Abstract: A piston cylinder based high pressure differential
thermal analyzer system is developed to investigate phase
transformations, melting, glass transitions, crystallization behavior of
inorganic materials, glassy systems etc., at ambient to 4 GPa and at
room temperature to 1073 K. The pressure is calibrated by the phase
transition of bismuth and ytterbium and temperature is calibrated
by using thermocouple data chart. The system developed is
calibrated using benzoic acid, ammonium nitrate and it has a
pressure and temperature control of ± 8.9 x 10 -4 GPa , ± 2 K
respectively. The phase transition of Asx Te100-x chalcogenides,
ferrous oxide and strontium boride are studied using the
indigenously developed system.
Abstract: Cerium-doped lanthanum bromide LaBr3:Ce(5%)
crystals are considered to be one of the most advanced scintillator
materials used in PET scanning, combining a high light yield, fast
decay time and excellent energy resolution. Apart from the correct
choice of scintillator, it is also important to optimise the detector
geometry, not least in terms of source-to-detector distance in order to
obtain reliable measurements and efficiency. In this study a
commercially available 25 mm x 25 mm BrilLanCeTM 380 LaBr3: Ce
(5%) detector was characterised in terms of its efficiency at varying
source-to-detector distances. Gamma-ray spectra of 22Na, 60Co, and
137Cs were separately acquired at distances of 5, 10, 15, and 20cm. As
a result of the change in solid angle subtended by the detector, the
geometric efficiency reduced in efficiency with increasing distance.
High efficiencies at low distances can cause pulse pile-up when
subsequent photons are detected before previously detected events
have decayed. To reduce this systematic error the source-to-detector
distance should be balanced between efficiency and pulse pile-up
suppression as otherwise pile-up corrections would need to be
necessary at short distances. In addition to the experimental
measurements Monte Carlo simulations have been carried out for the
same setup, allowing a comparison of results. The advantages and
disadvantages of each approach have been highlighted.
Abstract: It is well known that the phraseology of a language - the phenomenon of identity. This uniqueness is due to the fact that "there are idioms image-based views of reality that shows mainly of everyday empirical, historical and spiritual experience of a language community, associated with its cultural traditions. The article says that the phraseological units very clearly show the image of the people and give us a great view of the national identity. With the phraseology of the Kazakh and Korean language can understand the mentality of the nation, identity, perception of people. It is in the phraseological units can surprise the culture and customs of the people. Phraseological units store and transmit information about the level of material and spiritual culture of the people, his life, past and present, the development of society in general. And in Korean and Kazakh languages idioms occupy a particularly important role.
Abstract: Quality of 2D and 3D cross-sectional images produce
by Computed Tomography primarily depend upon the degree of
precision of primary and secondary X-Ray intensity detection.
Traditional method of primary intensity detection is apt to errors.
Recently the X-Ray intensity measurement system along with smart
X-Ray sensors is developed by our group which is able to detect
primary X-Ray intensity unerringly. In this study a new smart X-Ray
sensor is developed using Light-to-Frequency converter TSL230
from Texas Instruments which has numerous advantages in terms of
noiseless data acquisition and transmission. TSL230 construction is
based on a silicon photodiode which converts incoming X-Ray
radiation into the proportional current signal. A current to frequency
converter is attached to this photodiode on a single monolithic CMOS
integrated circuit which provides proportional frequency count to
incoming current signal in the form of the pulse train. The frequency
count is delivered to the center of PICDEM FS USB board with
PIC18F4550 microcontroller mounted on it. With highly compact
electronic hardware, this Demo Board efficiently read the smart
sensor output data. The frequency output approaches overcome
nonlinear behavior of sensors with analog output thus un-attenuated
X-Ray intensities could be measured precisely and better
normalization could be acquired in order to attain high resolution.
Abstract: The state-of-the-art Bag of Words model in Content-
Based Image Retrieval has been used for years but the relevance
feedback strategies for this model are not fully investigated. Inspired
from text retrieval, the Bag of Words model has the ability to use the
wealth of knowledge and practices available in text retrieval. We
study and experiment the relevance feedback model in text retrieval
for adapting it to image retrieval. The experiments show that the
techniques from text retrieval give good results for image retrieval
and that further improvements is possible.
Abstract: The primary cause of Total Hip Replacement (THR)
failure for younger patients is aseptic loosening. This complication is
twice more likely to happen in acetabular cup than in femoral stem.
Excessive micromotion between bone and implant will cause
loosening and it depends in patient activities, age and bone. In this
project, the effects of different metal back design of press fit on
osseointegration of the acetabular cup are carried out. Commercial
acetabular cup designs, namely Spiked, Superfix and Quadrafix are
modelled and analyzed using commercial finite element software.
The diameter of acetabular cup is based on the diameter of acetabular
rim to make sure the component fit to the acetabular cavity. A new
design of acetabular cup are proposed and analyzed to get better
osseointegration between the bones and implant interface. Results
shows that the proposed acetabular cup designs are more stable
compared to other designs with respect to stress and displacement
aspects.
Abstract: The present research was designed to investigate the
anti-microbial activity of aristolochic acid from the root of
Aristolochia bracteata. From the methanolic & ethyl extract extracts
of Aristolochia bracteata aristolochic acid I was isolated and
conformed through IR, NMR & MS. The percentage purity of
aristolochic acid I was determined by UV & HPLC method. Antibacterial
activity of extracts of Aristolochia bracteata and the
isolated compound was determined by disc diffusion method. The
results reveled that the isolated aristolochic acid from methanolic
extract was more pure than the compound from ethyl acetate extract.
The various extracts (500μg/disc) of Aristolochia bracteata showed
moderate antibacterial activity with the average zone of inhibition of
7-18 mm by disc diffusion method. Among the extracts, ethyl acetate
& methanol extracts were shown good anti-microbial activity and the
growth of E.coli (18 mm) was strongly inhibited. Microbial assay of
isolated compound (Aristolochic acid I) from ethyl acetate &
methanol extracts were shown good antimicrobial activity and the
zone of inhibition of both at higher concentration 50 μg/ml was
similar with the standard aristolochic acid. It may be concluded that
the isolated compound of aristolochic acid I has good anti-bacterial
activity.
Abstract: The purpose of this study was to explore the complex
flow structure a novel active-type micromixer that based on concept of
Wankle-type rotor. The characteristics of this micromixer are two
folds; a rapid mixing of reagents in a limited space due to the
generation of multiple vortices and a graduate increment in dynamic
pressure as the mixed reagents is delivered to the output ports.
Present micro-mixer is consisted of a rotor with shape of triangle
column, a blending chamber and several inlet and outlet ports. The
geometry of blending chamber is designed to make the rotor can be
freely internal rotated with a constant eccentricity ratio. When the
shape of the blending chamber and the rotor are fixed, the effects of
rotating speed of rotor and the relative locations of ports on the mixing
efficiency are numerical studied. The governing equations are
unsteady, two-dimensional incompressible Navier-Stokes equation
and the working fluid is the water. The species concentration equation
is also solved to reveal the mass transfer process of reagents in various
regions then to evaluate the mixing efficiency.
The dynamic mesh technique was implemented to model the
dynamic volume shrinkage and expansion of three individual
sub-regions of blending chamber when the rotor conducted a complete
rotating cycle. Six types of ports configuration on the mixing
efficiency are considered in a range of Reynolds number from 10 to
300. The rapid mixing process was accomplished with the multiple
vortex structures within a tiny space due to the equilibrium of shear
force, viscous force and inertial force. Results showed that the highest
mixing efficiency could be attained in the following conditions: two
inlet and two outlet ports configuration, that is an included angle of 60
degrees between two inlets and an included angle of 120 degrees
between inlet and outlet ports when Re=10.
Abstract: Images of human iris contain specular highlights due
to the reflective properties of the cornea. This corneal reflection
causes many errors not only in iris and pupil center estimation but
also to locate iris and pupil boundaries especially for methods that
use active contour. Each iris recognition system has four steps:
Segmentation, Normalization, Encoding and Matching. In order to
address the corneal reflection, a novel reflection removal method is
proposed in this paper. Comparative experiments of two existing
methods for reflection removal method are evaluated on CASIA iris
image databases V3. The experimental results reveal that the
proposed algorithm provides higher performance in reflection
removal.
Abstract: An efficient architecture for low jitter All Digital
Phase Locked Loop (ADPLL) suitable for high speed SoC
applications is presented in this paper. The ADPLL is designed using
standard cells and described by Hardware Description Language
(HDL). The ADPLL implemented in a 90 nm CMOS process can
operate from 10 to 200 MHz and achieve worst case frequency
acquisition in 14 reference clock cycles. The simulation result shows
that PLL has cycle to cycle jitter of 164 ps and period jitter of 100 ps
at 100MHz. Since the digitally controlled oscillator (DCO) can
achieve both high resolution and wide frequency range, it can meet
the demands of system-level integration. The proposed ADPLL can
easily be ported to different processes in a short time. Thus, it can
reduce the design time and design complexity of the ADPLL, making
it very suitable for System-on-Chip (SoC) applications.
Abstract: The aim of current study was to investigate the
changes in the quality parameters of Holstein bull semen during the
heat stress and the effect of feeding a source of omega-3 fatty acids
in this period. Samples were obtained from 19 Holstein bulls during
the expected time of heat stress in Iran (June to September 2009).
Control group (n=10) were fed a standard concentrate feed while
treatment group (n=9) had this feed top dressed with 100 g of an
omega-3 enriched nutriceutical. Semen quality was assessed on
ejaculates collected after 1, 5, 9 and 12 weeks of supplementation.
Computer-assisted assessment of sperm motility, viability (eosinnigrosin)
and hypo-osmotic swelling test (HOST) were conducted.
Heat stress affected sperm quality parameters by week 5 and 9
(p
Abstract: Image Searching was always a problem specially when these images are not properly managed or these are distributed over different locations. Currently different techniques are used for image search. On one end, more features of the image are captured and stored to get better results. Storing and management of such features is itself a time consuming job. While on the other extreme if fewer features are stored the accuracy rate is not satisfactory. Same image stored with different visual properties can further reduce the rate of accuracy. In this paper we present a new concept of using polynomials of sorted histogram of the image. This approach need less overhead and can cope with the difference in visual features of image.
Abstract: A manufacturing inventory model with shortages with
carrying cost, shortage cost, setup cost and demand quantity as
imprecise numbers, instead of real numbers, namely interval number
is considered here. First, a brief survey of the existing works on
comparing and ranking any two interval numbers on the real line
is presented. A common algorithm for the optimum production
quantity (Economic lot-size) per cycle of a single product (so as
to minimize the total average cost) is developed which works well
on interval number optimization under consideration. Finally, the
designed algorithm is illustrated with numerical example.
Abstract: The past decade has witnessed a good opportunities
for city development schemes in UK. The government encouraged
restoration of city centers to comprise mixed use developments with
high density residential apartments. Investments in regeneration areas
were doing well according to the analyses of Property Databank
(IPD). However, more recent analysis by IPD has shown that since
2007, property in regeneration areas has been more vulnerable to the
market downturn than other types of investment property. The early
stages of a property market downturn may be felt most in
regeneration where funding, investor confidence and occupier
demand would dissipate because the sector was considered more
marginal or risky when development costs rise. Moreover, the Bank
of England survey shows that lenders have sequentially tightened the
availability of credit for commercial real estate since mid-2007. A
sharp reduction in the willingness of banks to lend on commercial
property was recorded. The credit crunch has already affected
commercial property but its impact has been particularly severe in
certain kinds of properties where residential developments are
extremely difficult, in particular city centre apartments and buy-to-let
markets. Commercial property – retail, industrial leisure and mixed
use were also pressed, in Birmingham; tens of mixed use plots were
built to replace old factories in the heart of the city. The purpose of
these developments was to enable young professionals to work and
live in same place. Thousands of people lost their jobs during the
recession, moreover lending was more difficult and the future of
many developments is unknown. The recession casts its shadow upon
the society due to cuts in public spending by government, Inflation,
rising tuition fees and high rise in unemployment generated anger and
hatred was spreading among youth causing vandalism and riots in
many cities. Recent riots targeted many mixed used development in
the UK where banks, shops, restaurants and big stores were robbed
and set into fire leaving residents with horror and shock. This paper
examines the impact of the recession and riots on mixed use
development in UK.
Abstract: In this paper, we propose a Perceptually Optimized Embedded ZeroTree Image Coder (POEZIC) that introduces a perceptual weighting to wavelet transform coefficients prior to control SPIHT encoding algorithm in order to reach a targeted bit rate with a perceptual quality improvement with respect to the coding quality obtained using the SPIHT algorithm only. The paper also, introduces a new objective quality metric based on a Psychovisual model that integrates the properties of the HVS that plays an important role in our POEZIC quality assessment. Our POEZIC coder is based on a vision model that incorporates various masking effects of human visual system HVS perception. Thus, our coder weights the wavelet coefficients based on that model and attempts to increase the perceptual quality for a given bit rate and observation distance. The perceptual weights for all wavelet subbands are computed based on 1) luminance masking and Contrast masking, 2) the contrast sensitivity function CSF to achieve the perceptual decomposition weighting, 3) the Wavelet Error Sensitivity WES used to reduce the perceptual quantization errors. The new perceptually optimized codec has the same complexity as the original SPIHT techniques. However, the experiments results show that our coder demonstrates very good performance in terms of quality measurement.
Abstract: Fatigue cracking continues to be the main challenges in
improving the performance of bituminous mixture pavements. The
purpose of this paper is to look at some aspects of the effects of fine
aggregate properties on the fatigue behaviour of hot mixture asphalt.
Two types of sand (quarry and mining sand) with two conventional
bitumen (PEN 50/60 & PEN 80/100) and four polymers modified
bitumen PMB (PM1_82, PM1_76, PM2_82 and PM2_76) were used.
Physical, chemical and mechanical tests were performed on the sands
to determine their effect when incorporated with a bituminous
mixture. According to the beam fatigue results, quarry sand that has
more angularity, rougher, higher shear strength and a higher
percentage of Aluminium oxide presented higher resistance to
fatigue. Also a PMB mixture gives better fatigue results than
conventional mixtures, this is due to the PMB having better viscosity
property than that of the conventional bitumen.
Abstract: This paper argues that networks, such as the ECN and the American network, are affected by certain small events which are inherent to path dependence and preclude the full evolution towards efficiency. It is advocated that the American network is superior to the ECN in many respects due to its greater flexibility and longer history. This stems in particular from the creation of the American network, which was based on a small number of cases. Such a structure encourages further changes and modifications which are not necessarily radical. The ECN, by contrast, was established by legislative action, which explains its rigid structure and resistance to change. This paper is an attempt to transpose the superiority of the American network on to the ECN. It looks at concepts such as judicial cooperation, harmonisation of procedure, peer review and regulatory impact assessments (RIAs), and dispute resolution procedures.
Abstract: In this paper, we investigate the strategic stochastic air traffic flow management problem which seeks to balance airspace capacity and demand under weather disruptions. The goal is to reduce the need for myopic tactical decisions that do not account for probabilistic knowledge about the NAS near-future states. We present and discuss a scenario-based modeling approach based on a time-space stochastic process to depict weather disruption occurrences in the NAS. A solution framework is also proposed along with a distributed implementation aimed at overcoming scalability problems. Issues related to this implementation are also discussed.
Abstract: Studies on Simultaneous Saccharification and Fermentation (SSF) of corn flour, a major agricultural product as the substrate using starch digesting glucoamylase enzyme derived from Aspergillus niger and non starch digesting and sugar fermenting Saccharomyces cerevisiae in a batch fermentation. Experiments based on Central Composite Design (CCD) were conducted to study the effect of substrate concentration, pH, temperature, enzyme concentration on Ethanol Concentration and the above parameters were optimized using Response Surface Methodology (RSM). The optimum values of substrate concentration, pH, temperature and enzyme concentration were found to be 160 g/l, 5.5, 30°C and 50 IU respectively. The effect of inoculums age on ethanol concentration was also investigated. The corn flour solution equivalent to 16% initial starch concentration gave the highest ethanol concentration of 63.04 g/l after 48 h of fermentation at optimum conditions of pH and temperature. Monod model and Logistic model were used for growth kinetics and Leudeking – Piret model was used for product formation kinetics.
Abstract: Tool Tracker is a client-server based application. It is essentially a catalogue of various network monitoring and management tools that are available online. There is a database maintained on the server side that contains the information about various tools. Several clients can access this information simultaneously and utilize this information. The various categories of tools considered are packet sniffers, port mappers, port scanners, encryption tools, and vulnerability scanners etc for the development of this application. This application provides a front end through which the user can invoke any tool from a central repository for the purpose of packet sniffing, port scanning, network analysis etc. Apart from the tool, its description and the help files associated with it would also be stored in the central repository. This facility will enable the user to view the documentation pertaining to the tool without having to download and install the tool. The application would update the central repository with the latest versions of the tools. The application would inform the user about the availability of a newer version of the tool currently being used and give the choice of installing the newer version to the user. Thus ToolTracker provides any network administrator that much needed abstraction and ease-ofuse with respect to the tools that he can use to efficiently monitor a network.