Abstract: The load frequency control problem of power systems has attracted a lot of attention from engineers and researchers over the years. Increasing and quickly changing load demand, coupled with the inclusion of more generators with high variability (solar and wind power generators) on the network are making power systems more difficult to regulate. Frequency changes are unavoidable but regulatory authorities require that these changes remain within a certain bound. Engineers are required to perform the tricky task of adjusting the control system to maintain the frequency within tolerated bounds. It is well known that to minimize frequency variations, a large proportional feedback gain (speed regulation constant) is desirable. However, this improvement in performance using proportional feedback comes about at the expense of a reduced stability margin and also allows some steady-state error. A conventional PI controller is then included as a secondary control loop to drive the steadystate error to zero. In this paper, we propose a robust controller to replace the conventional PI controller which guarantees performance and stability of the power system over the range of variation of the speed regulation constant. Simulation results are shown to validate the superiority of the proposed approach on a simple single-area power system model.
Abstract: In this paper we propose a novel RF LDMOS structure which employs a thin strained silicon layer at the top of the channel and the N-Drift region. The strain is induced by a relaxed Si0.8 Ge0.2 layer which is on top of a compositionally graded SiGe buffer. We explain the underlying physics of the device and compare the proposed device with a conventional LDMOS in terms of energy band diagram and carrier concentration. Numerical simulations of the proposed strained silicon laterally diffused MOS using a 2 dimensional device simulator indicate improvements in saturation and linear transconductance, current drivability, cut off frequency and on resistance. These improvements are however accompanied with a suppression in the break down voltage.
Abstract: Using of natural lighting has come into prominence in
constructed buildings, especially in last ten years, under scope of
energy efficiency. Natural lighting methods are one of the methods
that aim to take advantage of day light in maximum level and
decrease using of artificial lighting. Increasing of day light amount in
buildings by using suitable methods will give optimum result in
terms of comfort and energy saving when the daylight-artificial light
integration is ensured with a suitable control system. Using of natural
light in places that require lighting will ensure energy saving in great
extent. With this study, it is aimed to save energy used for purpose of
lighting. Under this scope, lighting of a scanning laboratory of a
hospital was realized by using a lighting automation containing
natural and artificial lighting. In natural lighting, light pipes were
used and in artificial lighting, dimmable power LED modules were
used. Necessity of lighting was followed with motion sensors. The
lighting automation containing natural and artificial light was ensured
with fuzzy logic control. At the scanning laboratory where this
application was realized, energy saving in lighting was obtained.
Abstract: The objectives of this research are to search the
management pattern of Bang Khonthi lodging entrepreneurs for
sufficient economy ways, to know the threat that affects this sector
and design fit arrangement model to sustain their business with
Samut Songkram style. What will happen if they do not use this
approach? Will they have a financial crisis? The data and information
are collected by informal discussions with 8 managers and 400
questionnaires. A mixed methods of both qualitative research and
quantitative research are used. Bent Flyvbjerg-s phronesis is utilized
for this analysis. Our research will prove that sufficient economy can
help small business firms to solve their problems. We think that the
results of our research will be a financial model to solve many
problems of the entrepreneurs and this way will can be a model for
other provinces of Thailand.
Abstract: The use of additions in cement in manufacturing,
mortar and concrete offers economic and ecological advantages. Cements with additions such as limestone, slag and natural
pouzzolana are produced in cement factories in Algeria. Several studies analyzed the effect of these additions on the physical and
mechanical properties as well as the durability of concrete. However,
few studies were conducted on the effect of local metakaolin on
mechanical properties and durability of concrete. The main purpose
of this paper is to analyze the performance of mortar and concrete with local metakaolin. The preparation of the metakaolin was carried
out by calcination of kaolin at a temperature of 850 °C for a period of 3 hours. The experimental results have shown that the rates of
substitutions of 10 and 15% metakaolin increases the compressive
strength and flexural strength at both early age and long term. The durability and the permeability were also improved by reducing the
coefficient of sorptivity.
Abstract: Buildings are considered as significant part in the
cities, which plays main role in organization and arrangement of city
appearance, which is affects image of that building facades, as an
connective between inner and outer space, have a main role in city
image and they are classified as rich image and poor image by people
evaluation which related to visual architectural and urban elements in
building facades. the buildings in Karimi street , in Lahijan city
where, lies in north of Iran, contain the variety of building's facade
types which, have made a city image in Historical part of Lahijan
city, while reflected the Iranian cities identity. The study attempt to
identify the architectural and urban elements that impression the
image of building facades in historical area, based on public
evaluation. Quantitative method were used and the data was collected
through questionnaire survey, the result presented architectural style,
color, shape, and design evaluated by people as most important factor
which should be understate in future development. in fact, the rich
architectural style with strong design make strong city image as weak
design make poor city image.
Abstract: This work presents the mixed-mode II/III prestressed split-cantilever beam specimen for the fracture testing of composite materials. In accordance with the concept of prestressed composite beams one of the two fracture modes is provided by the prestressed state of the specimen, and the other one is increased up to fracture initiation by using a testing machine. The novel beam-like specimen is able to provide any combination of the mode-II and mode-III energy release rates. A simple closed-form solution is developed using beam theory as a data reduction scheme and for the calculation of the energy release rates in the new configuration. The applicability and the limitations of the novel fracture mechanical test are demonstrated using unidirectional glass/polyester composite specimens. If only crack propagation onset is involved then the mixed-mode beam specimen can be used to obtain the fracture criterion of transparent composite materials in the GII - GIII plane in a relatively simple way.
Abstract: The study applied a combination of organisational learning models (Senge, 1994: Pedler, Burgoyne and Boydell, 1991) and later adopted fifteen organisational learning principles with one of the biggest energy providers in South East Asia. The purposes of the current study were to: a) investigate the company-s practices on fifteen organisational learning principles; b) explore the perceptions and expectations of its employees in relations to the principles; and c) compare the perceptions and expectations between management and non-management staff toward the fifteen factors. One hundred and ten employees responded on a designed questionnaire and the results indicated that the company was practicing activities that associated with organisational learning principles. Also, according to the T-test results, significant differences between management and non-management respondents were found. Research implications are also provided.
Abstract: Human computer interaction has progressed
considerably from the traditional modes of interaction. Vision based
interfaces are a revolutionary technology, allowing interaction
through human actions, gestures. Researchers have developed
numerous accurate techniques, however, with an exception to few
these techniques are not evaluated using standard HCI techniques. In
this paper we present a comprehensive framework to address this
issue. Our evaluation of a computer vision application shows that in
addition to the accuracy, it is vital to address human factors
Abstract: Employees commitments of vision and mission of
organization is effected due to manager’s executes by approach of
leadership The leaders who have attributions like vision, confidence
and correctitude, sharing and participation, creativeness, progressive
learning –improvement and responsibility are effective to increase
organizational commitment if they are sensitive to expectation and
requirement of employees in an organization. Studies about
organizational commitment appear results that employees who have
strong organizational commitment have the most contribution. In this
study, “Leadership” and “Organizational Commitment” conduct
surveys to 31 employees of Ahmet Özdemir Nak. Tic. San. A.Ş.
which has operations in road and railway transportation sector. It is
analyzed the effects of leadership approach to organizational
commitment deals with result of survey.
Abstract: In this paper the Laplace Decomposition method is developed to solve linear and nonlinear fractional integro- differential equations of Volterra type.The fractional derivative is described in the Caputo sense.The Laplace decomposition method is found to be fast and accurate.Illustrative examples are included to demonstrate the validity and applicability of presented technique and comparasion is made with exacting results.
Abstract: This article presents the results of researchrelated to the assessment protocol weightedcumulative expected transmission time (WCETT)applied to cognitive radio networks.The development work was based on researchdone by different authors, we simulated a network,which communicates wirelessly, using a licensedchannel, through which other nodes are notlicensed, try to transmit during a given time nodeuntil the station's owner begins its transmission.
Abstract: This is the second part of the paper. It, aside from the
core subroutine test reported previously, focuses on the simulation of
turbulence governed by the full STF Navier-Stokes equations on a
large scale. Law of the wall is found plausible in this study as a model
of the boundary layer dynamics. Model validations proceed to
include velocity profiles of a stationary turbulent Couette flow, pure
sloshing flow simulations, and the identification of water-surface
inclination due to fluid accelerations. Errors resulting from the
irrotational and hydrostatic assumptions are explored when studying
a wind-driven water circulation with no shakings. Illustrative
examples show that this numerical strategy works for the simulation
of sloshing-shear mixed flow in a 3-D rigid rectangular base tank.
Abstract: The article presents findings from the study and
analysis of the results of an experimental programme focused on the
production of concrete and fibre reinforced concrete in which natural
aggregate has been substituted with brick or concrete recyclate. The
research results are analyzed to monitor the effect of mechanicalphysical
characteristics on the durability properties of tested
cementitious composites. The key parts of the fibre reinforced
concrete mix are the basic components: aggregates – recyclate,
cement, fly ash, water and fibres. Their specific ratios and the
properties of individual components principally affect the resulting
behaviour of fresh fibre reinforced concrete and the characteristics of
the final product. The article builds on the sources dealing with the
use of recycled aggregates from construction and demolition waste in
the production of fibre reinforced concrete. The implemented
procedure of testing the composite contributes to the building
sustainability in environmental engineering.
Abstract: Qualification of doctoral students- and the candidates for a scientific degree is evaluated by the ability to solve scientific ideas in an innovative way, consequently, being a potential of research and science they play a significant role in the sustainability context of the society. The article deals with the analysis of the results of the pilot project, the aim of which has been to study the structure of doctoral students- research competences in the sustainability context. With the existance of variety of theories on research competence development, their analysis focuses on the attained aim approach. Three competence groups have been identified in this study: informative, communicative and instrumental. Within the study the doctoral students and candidates for a scientific degree (N=64) made their self-assessment of research competences. The study results depict their present research competence development level and its dynamics according to the aim to attain.
Abstract: Multiple sequence alignment is a fundamental part in
many bioinformatics applications such as phylogenetic analysis.
Many alignment methods have been proposed. Each method gives a
different result for the same data set, and consequently generates a
different phylogenetic tree. Hence, the chosen alignment method
affects the resulting tree. However in the literature, there is no
evaluation of multiple alignment methods based on the comparison of
their phylogenetic trees. This work evaluates the following eight
aligners: ClustalX, T-Coffee, SAGA, MUSCLE, MAFFT, DIALIGN,
ProbCons and Align-m, based on their phylogenetic trees (test trees)
produced on a given data set. The Neighbor-Joining method is used
to estimate trees. Three criteria, namely, the dNNI, the dRF and the
Id_Tree are established to test the ability of different alignment
methods to produce closer test tree compared to the reference one
(true tree). Results show that the method which produces the most
accurate alignment gives the nearest test tree to the reference tree.
MUSCLE outperforms all aligners with respect to the three criteria
and for all datasets, performing particularly better when sequence
identities are within 10-20%. It is followed by T-Coffee at lower
sequence identity (30%), trees scores of all methods
become similar.
Abstract: Magnesium alloys have gained increased attention in recent years in automotive, electronics, and medical industry. This because of magnesium alloys have better properties than aluminum alloys and steels in respects of their low density and high strength to weight ratio. However, the main problems of magnesium alloy welding are the crack formation and the appearance of porosity during the solidification. This paper proposes a unique technique to weld two thin sheets of AZ31B magnesium alloy using a paste containing Ag nanoparticles. The paste containing Ag nanoparticles of 5 nm in average diameter and an organic solvent was used to coat the surface of AZ31B thin sheet. The coated sheet was heated at 100 °C for 60 s to evaporate the solvent. The dried sheet was set as a lower AZ31B sheet on the jig, and then lap fillet welding was carried out by using a pulsed Nd:YAG laser in a closed box filled with argon gas. The characteristics of the microstructure and the corrosion behavior of the joints were analyzed by opticalmicroscopy (OM), energy dispersive spectrometry (EDS), electron probe micro-analyzer (EPMA), scanning electron microscopy (SEM), and immersion corrosion test. The experimental results show that the wrought AZ31B magnesium alloy can be joined successfully using Ag nanoparticles. Ag nanoparticles insert promote grain refinement, narrower the HAZ width and wider bond width compared to weld without and insert. Corrosion rate of welded AZ31B with Ag nanoparticles reduced up to 44 % compared to base metal. The improvement of corrosion resistance of welded AZ31B with Ag nanoparticles due to finer grains and large grain boundaries area which consist of high Al content. β-phase Mg17Al12 could serve as effective barrier and suppressed further propagation of corrosion. Furthermore, Ag distribution in fusion zone provide much more finer grains and may stabilize the magnesium solid solution making it less soluble or less anodic in aqueous
Abstract: Currently, slider process of Hard Disk Drive Industry
become more complex, defective diagnosis for yield improvement
becomes more complicated and time-consumed. Manufacturing data
analysis with data mining approach is widely used for solving that
problem. The existing mining approach from combining of the KMean
clustering, the machine oriented Kruskal-Wallis test and the
multivariate chart were applied for defective diagnosis but it is still
be a semiautomatic diagnosis system. This article aims to modify an
algorithm to support an automatic decision for the existing approach.
Based on the research framework, the new approach can do an
automatic diagnosis and help engineer to find out the defective
factors faster than the existing approach about 50%.
Abstract: Reactiondiffusion systems are mathematical models that describe how the concentration of one or more substances distributed in space changes under the influence of local chemical reactions in which the substances are converted into each other, and diffusion which causes the substances to spread out in space. The classical representation of a reaction-diffusion system is given by semi-linear parabolic partial differential equations, whose general form is ÔêétX(x, t) = DΔX(x, t), where X(x, t) is the state vector, D is the matrix of the diffusion coefficients and Δ is the Laplace operator. If the solute move in an homogeneous system in thermal equilibrium, the diffusion coefficients are constants that do not depend on the local concentration of solvent and of solutes and on local temperature of the medium. In this paper a new stochastic reaction-diffusion model in which the diffusion coefficients are function of the local concentration, viscosity and frictional forces of solvent and solute is presented. Such a model provides a more realistic description of the molecular kinetics in non-homogenoeus and highly structured media as the intra- and inter-cellular spaces. The movement of a molecule A from a region i to a region j of the space is described as a first order reaction Ai k- → Aj , where the rate constant k depends on the diffusion coefficient. Representing the diffusional motion as a chemical reaction allows to assimilate a reaction-diffusion system to a pure reaction system and to simulate it with Gillespie-inspired stochastic simulation algorithms. The stochastic time evolution of the system is given by the occurrence of diffusion events and chemical reaction events. At each time step an event (reaction or diffusion) is selected from a probability distribution of waiting times determined by the specific speed of reaction and diffusion events. Redi is the software tool, developed to implement the model of reaction-diffusion kinetics and dynamics. It is a free software, that can be downloaded from http://www.cosbi.eu. To demonstrate the validity of the new reaction-diffusion model, the simulation results of the chaperone-assisted protein folding in cytoplasm obtained with Redi are reported. This case study is redrawing the attention of the scientific community due to current interests on protein aggregation as a potential cause for neurodegenerative diseases.
Abstract: As the disfunctions of the information society and
social development progress, intrusion problems such as malicious
replies, spam mail, private information leakage, phishing, and
pharming, and side effects such as the spread of unwholesome
information and privacy invasion are becoming serious social
problems. Illegal access to information is also becoming a problem as
the exchange and sharing of information increases on the basis of the
extension of the communication network. On the other hand, as the
communication network has been constructed as an international,
global system, the legal response against invasion and cyber-attack
from abroad is facing its limit. In addition, in an environment where
the important infrastructures are managed and controlled on the basis
of the information communication network, such problems pose a
threat to national security. Countermeasures to such threats are
developed and implemented on a yearly basis to protect the major
infrastructures of information communication. As a part of such
measures, we have developed a methodology for assessing the
information protection level which can be used to establish the
quantitative object setting method required for the improvement of the
information protection level.