefore, the packet drop rate must be kept low for such
implementation to be feasible and attractive, and it can be achieved
with proper choice of operation conditions.
Abstract: This research were investigated, determined, and
analyzed of the climate characteristically change in the provincial
Udon Thani in the period of 60 surrounding years from 1951 to 2010
A.D. that it-s transferred to effects of climatologically data for
determining global warming. Statistically significant were not found
for the 60 years- data (R2