Abstract: An adaptive Helmholtz resonator was designed and
adapted to hydraulics. The resonator was controlled by open- and
closed-loop controls so that 20 dB attenuation of the peak-to-peak
value of the pulsating pressure was maintained. The closed-loop
control was noted to be better, albeit it was slower because of its low
pressure and temperature variation, which caused variation in the
effective bulk modulus of the hydraulic system. Low-pressure
hydraulics contains air, which affects the stiffness of the hydraulics,
and temperature variation changes the viscosity of the oil. Thus, an
open-loop control loses its efficiency if a condition such as
temperature or the amount of air changes after calibration. The
instability of the low-pressure hydraulic system reduced the
operational frequency range of the Helmholtz resonator when
compared with the results of an analytical model.
Different dampers for hydraulics are presented. Then analytical
models of a hydraulic pipe and a hydraulic pipe with a Helmholtz
resonator are presented. The analytical models are based on the wave
equation of sound pressure. Finally, control methods and the results
of experiments are presented.
Abstract: In this paper the application of neuro-fuzzy system for equalization of channel distortion is considered. The structure and operation algorithm of neuro-fuzzy equalizer are described. The use of neuro-fuzzy equalizer in digital signal transmission allows to decrease training time of parameters and decrease the complexity of the network. The simulation of neuro-fuzzy equalizer is performed. The obtained result satisfies the efficiency of application of neurofuzzy technology in channel equalization.
Abstract: In this paper, a new reverse converter for the moduli set {2n, 2n–1, 2n–1–1} is presented. We improved a previously introduced conversion algorithm for deriving an efficient hardware design for reverse converter. Hardware architecture of the proposed converter is based on carry-save adders and regular binary adders, without the requirement for modular adders. The presented design is faster than the latest introduced reverse converter for moduli set {2n, 2n–1, 2n–1–1}. Also, it has better performance than the reverse converters for the recently introduced moduli set {2n+1–1, 2n, 2n–1}
Abstract: Hepatocellular carcinoma, also called hepatoma, most
commonly appears in a patient with chronic viral hepatitis. In
patients with a higher suspicion of HCC, such as small or subtle
rising of serum enzymes levels, the best method of diagnosis
involves a CT scan of the abdomen, but only at high cost. The aim of
this study was to increase the ability of the physician to early detect
HCC, using a probabilistic neural network-based approach, in order
to save time and hospital resources.
Abstract: This current research focused on development of degradable starch based packaging film with enhanced mechanical properties. A series of low density polyethylene (LDPE)/tapioca starch compounds with various tapioca starch contents were prepared by twin screw extrusion with the addition of maleic anhydride grafted polyethylene as compatibilizer. Palm cooking oil was used as processing aid to ease the blown film process, thus, degradable film can be processed via conventional blown film machine. Studies on their characteristics, mechanical properties and biodegradation were carried out by Fourier Transform Infrared (FTIR) spectroscopy and optical properties, tensile test and exposure to fungi environment respectively. The presence of high starch contents had an adverse effect on the tensile properties of LDPE/tapioca starch blends. However, the addition of compatibilizer to the blends improved the interfacial adhesion between the two materials, hence, improved the tensile properties of the films. High content of starch amount also was found to increase the rate of biodegradability of LDPE/tapioca starch films. It can be proved by exposure of the film to fungi environment. A growth of microbes colony can be seen on the surface of LDPE/tapioca starch film indicates that the granular starch present on the surface of the polymer film is attacked by microorganisms, until most of it is assimilated as a carbon source.
Abstract: In this paper, Differential Evolution (DE) algorithm, a new promising evolutionary algorithm, is proposed to train Radial Basis Function (RBF) network related to automatic configuration of network architecture. Classification tasks on data sets: Iris, Wine, New-thyroid, and Glass are conducted to measure the performance of neural networks. Compared with a standard RBF training algorithm in Matlab neural network toolbox, DE achieves more rational architecture for RBF networks. The resulting networks hence obtain strong generalization abilities.
Abstract: The classic problem of recovering arbitrary values of
a band-limited signal from its samples has an added complication
in software radio applications; namely, the resampling calculations
inevitably fold aliases of the analog signal back into the original
bandwidth. The phenomenon is quantified by the spur-free dynamic
range. We demonstrate how a novel application of the Remez (Parks-
McClellan) algorithm permits optimal signal recovery and SFDR, far
surpassing state-of-the-art resamplers.
Abstract: Carbon nanotubes (CNTs) are attractive because of
their excellent chemical durability mechanical strength and electrical
properties. Therefore there is interest in CNTs for not only electrical
and mechanical application, but also biological and medical
application.
In this study, the dispersion power of surfactant-treated multiwalled
carbon nanotubes (MWCNTs) and their effect on the antibacterial
activity were examined. Surfactant was used sodium
dodecyl-benzenesulfonate (SDBS). UV-vis absorbance and
transmission electron microscopy(TEM) were used to characterize the
dispersion of MWCNTs in the aqueous phase, showing that the
surfactant molecules had been adsorbed onto the MWCNTs surface.
The surfactant-treated MWCNTs exhibited antimicrobial activities
to streptococcus mutans. The optical density growth curves and viable
cell number determined by the plating method suggested that the
antimicrobial activity of surfactant-treated MWCNTs was both
concentration and treatment time-dependent.
Abstract: An efficient parallel form in digital signal processor can improve the algorithm performance. The butterfly structure is an important role in fast Fourier transform (FFT), because its symmetry form is suitable for hardware implementation. Although it can perform a symmetric structure, the performance will be reduced under the data-dependent flow characteristic. Even though recent research which call as novel memory reference reduction methods (NMRRM) for FFT focus on reduce memory reference in twiddle factor, the data-dependent property still exists. In this paper, we propose a parallel-computing approach for FFT implementation on digital signal processor (DSP) which is based on data-independent property and still hold the property of low-memory reference. The proposed method combines final two steps in NMRRM FFT to perform a novel data-independent structure, besides it is very suitable for multi-operation-unit digital signal processor and dual-core system. We have applied the proposed method of radix-2 FFT algorithm in low memory reference on TI TMSC320C64x DSP. Experimental results show the method can reduce 33.8% clock cycles comparing with the NMRRM FFT implementation and keep the low-memory reference property.
Abstract: To simulate heating systems in buildings, a research oriented computer code has been developed in Sharif University of Technology in Iran where the climate, existing heating equipment in buildings, consumer behavior and their interactions are considered for simulating energy consumption in conventional systems such as heaters, radiators and fan-coils. In order to validate the computer code, the available data of five buildings was used and the computed consumed energy was compared with the estimated energy extracted from monthly bills. The initial heating system was replaced by the alternative system and the effect of this change was observed on the energy consumption. As a result, the effect of changing heating equipment on energy consumption was investigated in different climates. Changing heater to radiator renders energy conservation up to 50% in all climates and changing radiator to fan-coil decreases energy consumption in climates with cold and dry winter.
Abstract: This paper presents the design and implementation of a fully integrated transimpedance amplifier (TIA) as the analog frontend receiver for Capacitive Micromachined Ultrasound Transducers (CMUTs) for ultrasound biomicroscope imaging application. The amplifier is designed to amplify the received signals from 17.5MHz to 52.5MHz with a center frequency of 35MHz. The TIA was fabricated in GF 0.18μm 1P6M 30V high voltage process. The measurement results show that the designed amplifier can reach a transimpedance gain of 61.08dBΩ and operating frequency from 17.5MHz to 100MHz with 1VP-P output voltage under 6V power supply.
Abstract: Sorghum flour was supplemented with 15 and 30%
chickpea flour. Sorghum flour and the supplement were fermented at
35 oC for 0, 8, 16, and 24 h. Changes in pH, titrable acidity, total
soluble solids, protein content, in vitro protein digestibility and
amino acid composition were investigated during fermentation and/or
after supplementation of sorghum flour with chickpea. The pH of the
fermenting material decreased sharply with a concomitant increase in
the titrable acidity. The total soluble solids remained unchanged with
progressive fermentation time. The protein content of sorghum
cultivar was found to be 9.27 and that of chickpea was 22.47%. The
protein content of sorghum cultivar after supplementation with15 and
30% chickpea was significantly (P ≤ 0.05) increased to 11.78 and
14.55%, respectively. The protein digestibility also increased after
fermentation from 13.35 to 30.59 and 40.56% for the supplements,
respectively. Further increment in protein content and digestibility
was observed when supplemented and unsupplemented samples were
fermented for different periods of time. Cooking of fermented
samples was found to increase the protein content slightly and
decreased digestibility for both supplements. Amino acid content of
fermented and fermented and cooked supplements was determined.
Supplementation was found to increase the lysine and therionine
content. Cooking following fermentation decreased lysine,
isoleucine, valine and sulfur containg amino acids.
Abstract: User interaction components of Augmented Reality (AR) systems have to be tested with users in order to find and fix usability problems as early as possible. In this paper we will report on a user-centered design approach for AR systems following the experience acquired during the design and evaluation of a software prototype for an AR-based educational platform. In this respect we will focus on the re-design of the user task based on the results from a formative usability evaluation. The basic idea of our approach is to describe task scenarios in a tabular format, to develop a task model in a task modeling environment and then to simulate the execution.
Abstract: The experiment was performed to evaluate the effect
of GA3, 2,4-D on fruit growth and fruit quality of wax apple. The
experiment consisted of Red A, Monulla, Atu, Red B cultivars. GA3
and 2,4-D were applied at the small bud and petal fall stage.
Physiological, biochemical characters of fruit were recoded. The
result showed application of GA3, 2,4-D greatly response in
increasing fruit set for all treatment as compared to control. Fruit
weight, fruit size were increased at 10 ppm 2,4-D in ‘Red A’, ‘Red
B’, however it was also enhancing at 10 ppm GA3 in ‘Monulla’,
‘Atu’. For ‘Monulla’, ‘Atu’ fruit crack reduced by 10 ppm 2,4-D
application, but ‘Red B’, ‘Red A’ gave least fruit crack at 10 and 30
ppm GA3, respectively. ‘Monulla’, ‘Atu’ and ‘Red B’ resulted in
response well to 10 ppm GA3 on improving TSS, whereas
application of 30 ppm GA3 greatly enhancing TSS in ‘Red A’. For
‘Atu’ titratable acidity markedly reduced by 10 ppm GA3
application, but spraying with 30 ppm GA3 greatly response in
reducing titratable acidity in ‘Red A’, ‘Red B’ and ‘Monulla’. It was
concluded that GA3, 2,4-D can be an effective tool to enhancing fruit
set, fruit growth as well as improving fruit quality of wax apple.
Abstract: Prolonged immobilization leads to significant
weakness and atrophy of the skeletal muscle and can also impair the
recovery of muscle strength following injury. Therefore, it is
important to minimize the period under immobilization and accelerate
the return to normal activity. This study examined the effects of heat
treatment and rest-inserted exercise on the muscle activity of the lower
limb during knee flexion/extension. Twelve healthy subjects were
assigned to 4 groups that included: (1) heat treatment + rest-inserted
exercise; (2) heat + continuous exercise; (3) no heat + rest-inserted
exercise; and (4) no heat + continuous exercise. Heat treatment was
applied for 15 mins prior to exercise. Continuous exercise groups
performed knee flexion/extension at 0.5 Hz for 300 cycles without rest
whereas rest-inserted exercise groups performed the same exercise but
with 2 mins rest inserted every 60 cycles of continuous exercise.
Changes in the rectus femoris and hamstring muscle activities were
assessed at 0, 1, and 2 weeks of treatment by measuring the
electromyography signals of isokinetic maximum voluntary
contraction. Significant increases in both the rectus femoris and
hamstring muscles were observed after 2 weeks of treatment only
when both heat treatment and rest-inserted exercise were performed.
These results suggest that combination of various treatment techniques,
such as heat treatment and rest-inserted exercise, may expedite the
recovery of muscle strength following immobilization.
Abstract: CFD simulations are carried out in arterial stenoses
with 48 % areal occlusion. Non-newtonian fluid model is selected for
the blood flow as the same problem has been solved before with
Newtonian fluid model. Studies on flow resistance with the presence
of surface irregularities are carried out. Investigations are also
performed on the pressure drop at various Reynolds numbers. The
present study revealed that the pressure drop across a stenosed artery
is practically unaffected by surface irregularities at low Reynolds
numbers, while flow features are observed and discussed at higher
Reynolds numbers.
Abstract: There are many researches to detect collision between real object and virtual object in 3D space. In general, these techniques are need to huge computing power. So, many research and study are constructed by using cloud computing, network computing, and distribute computing. As a reason of these, this paper proposed a novel fast 3D collision detection algorithm between real and virtual object using 2D intersection area. Proposed algorithm uses 4 multiple cameras and coarse-and-fine method to improve accuracy and speed performance of collision detection. In the coarse step, this system examines the intersection area between real and virtual object silhouettes from all camera views. The result of this step is the index of virtual sensors which has a possibility of collision in 3D space. To decide collision accurately, at the fine step, this system examines the collision detection in 3D space by using the visual hull algorithm. Performance of the algorithm is verified by comparing with existing algorithm. We believe proposed algorithm help many other research, study and application fields such as HCI, augmented reality, intelligent space, and so on.
Abstract: Recently, the improvements in processing performance
of a computer and in high speed communication of an optical fiber
have been achieved, so that the amount of data which are processed
by a computer and flowed on a network has been increasing greatly.
However, in a client-server system, since the server receives and
processes the amount of data from the clients through the network, a
load on the server is increasing. Thus, there are needed to introduce
a server with high processing ability and to have a line with high
bandwidth. In this paper, concerning to P2P networks to resolve the
load on a specific server, a criterion called an Indexed-Priority Metric
is proposed and its performance is evaluated. The proposed metric is
to allocate some files to each node. As a result, the load on a specific
server can distribute them to each node equally well. A P2P file
sharing system using the proposed metric is implemented. Simulation
results show that the proposed metric can make it distribute files on
the specific server.
Abstract: Efficient utilization of existing water is a pressing
need for Pakistan. Due to rising population, reduction in present
storage capacity and poor delivery efficiency of 30 to 40% from
canal. A study to evaluate an irrigation system in the cotton-wheat
zone of Pakistan, after the watercourse lining was conducted. The
study is made on the basis of cropping pattern and salinity to evaluate
the system. This study employed an index-based approach of using
Geographic information system with field data. The satellite images
of different years were use to examine the effective area. Several
combinations of the ratio of signals received in different spectral
bands were used for development of this index. Near Infrared and
Thermal IR spectral bands proved to be most effective as this
combination helped easy detection of salt affected area and cropping
pattern of the study area. Result showed that 9.97% area under
salinity in 1992, 9.17% in 2000 and it left 2.29% in year 2005.
Similarly in 1992, 45% area is under vegetation it improves to 56%
and 65% in 2000 and 2005 respectively. On the basis of these results
evaluation is done 30% performance is increase after the watercourse
improvement.
Abstract: Along with forward supply chain organization needs
to consider the impact of reverse logistics due to its economic
advantage, social awareness and strict legislations. In this paper, we
develop a system dynamics framework for a closed-loop supply
chain with fuzzy demand and fuzzy collection rate by incorporating
product exchange policy in forward channel and various recovery
options in reverse channel. The uncertainty issues associated with
acquisition and collection of used product have been quantified using
possibility measures. In the simulation study, we analyze order
variation at both retailer and distributor level and compare bullwhip
effects of different logistics participants over time between the
traditional forward supply chain and the closed-loop supply chain.
Our results suggest that the integration of reverse logistics can reduce
order variation and bullwhip effect of a closed-loop system. Finally,
sensitivity analysis is performed to examine the impact of various
parameters on recovery process and bullwhip effect.