Abstract: Total hip replacement had been one of the most
successful operations in hip arthritis surgery. The purpose of this
research had been to develop a dynamic hip contact of Thai femoral
bone to analyze the stress distribution on the implant and the strain
distribution on the bone model under daily activities and compared
with the static load simulation. The results showed the different of
maximum von Mises stress 0.14 percent under walking and 0.03
percent under climbing stair condition and the different of equivalent
total strain 0.52 percent under walking and 0.05 percent under
climbing stair condition. The muscular forces should be evaluated
with dynamic condition to reduce the maximum von Mises stress and
equivalent total strain.
Abstract: The pullout strength had an effect on the stability of
plate screw fixation when inserted in the cervical spine. Nine
different titanium alloy bone screws were used to test the pullout
strength through finite element analysis. The result showed that the
Moss Miami I can bear the highest pullout force at 1,075 N, which
causes the maximum von Mises stress at 858.87 MPa, a value over
the yield strength of titanium. The bone screw should have large
outer diameter, core diameter and proximal root radius to increase the
pullout strength.
Abstract: Composite material based on Fe3Si micro-particles
and Mn-Zn nano-ferrite was prepared using powder metallurgy
technology. The sol-gel followed by autocombustion process was
used for synthesis of Mn0.8Zn0.2Fe2O4 ferrite. 3 wt.% of mechanically
milled ferrite was mixed with Fe3Si powder alloy. Mixed micro-nano
powder system was homogenized by the Resonant Acoustic Mixing
using ResodynLabRAM Mixer. This non-invasive homogenization
technique was used to preserve spherical morphology of Fe3Si
powder particles. Uniaxial cold pressing in the closed die at pressure
600 MPa was applied to obtain a compact sample. Microwave
sintering of green compact was realized at 800°C, 20 minutes, in air.
Density of the powders and composite was measured by
Hepycnometry. Impulse excitation method was used to measure
elastic properties of sintered composite. Mechanical properties were
evaluated by measurement of transverse rupture strength (TRS) and
Vickers hardness (HV). Resistivity was measured by 4 point probe
method. Ferrite phase distribution in volume of the composite was
documented by metallographic analysis.
It has been found that nano-ferrite particle distributed among
micro- particles of Fe3Si powder alloy led to high relative density
(~93%) and suitable mechanical properties (TRS >100 MPa, HV
~1GPa, E-modulus ~140 GPa) of the composite. High electric
resistivity (R~6.7 ohm.cm) of prepared composite indicate their
potential application as soft magnetic material at medium and high
frequencies.
Abstract: Microbial fuel cells (MFCs) represent a promising
technology for simultaneous bioelectricity generation and wastewater
treatment. Catalysts are significant portions of the cost of microbial
fuel cell cathodes. Many materials have been tested as aqueous
cathodes, but air-cathodes are needed to avoid energy demands for
water aeration. The sluggish oxygen reduction reaction (ORR) rate at
air cathode necessitates efficient electrocatalyst such as carbon
supported platinum catalyst (Pt/C) which is very costly. Manganese
oxide (MnO2) was a representative metal oxide which has been
studied as a promising alternative electrocatalyst for ORR and has
been tested in air-cathode MFCs. However the single MnO2 has poor
electric conductivity and low stability. In the present work, the MnO2
catalyst has been modified by doping Pt nanoparticle. The goal of the
work was to improve the performance of the MFC with minimum Pt
loading. MnO2 and Pt nanoparticles were prepared by hydrothermal
and sol gel methods, respectively. Wet impregnation method was
used to synthesize Pt/MnO2 catalyst. The catalysts were further used
as cathode catalysts in air-cathode cubic MFCs, in which anaerobic
sludge was inoculated as biocatalysts and palm oil mill effluent
(POME) was used as the substrate in the anode chamber. The asprepared
Pt/MnO2 was characterized comprehensively through field
emission scanning electron microscope (FESEM), X-Ray diffraction
(XRD), X-ray photoelectron spectroscopy (XPS), and cyclic
voltammetry (CV) where its surface morphology, crystallinity,
oxidation state and electrochemical activity were examined,
respectively. XPS revealed Mn (IV) oxidation state and Pt (0)
nanoparticle metal, indicating the presence of MnO2 and Pt.
Morphology of Pt/MnO2 observed from FESEM shows that the
doping of Pt did not cause change in needle-like shape of MnO2
which provides large contacting surface area. The electrochemical
active area of the Pt/MnO2 catalysts has been increased from 276 to
617 m2/g with the increase in Pt loading from 0.2 to 0.8 wt%. The
CV results in O2 saturated neutral Na2SO4 solution showed that
MnO2 and Pt/MnO2 catalysts could catalyze ORR with different
catalytic activities. MFC with Pt/MnO2 (0.4 wt% Pt) as air cathode
catalyst generates a maximum power density of 165 mW/m3, which
is higher than that of MFC with MnO2 catalyst (95 mW/m3). The
open circuit voltage (OCV) of the MFC operated with MnO2 cathode
gradually decreased during 14 days of operation, whereas the MFC
with Pt/MnO2 cathode remained almost constant throughout the
operation suggesting the higher stability of the Pt/MnO2 catalyst.
Therefore, Pt/MnO2 with 0.4 wt% Pt successfully demonstrated as an
efficient and low cost electrocatalyst for ORR in air cathode MFC with higher electrochemical activity, stability and hence enhanced
performance.
Abstract: Newly synthesized Polypropylene-g-Polyethylene
glycol polymer was first time used for a compartment-less enzymatic
fuel cell. Working electrodes based on Polypropylene-g-Polyethylene
glycol were operated as unmediated and mediated system (with
ferrocene and gold/cobalt oxide nanoparticles). Glucose oxidase and
bilirubin oxidase was selected as anodic and cathodic enzyme,
respectively. Glucose was used as fuel in a single-compartment and
membrane-less cell. Maximum power density was obtained as 0.65
nW cm-2, 65 nW cm-2 and 23500 nW cm-2 from the unmediated,
ferrocene and gold/cobalt oxide modified polymeric film,
respectively. Power density was calculated to be ~16000 nW cm-2 for
undiluted wastewater sample with gold/cobalt oxide nanoparticles
including system.
Abstract: This study was developed to compare the behavior
and the ability of polymer foam composites towards sound absorption
test of Shorea leprosula wood (SL) of acid hydrolysis treatment with
particle size
Abstract: A numerical study of natural convection heat transfer
in water filled cavity has been examined in 3-Dfor single phase liquid
cooling system by using an array of parallel plate fins mounted to one
wall of a cavity. The heat generated by a heat source represents a
computer CPU with dimensions of 37.5∗37.5mm mounted on
substrate. A cold plate is used as a heat sink installed on the opposite
vertical end of the enclosure. The air flow inside the computer case is
created by an exhaust fan. A turbulent air flow is assumed and k-ε
model is applied. The fins are installed on the substrate to enhance
the heat transfer. The applied power energy range used is between 15
- 40W. In order to determine the thermal behaviour of the cooling
system, the effect of the heat input and the number of the parallel
plate fins are investigated. The results illustrate that as the fin number
increases the maximum heat source temperature decreases. However,
when the fin number increases to critical value the temperature start
to increase due to the fins are too closely spaced and that cause the
obstruction of water flow. The introduction of parallel plate fins
reduces the maximum heat source temperature by 10% compared to
the case without fins. The cooling system maintains the maximum
chip temperature at 64.68°C when the heat input was at 40W that is
much lower than the recommended computer chips limit temperature
of no more than 85°C and hence the performance of the CPU is
enhanced.
Abstract: Human motion capture has become one of the major
area of interest in the field of computer vision. Some of the major
application areas that have been rapidly evolving include the
advanced human interfaces, virtual reality and security/surveillance
systems. This study provides a brief overview of the techniques and
applications used for the markerless human motion capture, which
deals with analyzing the human motion in the form of mathematical
formulations. The major contribution of this research is that it
classifies the computer vision based techniques of human motion
capture based on the taxonomy, and then breaks its down into four
systematically different categories of tracking, initialization, pose
estimation and recognition. The detailed descriptions and the
relationships descriptions are given for the techniques of tracking and
pose estimation. The subcategories of each process are further
described. Various hypotheses have been used by the researchers in
this domain are surveyed and the evolution of these techniques have
been explained. It has been concluded in the survey that most
researchers have focused on using the mathematical body models for
the markerless motion capture.
Abstract: The objective of this study was to identify the optimal
level of partial replacement of Portland cement by the ashes
originating from burning straw and bagasse from sugar cane (ASB).
Order to this end, were made five series of flat plates and cylindrical
bodies: control and others with the partial replacement in 20, 30, 40
and 50% of ASB in relation to the mass of the Ordinary Portland
cement, and conducted a mechanical testing of simple axial
compression (cylindrical bodies) and the four-point bending (flat
plates) and determined water absorption (WA), bulk density (BD)
and apparent void volume (AVV) on both types of specimens. Based
on the data obtained, it may be noted that the control treatment
containing only Portland cement, obtained the best results. However,
the cylindrical bodies with 20% ashes showed better results
compared to the other treatments. And in the formulations plates, the
treatment which showed the best results was 30% cement
replacement by ashes.
Abstract: This paper examines how “Zakat” provides fair
income redistribution and aids the struggle against poverty. Providing
fair income redistribution and combating poverty constitutes some of
the fundamental tasks performed by countries all over the world.
Each country seeks a solution for these problems according to their
political, economic and administrative styles through applying
various economic and financial policies. The same situation can be
handled via “zakat” association in Islam. Nowadays, we observe
different versions of “zakat” in developed countries. Applications
such as negative income tax denote merely a different form of
“zakat” that is being applied almost in the same way but under
changed names. However, the minimum values to donate under zakat
(e.g. 85 gr. gold and 40 animals) get altered and various amounts are
put into practice. It might be named as negative income tax instead of
zakat, nonetheless, these applications are based on the Holy Koran
and the hadith released 1400 years ago. Besides, considering the
savage and slavery in the world at those times, we might easily
recognize the true value of the zakat being applied for the first time
then in the Islamic system. Through zakat, governments are able to
transfer incomes to the poor as a means of enabling them achieve the
minimum standard of living required. With regards to who benefits
from the Zakat, an objective and fair criteria was used to determine
who benefits from the zakat contrary to the notion that it was based
on peoples’ own choices. Since the zakat is obligatory, the transfers
do not get forwarded directly but via the government and get
distributed, which requires vast governmental organizations. Through
the application of Zakat, reduced levels of poverty can be achieved
and also ensure the fair income redistribution.
Abstract: Biofuels production has come forth as a future
technology to combat the problem of depleting fossil fuels. Bio-based
ethanol production from enzymatic lignocellulosic biomass
degradation serves an efficient method and catching the eye of
scientific community. High cost of the enzyme is the major obstacle
in preventing the commercialization of this process. Thus main
objective of the present study was to optimize composition of
medium components for enhancing cellulase production by newly
isolated strain of Bacillus tequilensis. Nineteen factors were taken
into account using statistical Plackett-Burman Design. The significant
variables influencing the cellulose production were further employed
in statistical Response Surface Methodology using Central
Composite Design for maximizing cellulase production. The
optimum medium composition for cellulase production was: peptone
(4.94 g/L), ammonium chloride (4.99 g/L), yeast extract (2.00 g/L),
Tween-20 (0.53 g/L), calcium chloride (0.20 g/L) and cobalt chloride
(0.60 g/L) with pH 7, agitation speed 150 rpm and 72 h incubation at
37oC. Analysis of variance (ANOVA) revealed high coefficient of
determination (R2) of 0.99. Maximum cellulase productivity of 11.5
IU/ml was observed against the model predicted value of 13 IU/ml.
This was found to be optimally active at 60oC and pH 5.5.
Abstract: Macro invertebrates have been used to monitor
organic pollution in rivers and streams. Several biotic indices based
on macro invertebrates have been developed over the years including
the Biological Monitoring Working Party (BMWP). A new biotic
index, the Gammarus:Asellus ratio has been recently proposed as an
index of organic pollution. This study tested the validity of the
Gammarus:Asellus ratio as an index of organic pollution, by
examining the relationship between the Gammarus:Asellus ratio and
physical chemical parameters, and other biotic indices such as
BMWP and, Average Score Per Taxon (ASPT) from lakes and
streams at Markeaton Park, Allestree Park and Kedleston Hall,
Derbyshire. Macro invertebrates were sampled using the standard
five minute kick sampling techniques physical and chemical
environmental variables were obtained based on standard sampling
techniques. Eighteen sites were sampled, six sites from Markeaton
Park (three sites across the stream and three sites across the lake). Six
sites each were also sampled from Allestree Park and Kedleston Hall
lakes. The Gammarus:Asellus ratio showed an opposite significant
positive correlations with parameters indicative of organic pollution
such as the level of nitrates, phosphates, and calcium and also
revealed a negatively significant correlations with other biotic indices
(BMWP/ASPT). The BMWP score correlated positively significantly
with some water quality parameters such as dissolved oxygen and
flow rate, but revealed no correlations with other chemical
environmental variables. The BMWP score was significantly higher
in the stream than the lake in Markeaton Park, also The ASPT scores
appear to be significantly higher in the upper Lakes than the middle
and lower lakes. This study has further strengthened the use of
BMWP/ASPT score as an index of organic pollution. But additional
application is required to validate the use of Gammarus:Asellus as a
rapid bio monitoring tool.
Abstract: Near-infrared spectroscopy (NIRS) has been widely
used as a non-invasive method to measure brain activity, but it is
corrupted by baseline drift noise. Here we present a method to measure
regional cerebral blood flow as a derivative of NIRS output. We
investigate whether, when listening to languages, blood flow can
reasonably localize and represent regional brain activity or not. The
prefrontal blood flow distribution pattern when advanced
second-language listeners listened to a second language (L2) was most
similar to that when listening to their first language (L1) among the
patterns of mean and standard deviation. In experiments with 25
healthy subjects, the maximum blood flow was localized to the left
BA46 of advanced listeners. The blood flow presented is robust to
baseline drift and stably localizes regional brain activity.
Abstract: For the treatment of acute and chronic lung diseases it is preferred to deliver medicaments by inhalation. The drug is delivered directly to tracheobronchial tree. This way allows the given medicament to get directly into the place of action and it makes rapid onset of action and maximum efficiency. The transport of aerosol particles in the particular part of the lung is influenced by their size, anatomy of the lungs, breathing pattern and airway resistance. This article deals with calculation of airway resistance in the lung model of Horsfield. It solves the problem of determination of the pressure losses in bifurcation and thus defines the pressure drop at a given location in the bronchial tree. The obtained data will be used as boundary conditions for transport of aerosol particles in a central part of bronchial tree realized by Computational Fluid Dynamics (CFD) approach. The results obtained from CFD simulation will allow us to provide information on the required particle size and optimal inhalation technique for particle transport into particular part of the lung.
Abstract: The temperature dependence of wettability (wetting
angle, Θ (T)) for Ag-based melts on graphite and Al2O3 substrates is
compared. Typical alloying effects are found, as the Ag host metal is
gradually replaced by various metallic elements. The essence of
alloying lies in the change of the electron/atom (e/a) ratio. This ratio
is also manifested in the shift of wetting angles on the same substrate.
Nevertheless, the effects are partially smeared by other
(metallurgical) factors, like the interaction between the oxygenalloying
elements and by the graphite substrate-oxygen interaction. In
contrast, such effects are not pronounced in the case of Al2O3
substrates. As a consequence, Θ(T) exhibits an opposite trend in the
case of two substrates. Crossovers of the Θ(T) curves were often
found. The positions of crossovers depend on the chemical character
and concentration of solute atoms. Segregation and epitaxial texture
formation after solidification were also observed in certain alloy
drops, especially in high concentration range. This phenomenon is
not yet explained in every detail.
Abstract: Since columns are the most important elements of the
structures, failure of one column in a critical location can cause a
progressive collapse. In this respect, the repair and strengthening of
columns is a very important subject to reduce the building failure and
to keep the columns capacity. Twenty columns with different
parameters is tested and analysis. Eleven typical confined reinforced
concrete (RC) columns with different types of techniques are
assessment. And also, four confined concrete columns with plastic
tube (PVC) are tested with and with four paralleling tested of
unconfined plain concrete. The techniques of confined RC columns
are mortar strengthening, Steel rings strengthening, FRP
strengthening. Moreover, the technique of confined plain concrete
(PC) column is used PVC tubes. The columns are tested under
uniaxial compressive loads studied the effect of confinement on the
structural behavior of circular RC columns. Test results for each
column are presented in the form of crack patterns, stress-strain
curves. Test results show that confining of the RC columns using
different techniques of strengthening results significant improvement
of the general behavior of the columns and can used in construction.
And also, tested confined PC columns with PVC tubes results shown
that the confined PC with PVC tubes can be used in economical
building. The theoretical model for predicted column capacity is
founded with experimental factor depends on the confined techniques
used and the strain reduction.
Abstract: The dielectric properties and ionic conductivity of
novel "ceramic state" polymer electrolytes for high capacity lithium
battery are characterized by Radio frequency and Microwave
methods in two broad frequency ranges from 50 Hz to 20 KHz and 4
GHz to 40 GHz. This innovative solid polymer electrolyte which is
highly ionic conductive (10-3 S/cm at room temperature) from -40oC
to +150oC can be used in any battery application. Such polymer
exhibits properties more like a ceramic rather than polymer. The
various applied measurement methods produced accurate dielectric
results for comprehensive analysis of electrochemical properties and
ion transportation mechanism of this newly invented polymer
electrolyte. Two techniques and instruments employing air gap
measurement by Capacitance Bridge and in-waveguide measurement
by vector network analyzer are applied to measure the complex
dielectric spectra. The complex dielectric spectra are used to
determine the complex alternating current electrical conductivity and
thus the ionic conductivity.
Abstract: This study was conducted in the area of Vlora Bay,
Albania. Data about Sea Turtles Caretta caretta and Chelonia mydas,
belonging to two periods of time (1984 – 1991; 2008 – 2014) are
given. All data gathered were analyzed using recent methodologies.
For all turtles captured (as by catch), the Curve Carapace Length
(CCL) and Curved Carapace Width (CCW) were measured. These
data were statistically analyzed, where the mean was 67.11 cm for
CCL and 57.57 cm for CCW of all individuals studied (n=13). All
untagged individuals of marine turtles were tagged using metallic
tags (Stockbrand’s titanium tag) with an Albanian address. Sex was
determined and resulted that 45.4% of individuals were females,
27.3% males and 27.3% juveniles. All turtles were studied for the
presence of the epibionts. The area of Vlora Bay is used from marine
turtles (Caretta caretta) as a migratory corridor to pass from
Mediterranean to the northern part of the Adriatic Sea.
Abstract: In this study was monitored the population of the
European Pond Turtle, Emys orbicularis (Linnaeus, 1758) in the area
of Narta Lagoon, Vlora Bay (Albania), from August to October 2014.
A total of 54 individuals of E. orbicularis were studied using
different methodologies. Curved Carapace Length (CCL), Plastron
Length (PL) and Curved Carapace Width (CCW) were measured for
each individual of E. orbicularis and were statistically analyzed. All
captured turtles were separated in seven different size – classes based
on their carapace length (CCL). Each individual of E. orbicularis was
marked by notching the carapace (marginal scutes). Form all
individuals captured resulted that 37 were females (68.5%), 14 males
(25.9%), 3 juveniles (5.5%), while 18 individuals of E. orbicularis
were recaptured for the first and some for the second time.
Abstract: The well been of human beings on construction site is
very important, many man power had been lost through accidents
which kills or make workers physically unfit to carry out construction
activities, these in turn have multiple effects on the whole economy.
Thus it is necessary to put all safety items and regulations in place
before construction activities can commence. This study was carried
out in Ondo state of Nigeria to known and analyse the state of health
and safety of construction workers in the state. The study was done
using first hand observation method, 50 construction project sites
were visited in 10 major towns of Ondo state, questionnaires were
distributed and the results were analysed. The result show that
construction workers are being exposed to a lot of construction site
hazards due to lack of inadequate safety programmes and nonprovision
of appropriate safety materials for workers on site. From the
data gotten for each site visited and the statistical analysis, it can be
concluded that occurrence of accident on construction sites depends
significantly on the available safety facilities on the sites. The result of
the regression statistics show that the level of significant of the
dependence of occurrence of accident on the availability of safety
items on site is 0.0362 which is less than 0.05 maximum significant
level required. Therefore a vital way of sustaining our building
strategy is by given a detail attention to provision of adequate health
and safety items on construction sites which will reduce the
occurrence of accident, loss of man power and death of skilled
workers among others.