Abstract: Samples of CoFe2-xCrxO4 where x varies from 0.0 to 0.5 were prepared by co-precipitation route. These samples were sintered at 750°C for 2 hours. These particles were characterized by X-ray diffraction (XRD) at room temperature. The FCC spinel structure was confirmed by XRD patterns of the samples. The crystallite sizes of these particles were calculated from the most intense peak by Scherrer formula. The crystallite sizes lie in the range of 37-60 nm. The lattice parameter was found decreasing upon substitution of Cr. DC electrical resistivity was measured as a function of temperature. The room temperature thermoelectric power was measured for the prepared samples. The magnitude of Seebeck coefficient depends on the composition and resistivity of the samples.
Abstract: The goal of this work is to improve the efficiency and the reliability of the automatic artifact rejection, in particular from the Electroencephalographic (EEG) recordings. Artifact rejection is a key topic in signal processing. The artifacts are unwelcome signals that may occur during the signal acquisition and that may alter the analysis of the signals themselves. A technique for the automatic artifact rejection, based on the Independent Component Analysis (ICA) for the artifact extraction and on some high order statistics such as kurtosis and Shannon-s entropy, was proposed some years ago in literature. In this paper we enhance this technique introducing the Renyi-s entropy. The performance of our method was tested exploiting the Independent Component scalp maps and it was compared to the performance of the method in literature and it showed to outperform it.
Abstract: In ubiqutious healthcare environment, user's health data are transfered to the remote healthcare server by the user's wearable system or mobile phone. These collected user's health data should be managed and analyzed in the healthcare server, so that care giver or user can monitor user's physiological state. In this paper, we designed and developed the intelligent Healthcare Server to manage the user's health data using CDSS and ontology. Our system can analyze user's health data semantically using CDSS and ontology, and report the result of user's physiological raw data to the user and care giver.
Abstract: The aim of this paper is to explore the security issues
that significantly affect the performance of Mobile Adhoc Networks
(MANET)and limit the services provided to their intended users. The
MANETs are more vulnerable to Distributed Denial of Service
attacks (DDoS) because of their properties like shared medium,
dynamic topologies etc. A DDoS attack is a coordinated attempt
made by malicious users to flood the victim network with the large
amount of data such that the resources of the victim network are
exhausted resulting in the deterioration of the network performance.
This paper highlights the effects of different types of DDoS attacks
in MANETs and categorizes them according to their behavior.
Abstract: Recently, a growing interest has emerged on the
development of new and efficient energy sources, due to the inevitable extinction of the nonrenewable energy reserves. One of
these alternative sources which has a great potential and sustainability to meet up the energy demand is biomass energy. This
significant energy source can be utilized with various energy
conversion technologies, one of which is biomass gasification in
supercritical water.
Water, being the most important solvent in nature, has very important characteristics as a reaction solvent under supercritical
circumstances. At temperatures above its critical point (374.8oC and
22.1 MPa), water becomes more acidic and its diffusivity increases.
Working with water at high temperatures increases the thermal
reaction rate, which in consequence leads to a better dissolving of the
organic matters and a fast reaction with oxygen. Hence, supercritical water offers a control mechanism depending on solubility, excellent
transport properties based on its high diffusion ability and new reaction possibilities for hydrolysis or oxidation.
In this study the gasification of a real biomass, namely olive mill
wastewater (OMW), in supercritical water is investigated with the
use of Pt/Al2O3 and Ni/Al2O3 catalysts. OMW is a by-product
obtained during olive oil production, which has a complex nature
characterized by a high content of organic compounds and
polyphenols. These properties impose OMW a significant pollution
potential, but at the same time, the high content of organics makes
OMW a desirable biomass candidate for energy production.
All of the catalytic gasification experiments were made with five
different reaction temperatures (400, 450, 500, 550 and 600°C),
under a constant pressure of 25 MPa. For the experiments conducted
with Ni/Al2O3 catalyst, the effect of five reaction times (30, 60, 90,
120 and 150 s) was investigated. However, procuring that similar
gasification efficiencies could be obtained at shorter times, the experiments were made by using different reaction times (10, 15, 20,
25 and 30 s) for the case of Pt/Al2O3 catalyst. Through these experiments, the effects of temperature, time and catalyst type on the
gasification yields and treatment efficiencies were investigated.
Abstract: To investigate effect of salt stress on Chlorophyll
fluorescence four cultivars (fong,star,chamran and kharchia) of wheat
(Triticum aestivum) plants subjected to salinity levels ( control,8,12
and 16 dsm-1 ) from one week after emergence to the end of stem
elongation under greenhouse condition . results showed that quantum
yield of photosystem II from light adopted leaves (ΦPSII),
Photochemical quenching (qP) ,quantum yield of dark adopted leaves
(fv/fm) and non photochemical quenching (NPq) were affected by
salt stress . Salinity levels affected photosynthetic rate. Star and fong
cultivars showed minimum and maximum levels of photosynthetic
rate in respectively. Minimum photosynthetic rate differences
between levels of salinity were shown in Kharchia. Shoot dry matter
of all cultivars decreased by increasing salinity levels. Results
showed that non photochemical quenching by salinity levels attribute
to the decreases in shoot dry matter.
Abstract: This paper proposes a technique to protect against
email bombing. The technique employs a statistical approach, Naïve
Bayes (NB), and Neural Networks to show that it is possible to
differentiate between good and bad traffic to protect against email
bombing attacks. Neural networks and Naïve Bayes can be trained
by utilizing many email messages that include both input and output
data for legitimate and non-legitimate emails. The input to the model
includes the contents of the body of the messages, the subject, and
the headers. This information will be used to determine if the email
is normal or an attack email. Preliminary tests suggest that Naïve
Bayes can be trained to produce an accurate response to confirm
which email represents an attack.
Abstract: In this work Artificial Intelligence (AI) techniques like Fuzzy logic, Genetic Algorithms and Particle Swarm Optimization have been used to improve the performance of the Automatic Generation Control (AGC) system. Instead of applying Genetic Algorithms and Particle swarm optimization independently for optimizing the parameters of the conventional AGC with PI controller, an intelligent tuned Fuzzy logic controller (acting as the secondary controller in the AGC system) has been designed. The controller gives an improved dynamic performance for both hydrothermal and thermal-thermal power systems under a variety of operating conditions.
Abstract: In the real application of active control systems to
mitigate the response of structures subjected to sever external
excitations such as earthquake and wind induced vibrations, since the
capacity of actuators is limited then the actuators saturate. Hence, in
designing controllers for linear and nonlinear structures under sever
earthquakes, the actuator saturation should be considered as a
constraint. In this paper optimal design of active controllers for
nonlinear structures by considering the actuator saturation has been
studied. To this end a method has been proposed based on defining
an optimization problem which considers the minimizing of the
maximum displacement of the structure as objective when a limited
capacity for actuator has been used as a constraint in optimization
problem. To evaluate the effectiveness of the proposed method, a
single degree of freedom (SDF) structure with a bilinear hysteretic
behavior has been simulated under a white noise ground acceleration
of different amplitudes. Active tendon control mechanism, comprised
of pre-stressed tendons and an actuator, and extended nonlinear
Newmark method based instantaneous optimal control algorithm
have been used as active control mechanism and algorithm. To
enhance the efficiency of the controllers, the weights corresponding
to displacement, velocity, acceleration and control force in the
performance index have been found by using the Distributed Genetic
Algorithm (DGA). According to the results it has been concluded
that the proposed method has been effective in considering the
actuator saturation in designing optimal controllers for nonlinear
frames. Also it has been shown that the actuator capacity and the
average value of required control force are two important factors in
designing nonlinear controllers for considering the actuator
saturation.
Abstract: The successful use of CDMA technology is based on
the construction of large families of encoding sequences with good
correlation properties. This paper discusses PN sequence generation
based on Residue Arithmetic with an effort to improve the performance
of existing interference-limited CDMA technology for mobile
cellular systems. All spreading codes with residual number system
proposed earlier did not consider external interferences, multipath
propagation, Doppler effect etc. In literature the use of residual
arithmetic in DS-CDMA was restricted to encoding of already spread
sequence; where spreading of sequence is done by some existing
techniques. The novelty of this paper is the use of residual number
system in generation of the PN sequences which is used to spread
the message signal. The significance of cross-correlation factor in
alleviating multi-access interference is also discussed. The RNS based
PN sequence has superior performance than most of the existing
codes that are widely used in DS-CDMA applications. Simulation
results suggest that the performance of the proposed system is
superior to many existing systems.
Abstract: Significant changes in oil and gas drilling have
emphasized the need to verify the integrity and reliability of drill
stem components. Defects are inevitable in cast components,
regardless of application; but if these defects go undetected, any
severe defect could cause down-hole failure.
One such defect is shrinkage porosity. Castings with lower level
shrinkage porosity (CB levels 1 and 2) have scattered pores and do
not occupy large volumes; so pressure testing and helium leak testing
(HLT) are sufficient for qualifying the castings. However, castings
with shrinkage porosity of CB level 3 and higher, behave erratically
under pressure testing and HLT making these techniques insufficient
for evaluating the castings- integrity.
This paper presents a case study to highlight how the radiography
technique is much more effective than pressure testing and HLT.
Abstract: Many medical devices are driven by motor pumps. Some researchers reported that the vibration mainly affected medical devices using a motor pump. The purpose of this study was to examine the effect of stiffness and damping coefficient in a 3-dimensional (3D) model of a motor pump and spring. In the present paper, experimental and mathematical tests for the moments of inertia of the 3D model and the material properties were investigated by an INSTRON machine. The response surfaces could be generated by using 3D multi-body analysis and the design of experiment method. It showed that differences in contours of the response surface were clearly found for the particular area. Displacement of the center of the motor pump was decreased at K≈2000 N/M, C≈12.5 N-sec/M. However, the frequency was increased at K≈2000 N/M, C≈15 N-sec/M. In this study, this study suggested experimental technique for vibration reduction for a motor pump in medical device. The combined method suggested in this study will greatly contribute to design of medical devices concerning vibration and noise intervention.
Abstract: Due to the non- intuitive nature of Quantum
algorithms, it becomes difficult for a classically trained person to
efficiently construct new ones. So rather than designing new
algorithms manually, lately, Genetic algorithms (GA) are being
implemented for this purpose. GA is a technique to automatically
solve a problem using principles of Darwinian evolution. This has
been implemented to explore the possibility of evolving an n-qubit
circuit when the circuit matrix has been provided using a set of
single, two and three qubit gates. Using a variable length population
and universal stochastic selection procedure, a number of possible
solution circuits, with different number of gates can be obtained for
the same input matrix during different runs of GA. The given
algorithm has also been successfully implemented to obtain two and
three qubit Boolean circuits using Quantum gates. The results
demonstrate the effectiveness of the GA procedure even when the
search spaces are large.
Abstract: Nowadays over-consumption of fossil energy in
buildings especially in residential buildings and also considering the
increase in populations, the crisis of energy shortage in a near future
is predictable. The recent performance of developed countries in
construction with the aim of decreasing fossil energies shows that
these countries have understood the incoming crisis and has taken
reasonable and basic actions in this regard. However, Iranian
architecture, with several thousands years of history, has acquired
and executed invaluable experiences in designing, adapting and
coordinating with the nature.
Architectural studies during the recent decades show that imitating
modern western architecture results in high energy wastage beside
the fact that it not reasonably adaptable and corresponded with the
habits and customs of people unlike the architecture in the past which
was compatible and adaptable with the climatic conditions and this
necessitates optimal using of renewable energies more than ever. This
paper studies problems of design, execution and living in today's
houses and reviews the characteristics of climatic elements paying
special attention to the performance of trombe wall and solar
greenhouse in traditional houses and offers some suggestions for
combining these two elements and a climatic strategy.
Abstract: In the present research, steam cracking of two types of
feedstocks i.e., naphtha and ethane is simulated for Pyrocrack1-1 and
2/2 coil configurations considering two key parameters of coil outlet
temperature (COT) and coil capacity using a radical based kinetic
model. The computer model is confirmed using the industrial data
obtained from Amirkabir Petrochemical Complex. The results are in
good agreement with performance data for naphtha cracking in a
wide range of severity (0.4-0.7), and for ethane cracking on various
conversions (50-70). It was found that Pyrocrack2-2 coil type is an
appropriate choice for steam cracking of ethane at reasonable
ethylene yield while resulting in much lower tube wall temperature
while Pyrocrack1-1 coil type is a proper selection for liquid
feedstocks i.e. naphtha. It can be used for cracking of liquid
feedstocks at optimal ethylene yield whereas not exceeding the
allowable maximum tube temperature.
Abstract: Lurking behavior is common in information-seeking oriented communities. Transferring users with lurking behavior to be contributors can assist virtual communities to obtain competitive advantages. Based on the ecological cognition framework, this study proposes a model to examine the antecedents of lurking behavior in information-seeking oriented virtual communities. This study argues desire for emotional support, desire for information support, desire for performance-approach, desire for performance -avoidance, desire for mastery-approach, desire for mastery-avoidance, desire for ability trust, desire for benevolence trust, and desire for integrity trust effect on lurking behavior. This study offers an approach to understanding the determinants of lurking behavior in online contexts.
Abstract: We present a white LED-based optical wireless
communication systems for indoor ubiquitous sensor networks. Each
sensor node could access to the server through the PLC (Power Line
Communication)-Ethernet interface. The proposed system offers a
full-duplex wireless link by using different wavelengths to reduce the
inter-symbol interference between uplink and downlink. Through the
1-to-n optical wireless sensor network and PLC modem, the mobile
terminals send a temperature data to server. The data transmission
speed and distance are 115.2kbps and about 60cm, respectively.
Abstract: In this study, we used a two-stage process and
potassium hydroxide (KOH) to transform waste biomass (rice straw)
into activated carbon and then evaluated the adsorption capacity of the
waste for removing carbofuran from an aqueous solution. Activated
carbon was fast and effective for the removal of carbofuran because of
its high surface area. The native and carbofuran-loaded adsorbents
were characterized by elemental analysis. Different adsorption
parameters, such as the initial carbofuran concentration, contact time,
temperature and pH for carbofuran adsorption, were studied using a
batch system. This study demonstrates that rice straw can be very
effective in the adsorption of carbofuran from bodies of water.
Abstract: Biochemical Oxygen Demand (BOD) is a measure of
the oxygen used in bacteria mediated oxidation of organic substances
in water and wastewater. Theoretically an infinite time is required for
complete biochemical oxidation of organic matter, but the
measurement is made over 5-days at 20 0C or 3-days at 27 0C test
period with or without dilution. Researchers have worked to further
reduce the time of measurement.
The objective of this paper is to review advancement made in
BOD measurement primarily to minimize the time and negate the
measurement difficulties. Survey of literature review in four such
techniques namely BOD-BARTTM, Biosensors, Ferricyanidemediated
approach, luminous bacterial immobilized chip method.
Basic principle, method of determination, data validation and their
advantage and disadvantages have been incorporated of each of the
methods.
In the BOD-BARTTM method the time lag is calculated for the
system to change from oxidative to reductive state. BIOSENSORS
are the biological sensing element with a transducer which produces
a signal proportional to the analyte concentration. Microbial species
has its metabolic deficiencies. Co-immobilization of bacteria using
sol-gel biosensor increases the range of substrate. In ferricyanidemediated
approach, ferricyanide has been used as e-acceptor instead
of oxygen. In Luminous bacterial cells-immobilized chip method,
bacterial bioluminescence which is caused by lux genes was
observed. Physiological responses is measured and correlated to
BOD due to reduction or emission.
There is a scope to further probe into the rapid estimation of BOD.
Abstract: Arthrobacter viscosus biomass was used for Cr(VI)
biosorption. The effect of pH on Cr(VI) reduction and removal from
aqueous solution was studied in the range of 1-4. The Cr(VI) removal
involves both redox reaction and adsorption of metal ions on biomass
surface. The removal rate of Cr(VI) was enhanced by very acid
conditions, while higher solution pH values favored the removal of
total chromium. The best removal efficiency and uptake were
reached at pH 4, 72.5 % and 12.6 mgCr/gbiomass, respectively.