Abstract: This paper presents the results of a study on the
influence of varying percentages of rock bridges along a basal surface
defining a biplanar failure mode. A pseudo-coupled-hydromechanical
brittle fracture analysis is adopted using the state-of-the-art code
Slope Model. Model results show that rock bridge failure is strongly
influenced by the incorporation of groundwater pressures. The
models show that groundwater pressure can promote total failure of a
5% rock bridge along the basal surface. Once the percentage of the
rock bridges increases to 10 and 15%, although, the rock bridges are
broken, full interconnection of the surface defining the basal surface
of the biplanar mode does not occur. Increased damage is caused
when the rock bridge is located at the daylighting end of the basal
surface in proximity to the blast damage zone. As expected, some
cracking damage is experienced in the blast damage zone, where
properties representing a good quality controlled damage blast
technique were assumed. Model results indicate the potential increase
of permeability towards the blast damage zone.
Abstract: Laura Island, which is located about 50 km away from
downtown, is a source of water supply in Majuro atoll, which is the
capital of the Republic of the Marshall Islands. Low and flat Majuro
atoll has neither river nor lake. It is very important for Majuro atoll to
ensure the conservation of its water resources. However, upconing,
which is the process of partial rising of the freshwater-saltwater
boundary near the water-supply well, was caused by the excess
pumping from it during the severe drought in 1998. Upconing will
make the water usage of the freshwater lens difficult. Thus,
appropriate water usage is required to prevent up coning in the
freshwater lens because there is no other water source during drought. Numerical simulation of water usage applying SEAWAT model
was conducted at the central part of Laura Island, including the water
supply well, which was affected by upconing. The freshwater lens was
created as a result of infiltration of consistent average rainfall. The lens
shape was almost the same as the one in 1985. 0 of monthly rainfall
and variable daily pump discharge were used to calculate the
sustainable pump discharge from the water supply well. Consequently,
the total amount of pump discharge was increased as the daily pump
discharge was increased, indicating that it needs more time to recover
from upconing. Thus, a pump standard to reduce the pump intensity is
being proposed, which is based on numerical simulation concerning
the occurrence of the up-coning phenomenon in Laura Island during
the drought.
Abstract: The end panels of a large rectangular industrial duct,
which experience significant internal pressures, also experience
considerable transverse shear due to transfer of gravity loads to the
supports. The current design practice of such thin plate panels for
shear load is based on methods used for the design of plate girder
webs. The structural arrangements, the loadings and the resulting
behavior associated with the industrial duct end panels are, however,
significantly different from those of the web of a plate girder. The
large aspect ratio of the end panels gives rise to multiple bands of
tension fields, whereas the plate girder web design is based on one
tension field. In addition to shear, the industrial end panels are
subjected to internal pressure which in turn produces significant
membrane action. This paper reports a study which was undertaken
to review the current industrial analysis and design methods and to
propose a comprehensive method of designing industrial duct end
panels for shear resistance. In this investigation, a nonlinear finite element model was
developed to simulate the behavior of industrial duct end panel, along
with the associated edge stiffeners, subjected to transverse shear and
internal pressures. The model considered the geometric imperfections
and constitutive relations for steels. Six scale independent
dimensionless parameters that govern the behavior of such end panel
were identified and were then used in a parametric study. It was
concluded that the plate slenderness dominates the shear strength of
stockier end panels, and whereas, both the plate slenderness and the
aspect ratio influence the shear strength of slender end panels. Based
on these studies, this paper proposes design aids for estimating the
shear strength of rectangular duct end panels.
Abstract: A three-dimensional numerical simulation of flow
through mini and microchannels with designed roughness is
conducted here. The effect of the roughness height (surface
roughness), geometry, Reynolds number on the friction factor, and
Nusselt number is investigated. The study is carried out by
employing CFD software, CFX. Our work focuses on a water flow
inside a circular mini-channel of 1 mm and microchannels of 500 and
100 m in diameter. The speed entry varies from 0.1 m/s to 20 m/s.
The general trend can be observed that bigger sizes of roughness
element lead to higher flow resistance. It is found that the friction
factor increases in a nonlinear fashion with the increase in obstruction
height. Particularly, the effect of roughness can no longer be ignored
at relative roughness height higher than 3%. A significant increase in
Poiseuille number is detected for all configurations considered. The
same observation can be done for Nusselt number. The transition
zone between laminar and turbulent flow depends on the channel
diameter.
Abstract: In this paper, a robust fault detection and isolation
(FDI) scheme is developed to monitor a multivariable nonlinear
chemical process called the Chylla-Haase polymerization reactor,
when it is under the cascade PI control. The scheme employs a radial
basis function neural network (RBFNN) in an independent mode to
model the process dynamics, and using the weighted sum-squared
prediction error as the residual. The Recursive Orthogonal Least
Squares algorithm (ROLS) is employed to train the model to
overcome the training difficulty of the independent mode of the
network. Then, another RBFNN is used as a fault classifier to isolate
faults from different features involved in the residual vector. Several
actuator and sensor faults are simulated in a nonlinear simulation of
the reactor in Simulink. The scheme is used to detect and isolate the
faults on-line. The simulation results show the effectiveness of the
scheme even the process is subjected to disturbances and
uncertainties including significant changes in the monomer feed rate,
fouling factor, impurity factor, ambient temperature, and
measurement noise. The simulation results are presented to illustrate
the effectiveness and robustness of the proposed method.
Abstract: A model to predict the plastic zone size for material
under plane stress condition has been developed and verified
experimentally. The developed model is a function of crack size,
crack angle and material property (dislocation density). Simulation
and validation results show that the model developed show good
agreement with experimental results. Samples of low carbon steel
(0.035%C) with included surface crack angles of 45o, 50o, 60o, 70o
and 90o and crack depths of 2mm and 4mm were subjected to low
strain rate between 0.48 x 10-3 s-1 – 2.38 x 10-3 s-1. The mechanical
properties studied were ductility, tensile strength, modulus of
elasticity, yield strength, yield strain, stress at fracture and fracture
toughness. The experimental study shows that strain rate has no
appreciable effect on the size of plastic zone while crack depth and
crack angle plays an imperative role in determining the size of the
plastic zone of mild steel materials.
Abstract: The aim of this work is to detect geometrical shape
objects in an image. In this paper, the object is considered to be as a
circle shape. The identification requires find three characteristics,
which are number, size, and location of the object. To achieve the
goal of this work, this paper presents an algorithm that combines
from some of statistical approaches and image analysis techniques.
This algorithm has been implemented to arrive at the major
objectives in this paper. The algorithm has been evaluated by using
simulated data, and yields good results, and then it has been applied
to real data.
Abstract: Wind energy is rapidly emerging as the primary
source of electricity in the Philippines, although developing an
accurate wind resource model is difficult. In this study, Weather
Research and Forecasting (WRF) Model, an open source mesoscale
Numerical Weather Prediction (NWP) model, was used to produce a
1-year atmospheric simulation with 4 km resolution on the Ilocos
Region of the Philippines. The WRF output (netCDF) extracts the
annual mean wind speed data using a Python-based Graphical User
Interface. Lastly, wind resource assessment was produced using a
GIS software. Results of the study showed that it is more flexible to
use Python scripts than using other post-processing tools in dealing
with netCDF files. Using WRF Model, Python, and Geographic
Information Systems, a reliable wind resource map is produced.
Abstract: Education and practical training crisis management
members are a topical issue nowadays. The paper deals with the
perspectives and possibilities of "smart solutions" to education for
crisis management staff. Currently, there is a large number of
simulation tools, which notes that they are suitable for practical
training of crisis management staff. The first part of the paper is focused on the introduction of the
technology simulation tools. The simulators aim is to create a
realistic environment for the practical training of extending units of
crisis staff. The second part of the paper concerns the possibilities of using the
simulation technology to the education process. The aim of this
section is to introduce the practical capabilities and potential of the
simulation programs for practical training of crisis management staff.
Abstract: In this paper, the 2-D unsteady viscous flow around
two cam shaped cylinders in tandem arrangement is numerically
simulated in order to study the characteristics of the flow in turbulent
regimes. The investigation covers the effects of high subcritical and
supercritical Reynolds numbers and L/D ratio on total drag
coefficient. The equivalent diameter of cylinders is 27.6 mm The
space between center to center of two cam shaped cylinders is define
as longitudinal pitch ratio and it varies in range of 1.5< L/D
Abstract: The Com-Poisson (CMP) model is one of the most
popular discrete generalized linear models (GLMS) that handles
both equi-, over- and under-dispersed data. In longitudinal context,
an integer-valued autoregressive (INAR(1)) process that incorporates
covariate specification has been developed to model longitudinal
CMP counts. However, the joint likelihood CMP function is
difficult to specify and thus restricts the likelihood-based estimating
methodology. The joint generalized quasi-likelihood approach
(GQL-I) was instead considered but is rather computationally
intensive and may not even estimate the regression effects due
to a complex and frequently ill-conditioned covariance structure.
This paper proposes a new GQL approach for estimating the
regression parameters (GQL-III) that is based on a single score vector
representation. The performance of GQL-III is compared with GQL-I
and separate marginal GQLs (GQL-II) through some simulation
experiments and is proved to yield equally efficient estimates as
GQL-I and is far more computationally stable.
Abstract: In the Solid-State-Drive (SSD) performance, whether
the data has been well parallelized is an important factor. SSD
parallelization is affected by allocation scheme and it is directly
connected to SSD performance. There are dynamic allocation and
static allocation in representative allocation schemes. Dynamic
allocation is more adaptive in exploiting write operation parallelism,
while static allocation is better in read operation parallelism.
Therefore, it is hard to select the appropriate allocation scheme when
the workload is mixed read and write operations. We simulated
conditions on a few mixed data patterns and analyzed the results to
help the right choice for better performance. As the results, if data
arrival interval is long enough prior operations to be finished and
continuous read intensive data environment static allocation is more
suitable. Dynamic allocation performs the best on write performance
and random data patterns.
Abstract: The application of ESS (Energy Storage Systems) in
the future grids has been the solution of the microgrid. However, high
investment costs necessitate accurate modeling and control strategy of
ESS to justify its economic viability and further underutilization.
Therefore, the reasonable control strategy for ESS which is subjected
to generator and usage helps to curtail the cost of investment and
operation costs. The rated frequency in power system is decreased
when the load is increasing unexpectedly; hence the thermal power is
operated at the capacity of only its 95% for the Governor Free (GF) to
adjust the frequency as reserve (5%) in practice. The ESS can be
utilized with governor at the same time for the frequency response due
to characteristic of its fast response speed and moreover, the cost of
ESS is declined rapidly to the reasonable price. This paper presents the
ESS control strategy to extend usage of the ESS taken account into
governor’s ramp rate and reduce the governor’s intervention as well.
All results in this paper are simulated by MATLAB.
Abstract: A theoretical study of a humidification
dehumidification solar desalination unit has been carried out to
increase understanding the effect of weather conditions on the unit
productivity. A humidification-dehumidification (HD) solar
desalination unit has been designed to provide fresh water for
population in remote arid areas. It consists of solar water collector
and air collector; to provide the hot water and air to the desalination
chamber. The desalination chamber is divided into humidification
and dehumidification towers. The circulation of air between the two
towers is maintained by the forced convection. A mathematical
model has been formulated, in which the thermodynamic relations
were used to study the flow, heat and mass transfer inside the
humidifier and dehumidifier. The present technique is performed in
order to increase the unit performance. Heat and mass balance has
been done and a set of governing equations has been solved using the
finite difference technique. The unit productivity has been calculated
along the working day during the summer and winter sessions and
has compared with the available experimental results. The average
accumulative productivity of the system in winter has been ranged
between 2.5 to 4 (kg/m2)/day, while the average summer productivity
has been found between 8 to 12 (kg/m2)/day.
Abstract: The Petri nets are the first standard for business
process modeling. Most probably, it is one of the core reasons why
all new standards created afterwards have to be so reformed as to
reach the stage of mapping the new standard onto Petri nets. The paper presents a business process repository based on a
universal database. The repository provides the possibility the data
about a given process to be stored in three different ways. Business
process repository is developed with regard to the reformation of a
given model to a Petri net in order to be easily simulated. Two different techniques for business process simulation based on
Petri nets - Yasper and Woflan are discussed. Their advantages and
drawbacks are outlined. The way of simulating business process
models, stored in the Business process repository is shown.
Abstract: Multiprocessor task scheduling problem for dependent
and independent tasks is computationally complex problem. Many
methods are proposed to achieve optimal running time. As the
multiprocessor task scheduling is NP hard in nature, therefore, many
heuristics are proposed which have improved the makespan of the
problem. But due to problem specific nature, the heuristic method
which provide best results for one problem, might not provide good
results for another problem. So, Simulated Annealing which is meta
heuristic approach is considered. It can be applied on all types of
problems. However, due to many runs, meta heuristic approach takes
large computation time. Hence, the hybrid approach is proposed by
combining the Duplication Scheduling Heuristic and Simulated
Annealing (SA) and the makespan results of Simple Simulated
Annealing and Hybrid approach are analyzed.
Abstract: Lateral Geniculate Nucleus (LGN) is the relay center
in the visual pathway as it receives most of the input information
from retinal ganglion cells (RGC) and sends to visual cortex. Low
threshold calcium currents (IT) at the membrane are the unique
indicator to characterize this firing functionality of the LGN neurons
gained by the RGC input. According to the LGN functional
requirements such as functional mapping of RGC to LGN, the
morphologies of the LGN neurons were developed. During the
neurological disorders like glaucoma, the mapping between RGC and
LGN is disconnected and hence stimulating LGN electrically using
deep brain electrodes can restore the functionalities of LGN. A
computational model was developed for simulating the LGN neurons
with three predominant morphologies each representing different
functional mapping of RGC to LGN. The firings of action potentials
at LGN neuron due to IT were characterized by varying the
stimulation parameters, morphological parameters and orientation. A
wide range of stimulation parameters (stimulus amplitude, duration
and frequency) represents the various strengths of the electrical
stimulation with different morphological parameters (soma size,
dendrites size and structure). The orientation (0-1800) of LGN
neuron with respect to the stimulating electrode represents the angle
at which the extracellular deep brain stimulation towards LGN
neuron is performed. A reduced dendrite structure was used in the
model using Bush–Sejnowski algorithm to decrease the
computational time while conserving its input resistance and total
surface area. The major finding is that an input potential of 0.4 V is
required to produce the action potential in the LGN neuron which is
placed at 100 μm distance from the electrode. From this study, it can
be concluded that the neuroprostheses under design would need to
consider the capability of inducing at least 0.4V to produce action
potentials in LGN.
Abstract: The objective of this work is to carryout critical
comparison of different actuation mechanisms like electrostatic,
thermal, piezoelectric, and magnetic with reference to a micro
cantilever. The relevant parameters like force generated,
displacement are compared in actuation methods. With these results,
helps in choosing the best actuation method for a particular
application. In this study, Comsol/Multiphysics software is used.
Modeling and simulation is done by considering the micro cantilever
of same dimensions as an actuator using all the above mentioned
actuation techniques. In addition to their small size, micro actuators
consume very little power and are capable of accurate results. In this
work, a comparison of actuation mechanisms is done to decide the
efficient system in micro domain.
Abstract: The paper discusses the problem of load transport
using farm tractors and road tractor units. This type of carriage of
goods is often done with farm vehicles. The tests were performed
with the PEMS equipment (Portable Emission Measurement System)
under actual traffic conditions. The vehicles carried a load of 20000
kg. This research method is one of the most desired because it
provides reliable information on the actual vehicle emissions and fuel
consumption (carbon balance method). For the tests, a route was
selected that simulated a trip from a small town to a food-processing
facility located in a city. The analysis of the obtained results gave a
clear answer as to what vehicles need to be used for carriage of this
type of cargo in terms of exhaust emissions and fuel consumption.
Abstract: Noninvasive diagnostics of diseases via breath
analysis has attracted considerable scientific and clinical interest for
many years and become more and more promising with the rapid
advancements in nanotechnology and biotechnology. The volatile
organic compounds (VOCs) in exhaled breath, which are mainly
blood borne, particularly provide highly valuable information about
individuals’ physiological and pathophysiological conditions.
Additionally, breath analysis is noninvasive, real-time, painless, and
agreeable to patients. We have developed a wireless sensor array
based on single-stranded DNA (ssDNA)-functionalized single-walled
carbon nanotubes (SWNT) for the detection of a number of
physiological indicators in breath. Seven DNA sequences were used
to functionalize SWNT sensors to detect trace amount of methanol,
benzene, dimethyl sulfide, hydrogen sulfide, acetone, and ethanol,
which are indicators of heavy smoking, excessive drinking, and
diseases such as lung cancer, breast cancer, and diabetes. Our test
results indicated that DNA functionalized SWNT sensors exhibit
great selectivity, sensitivity, and repeatability; and different
molecules can be distinguished through pattern recognition enabled
by this sensor array. Furthermore, the experimental sensing results
are consistent with the Molecular Dynamics simulated ssDNAmolecular
target interaction rankings. Thus, the DNA-SWNT sensor
array has great potential to be applied in chemical or biomolecular
detection for the noninvasive diagnostics of diseases and personal
health monitoring.