Abstract: This paper presents a method to estimate load profile
in a multiple power flow solutions for every minutes in 24 hours per
day. A method to calculate multiple solutions of non linear profile is
introduced. The Power System Simulation/Engineering (PSS®E) and
python has been used to solve the load power flow. The result of this
power flow solutions has been used to estimate the load profiles for
each load at buses using Independent Component Analysis (ICA)
without any knowledge of parameter and network topology of the
systems. The proposed algorithm is tested with IEEE 69 test bus
system represents for distribution part and the method of ICA has
been programmed in MATLAB R2012b version. Simulation results
and errors of estimations are discussed in this paper.
Abstract: A new nonlinear PID controller and its stability
analysis are presented in this paper. A nonlinear function is deduced
from the similarities between the control effort and the electric-field
effect of a capacitor. The conventional linear PID controller can be
modified into a nonlinear one by this function. To analyze the stability
of the nonlinear PID controlled system, an idea of energy equivalence
is adapted to avoid the conservativeness which is usually arisen from
some traditional theorems and Criterions. The energy equivalence is
naturally related with the conceptions of Passivity and T-Passivity. As
a result, an engineering guideline for the parameter design of the
nonlinear PID controller is obtained. An inverted pendulum system is
tested to verify the nonlinear PID control scheme.
Abstract: Increasing concerns over climate change have limited
the liberal usage of available energy technology options. India faces
a formidable challenge to meet its energy needs and provide adequate
energy of desired quality in various forms to users in sustainable
manner at reasonable costs. In this paper, work carried out with an
objective to study the role of various energy technology options
under different scenarios namely base line scenario, high nuclear
scenario, high renewable scenario, low growth and high growth rate
scenario. The study has been carried out using Model for Energy
Supply Strategy Alternatives and their General Environmental
Impacts (MESSAGE) model which evaluates the alternative energy
supply strategies with user defined constraints on fuel availability,
environmental regulations etc. The projected electricity demand, at
the end of study period i.e. 2035 is 500490 MWYr. The model
predicted the share of the demand by Thermal: 428170 MWYr,
Hydro: 40320 MWYr, Nuclear: 14000 MWYr, Wind: 18000 MWYr
in the base line scenario. Coal remains the dominant fuel for
production of electricity during the study period. However, the
import dependency of coal increased during the study period. In
baseline scenario the cumulative carbon dioxide emissions upto 2035
are about 11,000 million tones of CO2. In the scenario of high nuclear
capacity the carbon dioxide emissions reduced by 10 % when nuclear
energy share increased to 9 % compared to 3 % in baseline scenario.
Similarly aggressive use of renewables reduces 4 % of carbon
dioxide emissions.
Abstract: In this paper a numerical simulation of electric and
hydrodynamic fields distribution in an electrofilter for dielectric
liquids cell is made. The simulation is made with the purpose to
determine the trajectory of particles that moves under the action of
external force in an electric and hydrodynamic field created inside of
an electrofilter for dielectric liquids. Particle trajectory is analyzed
for a dielectric liquid-solid particles suspension.
Abstract: In this work, an organic compound 5,10,15,20-
Tetrakis(3,5-di-tertbutylphenyl)porphyrinatocopper(II) (TDTBPPCu)
is studied as an active material for thin film electronic devices. To
investigate the electrical properties of TDTBPPCu, junction of
TDTBPPCu with heavily doped n-Si and Al is fabricated.
TDTBPPCu film was sandwiched between Al and n-Si electrodes.
Various electrical parameters of TDTBPPCu are determined. The
current-voltage characteristics of the junction are nonlinear,
asymmetric and show rectification behavior, which gives the clue of
formation of depletion region. This behavior indicates the potential
of TDTBPPCu for electronics applications. The current-voltage and
capacitance-voltage techniques are used to find the different
electronic parameters.
Abstract: The reluctance motor is an electric motor in which
torque is produced by the tendency of its moveable part to move to a
position where the inductance of the excited winding is maximized.
In this paper switched reluctance motors (SRMs) with two different
configurations(3-phase SRM with 4rotor poles and 6 stator poles, 4-
phase SRM with 6rotor poles and 8 stator poles) is designed by
RMxprt, and performance of them is analyzed. Efficiency and torque
of SRM for different configurations in full-load condition have been
presented. The results indicate that with correct choosing of motor
applications, maximum efficiency can be found.
Abstract: Today global warming, climate change and energy supply are of greater concern as it is widely realized that the planet earth does not provide an infinite capacity for absorbing human industrialization in the 21st century. The aim of this paper is to analyze upstream and downstream electricity production in selected case studies: a coal power plant, a pump system and a microwave oven covering and consumption to explore the position of energy efficiency in engineering sustainability. Collectively, the analysis presents energy efficiency as a major pathway towards sustainability that requires an inclusive and a holistic supply chain response in the engineering design process.
Abstract: Martensitic stainless steels have been extensively used for their good corrosion resistance and better mechanical properties. Heat treatment was suggested as one of the most excellent ways to this regard; hence, it affects the microstructure, mechanical and corrosion properties of the steel. In the current research work the microstructural changes and corrosion behavior in an AISI 420A stainless steel exposed to temperatures in the 980-1035oC range were investigated. The heat treatment is carried out in vacuum furnace within the said temperature range. The quenching of the samples was carried out in oil, brine and water media. The formation and stability of passive film was studied by Open Circuit Potential, Potentiodynamic polarization and Electrochemical Scratch Tests. The Electrochemical Impedance Spectroscopy results simulated with Equivalent Electrical Circuit suggested bilayer structure of outer porous and inner barrier oxide films. The quantitative data showed thick inner barrier oxide film retarded electrochemical reactions. Micrographs of the quenched samples showed sigma and chromium carbide phases which prove the corrosion resistance of steel alloy.
Abstract: One of the main environmental problems which affect extensive areas in the world is soil salinity. Traditional data collection methods are neither enough for considering this important environmental problem nor accurate for soil studies. Remote sensing data could overcome most of these problems. Although satellite images are commonly used for these studies, however there are still needs to find the best calibration between the data and real situations in each specified area. Neyshaboor area, North East of Iran was selected as a field study of this research. Landsat satellite images for this area were used in order to prepare suitable learning samples for processing and classifying the images. 300 locations were selected randomly in the area to collect soil samples and finally 273 locations were reselected for further laboratory works and image processing analysis. Electrical conductivity of all samples was measured. Six reflective bands of ETM+ satellite images taken from the study area in 2002 were used for soil salinity classification. The classification was carried out using common algorithms based on the best composition bands. The results showed that the reflective bands 7, 3, 4 and 1 are the best band composition for preparing the color composite images. We also found out, that hybrid classification is a suitable method for identifying and delineation of different salinity classes in the area.
Abstract: The analytical solution of functionally graded
piezoelectric hollow cylinder which is under radial electric potential
and non-axisymmetric thermo-mechanical loads, are presented in this
paper. Using complex Fourier series and estimation of power law for
variations of material characterizations through the thickness, the
electro thermo mechanical behavior of the FGPM cylinder is
obtained. The stress and displacement distributions and the effect of
electric potential field on the cylinder behavior are also presented and
some applicable results are offered at the end of the paper.
Abstract: Condition monitoring of electrical power equipment
has attracted considerable attention for many years. The aim of this
paper is to use Labview with Fuzzy Logic controller to build a
simulation system to diagnose transformer faults and monitor its
condition. The front panel of the system was designed using
LabVIEW to enable computer to act as customer-designed
instrument. The dissolved gas-in-oil analysis (DGA) method was
used as technique for oil type transformer diagnosis; meanwhile
terminal voltages and currents analysis method was used for dry type
transformer. Fuzzy Logic was used as expert system that assesses all
information keyed in at the front panel to diagnose and predict the
condition of the transformer. The outcome of the Fuzzy Logic
interpretation will be displayed at front panel of LabVIEW to show
the user the conditions of the transformer at any time.
Abstract: Permanent rivers are the main sources of renewable
water supply for the croplands under the irrigation and drainage
schemes. They are also the major source of sediment loads transport
into the storage reservoirs of the hydro-electrical dams, diversion
weirs and regulating dams. Sedimentation process results from soil
erosion which is related to poor watershed management and human
intervention ion in the hydraulic regime of the rivers. These could
change the hydraulic behavior and as such, leads to riverbed and river
bank scouring, the consequences of which would be sediment load
transport into the dams and therefore reducing the flow discharge in
water intakes. The present paper investigate sedimentation process
by varying the Manning coefficient "n" by using the SHARC
software along the watercourse in the Dez River. Results indicated
that the optimum "n" within that river range is 0.0315 at which
quantity minimum sediment loads are transported into the Eastern
intake. Comparison of the model results with those obtained by those
from the SSIIM software within the same river reach showed a very
close proximity between them. This suggests a relative accuracy with
which the model can simulate the hydraulic flow characteristics and
therefore its suitability as a powerful analytical tool for project
feasibility studies and project implementation.
Abstract: In recent years there has been renewal of interest in the
relation between Green IT and Cloud Computing. The growing use of
computers in cloud platform has caused marked energy consumption,
putting negative pressure on electricity cost of cloud data center. This
paper proposes an effective mechanism to reduce energy utilization in
cloud computing environments. We present initial work on the
integration of resource and power management that aims at reducing
power consumption. Our mechanism relies on recalling virtualization
services dynamically according to user-s virtualization request and
temporarily shutting down the physical machines after finish in order
to conserve energy. Given the estimated energy consumption, this
proposed effort has the potential to positively impact power
consumption. The results from the experiment concluded that energy
indeed can be saved by powering off the idling physical machines in
cloud platforms.
Abstract: The world's population continues to grow at a quarter of a million people per day, increasing the consumption of energy. This has made the world to face the problem of energy crisis now days. In response to the energy crisis, the principles of renewable energy gained popularity. There are much advancement made in developing the wind and solar energy farms across the world. These energy farms are not enough to meet the energy requirement of world. This has attracted investors to procure new sources of energy to be substituted. Among these sources, extraction of energy from the waves is considered as best option. The world oceans contain enough energy to meet the requirement of world. Significant advancements in design and technology are being made to make waves as a continuous source of energy. One major hurdle in launching wave energy devices in a developing country like Pakistan is the initial cost. A simple, reliable and cost effective wave energy converter (WEC) is required to meet the nation-s energy need. This paper will present a novel design proposed by team SAS for harnessing wave energy. This paper has three major sections. The first section will give a brief and concise view of ocean wave creation, propagation and the energy carried by them. The second section will explain the designing of SAS-2. A gear chain mechanism is used for transferring the energy from the buoy to a rotary generator. The third section will explain the manufacturing of scaled down model for SAS-2 .Many modifications are made in the trouble shooting stage. The design of SAS-2 is simple and very less maintenance is required. SAS-2 is producing electricity at Clifton. The initial cost of SAS-2 is very low. This has proved SAS- 2 as one of the cost effective and reliable source of harnessing wave energy for developing countries.
Abstract: An advanced composite flywheel rotor consisting of
intra and inter hybrid rims was designed to optimally increase the energy capacity, and was manufactured using filament winding with
in-situ curing. The flywheel has recently attracted considerable attention from many investigators since it possesses great potential in
many energy storage applications, including electric utilities, hybrid or
electric automobiles, and space vehicles. In this investigation, a comprehensive study was conducted with the intent to implement
composites in high performance flywheel applications.The inner two
intra-hybrid rims (rims 1 and 2) were manufactured as a whole part
through continuous filament winding under in-situ curing conditions,
and so were the outer two rims (rims 3 and 4). The outer surface of rim
2 and the inner surface of rim 3 were CNC-tapered for press-fitting. Machined rims were finally press-fitted using a hydraulic press with a
maximum compressive force of approximately 1000 ton.
Abstract: Fats and oils are made of esterified hydrocarbons
(RCOOR-) and this work demonstrates the substitution of R by
multi-walled CNTs (MWNTs). The resultant materials are fluidic, oily,
electrically conducting and excellent lubricants. Esterified MWNTs
can also respond to magnetic field when tubules contain long segments
of Fe
Abstract: This paper presents the impact study of GTO Controlled Series Capacitor (GCSC) parameters on measured impedance (Zseen) by MHO distance relays for single transmission line high voltage 220 kV in the presence of single phase to earth fault with fault resistance (RF). The study deals with a 220 kV single electrical transmission line of Eastern Algerian transmission networks at Group Sonelgaz (Algerian Company of Electrical and Gas) compensated by series Flexible AC Transmission System (FACTS) i.e. GCSC connected at midpoint of the transmission line. The transmitted active and reactive powers are controlled by three GCSC-s. The effects of maximum reactive power injected as well as injected maximum voltage by GCSC on distance relays measured impedance is treated. The simulations results investigate the effects of GCSC injected parameters: variable reactance (XGCSC), variable voltage (VGCSC) and reactive power injected (QGCSC) on measured resistance and reactance in the presence of earth fault with resistance fault varied between 5 to 50 Ω for three cases study.
Abstract: Today with the rapid growth of telecommunications equipment, electronic and developing more and more networks of power, influence of electromagnetic waves on one another has become hot topic discussions. So in this article, this issue and appropriate mechanisms for EMC operations have been presented. First, impact of high voltage lines on the surrounding environment especially on the control room has been investigated, then to reduce electromagnetic radiation, various methods of shielding are provided and shielding effectiveness of them has been compared. It should be expressed that simulations have been done by the finite element method (FEM).
Abstract: Nowadays, engineering ceramics have significant
applications in different industries such as; automotive, aerospace,
electrical, electronics and even martial industries due to their
attractive physical and mechanical properties like very high hardness
and strength at elevated temperatures, chemical stability, low friction
and high wear resistance. However, these interesting properties plus
low heat conductivity make their machining processes too hard,
costly and time consuming. Many attempts have been made in order
to make the grinding process of engineering ceramics easier and
many scientists have tried to find proper techniques to economize
ceramics' machining processes. This paper proposes a new diamond
plunge grinding technique using ultrasonic vibration for grinding
Alumina ceramic (Al2O3). For this purpose, a set of laboratory
equipments have been designed and simulated using Finite Element
Method (FEM) and constructed in order to be used in various
measurements. The results obtained have been compared with the
conventional plunge grinding process without ultrasonic vibration
and indicated that the surface roughness and fracture strength
improved and the grinding forces decreased.
Abstract: This paper presents a mathematical model and a
methodology to analyze the losses in transmission expansion
planning (TEP) under uncertainty in demand. The methodology is
based on discrete particle swarm optimization (DPSO). DPSO is a
useful and powerful stochastic evolutionary algorithm to solve the
large-scale, discrete and nonlinear optimization problems like TEP.
The effectiveness of the proposed idea is tested on an actual
transmission network of the Azerbaijan regional electric company,
Iran. The simulation results show that considering the losses even for
transmission expansion planning of a network with low load growth
is caused that operational costs decreases considerably and the
network satisfies the requirement of delivering electric power more
reliable to load centers.