Abstract: Two different superhydrophobic surfaces were
elaborated and their oil repellency behavior was evaluated using
several liquid with different surface tension. A silicone rubber/SiO2
nanocomposite coated (A) on aluminum substrate by “spin-coating"
and the sample B was an anodized aluminum surface covered by
Teflon-like coating. A high static contact angle about ∼162° was
measured for two prepared surfaces on which the water droplet rolloff.
Scanning electron microscopy (SEM) showed the presence of
micro/nanostructures for both sample A and B similar to that of lotus
leaf.
However the sample A presented significantly different behaviour
of wettability against the low surface tension liquid. Sample A has
been wetted totally by oil (dodecan) droplet while sample B showed
oleophobic behaviour. Oleophobic property of Teflon like coating
can be contributed to the presence of CF2 and CF3 functional group
which was shown by XPS analysis.
Abstract: The three-dimensional incompressible flow past a
rectangular open cavity is investigated, where the aspect ratio of the
cavity is considered as 4. The principle objective is to use large-eddy
simulation to resolve and control the large-scale structures, which are
largely responsible for flow oscillations in a cavity. The flow past an
open cavity is very common in aerospace applications and can be a
cause of acoustic source due to hydrodynamic instability of the shear
layer and its interactions with the downstream edge. The unsteady
Navier-stokes equations have been solved on a staggered mesh using
a symmetry-preserving central difference scheme. Synthetic jet has
been used as an active control to suppress the cavity oscillations in
wake mode for a Reynolds number of ReD = 3360. The effect of
synthetic jet has been studied by varying the jet amplitude and
frequency, which is placed at the upstream wall of the cavity. The
study indicates that there exits a frequency band, which is larger than
a critical value, is effective in attenuating cavity oscillations when
blowing ratio is more than 1.0.
Abstract: Organization of video databases is becoming difficult
task as the amount of video content increases. Video classification
based on the content of videos can significantly increase the speed of
tasks such as browsing and searching for a particular video in a
database. In this paper, a content-based videos classification system
for the classes indoor and outdoor is presented. The system is
intended to be used on a mobile platform with modest resources. The
algorithm makes use of the temporal redundancy in videos, which
allows using an uncomplicated classification model while still
achieving reasonable accuracy. The training and evaluation was done
on a video database of 443 videos downloaded from a video sharing
service. A total accuracy of 87.36% was achieved.
Abstract: This paper tries to study the effect of geosynthetic inclusion on the improvement of the load-settlement characters of two layered soil. In addition, the effect of geogrid and geotextile in reduction of the required thickness of subbase layer in unpaved roads is studied. Considering the vast application of bearing ratio tests in road construction projects, this test is used in present investigation. Bearing ratio tests were performed on two layered soil including a granular soil layer at the top (as the subbase layer) and a weak clayey soil placed at the bottom (as the subgrade layer). These tests were performed for different conditions including unreinforced and reinforced by geogrid and geotextile and three thicknesses for top layer soil (subbase layer). In the reinforced condition the reinforcing element was placed on the interface of the top granular layer and the beneath clayey layer to study the separation effect of geosynthetics. In all tests the soils (both granular and clayey soil layers) were compacted according to optimum water content. At the end, the diagrams were plotted and were compared with each other. Furthermore, a comparison between geogrids and geotextiles behaviors on two layer soil is done in this paper. The results show an increase in compression strength of reinforced specimen in comparison with unreinforced soil sample. The effect of geosynthetic inclusion reduces by increasing the subbase thickness. In addition it was found that geogrids have more desirable behavior rather than geotextiles due to interlocking with the subbase layer aggregates.
Abstract: This paper proposes an implementation for the
directed diffusion paradigm aids in studying this paradigm-s
operations and evaluates its behavior according to this
implementation. The directed diffusion is evaluated with respect to
the loss percentage, lifetime, end-to-end delay, and throughput.
From these evaluations some suggestions and modifications are
proposed to improve the directed diffusion behavior according to
this implementation with respect to these metrics. The proposed
modifications reflect the effect of local path repair by introducing a
technique called Loop-free Local Path Repair (LLPR) which
improves the directed diffusion behavior especially with respect to
packet loss percentage by about 92.69%. Also LLPR improves the
throughput and end-to-end delay by about 55.31% and 14.06%
respectively, while the lifetime decreases by about 29.79%.
Abstract: The study investigates the mixing performance of
electrokinetically-driven power-law fluids in a microchannel
containing patterned trapezoid blocks. The effects of the geometry
parameters of the patterned trapezoid blocks and the flow behavior
index in the power-law model on the mixing efficiency within the
microchannel are explored. The results show that the mixing efficiency
can be improved by increasing the width of the blocks and extending
the length of upper surface of the blocks. In addition, the results show
that the mixing efficiency increases with an increasing flow behavior
index. Furthermore, it is shown that a heterogeneous patterning of the
zeta potential on the upper surfaces of the trapezoid blocks prompts
the formation of local flow recirculations, and therefore improves the
mixing efficiency. Consequently, it is shown that the mixing
performance improves with an increasing magnitude of the
heterogeneous surface zeta potential.
Abstract: This research aims at development of the Multiple
Intelligences Measurement of Elementary Students. The structural
accuracy test and normality establishment are based on the Multiple
Intelligences Theory of Gardner. This theory consists of eight aspects
namely linguistics, logic and mathematics, visual-spatial relations,
body and movement, music, human relations, self-realization/selfunderstanding
and nature. The sample used in this research consists
of elementary school students (aged between 5-11 years). The size of
the sample group was determined by Yamane Table. The group has
2,504 students. Multistage Sampling was used. Basic statistical
analysis and construct validity testing were done using confirmatory
factor analysis. The research can be summarized as follows; 1.
Multiple Intelligences Measurement consisting of 120 items is
content-accurate. Internal consistent reliability according to the
method of Kuder-Richardson of the whole Multiple Intelligences
Measurement equals .91. The difficulty of the measurement test is
between .39-.83. Discrimination is between .21-.85. 2). The Multiple
Intelligences Measurement has construct validity in a good range,
that is 8 components and all 120 test items have statistical
significance level at .01. Chi-square value equals 4357.7; p=.00 at the
degree of freedom of 244 and Goodness of Fit Index equals 1.00.
Adjusted Goodness of Fit Index equals .92. Comparative Fit Index
(CFI) equals .68. Root Mean Squared Residual (RMR) equals 0.064
and Root Mean Square Error of Approximation equals 0.82. 3). The
normality of the Multiple Intelligences Measurement is categorized
into 3 levels. Those with high intelligence are those with percentiles
of more than 78. Those with moderate/medium intelligence are those
with percentiles between 24 and 77.9. Those with low intelligence
are those with percentiles from 23.9 downwards.
Abstract: In recent years Malaysia has included renewable
energy as an alternative fuel to help in diversifying the country-s
energy reliance on oil, natural gas, coal and hydropower with
biomass and solar energy gaining priority. The scope of this paper is
to look at the designing procedures and analysis of a solar thermal
parabolic trough concentrator by simulation utilizing meteorological
data in several parts of Malaysia. Parameters which include the
aperture area, the diameter of the receiver and the working fluid may
be varied to optimize the design. Aperture area is determined by
considering the width and the length of the concentrator whereas the
geometric concentration ratio (CR) is obtained by considering the
width and diameter of the receiver. Three types of working fluid are
investigated. Theoretically, concentration ratios can be very high in
the range of 10 to 40 000 depending on the optical elements used and
continuous tracking of the sun. However, a thorough analysis is
essential as discussed in this paper where optical precision and
thermal analysis must be carried out to evaluate the performance of
the parabolic trough concentrator as the theoretical CR is not the only
factor that should be considered.
Abstract: Induction motors are being used in greater numbers
throughout a wide variety of industrial and commercial applications
because it provides many benefits and reliable device to convert the
electrical energy into mechanical motion. In some application it-s
desired to control the speed of the induction motor. Because of the
physics of the induction motor the preferred method of controlling its
speed is to vary the frequency of the AC voltage driving the motor. In
recent years, with the microcontroller incorporated into an appliance
it becomes possible to use it to generate the variable frequency AC
voltage to control the speed of the induction motor.
This study investigates the microcontroller based variable
frequency power inverter. the microcontroller is provide the variable
frequency pulse width modulation (PWM) signal that control the
applied voltage on the gate drive, which is provides the required
PWM frequency with less harmonics at the output of the power
inverter.
The fully controlled bridge voltage source inverter has been
implemented with semiconductors power devices isolated gate
bipolar transistor (IGBT), and the PWM technique has been
employed in this inverter to supply the motor with AC voltage.
The proposed drive system for three & single phase power inverter
is simulated using Matlab/Simulink. The Matlab Simulation Results
for the proposed system were achieved with different SPWM. From
the result a stable variable frequency inverter over wide range has
been obtained and a good agreement has been found between the
simulation and hardware of a microcontroller based single phase
inverter.
Abstract: The main objectif of this paper is to present a tool that
we have developed subject to characterize and modelling indoor radio
channel propagation at millimetric wave. The tool is based on the
ray tracing technique (RTT). As, in realistic environment we cannot
neglect the significant impact of Human Body Shadowing and other
objects in motion on indoor 60 GHz propagation channel. Hence,
our proposed model allows a simulation of propagation in a dynamic
indoor environment. First, we describe a model of human body.
Second, RTT with this model is used to simulate the propagation
of millimeter waves in the presence of persons in motion. Results
of the simulation show that this tool gives results in agreement with
those reported in the literature. Specially, the effects of people motion
on temporal channel properties.
Abstract: The mixture formation prior to the ignition process
plays as a key element in the diesel combustion. Parametric studies of
mixture formation and ignition process in various injection parameter
has received considerable attention in potential for reducing
emissions. Purpose of this study is to clarify the effects of injection
pressure on mixture formation and ignition especially during ignition
delay period, which have to be significantly influences throughout the
combustion process and exhaust emissions. This study investigated
the effects of injection pressure on diesel combustion fundamentally
using rapid compression machine. The detail behavior of mixture
formation during ignition delay period was investigated using the
schlieren photography system with a high speed camera. This method
can capture spray evaporation, spray interference, mixture formation
and flame development clearly with real images. Ignition process and
flame development were investigated by direct photography method
using a light sensitive high-speed color digital video camera. The
injection pressure and air motion are important variable that strongly
affect to the fuel evaporation, endothermic and prolysis process
during ignition delay. An increased injection pressure makes spray tip
penetration longer and promotes a greater amount of fuel-air mixing
occurs during ignition delay. A greater quantity of fuel prepared
during ignition delay period thus predominantly promotes more rapid
heat release.
Abstract: Human immunodeficiency virus infection and
acquired immunodeficiency syndrome is a global pandemic with
cases reporting from virtually every country and continues to be a
common infection in developing country like India.
Microalbuminuria is a manifestation of human immunodeficiency
virus associated nephropathy. Therefore, microalbuminuria may be
an early marker of human immunodeficiency virus associated
nephropathy, and screening for its presence may be beneficial. A
strikingly high prevalence of microalbuminuria among human
immunodeficiency virus infected patients has been described in
various studies. Risk factors for clinically significant proteinuria
include African - American race, higher human immunodeficiency
virus ribonucleic acid level and lower CD4 lymphocyte count. The
cardiovascular risk factors of increased systolic blood pressure and
increase fasting blood sugar level are strongly associated with
microalbuminuria in human immunodeficiency virus patient. These
results suggest that microalbuminuria may be a sign of current
endothelial dysfunction and micro-vascular disease and there is
substantial risk of future cardiovascular disease events. Positive
contributing factors include early kidney disease such as human
immunodeficiency virus associated nephropathy, a marker of end
organ damage related to co morbidities of diabetes or hypertension,
or more diffuse endothelial cells dysfunction. Nevertheless after
adjustment for non human immunodeficiency virus factors, human
immunodeficiency virus itself is a major risk factor. The presence of
human immunodeficiency virus infection is independent risk to
develop microalbuminuria in human immunodeficiency virus patient.
Cardiovascular risk factors appeared to be stronger predictors of
microalbuminuria than markers of human immunodeficiency virus
severity person with human immunodeficiency virus infection and
microalbuminuria therefore appear to potentially bear the burden of
two separate damage related to known vascular end organ damage
related to know vascular risk factors, and human immunodeficiency
virus specific processes such as the direct viral infection of kidney
cells.The higher prevalence of microalbuminuria among the human
immunodeficiency virus infected could be harbinger of future
increased risks of both kidney and cardiovascular disease. Further
study defining the prognostic significance of microalbuminuria
among human immunodeficiency virus infected persons will be
essential. Microalbuminuria seems to be a predictor of cardiovascular
disease in diabetic and non diabetic subjects, hence it can also be
used for early detection of micro vascular disease in human
immunodeficiency virus positive patients, thus can help to diagnose
the disease at the earliest.
Abstract: The nickel and gold nanoclusters as supported
catalysts were analyzed by XAS, XRD and XPS in order to
determine their local, global and electronic structure. The present
study has pointed out a strong deformation of the local structure of
the metal, due to its interaction with oxide supports. The average
particle size, the mean squares of the microstrain, the particle size
distribution and microstrain functions of the supported Ni and Au
catalysts were determined by XRD method using Generalized Fermi
Function for the X-ray line profiles approximation. Based on EXAFS
analysis we consider that the local structure of the investigated
systems is strongly distorted concerning the atomic number pairs.
Metal-support interaction is confirmed by the shape changes of the
probability densities of electron transitions: Ni K edge (1s →
continuum and 2p), Au LIII-edge (2p3/2 → continuum, 6s, 6d5/2 and
6d3/2). XPS investigations confirm the metal-support interaction at
their interface.
Abstract: With the rapid popularization of internet services, it is apparent that the next generation terrestrial communication systems must be capable of supporting various applications like voice, video, and data. This paper presents the performance evaluation of turbo- coded mobile terrestrial communication systems, which are capable of providing high quality services for delay sensitive (voice or video) and delay tolerant (text transmission) multimedia applications in urban and suburban areas. Different types of multimedia information require different service qualities, which are generally expressed in terms of a maximum acceptable bit-error-rate (BER) and maximum tolerable latency. The breakthrough discovery of turbo codes allows us to significantly reduce the probability of bit errors with feasible latency. In a turbo-coded system, a trade-off between latency and BER results from the choice of convolutional component codes, interleaver type and size, decoding algorithm, and the number of decoding iterations. This trade-off can be exploited for multimedia applications by using optimal and suboptimal performance parameter amalgamations to achieve different service qualities. The results are therefore proposing an adaptive framework for turbo-coded wireless multimedia communications which incorporate a set of performance parameters that achieve an appropriate set of service qualities, depending on the application's requirements.
Abstract: Bythe development of the Internet, e-commerce has
got very popular between organizations. E-commerce means buying
and selling products and services over the Internet. One of the
challenging issues in e-commerce is how to attract the customers and
how to satisfy them. Therefore, it is important to keep good
relationship with the customers. This paper proposes a new model to
increase the customer satisfaction by introducing live-operator.
Live-operator is a system which is involved both with the customers
and the organization.In this system the customers feelthatthey receive
the service directly from the organization. This model decreases the
response time and the customer loss. Moreover, it increases customer
trust and the ability of organizations.
Abstract: In this study, stress distributions on dental implants
made of functionally graded biomaterials (FGBM) are investigated
numerically. The implant body is considered to be subjected to axial
compression loads. Numerical problem is assumed to be 2D, and
ANSYS commercial software is used for the analysis. The cross
section of the implant thread varies as varying the height (H) and the
width (t) of the thread. According to thread dimensions of implant
and material properties of FGBM, equivalent stress distribution on
the implant is determined and presented with contour plots along
with the maximum equivalent stress values. As a result, with
increasing material gradient parameter (n), the equivalent stress
decreases, but the minimum stress distribution increases. Maximum
stress values decrease with decreasing implant radius (r). Maximum
von Mises stresses increases with decreasing H when t is constant.
On the other hand, the stress values are not affected by variation of t
in the case of H = constant.
Abstract: Combustion of sprays is of technological importance, but its flame behavior is not fully understood. Furthermore, the multiplicity of dependent variables such as pressure, temperature, equivalence ratio, and droplet sizes complicates the study of spray combustion. Fundamental study on the influence of the presence of liquid droplets has revealed that laminar flames within aerosol mixtures more readily become unstable than for gaseous ones and this increases the practical burning rate. However, fundamental studies on turbulent flames of aerosol mixtures are limited particularly those under near mono-dispersed droplet conditions. In the present work, centrally ignited expanding flames at near atmospheric pressures are employed to quantify the burning rates in gaseous and aerosol flames. Iso-octane-air aerosols are generated by expansion of the gaseous pre-mixture to produce a homogeneously distributed suspension of fuel droplets. The effects of the presence of droplets and turbulence velocity in relation to the burning rates of the flame are also investigated.
Abstract: Corner detection and optical flow are common techniques for feature-based video stabilization. However, these algorithms are computationally expensive and should be performed at a reasonable rate. This paper presents an algorithm for discarding irrelevant feature points and maintaining them for future use so as to improve the computational cost. The algorithm starts by initializing a maintained set. The feature points in the maintained set are examined against its accuracy for modeling. Corner detection is required only when the feature points are insufficiently accurate for future modeling. Then, optical flows are computed from the maintained feature points toward the consecutive frame. After that, a motion model is estimated based on the simplified affine motion model and least square method, with outliers belonging to moving objects presented. Studentized residuals are used to eliminate such outliers. The model estimation and elimination processes repeat until no more outliers are identified. Finally, the entire algorithm repeats along the video sequence with the points remaining from the previous iteration used as the maintained set. As a practical application, an efficient video stabilization can be achieved by exploiting the computed motion models. Our study shows that the number of times corner detection needs to perform is greatly reduced, thus significantly improving the computational cost. Moreover, optical flow vectors are computed for only the maintained feature points, not for outliers, thus also reducing the computational cost. In addition, the feature points after reduction can sufficiently be used for background objects tracking as demonstrated in the simple video stabilizer based on our proposed algorithm.
Abstract: The Information and Communication Technologies
(ICTs), and the Wide World Web (WWW) have fundamentally
altered the practice of teaching and learning world wide. Many
universities, organizations, colleges and schools are trying to apply
the benefits of the emerging ICT. In the early nineties the term
learning object was introduced into the instructional technology
vernacular; the idea being that educational resources could be broken
into modular components for later combination by instructors,
learners, and eventually computes into larger structures that would
support learning [1]. However in many developing countries, the use
of ICT is still in its infancy stage and the concept of learning object
is quite new. This paper outlines the learning object design
considerations for developing countries depending on learning
environment.
Abstract: Wetting characteristics of reactive (Sn–0.7Cu solder)
and non– reactive (castor oil) wetting of liquids on Cu and Ag plated
Al substrates have been investigated. Solder spreading exhibited
capillary, gravity and viscous regimes. Oils did not exhibit noticeable
spreading regimes. Solder alloy showed better wettability on Ag
coated Al substrate compared to Cu plating. In the case of castor oil,
Cu coated Al substrate exhibited good wettability as compared to Ag
coated Al substrates. The difference in wettability during reactive
wetting of solder and non–reactive wetting of oils is attributed to the
change in the surface energies of Al substrates brought about by the
formation of intermetallic compounds (IMCs).