Abstract: Highly ordered TiO2 nanotube (TNT) arrays were
fabricated onto a pre-treated titanium foil by anodic oxidation with a
voltage of 20V in phosphoric acid/sodium fluoride electrolyte. A pretreatment
of titanium foil involved washing with acetone,
isopropanol, ethanol and deionized water. Carbon doped TiO2
nanotubes (C-TNT) was fabricated 'in-situ' with the same method in
the presence of polyvinyl alcohol and urea as carbon sources. The
affects of polyvinyl alcohol concentration and oxidation time on the
composition, morphology and structure of the C-TN were studied by
FE-SEM, EDX and XRD techniques. FESEM images of the
nanotubes showed uniform arrays of C-TNTs. The density and
microstructures of the nanotubes were greatly affected by the content
of PVA. The introduction of the polyvinyl alcohol into the electrolyte
increases the amount of C content inside TiO2 nanotube arrays
uniformly. The influence of carbon content on the photo-current of
C-TNT was investigated and the I-V profiles of the nanotubes were
established. The preliminary results indicated that the 'in-situ'
doping technique produced a superior quality nanotubes compared to
post doping techniques.
Abstract: The affect of the attendance percentage, the overall
GPA and the number of credit hours the student is enrolled in at
specific semester on the grade attained in specific course has been
studied. This study has been performed on three courses offered in
industrial engineering department at the Hashemite University in
Jordan. Study has revealed that the grade attained by a student is
strongly affected by the attendance percentage and his overall GPA
with a value of R2 of 52.5%. Another model that has been
investigated is the relation between the semester GPA and the
attendance percentage, the number of credit hours enrolled in at
specific semester, and the overall GPA. This model gave us a strong
relationship between the semester GPA and attendance percentage
and the overall GPA with a value of R2 of 76.2%.
Abstract: The Platform Screen Doors improve Indoor Air Quality
(IAQ) in the subway station; however, and the air quality is degraded
in the subway tunnel. CO2 concentration and indoor particulate matter
value are high in the tunnel. The IAQ level in subway tunnel degrades
by increasing the train movements. Air-curtain installation reduces
dusts, particles and moving toxic smokes and permits traffic by
generating virtual wall. The ventilation systems of the subway tunnel
need improvements to have better air-quality. Numerical analyses
might be effective tools analyze the flowfield inside the air-curtain
installed subway tunnel. The ANSYS CFX software is used for steady
computations of the airflow inside the tunnel. The single-track subway
tunnel has the natural shaft, the mechanical shaft, and the PSDs
installed stations. The height and width of the tunnel are 6.0 m and 4.0
m respectively. The tunnel is 400 m long and the air-curtain is installed
at the top of the tunnel. The thickness and the width of the air-curtain
are 0.08 m and 4 m respectively. The velocity of the air-curtain
changes between 20 - 30 m/s. Three cases are analyzed depending on
the installing location of the air-curtain. The discharged-air through
the natural shafts increases as the velocity of the air-curtain increases
when the air-curtain is installed between the mechanical and the
natural shafts. The pollutant-air is exhausted by the mechanical and the
natural shafts and remained air is pushed toward tunnel end. The
discharged-air through the natural shaft is low when the air-curtain
installed before the natural shaft. The mass flow rate decreases in the
tunnel after the mechanical shaft as the air-curtain velocity increases.
The computational results of the air-curtain installed tunnel become
basis for the optimum design study. The air-curtain installing location
is chosen between the mechanical and the natural shafts. The velocity
of the air-curtain is fixed as 25 m/s. The thickness and the blowing
angles of the air-curtain are the design variables for the optimum
design study. The object function of the design optimization is
maximizing the discharged air through the natural shaft.
Abstract: Cement stabilization has been widely used for
improving the strength and stiffness of soft clayey soils. Cement
treated soil specimens used to investigate the stress-strain behaviour in
the laboratory study are usually cured for 7 days. This paper examines
the effects of curing time on the strength and stress strain behaviour of
cement treated marine clay under triaxial loading condition.
Laboratory-prepared cement treated Singapore marine clay with
different mix proportion S-C-W (soil solid-cement solid-water) and
curing time (7 days to 180 days) was investigated through conducting
unconfined compressive strength test and triaxial test. The results
show that the curing time has a significant effect on the unconfined
compressive strength u q , isotropic compression behaviour and stress
strain behaviour. Although the primary yield loci of the cement treated
soil specimens with the same mix proportion expand with curing time,
they are very narrowly banded and have nearly the same shape after
being normalized by isotropic compression primary stress '
py p . The
isotropic compression primary yield stress '
py p was shown to be
linearly related to unconfined compressive strength u q for specimens
with different curing time and mix proportion. The effect of curing
time on the hardening behaviour will diminish with consolidation
stress higher than isotropic compression primary yield stress but its
damping rate is dependent on the cement content.
Abstract: The paper presents the results of the European EIE
project “Realising the potential for small scale renewable energy
sources in the home – Kyotointhehome". The project's global aim is
to inform and educate teachers, students and their families so that
they can realise the need and can assess the potential for energy
efficiency (EE) measures and renewable energy sources (RES) in
their homes. The project resources were translated and trialled by 16
partners in 10 European countries.
A web-based methodology which will enable families to assess
how RES can be incorporated into energy efficient homes was
accomplished. The web application “KYOTOINHOME" will help
the citizens to identify what they can do to help their community
meet the Kyoto target for greenhouse gas reductions and prevent
global warming. This application provides useful information on how
the citizens can use renewable energy sources in their home to
provide space heating and cooling, hot water and electricity. A
methodology for assessing heat loss in a dwelling and application of
heat pump system was elaborated and will be implemented this year.
For schools, we developed a set of practical activities concerned with
preventing climate change through using renewable energy sources.
Complementary resources will also developed in the Romanian
research project “Romania Contribution to the European Targets
Regarding the Development of Renewable Energy Sources" -
PROMES.
Abstract: This study was conducted in order to determine the physical properties and stability of mayonnaise-like emulsions as affected by modified yam starches. Native yam starch was modified via pre-gelatinization and cross-linking phosphorylation procedures. The emulsions (50% oil dispersed phase) were prepared with 0.3% native potato, native yam, pre-gelatinized yam and cross-linking phosphorylation yam starches. The droplet size of surface weighted mean diameter was found to be significantly (p < 0.05) lower in the sample with cross-linking phosphorylation yam starch as compared to other samples. Moreover, the viscosity of the sample with pregelatinized yam starch was observed to be higher than that of other samples. The phase separation stability was low in the freshly prepared and stored (45 days, 5°C) emulsions containing native yam starch. This study thus generally suggested that modified yam starches were more suitable (i.e. better physical properties and stability) to be used as stabilizers in a similar system i.e. light mayonnaises, rather than a native yam starch.
Abstract: The paper presents a novel idea to control computer
mouse cursor movement with human eyes. In this paper, a working
of the product has been described as to how it helps the special
people share their knowledge with the world. Number of traditional
techniques such as Head and Eye Movement Tracking Systems etc.
exist for cursor control by making use of image processing in which
light is the primary source. Electro-oculography (EOG) is a new
technology to sense eye signals with which the mouse cursor can be
controlled. The signals captured using sensors, are first amplified,
then noise is removed and then digitized, before being transferred to
PC for software interfacing.
Abstract: In modern era, the biggest challenge facing the
software industry is the upcoming of new technologies. So, the
software engineers are gearing up themselves to meet and manage
change in large software system. Also they find it difficult to deal
with software cognitive complexities. In the last few years many
metrics were proposed to measure the cognitive complexity of
software. This paper aims at a comprehensive survey of the metric of
software cognitive complexity. Some classic and efficient software
cognitive complexity metrics, such as Class Complexity (CC),
Weighted Class Complexity (WCC), Extended Weighted Class
Complexity (EWCC), Class Complexity due to Inheritance (CCI) and
Average Complexity of a program due to Inheritance (ACI), are
discussed and analyzed. The comparison and the relationship of these
metrics of software complexity are also presented.
Abstract: MicroRNAs (miRNAs) are small, non-coding and
regulatory RNAs about 20 to 24 nucleotides long. Their conserved
nature among the various organisms makes them a good source of
new miRNAs discovery by comparative genomics approach. The
study resulted in 21 miRNAs of 20 pre-miRNAs belonging to 16
families (miR156, 157, 158, 164, 165, 168, 169, 172, 319, 390, 393,
394, 395, 400, 472 and 861) in evergreen spruce tree (Picea). The
miRNA families; miR 157, 158, 164, 165, 168, 169, 319, 390, 393,
394, 400, 472 and 861 are reported for the first time in the Picea. All
20 miRNA precursors form stable minimum free energy stem-loop
structure as their orthologues form in Arabidopsis and the mature
miRNA reside in the stem portion of the stem loop structure. Sixteen
(16) miRNAs are from Picea glauca and five (5) belong to Picea
sitchensis. Their targets consist of transcription factors, growth
related, stressed related and hypothetical proteins.
Abstract: In this paper, Selective Adaptive Parallel Interference Cancellation (SA-PIC) technique is presented for Multicarrier Direct Sequence Code Division Multiple Access (MC DS-CDMA) scheme. The motivation of using SA-PIC is that it gives high performance and at the same time, reduces the computational complexity required to perform interference cancellation. An upper bound expression of the bit error rate (BER) for the SA-PIC under Rayleigh fading channel condition is derived. Moreover, the implementation complexities for SA-PIC and Adaptive Parallel Interference Cancellation (APIC) are discussed and compared. The performance of SA-PIC is investigated analytically and validated via computer simulations.
Abstract: Spent Sulfidic Caustic was biologically treated and
regenerated for reusing by Thiobacillus denitrificans bacteria, sulfide
content oxidized and RSNa reduced dramatically.PH in this test was
11.8 and no neutralization has been done on spent caustic, so spent
caustic as the most difficult of industrial wastes to dispose could be
regenerate and reuse instead of disposing to sea or deep wells
Abstract: Deprivation indices are widely used in public health
study. These indices are also referred as the index of inequalities or
disadvantage. Even though, there are many indices that have been
built before, it is believed to be less appropriate to use the existing
indices to be applied in other countries or areas which had different
socio-economic conditions and different geographical characteristics.
The objective of this study is to construct the index based on the
geographical and socio-economic factors in Peninsular Malaysia
which is defined as the weighted household-based deprivation index.
This study has employed the variables based on household items,
household facilities, school attendance and education level obtained
from Malaysia 2000 census report. The factor analysis is used to
extract the latent variables from indicators, or reducing the
observable variable into smaller amount of components or factor.
Based on the factor analysis, two extracted factors were selected,
known as Basic Household Amenities and Middle-Class Household
Item factor. It is observed that the district with a lower index values
are located in the less developed states like Kelantan, Terengganu
and Kedah. Meanwhile, the areas with high index values are located
in developed states such as Pulau Pinang, W.P. Kuala Lumpur and
Selangor.
Abstract: The objective of this study is to evaluate the
occurrence of fungi in aerobic and anoxic activated sludge from
membrane bioreactors (MBRs). Thirty-six samples of both aerobic
and anoxic activated sludge were taken from 2 MBR treating
domestic wastewater. Over a period of eight months 2 samples from
each plant were taken per month. The samples were prepared for
count and definition of fungi. The obtained data show that, sixty
species belonging to 27 genera were collected from activated sludge
samples under aerobic and anoxic conditions. Regarding to the fungi
definition, under aerobic condition the Geotrichum was found at
(8.8%) followed by Penicillium (75.0%), Yeasts (65.7%) and
Trichoderma (55.5%), while Yeasts (77.1%) Geotrichum
candidumand Penicillium (61.1%) species were the most prevalent in
anoxic activated sludge. The results indicate that activated sludge is
habitat for growth and sporulation of different groups of fungi, both
saprophytic and pathogenic.
Abstract: This paper is based on a study conducted in 2006 to assess the impact of computer usage on health of National Institute for Medical Research (NIMR) staff. NIMR being a research Institute, most of its staff spend substantial part of their working time on computers. There was notion among NIMR staff on possible prolonged computer usage health hazards. Hence, a study was conducted to establish facts and possible mitigation measures. A total of 144 NIMR staff were involved in the study of whom 63.2% were males and 36.8% females aged between 20 and 59 years. All staff cadres were included in the sample. The functions performed by Institute staff using computers includes; data management, proposal development and report writing, research activities, secretarial duties, accounting and administrative duties, on-line information retrieval and online communication through e-mail services. The interviewed staff had been using computers for 1-8 hours a day and for a period ranging from 1 to 20 years. The study has indicated ergonomic hazards for a significant proportion of interviewees (63%) of various kinds ranging from backache to eyesight related problems. The authors highlighted major issues which are substantially applicable in preventing occurrences of computer related problems and they urged NIMR Management and/or the government of Tanzania opts to adapt their practicability.
Abstract: Gasoline Octane Number is the standard measure of
the anti-knock properties of a motor in platforming processes, that is
one of the important unit operations for oil refineries and can be
determined with online measurement or use CFR (Cooperative Fuel
Research) engines. Online measurements of the Octane number can
be done using direct octane number analyzers, that it is too
expensive, so we have to find feasible analyzer, like ANFIS
estimators.
ANFIS is the systems that neural network incorporated in fuzzy
systems, using data automatically by learning algorithms of NNs.
ANFIS constructs an input-output mapping based both on human
knowledge and on generated input-output data pairs.
In this research, 31 industrial data sets are used (21 data for training
and the rest of the data used for generalization). Results show that,
according to this simulation, hybrid method training algorithm in
ANFIS has good agreements between industrial data and simulated
results.
Abstract: One-way functions are functions that are easy to
compute but hard to invert. Their existence is an open conjecture; it
would imply the existence of intractable problems (i.e. NP-problems
which are not in the P complexity class).
If true, the existence of one-way functions would have an impact
on the theoretical framework of physics, in particularly, quantum
mechanics. Such aspect of one-way functions has never been shown
before.
In the present work, we put forward the following.
We can calculate the microscopic state (say, the particle spin in the
z direction) of a macroscopic system (a measuring apparatus
registering the particle z-spin) by the system macroscopic state (the
apparatus output); let us call this association the function F. The
question is: can we compute the function F in the inverse direction?
In other words, can we compute the macroscopic state of the system
through its microscopic state (the preimage F -1)?
In the paper, we assume that the function F is a one-way function.
The assumption implies that at the macroscopic level the Schrödinger
equation becomes unfeasible to compute. This unfeasibility plays a
role of limit of the validity of the linear Schrödinger equation.
Abstract: The continued interest in the use of distributed generation in recent years is leading to the growth in number of distributed generators connected to distribution networks. Steady state voltage rise resulting from the connection of these generators can be a major obstacle to their connection at lower voltage levels. The present electric distribution network is designed to keep the customer voltage within tolerance limit. This may require a reduction in connectable generation capacity, under utilization of appropriate generation sites. Thus distribution network operators need a proper voltage regulation method to allow the significant integration of distributed generation systems to existing network. In this work a voltage rise problem in a typical distribution system has been studied. A method for voltage regulation of distribution system with multiple DG system by coordinated operation distributed generator, capacitor and OLTC has been developed. A sensitivity based analysis has been carried out to determine the priority for individual generators in multiple DG environment. The effectiveness of the developed method has been evaluated under various cases through simulation results.
Abstract: Standard packaging and interconnection technologies
of power devices have difficulties meeting the increasing thermal
demands of new application fields of power electronics devices.
Main restrictions are the decreasing reliability of bond-wires and
solder layers with increasing junction temperature. In the last few
years intensive efforts have been invested in developing new
packaging and interconnection solutions which may open a path to
future application of power devices. In this paper, the main failure
mechanisms of power devices are described and principle of new
packaging and interconnection concepts and their power cycling
reliability are presented.
Abstract: In this paper we present two novel 1-bit full adder
cells in dynamic logic style. NP-CMOS (Zipper) and Multi-Output
structures are used to design the adder blocks. Characteristic of
dynamic logic leads to higher speeds than the other standard static
full adder cells. Using HSpice and 0.18┬Ám CMOS technology
exhibits a significant decrease in the cell delay which can result in a
considerable reduction in the power-delay product (PDP). The PDP
of Multi-Output design at 1.8v power supply is around 0.15 femto
joule that is 5% lower than conventional dynamic full adder cell and
at least 21% lower than other static full adders.
Abstract: Fermented beverages have high expression in the
market for beverages in general, is increasingly valued in situations
where the characteristic aroma and flavor of the material that gave
rise to them are kept after processing. This study aimed to develop a
distilled beverage from passion fruit, and assess, by sensory tests and
chromatographic profile, the influence of different treatments (FM1-
spirit with pulp addiction and FM2 – spirit with bigger ratio of pulp
in must) in the setting of volatiles in the fruit drink, and performing
chemical characterization taking into account the main parameters of
quality established by the legislation. The chromatograms and the
first sensorial tests had indicated that sample FM1 possess better
characteristics of aroma, as much of how much quantitative the
qualitative point of view. However, it analyzes it sensorial end
(preference test) disclosed the biggest preference of the cloth provers
for sample FM2-2 (note 7.93), being the attributes of decisive color
and flavor in this reply, confirmed for the observed values lowest of
fixed and total acidity in the samples of treatment FM2.