Abstract: Partial oxidation (POX) of light hydrocarbons (e.g.
methane) is occurred in the first part of the autothermal reformer
(ATR). The results of the detailed modeling of the reformer based on
the thermodynamic model of the POX and 1D heterogeneous
catalytic model for the fixed bed section are considered here.
According to the results, the overall performance of the ATR can be
improved by changing the important feed parameters.
Abstract: This paper presents a novel CMOS four-transistor
SRAM cell for very high density and low power embedded SRAM
applications as well as for stand-alone SRAM applications. This cell
retains its data with leakage current and positive feedback without
refresh cycle. The new cell size is 20% smaller than a conventional
six-transistor cell using same design rules. Also proposed cell uses
two word-lines and one pair bit-line. Read operation perform from
one side of cell, and write operation perform from another side of
cell, and swing voltage reduced on word-lines thus dynamic power
during read/write operation reduced. The fabrication process is fully
compatible with high-performance CMOS logic technologies,
because there is no need to integrate a poly-Si resistor or a TFT load.
HSPICE simulation in standard 0.25μm CMOS technology confirms
all results obtained from this paper.
Abstract: In order to develop forest management strategies in
tropical forest in Malaysia, surveying the forest resources and
monitoring the forest area affected by logging activities is essential.
There are tremendous effort has been done in classification of land
cover related to forest resource management in this country as it is a
priority in all aspects of forest mapping using remote sensing and
related technology such as GIS. In fact classification process is a
compulsory step in any remote sensing research. Therefore, the main
objective of this paper is to assess classification accuracy of
classified forest map on Landsat TM data from difference number of
reference data (200 and 388 reference data). This comparison was
made through observation (200 reference data), and interpretation
and observation approaches (388 reference data). Five land cover
classes namely primary forest, logged over forest, water bodies, bare
land and agricultural crop/mixed horticultural can be identified by
the differences in spectral wavelength. Result showed that an overall
accuracy from 200 reference data was 83.5 % (kappa value
0.7502459; kappa variance 0.002871), which was considered
acceptable or good for optical data. However, when 200 reference
data was increased to 388 in the confusion matrix, the accuracy
slightly improved from 83.5% to 89.17%, with Kappa statistic
increased from 0.7502459 to 0.8026135, respectively. The accuracy
in this classification suggested that this strategy for the selection of
training area, interpretation approaches and number of reference data
used were importance to perform better classification result.
Abstract: This paper applies an anthropological approach to illuminate the dynamic cultural geography of Kazakhstani Korean ethnicity focusing on its turning point, the historic “Seoul Olympic Games in 1988." The Korean ethnic group was easily considered as a harmonious and homogeneous community by outsiders, but there existed deep-seated conflicts and hostilities within the ethnic group. The majority-s oppositional dichotomy of superiority and inferiority toward the minority was continuously reorganized and reinforced by difference in experience, memory and sentiment. However, such a chronic exclusive boundary was collapsed following the patriotism ignited by the Olympics held in their mother country. This paper explores the fluidity of subject by formation of the boundary in which constructed cultural differences are continuously essentialized and reproduced, and by dissolution of cultural barrier in certain contexts.
Abstract: The paper deals with the perspectives and possibilities
of "smart solutions" to critical infrastructure protection. It means that
common computer aided technologies are used from the perspective
of new, better protection of selected infrastructure objects. The paper
is focused on the co-product of the Czech Defence Research Project -
ADAPTIV. This project is carrying out by the University of Defence,
Faculty of Economics and Management at the Department of Civil
Protection. The project creates system and technology for adaptive
cybernetic camouflage of armed forces objects, armaments, vehicles
and troops and of mobilization infrastructure. These adaptive
camouflage system and technology will be useful for army tactic
activities protection and for decoys generation also. The fourth
chapter of the paper concerns the possibilities of using the introduced
technology to the protection of selected civil (economically
important), critical infrastructure objects. The aim of this section
is to introduce the scientific capabilities and potential of the
University of Defence research results and solutions for the practice.
Abstract: In this paper we improve the quasilinearization method by barycentric Lagrange interpolation because of its numerical stability and computation speed to achieve a stable semi analytical solution. Then we applied the improved method for solving the Fin problem which is a nonlinear equation that occurs in the heat transferring. In the quasilinearization approach the nonlinear differential equation is treated by approximating the nonlinear terms by a sequence of linear expressions. The modified QLM is iterative but not perturbative and gives stable semi analytical solutions to nonlinear problems without depending on the existence of a smallness parameter. Comparison with some numerical solutions shows that the present solution is applicable.
Abstract: In this paper we describe a hybrid technique of Minimax search and aggregate Mahalanobis distance function synthesis to evolve Awale game player. The hybrid technique helps to suggest a move in a short amount of time without looking into endgame database. However, the effectiveness of the technique is heavily dependent on the training dataset of the Awale strategies utilized. The evolved player was tested against Awale shareware program and the result is appealing.
Abstract: A challenging problem in radar signal processing is to
achieve reliable target detection in the presence of interferences. In
this paper, we propose a novel algorithm for automatic censoring of
radar interfering targets in log-normal clutter. The proposed
algorithm, termed the forward automatic censored cell averaging
detector (F-ACCAD), consists of two steps: removing the corrupted
reference cells (censoring) and the actual detection. Both steps are
performed dynamically by using a suitable set of ranked cells to
estimate the unknown background level and set the adaptive
thresholds accordingly. The F-ACCAD algorithm does not require
any prior information about the clutter parameters nor does it require
the number of interfering targets. The effectiveness of the F-ACCAD
algorithm is assessed by computing, using Monte Carlo simulations,
the probability of censoring and the probability of detection in
different background environments.
Abstract: Consumer electronics are pervasive. It is impossible to
imagine a household or office without DVD players, digital cameras,
printers, mobile phones, shavers, electrical toothbrushes, etc. All
these devices operate at different voltage levels ranging from 1.8 to
20 VDC, in the absence of universal standards. The voltages
available are however usually 120/230 VAC at 50/60 Hz. This
situation makes an individual electrical energy conversion system
necessary for each device. Such converters usually involve several
conversion stages and often operate with excessive losses and poor
reliability. The aim of the project presented in this paper is to design
and implement a multi-channel DC/DC converter system,
customizing the output voltage and current ratings according to the
requirements of the load. Distributed, multi-agent techniques will be
applied for the control of the DC/DC converters.
Abstract: This paper features the mathematical modeling of a single input single output based Timoshenko smart beam. Further, this mathematical model is used to design a multirate output feedback based discrete sliding mode controller using Bartoszewicz law to suppress the flexural vibrations. The first 2 dominant vibratory modes is retained. Here, an application of the discrete sliding mode control in smart systems is presented. The algorithm uses a fast output sampling based sliding mode control strategy that would avoid the use of switching in the control input and hence avoids chattering. This method does not need the measurement of the system states for feedback as it makes use of only the output samples for designing the controller. Thus, this methodology is more practical and easy to implement.
Abstract: Rarefied gas flows are often occurred in micro electro
mechanical systems and classical CFD could not precisely anticipate
the flow and thermal behavior due to the high Knudsen number.
Therefore, the heat transfer and the fluid dynamics characteristics of
rarefied gas flows in both a two-dimensional simple microchannel
and geometry similar to single Knudsen compressor have been
investigated with a goal of increasing performance of a actual
Knudsen compressor by using a particle simulation method. Thermal
transpiration and thermal creep, which are rarefied gas dynamic
phenomena, that cause movement of the flow from less to higher
temperature is generated by using two different longitude temperature
gradients (Linear, Step) along the walls of the flow microchannel. In
this study the influence of amount of temperature gradient and
governing pressure in various Knudsen numbers and length-to-height
ratios have been examined.
Abstract: This paper deals with the modeling and the evaluation of a multiplicative phase noise influence on the bit error ratio in a general space communication system. Our research is focused on systems with multi-state phase shift keying modulation techniques and it turns out, that the phase noise significantly affects the bit error rate, especially for higher signal to noise ratios. These results come from a system model created in Matlab environment and are shown in a form of constellation diagrams and bit error rate dependencies. The change of a user data bit rate is also considered and included into simulation results. Obtained outcomes confirm theoretical presumptions.
Abstract: While compressing text files is useful, compressing
still image files is almost a necessity. A typical image takes up much
more storage than a typical text message and without compression
images would be extremely clumsy to store and distribute. The
amount of information required to store pictures on modern
computers is quite large in relation to the amount of bandwidth
commonly available to transmit them over the Internet and
applications. Image compression addresses the problem of reducing
the amount of data required to represent a digital image. Performance
of any image compression method can be evaluated by measuring the
root-mean-square-error & peak signal to noise ratio. The method of
image compression that will be analyzed in this paper is based on the
lossy JPEG image compression technique, the most popular
compression technique for color images. JPEG compression is able to
greatly reduce file size with minimal image degradation by throwing
away the least “important" information. In JPEG, both color
components are downsampled simultaneously, but in this paper we
will compare the results when the compression is done by
downsampling the single chroma part. In this paper we will
demonstrate more compression ratio is achieved when the
chrominance blue is downsampled as compared to downsampling the
chrominance red in JPEG compression. But the peak signal to noise
ratio is more when the chrominance red is downsampled as compared
to downsampling the chrominance blue in JPEG compression. In
particular we will use the hats.jpg as a demonstration of JPEG
compression using low pass filter and demonstrate that the image is
compressed with barely any visual differences with both methods.
Abstract: The utilization of cheese whey as a fermentation
substrate to produce bio-ethanol is an effort to supply bio-ethanol
demand as a renewable energy. Like other process systems, modeling
is also required for fermentation process design, optimization and
plant operation. This research aims to study the fermentation process
of cheese whey by applying mathematics and fundamental concept in
chemical engineering, and to investigate the characteristic of the
cheese whey fermentation process. Steady state simulation results for
inlet substrate concentration of 50, 100 and 150 g/l, and various
values of hydraulic retention time, showed that the ethanol
productivity maximum values were 0.1091, 0.3163 and 0.5639 g/l.h
respectively. Those values were achieved at hydraulic retention time
of 20 hours, which was the minimum value used in this modeling.
This showed that operating reactor at low hydraulic retention time
was favorable. Model of bio-ethanol production from cheese whey
will enhance the understanding of what really happen in the
fermentation process.
Abstract: This paper presents a real-time defect detection
algorithm for high-speed steel bar in coil. Because the target speed is
very high, proposed algorithm should process quickly the large
volumes of image for real-time processing. Therefore, defect detection
algorithm should satisfy two conflicting requirements of reducing the
processing time and improving the efficiency of defect detection. To
enhance performance of detection, edge preserving method is
suggested for noise reduction of target image. Finally, experiment
results show that the proposed algorithm guarantees the condition of
the real-time processing and accuracy of detection.
Abstract: Turkey has 72 % of total world boron reserves on the
basis of B2O3.Borates that is a refined form of boron minerals have a
wide range of applications. Zinc borates can be used as multifunctional
synergistic additives. The most important properties are
low solubility in water and high dehydration temperature. Zinc
borates dehydrate above 290°C and anhydrous zinc borate has
thermal resistance about 400°C. Zinc borates can be synthesized
using several methods such as hydrothermal and solid-state
processes. In this study, the solid-state method was applied between
500 and 800°C using the starting materials of ZnO and H3BO3 with
1:4 mole ratio. The reaction time was determined as 4 hours after
some preliminary experiments. After the synthesis, the crystal
structure and the morphology of the products were examined by XRay
Diffraction (XRD), Fourier Transform Infrared Spectroscopy
(FT-IR) and Raman Spectrometer. As a result the form of ZnB4O7
was synthesized with the highest crystal score at 800°C.
Abstract: The sustainability of a place depends on a series of factors which contribute to the quality of life, sense of place and recognition of identity. An activity like walking, which in itself is obviously ''sustainable'', can become non sustainable if the context in which it is carried out does not meet the conditions for an adequate quality of life. This work is aimed at proposing the analytical method of Place Maker to identify the elements that do not feature in traditional mapping and which constitute the contemporary identity of the places, and the relative complex map to represent those elements and support sustainable urban identity design. The method's potential for areas with a predominantly pedestrian vocation is illustrated by means of the case study of the Ramblas in Barcelona.
Abstract: The purpose of this study was to study postpartum breastfeeding mothers to determine the impact their psychosocial and spiritual dimensions play in promoting full-term (6 month duration) breastfeeding of their infants. Purposive and snowball sampling methods were used to identify and recruit the study's participants. A total of 23 postpartum mothers, who were breastfeeding within 6 weeks after giving birth, participated in this study. In-depth interviews combined with observations, participant focus groups, and ethnographic records were used for data collection. The Data were then analyzed using content analysis and typology. The results of this study illustrated that postpartum mothers experienced fear and worry that they would lack support from their spouse, family and peers, and that their infant would not get enough milk It was found that the main barrier mothers faced in breastfeeding to full-term was the difficulty of continuing to breastfeed when returning to work. 81.82% of the primiparous mothers and 91.67% of the non-primiparous mothers were able to breastfeed for the desired full-term of 6 months. Factors found to be related to breastfeeding for six months included 1) belief and faith in breastfeeding, 2) support from spouse and family members, 3) counseling from public health nurses and friends. The sample also provided evidence that religious principles such as tolerance, effort, love, and compassion to their infant, and positive thinking, were used in solving their physical, mental and spiritual problems.
Abstract: The dynamic behaviour of a four-bar linkage driven by a velocity controlled DC motor is discussed in the paper. In particular the author presents the results obtained by means of a specifically developed software, which implements the mathematical models of all components of the system (linkage, transmission, electric motor, control devices). The use of this software enables a more efficient design approach, since it allows the designer to check, in a simple and immediate way, the dynamic behaviour of the mechanism, arising from different values of the system parameters.
Abstract: In this work, ionic liquids (ILs) for CO2 capturing in typical absorption/stripper process are considered. The use of ionic liquids is considered to be cost-effective because it requires less energy for solvent recovery compared to other conventional processes. A mathematical model is developed for the process based on Peng-Robinson (PR) equation of state (EoS) which is validated with experimental data for various solutions involving CO2. The model is utilized to study the sorbent and energy demand for three types of ILs at specific CO2 capturing rates. The energy demand is manifested by the vapor-liquid equilibrium temperature necessary to remove the captured CO2 from the used solvent in the regeneration step. It is found that higher recovery temperature is required for solvents with higher solubility coefficient. For all ILs, the temperature requirement is less than that required by the typical monoethanolamine (MEA) solvent. The effect of the CO2 loading in the sorbent stream on the process performance is also examined.