Abstract: The main aim of a communication system is to
achieve maximum performance. In Cognitive Radio any user or
transceiver has ability to sense best suitable channel, while channel is
not in use. It means an unlicensed user can share the spectrum of a
licensed user without any interference. Though, the spectrum sensing
consumes a large amount of energy and it can reduce by applying
various artificial intelligent methods for determining proper spectrum
holes. It also increases the efficiency of Cognitive Radio Network
(CRN). In this survey paper we discuss the use of different learning
models and implementation of Artificial Neural Network (ANN) to
increase the learning and decision making capacity of CRN without
affecting bandwidth, cost and signal rate.
Abstract: Future flood can be predicted using the probable
maximum flood (PMF). PMF is calculated using the historical
discharge or rainfall data considering the other climatic parameters
remaining stationary. However climate is changing globally and the
key climatic variables are temperature, evaporation, rainfall and sea
level rise are likely to change. To develop scenarios to a basin or
catchment scale these important climatic variables should be
considered. Nowadays scenario based on climatic variables is more
suitable than PMF. Six scenarios were developed for a large Fitzroy
basin and presented in this paper.
Abstract: In the scope of application of technical textiles, Non-
Crimp Fabrics are increasingly used. In general, NCF exhibit
excellent load bearing properties, but caused by the manufacturing
process, there are some remaining disadvantages which have to be
reduced. Regarding to this, a novel technique of processing NCF was
developed substituting the binding-thread by an adhesive. This stitchfree
method requires new manufacturing concept as well as new basic
methods to prove adhesion of glue at fibres and textiles. To improve
adhesion properties and the wettability of carbon-fibres by the
adhesive, oxy-fluorination was used. The modification of carbonfibres
by oxy-fluorination was investigated via scanning electron
microscope, X-ray photoelectron spectroscopy and single fibre
tensiometry. Special tensile tests were developed to determine the
maximum force required for detachment.
Abstract: Proof of controlling crack width is a basic condition
for securing suitable performance in serviceability limit state. The
cracking in concrete can occur at any time from the casting of time to
the years after the concrete has been set in place. Most codes struggle
with offering procedure for crack width calculation. There is lack in
availability of design charts for designers to compute crack width
with ease. The focus of the study is to utilize design charts and
parametric equations in calculating crack width with minimum error.
The paper contains a simplified procedure to calculate crack width
for reinforced concrete (RC) sections subjected to bending with axial
tensile force following the guidelines of Euro code [DS EN-1992-1-1
& DS EN-1992-1-2]. Numerical examples demonstrate the
application of the suggested procedure. Comparison with parallel
analytical tools supports the validity of result and show the
percentage deviation of crack width in both the procedures. The
technique is simple, user friendly and ready to evolve for a greater
spectrum of section sizes and materials.
Abstract: The Roma (Gypsies) is a transnational minority with a
high degree of consanguineous marriages. Similar to other
genetically isolated founder populations, the Roma harbor a number
of unique or rare genetic disorders. This paper discusses about a rare
form of Charcot-Marie-Tooth disease – type 4G (CMT4G), also
called Hereditary Motor and Sensory Neuropathy type Russe, an
autosomal recessive disease caused by mutation private to Roma
characterized by abnormally increased density of non-myelinated
axons. CMT4G was originally found in Bulgarian Roma and in 2009
two putative causative mutations in the HK1 gene were identified.
Since then, several cases were reported in Roma families mainly
from Bulgaria and Spain. Here we present a Slovak Roma family in
which CMT4G was diagnosed on the basis of clinical examination
and genetic testing. This case is a further proof of the role of the HK1
gene in pathogenesis of the disease. It confirms that mutation in the
HK1 gene is a common cause of autosomal recessive CMT disease in
Roma and should be considered as a common part of a diagnostic
procedure.
Abstract: It is difficult to study the effect of various variables on
cycle fitting through actual experiment. To overcome such difficulty,
the forward dynamics of a musculoskeletal model was applied to cycle
fitting in this study. The measured EMG data weres compared with the
muscle activities of the musculoskeletal model through forward
dynamics. EMG data were measured from five cyclists who do not
have musculoskeletal diseases during three minutes pedaling with a
constant load (150 W) and cadence (90 RPM). The muscles used for
the analysis were the Vastus Lateralis (VL), Tibialis Anterior (TA),
Bicep Femoris (BF), and Gastrocnemius Medial (GM). Person’s
correlation coefficients of the muscle activity patterns, the peak timing
of the maximum muscle activities, and the total muscle activities were
calculated and compared. BIKE3D model of AnyBody (Anybodytech,
Denmark) was used for the musculoskeletal model simulation. The
comparisons of the actual experiments with the simulation results
showed significant correlations in the muscle activity patterns (VL:
0.789, TA: 0.503, BF: 0.468, GM: 0.670). The peak timings of the
maximum muscle activities were distributed at particular phases. The
total muscle activities were compared with the normalized muscle
activities, and the comparison showed about 10% difference in the VL
(+10%), TA (+9.7%), and BF (+10%), excluding the GM (+29.4%).
Thus, it can be concluded that muscle activities of model &
experiment showed similar results. The results of this study indicated
that it was possible to apply the simulation of further improved
musculoskeletal model to cycle fitting.
Abstract: We have developed a new computer program in
Fortran 90, in order to obtain numerical solutions of a system
of Relativistic Magnetohydrodynamics partial differential equations
with predetermined gravitation (GRMHD), capable of simulating
the formation of relativistic jets from the accretion disk of matter
up to his ejection. Initially we carried out a study on numerical
methods of unidimensional Finite Volume, namely Lax-Friedrichs,
Lax-Wendroff, Nessyahu-Tadmor method and Godunov methods
dependent on Riemann problems, applied to equations Euler in
order to verify their main features and make comparisons among
those methods. It was then implemented the method of Finite
Volume Centered of Nessyahu-Tadmor, a numerical schemes that
has a formulation free and without dimensional separation of
Riemann problem solvers, even in two or more spatial dimensions,
at this point, already applied in equations GRMHD. Finally, the
Nessyahu-Tadmor method was possible to obtain stable numerical
solutions - without spurious oscillations or excessive dissipation -
from the magnetized accretion disk process in rotation with respect
to a central black hole (BH) Schwarzschild and immersed in a
magnetosphere, for the ejection of matter in the form of jet over a
distance of fourteen times the radius of the BH, a record in terms
of astrophysical simulation of this kind. Also in our simulations,
we managed to get substructures jets. A great advantage obtained
was that, with the our code, we got simulate GRMHD equations in
a simple personal computer.
Abstract: The most important component affecting the
efficiency of photovoltaic power systems are solar panels. In other
words, efficiency of these systems are significantly affected due to
the being low efficiency of solar panel. Thus, solar panels should be
operated under maximum power point conditions through a power
converter. In this study, design of boost converter has been carried
out with maximum power point tracking (MPPT) algorithm which is
incremental conductance (Inc-Cond). By using this algorithm,
importance of power converter in MPPT hardware design, impacts of
MPPT operation have been shown. It is worth noting that initial
operation point is the main criteria for determining the MPPT
performance. In addition, it is shown that if value of load resistance is
lower than critical value, failure operation is realized. For these
analyzes, direct duty control is used for simplifying the control.
Abstract: In this study the instability problem of a modified
Taylor-Couette flow between two vertical coaxial cylinders of radius
R1, R2 is considered. The modification is based on the wavy shape of
the inner cylinder surface, where inner cylinders with different
surface amplitude and wavelength are used. The study aims to
discover the effect of the inner surface geometry on the instability
phenomenon that undergoes Taylor-Couette flow. The study reveals
that the transition processes depends strongly on the amplitude and
wavelength of the inner cylinder surface and resulting in flow
instabilities that are strongly different from that encountered in the
case of the classical Taylor-Couette flow.
Abstract: In this paper, effect of marginal quality groundwater
on yield of cotton crop and soil salinity was studied. In this
connection, three irrigation treatments each with four replications
were applied. These treatments were i) use of canal water (T1), ii) use
of marginal quality groundwater from tubewell (T2), and iii)
conjunctive use by mixing with the ratio of 1:1 of canal water and
marginal quality tubewell water (T3).
Water was applied to the crop cultivated in Kharif season 2011; its
quantity has been measured using cut-throat flume. Total 11 watering
each of 50 mm depth have been applied from 20th April to 20th July,
2011. Further, irrigations were stopped due to monsoon rainfall up to
crop harvesting.
Maximum crop yield (seed cotton) was observed under T1 which
was 1,517 kg/ha followed by T3 (mixed canal and tubewell water)
having 1009 kg/ha and T2 i.e. marginal quality groundwater having
709 kg/ha. This concludes that crop yield in T2 and T3 in comparison
to T1was reduced by about 53 and 30% respectively.
It has been observed that yield of cotton crop is below potential
limit for three treatments due to unexpected rainfall at the time of full
flowering season; thus the yield was adversely affected.
However, salt deposition in soil profiles was not observed that is
due to leaching effect of heavy rainfall occurred during monsoon
season.
Abstract: The paper examines the interaction between the
environmental taxation, size of government spending on
environmental protection and greenhouse gas emissions and gross
inland energy consumption. The aim is to analyze the effects of
environmental taxation and government spending on environmental
protection as an environmental policy instruments on greenhouse gas
emissions and gross inland energy consumption in the EU15. The
empirical study is performed using a VAR approach with the
application of aggregated data of EU15 over the period 1995 to 2012.
The results provide the evidence that the reactions of greenhouse gas
emission and gross inland energy consumption to the shocks of
environmental policy instruments are strong, mainly in the short term
and decay to zero after about 8 years. Further, the reactions of the
environmental policy instruments to the shocks of greenhouse gas
emission and gross inland energy consumption are also strong in the
short term, however with the deferred effects. In addition, the results
show that government spending on environmental protection together
with gross inland energy consumption has stronger effect on
greenhouse gas emissions than environmental taxes in EU15 over the
examined period.
Abstract: Nowadays, Photovoltaic-PV Farms/ Parks and large
PV-Smart Grid Interface Schemes are emerging and commonly
utilized in Renewable Energy distributed generation. However, PVhybrid-
Dc-Ac Schemes using interface power electronic converters
usually has negative impact on power quality and stabilization of
modern electrical network under load excursions and network fault
conditions in smart grid. Consequently, robust FACTS based
interface schemes are required to ensure efficient energy utilization
and stabilization of bus voltages as well as limiting switching/fault
onrush current condition. FACTS devices are also used in smart grid-
Battery Interface and Storage Schemes with PV-Battery Storage
hybrid systems as an elegant alternative to renewable energy
utilization with backup battery storage for electric utility energy and
demand side management to provide needed energy and power
capacity under heavy load conditions. The paper presents a robust
interface PV-Li-Ion Battery Storage Interface Scheme for
Distribution/Utilization Low Voltage Interface using FACTS
stabilization enhancement and dynamic maximum PV power tracking
controllers.
Digital simulation and validation of the proposed scheme is done
using MATLAB/Simulink software environment for Low Voltage-
Distribution/Utilization system feeding a hybrid Linear-Motorized
inrush and nonlinear type loads from a DC-AC Interface VSC-6-
pulse Inverter Fed from the PV Park/Farm with a back-up Li-Ion
Storage Battery.
Abstract: In this paper a new design of a broadband microwave
power limiter is presented and validated into simulation by using
ADS software (Advanced Design System) from Agilent technologies.
The final circuit is built on microstrip lines by using identical Zero
Bias Schottky diodes. The power limiter is designed by Associating 3
stages Schottky diodes. The obtained simulation results permit to
validate this circuit with a threshold input power level of 0 dBm until
a maximum input power of 30 dBm.
Abstract: In this paper, we present a robust algorithm to recognize extracted text from grocery product images captured by mobile phone cameras. Recognition of such text is challenging since text in grocery product images varies in its size, orientation,
style, illumination, and can suffer from perspective distortion.
Pre-processing is performed to make the characters scale and
rotation invariant. Since text degradations can not be appropriately
defined using well-known geometric transformations such
as translation, rotation, affine transformation and shearing, we
use the whole character black pixels as our feature vector.
Classification is performed with minimum distance classifier
using the maximum likelihood criterion, which delivers very
promising Character Recognition Rate (CRR) of 89%. We
achieve considerably higher Word Recognition Rate (WRR) of
99% when using lower level linguistic knowledge about product
words during the recognition process.
Abstract: In this paper, we present preconditioned generalized
accelerated overrelaxation (GAOR) methods for solving certain
nonsingular linear system. We compare the spectral radii of the
iteration matrices of the preconditioned and the original methods. The
comparison results show that the preconditioned GAOR methods
converge faster than the GAOR method whenever the GAOR method
is convergent. Finally, we give two numerical examples to confirm our
theoretical results.
Abstract: Taking the design tolerance into account, this paper
presents a novel efficient approach to generate iso-scallop tool path for
five-axis strip machining with a barrel cutter. The cutter location is
first determined on the scallop surface instead of the design surface,
and then the cutter is adjusted to locate the optimal tool position based
on the differential rotation of the tool axis and satisfies the design
tolerance simultaneously. The machining strip width and error are
calculated with the aid of the grazing curve of the cutter. Based on the
proposed tool positioning algorithm, the tool paths are generated by
keeping the scallop height formed by adjacent tool paths constant. An
example is conducted to confirm the validity of the proposed method.
Abstract: The IEEE 802.22 working group aims to drive the
Digital Video Broadcasting-Terrestrial (DVB-T) bands for data
communication to the rural area without interfering the TV broadcast.
In this paper, we arrive at a closed-form expression for average
detection probability of Fusion center (FC) with multiple antenna
over the κ − μ fading channel model. We consider a centralized
cooperative multiple antenna network for reporting. The DVB-T
samples forwarded by the secondary user (SU) were combined using
Maximum ratio combiner at FC, an energy detection is performed
to make the decision. The fading effects of the channel degrades
the detection probability of the FC, a generalized independent and
identically distributed (IID) κ − μ and an additive white Gaussian
noise (AWGN) channel is considered for reporting and sensing
respectively. The proposed system performance is verified through
simulation results.
Abstract: At present, the evaluation of voltage stability
assessment experiences sizeable anxiety in the safe operation of
power systems. This is due to the complications of a strain power
system. With the snowballing of power demand by the consumers
and also the restricted amount of power sources, therefore, the system
has to perform at its maximum proficiency. Consequently, the
noteworthy to discover the maximum ability boundary prior to
voltage collapse should be undertaken. A preliminary warning can be
perceived to evade the interruption of power system’s capacity. The
effectiveness of line voltage stability indices (LVSI) is differentiated
in this paper. The main purpose of the indices used is to predict the
proximity of voltage instability of the electric power system. On the
other hand, the indices are also able to decide the weakest load buses
which are close to voltage collapse in the power system. The line
stability indices are assessed using the IEEE 14 bus test system to
validate its practicability. Results demonstrated that the implemented
indices are practically relevant in predicting the manifestation of
voltage collapse in the system. Therefore, essential actions can be
taken to dodge the incident from arising.
Abstract: Femtocells are regarded as a milestone for next
generation cellular networks. As femtocells are deployed in an
unplanned manner, there is a chance of assigning same resource to
neighboring femtocells. This scenario may induce co-channel
interference and may seriously affect the service quality of
neighboring femtocells. In addition, the dominant transmit power of a
femtocell will induce co-tier interference to neighboring femtocells.
Thus to jointly handle co-tier and co-channel interference, we
propose an interference-free power and resource block allocation
(IFPRBA) algorithm for closely located, closed access femtocells.
Based on neighboring list, inter-femto-base station distance and
uplink noise power, the IFPRBA algorithm assigns non-interfering
power and resource to femtocells. The IFPRBA algorithm also
guarantees the quality of service to femtouser based on the
knowledge of resource requirement, connection type, and the
tolerable delay budget. Simulation result shows that the interference
power experienced in IFPRBA algorithm is below the tolerable
interference power and hence the overall service success ratio, PRB
efficiency and network throughput are maximum when compared to
conventional resource allocation framework for femtocell (RAFF)
algorithm.
Abstract: This paper investigates the viability of using carbon
fiber reinforced epoxy composites modified with carbon nanotubes to
strengthening reinforced concrete (RC) columns. Six RC columns
was designed and constructed according to ASCE standards. The
columns were wrapped using carbon fiber sheets impregnated with
either neat epoxy or CNTs modified epoxy. These columns were then
tested under concentric axial loading. Test results show that;
compared to the unwrapped specimens; wrapping concrete columns
with carbon fiber sheet embedded in CNTs modified epoxy resulted
in an increase in its axial load resistance, maximum displacement,
and toughness values by 24%, 109% and 232%, respectively. These
results reveal that adding CNTs into epoxy resin enhanced the
confinement effect, specifically, increased the axial load resistance,
maximum displacement, and toughness values by 11%, 6%, and
19%, respectively compared with columns strengthening with carbon
fiber sheet embedded in neat epoxy.