Abstract: Vortices can develop in intakes of turbojet and turbo
fan aero engines during high power operation in the vicinity of solid
surfaces. These vortices can cause catastrophic damage to the engine.
The factors determining the formation of the vortex include both
geometric dimensions as well as flow parameters. It was shown that
the threshold at which the vortex forms or disappears is also
dependent on the initial flow condition (i.e. whether a vortex forms
after stabilised non vortex flow or vice-versa). A computational fluid
dynamics study was conducted to determine the difference in
thresholds between the two conditions. This is the first reported
numerical investigation of the “memory effect". The numerical
results reproduce the phenomenon reported in previous experimental
studies and additional factors, which had not been previously studied,
were investigated. They are the rate at which ambient velocity
changes and the initial value of ambient velocity. The former was
found to cause a shift in the threshold but not the later. It was also
found that the varying condition thresholds are not symmetrical about
the neutral threshold. The vortex to no vortex threshold lie slightly
further away from the neutral threshold compared to the no vortex to
vortex threshold. The results suggests that experimental investigation
of vortex formation threshold performed either in vortex to no vortex
conditions, or vice versa, solely may introduce mis-predictions
greater than 10%.
Abstract: In this paper developed and realized absolutely new
algorithm for solving three-dimensional Poisson equation. This
equation used in research of turbulent mixing, computational fluid
dynamics, atmospheric front, and ocean flows and so on. Moreover in
the view of rising productivity of difficult calculation there was
applied the most up-to-date and the most effective parallel
programming technology - MPI in combination with OpenMP
direction, that allows to realize problems with very large data
content. Resulted products can be used in solving of important
applications and fundamental problems in mathematics and physics.
Abstract: The present paper was concerned primarily with the
analysis, simulation of the air flow and thermal patterns in a lecture
room. The paper is devoted to numerically investigate the influence
of location and number of ventilation and air conditioning supply and
extracts openings on air flow properties in a lecture room. The work
focuses on air flow patterns, thermal behaviour in lecture room where
large number of students. The effectiveness of an air flow system is
commonly assessed by the successful removal of sensible and latent
loads from occupants with additional of attaining air pollutant at a
prescribed level to attain the human thermal comfort conditions and
to improve the indoor air quality; this is the main target during the
present paper. The study is carried out using computational fluid
dynamics (CFD) simulation techniques as embedded in the
commercially available CFD code (FLUENT 6.2). The CFD
modelling techniques solved the continuity, momentum and energy
conservation equations in addition to standard k – ε model equations
for turbulence closure.
Throughout the investigations, numerical validation is carried out by
way of comparisons of numerical and experimental results. Good
agreement is found among both predictions.
Abstract: CFD simulations are carried out in arterial stenoses
with 48 % areal occlusion. Non-newtonian fluid model is selected for
the blood flow as the same problem has been solved before with
Newtonian fluid model. Studies on flow resistance with the presence
of surface irregularities are carried out. Investigations are also
performed on the pressure drop at various Reynolds numbers. The
present study revealed that the pressure drop across a stenosed artery
is practically unaffected by surface irregularities at low Reynolds
numbers, while flow features are observed and discussed at higher
Reynolds numbers.
Abstract: In a bi-fuel diesel engine, the carburetor plays a vital
role in switching from fuel gas to petrol mode operation and viceversa.
The carburetor is the most important part of the fuel system of
a diesel engine. All diesel engines carry variable venturi mixer
carburetors. The basic operation of the carburetor mainly depends on
the restriction barrel called the venturi. When air flows through the
venturi, its speed increases and its pressure decreases. The main
challenge focuses on designing a mixing device which mixes the
supplied gas is the incoming air at an optimum ratio. In order to
surmount the identified problems, the way fuel gas and air flow in
the mixer have to be analyzed. In this case, the Computational Fluid
Dynamics or CFD approach is applied in design of the prototype
mixer. The present work is aimed at further understanding of the air
and fuel flow structure by performing CFD studies using a software
code. In this study for mixing air and gas in the condition that has
been mentioned in continuance, some mixers have been designed.
Then using of computational fluid dynamics, the optimum mixer has
been selected. The results indicated that mixer with 12 holes can
produce a homogenous mixture than those of 8-holes and 6-holes
mixer. Also the result showed that if inlet convergency was smoother
than outlet divergency, the mixture get more homogenous, the reason
of that is in increasing turbulence in outlet divergency.