Abstract: During recent years wind turbine technology has
undergone rapid developments. Growth in size and the optimization
of wind turbines has enabled wind energy to become increasingly
competitive with conventional energy sources. As a result today-s
wind turbines participate actively in the power production of several
countries around the world. These developments raise a number of
challenges to be dealt with now and in the future. The penetration of
wind energy in the grid raises questions about the compatibility of the
wind turbine power production with the grid. In particular, the
contribution to grid stability, power quality and behavior during fault
situations plays therefore as important a role as the reliability. In the
present work, we addressed two fault situations that have shown their
influence on the generator and the behavior of the wind over the
defects which are briefly discussed based on simulation results.
Abstract: The Portuguese Constitution, in article 22, instituted
the general principle of tort liability of the State and other public law
entities.
Consequently, ordinary legislation established the tort liability of
the State into the Portuguese Legal Order, by means of Decree-Law
48051, of 1967.
This decree, which was criticised extensively, was amended by
virtue of Law 67/2007, of 31st December, establishing the regime for
tort liability arising from losses caused by third parties, due to the
acts of public management in relation to all the functions of the State,
i.e. i) administrative, ii) legislative, and iii) jurisdictional.
Abstract: In this study, the contact problem of a layered composite which consists of two materials with different elastic constants and heights resting on two rigid flat supports with sharp edges is considered. The effect of gravity is neglected. While friction between the layers is taken into account, it is assumed that there is no friction between the supports and the layered composite so that only compressive tractions can be transmitted across the interface. The layered composite is subjected to a uniform clamping pressure over a finite portion of its top surface. The problem is reduced to a singular integral equation in which the contact pressure is the unknown function. The singular integral equation is evaluated numerically and the results for various dimensionless quantities are presented in graphical forms.
Abstract: In this paper, all-optical signal processors that perform
both microwave mixing and bandpass filtering in a radio-over-fiber
(RoF) link are presented. The key device is a Mach-Zehnder
modulator (MZM) which performs all-optical microwave mixing. An
up-converted microwave signal is obtained and other unwanted
frequency components are suppressed at the end of the fiber span.
Abstract: Video Mosaicing is the stitching of selected frames of
a video by estimating the camera motion between the frames and
thereby registering successive frames of the video to arrive at the
mosaic. Different techniques have been proposed in the literature for
video mosaicing. Despite of the large number of papers dealing with
techniques to generate mosaic, only a few authors have investigated
conditions under which these techniques generate good estimate of
motion parameters. In this paper, these techniques are studied under
different videos, and the reasons for failures are found. We propose
algorithms with incorporation of outlier removal algorithms for better
estimation of motion parameters.
Abstract: In this paper we examine the use of global texture analysis based approaches for the purpose of Persian font recognition in machine-printed document images. Most existing methods for font recognition make use of local typographical features and connected component analysis. However derivation of such features is not an easy task. Gabor filters are appropriate tools for texture analysis and are motivated by human visual system. Here we consider document images as textures and use Gabor filter responses for identifying the fonts. The method is content independent and involves no local feature analysis. Two different classifiers Weighted Euclidean Distance and SVM are used for the purpose of classification. Experiments on seven different type faces and four font styles show average accuracy of 85% with WED and 82% with SVM classifier over typefaces
Abstract: The paper describes the evaluation of quality of
control for cases of controlled non-minimal phase plants. Control
circuits containing non-minimal phase plants have different
properties, they manifest reversed reaction at the beginning of unit
step response. For these types of plants are developed special
criterion of quality of control, which considers the difference and can
be helpful for synthesis of optimal controller tuning. All results are
clearly presented using Matlab/Simulink models.
Abstract: Positron emission particle tracking (PEPT) is a
technique in which a single radioactive tracer particle can be
accurately tracked as it moves. A limitation of PET is that in order to
reconstruct a tomographic image it is necessary to acquire a large
volume of data (millions of events), so it is difficult to study rapidly
changing systems. By considering this fact, PEPT is a very fast
process compared with PET.
In PEPT detecting both photons defines a line and the annihilation
is assumed to have occurred somewhere along this line. The location
of the tracer can be determined to within a few mm from coincident
detection of a small number of pairs of back-to-back gamma rays and
using triangulation. This can be achieved many times per second and
the track of a moving particle can be reliably followed. This
technique was invented at the University of Birmingham [1].
The attempt in PEPT is not to form an image of the tracer particle
but simply to determine its location with time. If this tracer is
followed for a long enough period within a closed, circulating system
it explores all possible types of motion.
The application of PEPT to industrial process systems carried out
at the University of Birmingham is categorized in two subjects: the
behaviour of granular materials and viscous fluids. Granular
materials are processed in industry for example in the manufacture of
pharmaceuticals, ceramics, food, polymers and PEPT has been used
in a number of ways to study the behaviour of these systems [2].
PEPT allows the possibility of tracking a single particle within the
bed [3]. Also PEPT has been used for studying systems such as: fluid
flow, viscous fluids in mixers [4], using a neutrally-buoyant tracer
particle [5].
Abstract: Social, culture and artistic status of a society in
various historical eras is affected by numerous, and sometimes
imposed, factors that better understanding requires analysis of such
conditions. Throughout history Iran has been involved with
determining and significant events that examining each of these
events can improve the understanding of social conditions of this
country in the intended time. Mongolian conquest of Iran is one of
most significant events in the history of Iran with consequences that
never left Iranian societies. During this tragic invasion and
subsequent devastating wars, which led to establishment of Ilkhanate
dynasty, numerous cultural and artistic changes occurred both in
Mongolian conquerors and Iranian society. This study examines these
changes with a glimpse towards art and architecture as important part
of cultural aspects and social communication.
Abstract: In a bi-fuel diesel engine, the carburetor plays a vital
role in switching from fuel gas to petrol mode operation and viceversa.
The carburetor is the most important part of the fuel system of
a diesel engine. All diesel engines carry variable venturi mixer
carburetors. The basic operation of the carburetor mainly depends on
the restriction barrel called the venturi. When air flows through the
venturi, its speed increases and its pressure decreases. The main
challenge focuses on designing a mixing device which mixes the
supplied gas is the incoming air at an optimum ratio. In order to
surmount the identified problems, the way fuel gas and air flow in
the mixer have to be analyzed. In this case, the Computational Fluid
Dynamics or CFD approach is applied in design of the prototype
mixer. The present work is aimed at further understanding of the air
and fuel flow structure by performing CFD studies using a software
code. In this study for mixing air and gas in the condition that has
been mentioned in continuance, some mixers have been designed.
Then using of computational fluid dynamics, the optimum mixer has
been selected. The results indicated that mixer with 12 holes can
produce a homogenous mixture than those of 8-holes and 6-holes
mixer. Also the result showed that if inlet convergency was smoother
than outlet divergency, the mixture get more homogenous, the reason
of that is in increasing turbulence in outlet divergency.
Abstract: Vapour recompression system has been used to
enhance reduction in energy consumption and improvement in
energy effectiveness of distillation columns. However, the effects of
certain parameters have not been taken into consideration. One of
such parameters is the column heat loss which has either been
assumed to be a certain percent of reboiler heat transfer or negligible.
The purpose of this study was to evaluate the heat loss from an
ethanol-water vapour recompression distillation column with
pressure increase across the compressor (VRCAS) and compare the
results obtained and its effect on some parameters in similar system
(VRCCS) where the column heat loss has been assumed or neglected.
Results show that the heat loss evaluated was higher when compared
with that obtained for the column VRCCS. The results also showed
that increase in heat loss could have significant effect on the total
energy consumption, reboiler heat transfer, the number of trays and
energy effectiveness of the column.
Abstract: The excessive consumption of fossil energies (electrical energy) during summer caused by the technological development involves more and more climate warming.
In order to reduce the worst impact of gas emissions produced from classical air conditioning, heat driven solar absorption chiller is pretty promising; it consists on using solar as motive energy which is clean and environmentally friendly to provide cold.
Solar absorption machine is composed by four components using Lithium Bromide /water as a refrigerating couple. LiBr- water is the most promising in chiller applications due to high safety, high volatility ratio, high affinity, high stability and its high latent heat. The lithium bromide solution is constitute by the salt lithium bromide which absorbs water under certain conditions of pressure and temperature however if the concentration of the solution is high in the absorption chillers; which exceed 70%, the solution will crystallize.
The main aim of this article is to study the phenomena of the crystallization and to evaluate how the dependence between the electric conductivity and the concentration which should be controlled.
Abstract: The aim of this paper is to emphasize and alleviate the effect of phase noise due to imperfect local oscillators on the performances of a Multi-Carrier CDMA system. After the cancellation of Common Phase Error (CPE), an iterative approach is introduced which iteratively estimates Inter-Carrier Interference (ICI) components in the frequency domain and cancels their contribution in the time domain. Simulation are conducted in order to investigate the achievable performances for several parameters, such as the spreading factor, the modulation order, the phase noise power and the transmission Signal-to-Noise Ratio.
Abstract: The problem of Small Area Estimation (SAE) is complex because of various information sources and insufficient data. In this paper, an approach for SAE is presented for decision-making at national, regional and local level. We propose an Empirical Best Linear Unbiased Predictor (EBLUP) as an estimator in order to combine several information sources to evaluate various indicators. First, we present the urban audit project and its environmental, social and economic indicators. Secondly, we propose an approach for decision making in order to estimate indicators. An application is used to validate the theoretical proposal. Finally, a decision support system is presented based on open-source environment.
Abstract: Traffic density, an indicator of traffic
conditions, is one of the most critical characteristics to
Intelligent Transport Systems (ITS). This paper investigates
recursive traffic density estimation using the information
provided from inductive loop detectors. On the basis of the
phenomenological relationship between speed and density, the
existing studies incorporate a state space model and update the
density estimate using vehicular speed observations via the
extended Kalman filter, where an approximation is made
because of the linearization of the nonlinear observation
equation. In practice, this may lead to substantial estimation
errors. This paper incorporates a suitable transformation to
deal with the nonlinear observation equation so that the
approximation is avoided when using Kalman filter to
estimate the traffic density. A numerical study is conducted. It
is shown that the developed method outperforms the existing
methods for traffic density estimation.
Abstract: In this present study, experimental work was
conducted to study the effectiveness of newly innovated steel-CFRP
composite (CFRP laminates sandwiched between two steel strips) as
stirrups. A total numbers of eight concrete beams were tested under
four point loads. Each beam measured 1600 mm long, 160mm width
and 240 mm depth. The beams were reinforced with different shear
reinforcements; one without stirrups, one with steel stirrups and six
with different types and numbers of steel-CRFR stirrups. Test results
indicated that the steel-CFRP stirrups had enhanced the shear
strength capacity of beams. Moreover, the tests revealed that steel-
CFRP stirrups reached to their ultimate tensile strength unlike FRP
stirrups which rupture at much lower level than their ultimate
strength as werereported in various researches.
Abstract: The objective of this paper is to compare the time
specification performance between conventional controller PID and
modern controller SMC for an inverted pendulum system. The goal is
to determine which control strategy delivers better performance with
respect to pendulum-s angle and cart-s position. The inverted
pendulum represents a challenging control problem, which
continually moves toward an uncontrolled state. Two controllers are
presented such as Sliding Mode Control (SMC) and Proportional-
Integral-Derivatives (PID) controllers for controlling the highly
nonlinear system of inverted pendulum model. Simulation study has
been done in Matlab Mfile and simulink environment shows that both
controllers are capable to control multi output inverted pendulum
system successfully. The result shows that Sliding Mode Control
(SMC) produced better response compared to PID control strategies
and the responses are presented in time domain with the details
analysis.
Abstract: This paper presents the fundamentals of Origami engineering and its application in nowadays as well as future industry. Several main cores of mathematical approaches such as Huzita- Hatori axioms, Maekawa and Kawasaki-s theorems are introduced briefly. Meanwhile flaps and circle packing by Robert Lang is explained to make understood the underlying principles in designing crease pattern. Rigid origami and its corrugation patterns which are potentially applicable for creating transformable or temporary spaces is discussed to show the transition of origami from paper to thick material. Moreover, some innovative applications of origami such as eyeglass, origami stent and high tech origami based on mentioned theories and principles are showcased in section III; while some updated origami technology such as Vacuumatics, self-folding of polymer sheets and programmable matter folding which could greatlyenhance origami structureare demonstrated in Section IV to offer more insight in future origami.
Abstract: Tourism is a phenomenon respected by the human communities since a long time ago. It has been evoloving continually based on a variety of social and economic needs and with respect to increasingly development of communication and considerable increase of tourist-s number and resulted exchange income has attained much out come such as employment for the communities. or the purpose of tourism development in this zone suitable times and locations need to be specified in the zone for the tourist-s attendance. One of the most important needs of the tourists is the knowledge of climate conditions and suitable times for sightseeing. In this survey, the climate trend condition has been identified for attending the tourists in Isfahan province using the modified tourism climate index (TCI) as well as SPSS, GIS, excel, surfer softwares. This index evoluates systematically the climate conditions for tourism affairs and activities using the monthly maximum mean parameters of daily temperature, daily mean temperature, minimum relative humidity, daily mean relative humidity, precipitation (mm), total sunny hours, wind speed and dust. The results obtaind using kendal-s correlation test show that the months January, February, March, April, May, June, July, August, September, October, November and December are significant and have an increasing trend that indicates the best condition for attending the tourists. S, P, T mean , T max and dust are estimated from 1976-2005 and do kendal-s correlation test again to see which parameter has been effective. Based on the test, we also observed on the effective parameters that the rate of dust in February, March, April, May, June, July, August, October and November is decreasing and precipitation in September and January is increasing and also the radiation rate in May and August is increasing that indicate a better condition of convenience. Maximum temperature in June is also decreasing. Isfahan province has two spring and fall peaks and the best places for tourism are in the north and western areas.
Abstract: In this paper we present a technique to speed up
ICA based on the idea of reducing the dimensionality of the data
set preserving the quality of the results. In particular we refer to
FastICA algorithm which uses the Kurtosis as statistical property
to be maximized. By performing a particular Johnson-Lindenstrauss
like projection of the data set, we find the minimum dimensionality
reduction rate ¤ü, defined as the ratio between the size k of the reduced
space and the original one d, which guarantees a narrow confidence
interval of such estimator with high confidence level. The derived
dimensionality reduction rate depends on a system control parameter
β easily computed a priori on the basis of the observations only.
Extensive simulations have been done on different sets of real world
signals. They show that actually the dimensionality reduction is very
high, it preserves the quality of the decomposition and impressively
speeds up FastICA. On the other hand, a set of signals, on which the
estimated reduction rate is greater than 1, exhibits bad decomposition
results if reduced, thus validating the reliability of the parameter β.
We are confident that our method will lead to a better approach to
real time applications.