Abstract: The present paper represents a methodology for
investigating flow characteristics near orifice plate by using a
commercial computational fluid dynamics code. The flow
characteristics near orifice plate which is located in the auxiliary
feedwater system were modeled via three different levels of grid and
four different types of Reynolds Averaged Navier-Stokes (RANS)
equations with proper near-wall treatment. The results from CFD code
were compared with experimental data in terms of differential pressure
through the orifice plate. In this preliminary study, the Realizable k-ε
and the Reynolds stress models with enhanced wall treatment were
suitable to analyze flow characteristics near orifice plate, and the
results had a good agreement with experimental data.
Abstract: Several different cements have been tested to evaluate
their potential to leach calcium, chromium and aluminum ions in soft
water environment. The research allows comparing some different
cements in order to the potential risk of water contamination. This
can be done only in the same environment. To reach the results in
reasonable short time intervals and to make heavy metals
measurements with high accuracy, demineralized water was used. In
this case the conditions of experiments are far away from the water
supply practice, but short time experiments and measurably high
concentrations of elements in the water solution are an important
advantage. Moreover leaching mechanisms can be recognized, our
experiments reported here refer to this kind of cements evaluation.
Abstract: The velocity of a moving point in a general path is the vector quantity, which has both magnitude and direction. The magnitude or the direction of the velocity vector can change over time as a result of acceleration that the time rate of velocity changes. Acceleration analysis is important because inertial forces and inertial torques are proportional to rectilinear and angular accelerations accordingly. The loads must be determined in advance to ensure that a machine is adequately designed to handle these dynamic loads. For planar motion, the vector direction of acceleration is commonly separated into two elements: tangential and centripetal or radial components of a point on a rotating body. All textbooks in physics, kinematics and dynamics of machinery consider the magnitude of a radial acceleration at condition when a point rotates with a constant angular velocity and it means without acceleration. The magnitude of the tangential acceleration considered on a basis of acceleration for a rotating point. Such condition of presentation of magnitudes for two components of acceleration logically and mathematically is not correct and may cause further confusion in calculation. This paper presents new analytical expressions of the radial and absolute accelerations of a rotating point with acceleration and covers the gap in theoretical study of acceleration analysis.
Abstract: In spite of the advent of new materials, clay bricks
remain, arguably, the most popular construction materials today.
Nevertheless the low cost and versatility of clay bricks cannot always
be associated with high environmental and sustainable values,
especially in terms of raw material sources and manufacturing
processes. At the same time, the worldwide agricultural footprint is
fast growing, with vast agricultural land cultivation and active
expansion of the agro-based industry. The resulting large quantities of
agricultural wastes, unfortunately, are not always well managed or
utilised. These wastes can be recycled, such as by retrieving fibres
from disposed leaves and fruit bunches, and then incorporated in
brick-making. This way the clay bricks are made a 'greener' building
material and the discarded natural wastes can be reutilised, avoiding
otherwise wasteful landfill and harmful open incineration. This study
examined the physical and mechanical properties of clay bricks made
by adding two natural fibres to a clay-water mixture, with baked and
non-baked conditions. The fibres were sourced from pineapple leaves
(PF) and oil palm fruit bunch (OF), and added within the range of
0.25-0.75 %. Cement was added as a binder to the mixture at 5-15 %.
Although the two fibres had different effects on the bricks produced,
cement appeared to dominate the compressive strength. The
non-baked bricks disintegrated when submerged in water, while the
baked ones displayed cement-dependent characteristics in
water-absorption and density changes. Interestingly, further increase
in fibre content did not cause significant density decrease in both the
baked and non-baked bricks.
Abstract: The combustion of liquid fuel in the porous burner
(PB) was experimented to investigate evaporation mechanism and
combustion behavior. The diesel oil was used as fuel and the pebbles
carefully chosen in the same size like the solid sphere homogeneously
was adopted as the porous media. Two structures of the liquid porous
burner, i.e. the PB without and with installation of porous emitter
(PE), were performed. PE was installed by lower than PB with
distance of 20 cm. The pebbles having porosity (φ) of 0.45 and 0.52
were, respectively, used in PB and PE. The fuel was supplied dropwise
from the top through the PB and the combustion was occurred between
PB and PE. Axial profiles of temperature along the burner length were
measured to clarify the evaporation and combustion phenomena. The
pollutant emission characteristics were monitored at the burner exit.
From the experiment, it was found that the temperature profiles of both
structures decreased with the three ways swirling air flows (QA)
increasing. On the other hand, the temperature profiles increased with
fuel heat input (QF). Obviously, the profile of the porous burner
installed with PE was higher than that of the porous burner without
PE
Abstract: In this paper, all variables are supposed to be integer
and positive. In this modern method, objective function is assumed to
be maximized or minimized but constraints are always explained like
less or equal to. In this method, choosing a dual combination of ideal
nonequivalent and omitting one of variables. With continuing this
act, finally, having one nonequivalent with (n-m+1) unknown
quantities in which final nonequivalent, m is counter for constraints,
n is counter for variables of decision.
Abstract: The use of composite materials in offshore engineering for deep sea oil production riser systems has drawn considerable interest due to the potential weight savings and improvement in durability. The design of composite risers consists of two stages: (1) local design based on critical local load cases, and (2) global analysis of the full length composite riser under global loads and assessment of critical locations. In the first stage, eight different material combinations were selected and their laminate configurations optimised under local load considerations. Stage two includes a final local stress analysis of the critical sections of the riser under the combined loads determined in the global analysis. This paper describes two design methodologies of the composite riser to provide minimum structural weight and shows that the use of off angle fibre orientations in addition to axial and hoop reinforcements offer substantial weight savings and ensure the structural capacity.
Abstract: A series of 1-(1H-benzimidazol-2-yl)-3-(substituted phenyl)-2-propen-1-one were allowed to react with hydrazine hydrate and phenyl hydrazine in submitted reactions to get pyrazoline and phenyl pyrazoline derivatives. All the compounds entered for screening at the Tuberculosis Antimicrobial Acquisition and Coordinating Facility (TAACF) for their in vitro antibacterial activity against Mycobacterium tuberculosis H37Rv strain (ATCC 27294) using Microplate Alamar Blue Assay (MABA) susceptibility test. The results expressed as MIC (minimum inhibitory concentration) in μg/mL. Among the fifteen compounds, eight compounds were found to have MIC values less than 10 μg/mL. These were subjected for cytotoxicity assay in VERO cells to determine CC50 (cytotoxic concentration 50%) values and finally SI (Selectivity Index) were calculated. Compound (XV) 2-[5-(4- fluorophenyl)-1-phenyl-4,5-dihydro-1H-3-pyrazolyl]-1Hbenzimidazole was considered the best candidate of the series that could be a good starting point to develop new lead compounds in the fight against tuberculosis.
Abstract: A universal current-mode biquad is described which
represents an economical variant of well-known KHN (Kerwin,
Huelsman, Newcomb) voltage-mode filter. The circuit consists of
two multiple-output OTAs and of two grounded capacitors. Utilizing
simple splitter of the input current and a pair of jumpers, all the basic
2nd-order transfer functions can be implemented. The principle is
verified by Spice simulation on the level of a CMOS structure of
OTAs.
Abstract: The load frequency control problem of power systems has attracted a lot of attention from engineers and researchers over the years. Increasing and quickly changing load demand, coupled with the inclusion of more generators with high variability (solar and wind power generators) on the network are making power systems more difficult to regulate. Frequency changes are unavoidable but regulatory authorities require that these changes remain within a certain bound. Engineers are required to perform the tricky task of adjusting the control system to maintain the frequency within tolerated bounds. It is well known that to minimize frequency variations, a large proportional feedback gain (speed regulation constant) is desirable. However, this improvement in performance using proportional feedback comes about at the expense of a reduced stability margin and also allows some steady-state error. A conventional PI controller is then included as a secondary control loop to drive the steadystate error to zero. In this paper, we propose a robust controller to replace the conventional PI controller which guarantees performance and stability of the power system over the range of variation of the speed regulation constant. Simulation results are shown to validate the superiority of the proposed approach on a simple single-area power system model.
Abstract: Water recycling represents an important challenge for many countries, in particular in countries where this natural resource is rare. On the other hand, in many operations, water is used as a cooling medium, as a high proportion of water consumed in industry is used for cooling purposes. Generally this water is rejected directly to the nature. This reject will cause serious environment damages as well as an important waste of this precious element.. On way to solve these problems is to reuse and recycle this warm water, through the use of natural cooling medium, such as air in a heat exchanger unit, known as a cooling tower. A poor performance, design or reliability of cooling towers will result in lower flow rate of cooling water an increase in the evaporation of water, an hence losses of water and energy. This paper which presents an experimental investigate of thermal and hydraulic performances of a mechanical cooling tower, enables to show that the water evaporation rate, Mev, increases with an increase in the air and water flow rates, as well as inlet water temperature and for fixed air flow rates, the pressure drop (ΔPw/Z) increases with increasing , L, due to the hydrodynamic behavior of the air/water flow.
Abstract: The system is made with main distributed components:
First Level: Industrial Computers placed in Control Room (monitors thermal and electrical processes based on the data provided by the second level); Second Level: PLCs which collects data from process and transmits information on the first level; also takes commands from this level which are further, passed to execution elements from third
level; Third Level: field elements consisting in 3 categories: data collecting elements; data transfer elements from the third level to the second; execution elements which take commands from the second
level PLCs and executes them after which transmits the confirmation of execution to them. The purpose of the automatic functioning is the optimization of the co-generative electrical energy commissioning in the national
energy system and the commissioning of thermal energy to the consumers.
The integrated system treats the functioning of all the equipments and devices as a whole: Gas Turbine Units (GTU); MT 20kV Medium Voltage Station (MVS); 0,4 kV Low Voltage Station (LVS); Main Hot Water Boilers (MHW); Auxiliary Hot Water Boilers (AHW); Gas Compressor Unit (GCU); Thermal Agent Circulation
Pumping Unit (TPU); Water Treating Station (WTS).
Abstract: Using of natural lighting has come into prominence in
constructed buildings, especially in last ten years, under scope of
energy efficiency. Natural lighting methods are one of the methods
that aim to take advantage of day light in maximum level and
decrease using of artificial lighting. Increasing of day light amount in
buildings by using suitable methods will give optimum result in
terms of comfort and energy saving when the daylight-artificial light
integration is ensured with a suitable control system. Using of natural
light in places that require lighting will ensure energy saving in great
extent. With this study, it is aimed to save energy used for purpose of
lighting. Under this scope, lighting of a scanning laboratory of a
hospital was realized by using a lighting automation containing
natural and artificial lighting. In natural lighting, light pipes were
used and in artificial lighting, dimmable power LED modules were
used. Necessity of lighting was followed with motion sensors. The
lighting automation containing natural and artificial light was ensured
with fuzzy logic control. At the scanning laboratory where this
application was realized, energy saving in lighting was obtained.
Abstract: The objectives of this research are to search the
management pattern of Bang Khonthi lodging entrepreneurs for
sufficient economy ways, to know the threat that affects this sector
and design fit arrangement model to sustain their business with
Samut Songkram style. What will happen if they do not use this
approach? Will they have a financial crisis? The data and information
are collected by informal discussions with 8 managers and 400
questionnaires. A mixed methods of both qualitative research and
quantitative research are used. Bent Flyvbjerg-s phronesis is utilized
for this analysis. Our research will prove that sufficient economy can
help small business firms to solve their problems. We think that the
results of our research will be a financial model to solve many
problems of the entrepreneurs and this way will can be a model for
other provinces of Thailand.
Abstract: The use of additions in cement in manufacturing,
mortar and concrete offers economic and ecological advantages. Cements with additions such as limestone, slag and natural
pouzzolana are produced in cement factories in Algeria. Several studies analyzed the effect of these additions on the physical and
mechanical properties as well as the durability of concrete. However,
few studies were conducted on the effect of local metakaolin on
mechanical properties and durability of concrete. The main purpose
of this paper is to analyze the performance of mortar and concrete with local metakaolin. The preparation of the metakaolin was carried
out by calcination of kaolin at a temperature of 850 °C for a period of 3 hours. The experimental results have shown that the rates of
substitutions of 10 and 15% metakaolin increases the compressive
strength and flexural strength at both early age and long term. The durability and the permeability were also improved by reducing the
coefficient of sorptivity.
Abstract: CIM is the standard formalism for modeling management
information developed by the Distributed Management Task
Force (DMTF) in the context of its WBEM proposal, designed to
provide a conceptual view of the managed environment. In this
paper, we propose the inclusion of formal knowledge representation
techniques, based on Description Logics (DLs) and the Web Ontology
Language (OWL), in CIM-based conceptual modeling, and then we
examine the benefits of such a decision. The proposal is specified
as a CIM metamodel level mapping to a highly expressive subset
of DLs capable of capturing all the semantics of the models. The
paper shows how the proposed mapping provides CIM diagrams with
precise semantics and can be used for automatic reasoning about the
management information models, as a design aid, by means of newgeneration
CASE tools, thanks to the use of state-of-the-art automatic
reasoning systems that support the proposed logic and use algorithms
that are sound and complete with respect to the semantics. Such a
CASE tool framework has been developed by the authors and its
architecture is also introduced. The proposed formalization is not
only useful at design time, but also at run time through the use of
rational autonomous agents, in response to a need recently recognized
by the DMTF.
Abstract: Buildings are considered as significant part in the
cities, which plays main role in organization and arrangement of city
appearance, which is affects image of that building facades, as an
connective between inner and outer space, have a main role in city
image and they are classified as rich image and poor image by people
evaluation which related to visual architectural and urban elements in
building facades. the buildings in Karimi street , in Lahijan city
where, lies in north of Iran, contain the variety of building's facade
types which, have made a city image in Historical part of Lahijan
city, while reflected the Iranian cities identity. The study attempt to
identify the architectural and urban elements that impression the
image of building facades in historical area, based on public
evaluation. Quantitative method were used and the data was collected
through questionnaire survey, the result presented architectural style,
color, shape, and design evaluated by people as most important factor
which should be understate in future development. in fact, the rich
architectural style with strong design make strong city image as weak
design make poor city image.
Abstract: This article presents a simple way to perform programmed voice commands for the interface with commercial Digital and Analogue Input/Output PCI cards, used in Robotics and Automation applications. Robots and Automation equipment can "listen" to voice commands and perform several different tasks, approaching to the human behavior, and improving the human- machine interfaces for the Automation Industry. Since most PCI Digital and Analogue Input/Output cards are sold with several DLLs included (for use with different programming languages), it is possible to add speech recognition capability, using a standard speech recognition engine, compatible with the programming languages used. It was created in this work a Visual Basic 6 (the world's most popular language) application, that listens to several voice commands, and is capable to communicate directly with several standard 128 Digital I/O PCI Cards, used to control complete Automation Systems, with up to (number of boards used) x 128 Sensors and/or Actuators.
Abstract: This work presents the mixed-mode II/III prestressed split-cantilever beam specimen for the fracture testing of composite materials. In accordance with the concept of prestressed composite beams one of the two fracture modes is provided by the prestressed state of the specimen, and the other one is increased up to fracture initiation by using a testing machine. The novel beam-like specimen is able to provide any combination of the mode-II and mode-III energy release rates. A simple closed-form solution is developed using beam theory as a data reduction scheme and for the calculation of the energy release rates in the new configuration. The applicability and the limitations of the novel fracture mechanical test are demonstrated using unidirectional glass/polyester composite specimens. If only crack propagation onset is involved then the mixed-mode beam specimen can be used to obtain the fracture criterion of transparent composite materials in the GII - GIII plane in a relatively simple way.
Abstract: The study applied a combination of organisational learning models (Senge, 1994: Pedler, Burgoyne and Boydell, 1991) and later adopted fifteen organisational learning principles with one of the biggest energy providers in South East Asia. The purposes of the current study were to: a) investigate the company-s practices on fifteen organisational learning principles; b) explore the perceptions and expectations of its employees in relations to the principles; and c) compare the perceptions and expectations between management and non-management staff toward the fifteen factors. One hundred and ten employees responded on a designed questionnaire and the results indicated that the company was practicing activities that associated with organisational learning principles. Also, according to the T-test results, significant differences between management and non-management respondents were found. Research implications are also provided.