Abstract: This article gives a short preview of the new software
created especially for palletizing process in automated production
systems. Each chapter of this article is about problem solving in
development of modules in Java programming language. First part
describes structure of the software, its modules and data flow
between them. Second part describes all deployment methods, which
are implemented in the software. Next chapter is about twodimensional
editor created for manipulation with objects in each
layer of the load and gives calculations for collision control. Module
of virtual reality used for three-dimensional preview and creation of
the load is described in the fifth chapter. The last part of this article
describes communication and data flow between control system of
the robot, vision system and software.
Abstract: The tubes in an Ammonia primary reformer furnace
operate close to the limits of materials technology in terms of the
stress induced as a result of very high temperatures, combined with
large differential pressures across the tube wall. Operation at tube
wall temperatures significantly above design can result in a rapid
increase in the number of tube failures, since tube life is very
sensitive to the absolute operating temperature of the tube. Clearly it
is important to measure tube wall temperatures accurately in order to
prevent premature tube failure by overheating.. In the present study,
the catalyst tubes in an Ammonia primary reformer has been modeled
taking into consideration heat, mass and momentum transfer as well
as reformer characteristics.. The investigations concern the effects of
tube characteristics and superficial tube wall temperatures on of the
percentage of heat flux, unconverted methane and production of
Hydrogen for various values of steam to carbon ratios. The results
show the impact of catalyst tubes length and diameters on the
performance of operating parameters in ammonia primary reformers.
Abstract: A two-parameter fatigue model explicitly accounting for the cyclic as well as the mean stress was used to fit static and fatigue data available in literature concerning carbon fiber reinforced composite laminates subjected tension-tension fatigue. The model confirms the strength–life equal rank assumption and predicts reasonably the probability of failure under cyclic loading. The model parameters were found by best fitting procedures and required a minimum of experimental tests.
Abstract: The springs located in urban areas are the outpouring
of surface water, which can serve as water supply, effluent receptors
and important local macro-drainage elements. With unplanned
occupation, non-compliance with environmental legislation and the
importance of these water bodies, it is vital to analyze the springs
within urban areas, considering the Brazilian forest code. This paper
submits an analysis and discussion methodology proposal of
environmental compliance functions of urban springs, by means of
G.I.S. - Geographic Information System analysis - and in situ
analysis. The case study included two springs which exhibit a history
of occupation along its length, with different degrees of impact. The
proposed method is effective and easy to apply, representing a
powerful tool for analyzing the environmental conditions of springs
in urban areas.
Abstract: In this paper back-propagation artificial neural
network (BPANN) is employed to predict the limiting drawing ratio
(LDR) of the deep drawing process. To prepare a training set for
BPANN, some finite element simulations were carried out. die and
punch radius, die arc radius, friction coefficient, thickness, yield
strength of sheet and strain hardening exponent were used as the
input data and the LDR as the specified output used in the training of
neural network. As a result of the specified parameters, the program
will be able to estimate the LDR for any new given condition.
Comparing FEM and BPANN results, an acceptable correlation was
found.
Abstract: In this paper, a simple microfluidic device for monitoring algal cell behavior is proposed. An array of algal microwells is fabricated by PDMS soft-lithography using X-ray LIGA mold, placed on a glass substrate. Two layers of replicated PDMS and substrate are attached by oxygen plasma bonding, creating a microchannel for the microfluidic system. Algal cell are loaded into the microfluidic device, which provides positive charge on the bottom surface of wells. Algal cells, which are negative charged, can be attracted to the bottom of the wells via electrostatic interaction. By varying the concentration of algal cells in the loading suspension, it is possible to obtain wells with a single cell. Liquid medium for cells monitoring are flown continuously over the wells, providing nutrient and waste exchange between the well and the main flow. This device could lead to the uncovering of the quantitative biology of the algae, which is a key to effective and extensive algal utilizations in the field of biotechnology, food industry and bioenergy research and developments.
Abstract: Cross layer optimization based on utility functions has
been recently studied extensively, meanwhile, numerous types of
utility functions have been examined in the corresponding literature.
However, a major drawback is that most utility functions take a fixed
mathematical form or are based on simple combining, which can
not fully exploit available information. In this paper, we formulate a
framework of cross layer optimization based on Adaptively Weighted
Utility Functions (AWUF) for fairness balancing in OFDMA networks.
Under this framework, a two-step allocation algorithm is
provided as a sub-optimal solution, whose control parameters can be
updated in real-time to accommodate instantaneous QoS constrains.
The simulation results show that the proposed algorithm achieves
high throughput while balancing the fairness among multiple users.
Abstract: This paper discusses the approach of real-time
controlling of the energy management system using the data
acquisition tool of LabVIEW. The main idea of this inspiration was
to interface the Station (PC) with the system and publish the data on
internet using LabVIEW. In this venture, controlling and switching of
3 phase AC loads are effectively and efficiently done. The phases are
also sensed through devices. In case of any failure the attached
generator starts functioning automatically. The computer sends
command to the system and system respond to the request. The
modern feature is to access and control the system world-wide using
world wide web (internet). This controlling can be done at any time
from anywhere to effectively use the energy especially in developing
countries where energy management is a big problem. In this system
totally integrated devices are used to operate via remote location.
Abstract: loss of feedwater accident is one of the frequently sever accidents in steam boiler facilities. It threatens the system structural integrity and generates serious hazards and economic loses. The safety analysis of the thermal installations, based extensively on the numeric simulation. The simulation analysis using realistic computer codes like Relap5/Mod3.2 will help understand steam boiler thermal-hydraulic behavior during normal and abnormal conditions. In this study, we are interested on the evaluation of the radiant steam boiler assessment and response to loss-of-feedwater accident. Pressure, temperature and flow rate profiles are presented in various steam boiler system components. The obtained results demonstrate the importance and capability of the Relap5/Mod3.2 code in the thermal-hydraulic analysis of the steam boiler facilities.
Abstract: Blind Signature were introduced by Chaum. In this
scheme, a signer can “sign” a document without knowing the
document contain. This is particularly important in electronic voting.
CryptO-0N2 is an electronic voting protocol which is development of
CryptO-0N. During its development this protocol has not been
furnished with the requirement of blind signature, so the choice of
voters can be determined by counting center. In this paper will be
presented of implementation of blind signature using RSA algorithm.
Abstract: Gas flaring is one of the most GHG emitting sources in the oil and gas industries. It is also a major way for wasting such an energy that could be better utilized and even generates revenue. Minimize flaring is an effective approach for reducing GHG emissions and also conserving energy in flaring systems. Integrating waste and flared gases into the fuel gas networks (FGN) of refineries is an efficient tool. A fuel gas network collects fuel gases from various source streams and mixes them in an optimal manner, and supplies them to different fuel sinks such as furnaces, boilers, turbines, etc. In this article we use fuel gas network model proposed by Hasan et al. as a base model and modify some of its features and add constraints on emission pollution by gas flaring to reduce GHG emissions as possible. Results for a refinery case study showed that integration of flare gas stream with waste and natural gas streams to construct an optimal FGN can significantly reduce total annualized cost and flaring emissions.
Abstract: Embedding Sustainability in technological curricula has become a crucial factor for educating engineers with competences in sustainability. The Technical University of Catalonia UPC, in 2008, designed the Sustainable Technology Excellence Program STEP 2015 in order to assure a successful Sustainability Embedding. This Program takes advantage of the opportunity that the redesign of all Bachelor and Master Degrees in Spain by 2010 under the European Higher Education Area framework offered. The STEP program goals are: to design compulsory courses in each degree; to develop the conceptual base and identify reference models in sustainability for all specialties at UPC; to create an internal interdisciplinary network of faculty from all the schools; to initiate new transdisciplinary research activities in technology-sustainability-education; to spread the know/how attained; to achieve international scientific excellence in technology-sustainability-education and to graduate the first engineers/architects of the new EHEA bachelors with sustainability as a generic competence. Specifically, in this paper authors explain their experience in leading the STEP program, and two examples are presented: Industrial Robotics subject and the curriculum for the School of Architecture.
Abstract: In this research, a systematic investigation was carried out to determine the optimum conditions of HDS reactor. Moreover, a suitable model was developed for a rigorous RTO (real time optimization) loop of HDS (Hydro desulfurization) process. A systematic experimental series was designed based on CCD (Central Composite design) and carried out in the related pilot plant to tune the develop model. The designed variables in the experiments were Temperature, LHSV and pressure. However, the hydrogen over fresh feed ratio was remained constant. The ranges of these variables were respectively equal to 320-380ºC, 1- 21/hr and 50-55 bar. a power law kinetic model was also developed for our further research in the future .The rate order and activation energy , power of reactant concentration and frequency factor of this model was respectively equal to 1.4, 92.66 kJ/mol and k0=2.7*109 .
Abstract: Benchmarking cleaner production performance is an
effective way of pollution control and emission reduction in coal-fired
power industry. A benchmarking method using two-stage
super-efficiency data envelopment analysis for coal-fired power plants
is proposed – firstly, to improve the cleaner production performance of
DEA-inefficient or weakly DEA-efficient plants, then to select the
benchmark from performance-improved power plants. An empirical
study is carried out with the survey data of 24 coal-fired power plants.
The result shows that in the first stage the performance of 16 plants is
DEA-efficient and that of 8 plants is relatively inefficient. The target
values for improving DEA-inefficient plants are acquired by
projection analysis. The efficient performance of 24 power plants and
the benchmarking plant is achieved in the second stage. The two-stage
benchmarking method is practical to select the optimal benchmark in
the cleaner production of coal-fired power industry and will
continuously improve plants- cleaner production performance.
Abstract: The Reverse Monte Carlo (RMC) simulation is applied in the study of an aqueous electrolyte LiCl6H2O. On the basis of the available experimental neutron scattering data, RMC computes pair radial distribution functions in order to explore the structural features of the system. The obtained results include some unrealistic features. To overcome this problem, we use the Hybrid Reverse Monte Carlo (HRMC), incorporating an energy constraint in addition to the commonly used constraints derived from experimental data. Our results show a good agreement between experimental and computed partial distribution functions (PDFs) as well as a significant improvement in pair partial distribution curves. This kind of study can be considered as a useful test for a defined interaction model for conventional simulation techniques.
Abstract: The objective of this work was to investigate flow
properties of powdered infant formula samples. Samples were
purchased at a local pharmacy and differed in composition. Lactose
free infant formula, gluten free infant formula and infant formulas
containing dietary fibers and probiotics were tested and compared
with a regular infant formula sample which did not contain any of
these supplements. Particle size and bulk density were determined
and their influence on flow properties was discussed. There were no
significant differences in bulk densities of the samples, therefore the
connection between flow properties and bulk density could not be
determined. Lactose free infant formula showed flow properties
different to standard supplement-free sample. Gluten free infant
formula with addition of probiotic microorganisms and dietary fiber
had the narrowest particle size distribution range and exhibited the
best flow properties. All the other samples exhibited the same
tendency of decreasing compaction coefficient with increasing flow
speed, which means they all become freer flowing with higher flow
speeds.
Abstract: Many real-world data sets consist of a very high dimensional feature space. Most clustering techniques use the distance or similarity between objects as a measure to build clusters. But in high dimensional spaces, distances between points become relatively uniform. In such cases, density based approaches may give better results. Subspace Clustering algorithms automatically identify lower dimensional subspaces of the higher dimensional feature space in which clusters exist. In this paper, we propose a new clustering algorithm, ISC – Intelligent Subspace Clustering, which tries to overcome three major limitations of the existing state-of-art techniques. ISC determines the input parameter such as є – distance at various levels of Subspace Clustering which helps in finding meaningful clusters. The uniform parameters approach is not suitable for different kind of databases. ISC implements dynamic and adaptive determination of Meaningful clustering parameters based on hierarchical filtering approach. Third and most important feature of ISC is the ability of incremental learning and dynamic inclusion and exclusions of subspaces which lead to better cluster formation.
Abstract: We present a prototype interactive (hyper) map of strategic, tactical, and logistic options for Supply Chain Management. The map comprises an anthology of options, broadly classified within the strategic spectrum of efficiency versus responsiveness, and according to logistic and cross-functional drivers. They are exemplified by cases in diverse industries. We seek to get all these information and ideas organized to help supply chain managers identify effective choices for specific business environments. The key and innovative linkage we introduce is the configuration of competitive forces. Instead of going through seemingly endless and isolated cases and wondering how one can borrow from them, we aim to provide a guide by force comparisons. The premise is that best practices in a different industry facing similar forces may be a most productive resource in supply chain design and planning. A prototype template is demonstrated.
Abstract: Paced Auditory Serial Addition Test (PASAT) has
been used as a common research tool for different neurological
disorders like Multiple Sclerosis. Recently, technology let
researchers to introduce a new versions of the visual test, the paced
visual serial addition test (PVSAT). In this paper, the computerized
version of these two tests is introduced. Beside the number of true
responses are interpreted, the reaction time of subjects are calculated
by the software. We hypothesize that paying attention to the reaction
time may be valuable. For this purpose, sixty eight female normal
subjects and fifty eight male normal subjects are enrolled in the
study. We investigate the similarity between the PASAT3 and
PVSAT3 in number of true responses and the new criterion (the
average reaction time of each subject). The similarity between two
tests were rejected (p-value = 0.000) which means that these two test
differ. The effect of sex in the tests were not approved since the pvalues
of different between PASAT3 and PVSAT3 in both sex is the
same (p-value = 0.000) which means that male and female subjects
performed the tests at no different level of performance. The new
criterion shows a negative correlation with the age which offers aged
normal subjects may have the same number of true responses as the
young subjects but they have latent responses. This will give prove
for the importance of reaction time.
Abstract: The noteworthy point in the advancement of Brain Machine Interface (BMI) research is the ability to accurately extract features of the brain signals and to classify them into targeted control action with the easiest procedures since the expected beneficiaries are of disabled. In this paper, a new feature extraction method using the combination of adaptive band pass filters and adaptive autoregressive (AAR) modelling is proposed and applied to the classification of right and left motor imagery signals extracted from the brain. The introduction of the adaptive bandpass filter improves the characterization process of the autocorrelation functions of the AAR models, as it enhances and strengthens the EEG signal, which is noisy and stochastic in nature. The experimental results on the Graz BCI data set have shown that by implementing the proposed feature extraction method, a LDA and SVM classifier outperforms other AAR approaches of the BCI 2003 competition in terms of the mutual information, the competition criterion, or misclassification rate.