Abstract: The Platform Screen Doors improve Indoor Air Quality
(IAQ) in the subway station; however, and the air quality is degraded
in the subway tunnel. CO2 concentration and indoor particulate matter
value are high in the tunnel. The IAQ level in subway tunnel degrades
by increasing the train movements. Air-curtain installation reduces
dusts, particles and moving toxic smokes and permits traffic by
generating virtual wall. The ventilation systems of the subway tunnel
need improvements to have better air-quality. Numerical analyses
might be effective tools analyze the flowfield inside the air-curtain
installed subway tunnel. The ANSYS CFX software is used for steady
computations of the airflow inside the tunnel. The single-track subway
tunnel has the natural shaft, the mechanical shaft, and the PSDs
installed stations. The height and width of the tunnel are 6.0 m and 4.0
m respectively. The tunnel is 400 m long and the air-curtain is installed
at the top of the tunnel. The thickness and the width of the air-curtain
are 0.08 m and 4 m respectively. The velocity of the air-curtain
changes between 20 - 30 m/s. Three cases are analyzed depending on
the installing location of the air-curtain. The discharged-air through
the natural shafts increases as the velocity of the air-curtain increases
when the air-curtain is installed between the mechanical and the
natural shafts. The pollutant-air is exhausted by the mechanical and the
natural shafts and remained air is pushed toward tunnel end. The
discharged-air through the natural shaft is low when the air-curtain
installed before the natural shaft. The mass flow rate decreases in the
tunnel after the mechanical shaft as the air-curtain velocity increases.
The computational results of the air-curtain installed tunnel become
basis for the optimum design study. The air-curtain installing location
is chosen between the mechanical and the natural shafts. The velocity
of the air-curtain is fixed as 25 m/s. The thickness and the blowing
angles of the air-curtain are the design variables for the optimum
design study. The object function of the design optimization is
maximizing the discharged air through the natural shaft.
Abstract: The paper presents the results of the European EIE
project “Realising the potential for small scale renewable energy
sources in the home – Kyotointhehome". The project's global aim is
to inform and educate teachers, students and their families so that
they can realise the need and can assess the potential for energy
efficiency (EE) measures and renewable energy sources (RES) in
their homes. The project resources were translated and trialled by 16
partners in 10 European countries.
A web-based methodology which will enable families to assess
how RES can be incorporated into energy efficient homes was
accomplished. The web application “KYOTOINHOME" will help
the citizens to identify what they can do to help their community
meet the Kyoto target for greenhouse gas reductions and prevent
global warming. This application provides useful information on how
the citizens can use renewable energy sources in their home to
provide space heating and cooling, hot water and electricity. A
methodology for assessing heat loss in a dwelling and application of
heat pump system was elaborated and will be implemented this year.
For schools, we developed a set of practical activities concerned with
preventing climate change through using renewable energy sources.
Complementary resources will also developed in the Romanian
research project “Romania Contribution to the European Targets
Regarding the Development of Renewable Energy Sources" -
PROMES.
Abstract: The paper presents a novel idea to control computer
mouse cursor movement with human eyes. In this paper, a working
of the product has been described as to how it helps the special
people share their knowledge with the world. Number of traditional
techniques such as Head and Eye Movement Tracking Systems etc.
exist for cursor control by making use of image processing in which
light is the primary source. Electro-oculography (EOG) is a new
technology to sense eye signals with which the mouse cursor can be
controlled. The signals captured using sensors, are first amplified,
then noise is removed and then digitized, before being transferred to
PC for software interfacing.
Abstract: Saturated hydraulic conductivity of Soil is an
important property in processes involving water and solute flow in
soils. Saturated hydraulic conductivity of soil is difficult to measure
and can be highly variable, requiring a large number of replicate
samples. In this study, 60 sets of soil samples were collected at
Saqhez region of Kurdistan province-IRAN. The statistics such as
Correlation Coefficient (R), Root Mean Square Error (RMSE), Mean
Bias Error (MBE) and Mean Absolute Error (MAE) were used to
evaluation the multiple linear regression models varied with number
of dataset. In this study the multiple linear regression models were
evaluated when only percentage of sand, silt, and clay content (SSC)
were used as inputs, and when SSC and bulk density, Bd, (SSC+Bd)
were used as inputs. The R, RMSE, MBE and MAE values of the 50
dataset for method (SSC), were calculated 0.925, 15.29, -1.03 and
12.51 and for method (SSC+Bd), were calculated 0.927, 15.28,-1.11
and 12.92, respectively, for relationship obtained from multiple
linear regressions on data. Also the R, RMSE, MBE and MAE values
of the 10 dataset for method (SSC), were calculated 0.725, 19.62, -
9.87 and 18.91 and for method (SSC+Bd), were calculated 0.618,
24.69, -17.37 and 22.16, respectively, which shows when number of
dataset increase, precision of estimated saturated hydraulic
conductivity, increases.
Abstract: The objective of this work is to study the influence of the properties of the substrate on the retrofit (thin repair) of damaged concrete elements, with the SCC. Fluidity, principal characteristic of the SCC, would enable it to cover and adhere to the concrete to be repaired. Two aspects of repair are considered, the bond (Adhesion) and the tensile strength and the cracking. The investigation is experimental; It was conducted over test specimens made up of ordinary concrete prepared and hardened in advance (the material to be repaired) over which a self compacting concrete layer is cast. Three alternatives of SC concrete and one ordinary concrete (comparison) were tested. It appears that the self-compacting concrete constitutes a good material for repairing. It follows perfectly the surfaces- forms to be repaired and allows a perfect bond. Fracture tests made on specimens of self-compacting concrete show a brittle behaviour. However when a small percentage of fibres is added, the resistance to cracking is very much improve.
Abstract: Deprivation indices are widely used in public health
study. These indices are also referred as the index of inequalities or
disadvantage. Even though, there are many indices that have been
built before, it is believed to be less appropriate to use the existing
indices to be applied in other countries or areas which had different
socio-economic conditions and different geographical characteristics.
The objective of this study is to construct the index based on the
geographical and socio-economic factors in Peninsular Malaysia
which is defined as the weighted household-based deprivation index.
This study has employed the variables based on household items,
household facilities, school attendance and education level obtained
from Malaysia 2000 census report. The factor analysis is used to
extract the latent variables from indicators, or reducing the
observable variable into smaller amount of components or factor.
Based on the factor analysis, two extracted factors were selected,
known as Basic Household Amenities and Middle-Class Household
Item factor. It is observed that the district with a lower index values
are located in the less developed states like Kelantan, Terengganu
and Kedah. Meanwhile, the areas with high index values are located
in developed states such as Pulau Pinang, W.P. Kuala Lumpur and
Selangor.
Abstract: Deep cold rolling (DCR) and low plasticity burnishing (LPB) process are cold working processes, which easily produce a smooth and work-hardened surface by plastic deformation of surface irregularities. The present study focuses on the surface roughness and surface hardness aspects of AISI 4140 work material, using fractional factorial design of experiments. The assessment of the surface integrity aspects on work material was done, in order to identify the predominant factors amongst the selected parameters. They were then categorized in order of significance followed by setting the levels of the factors for minimizing surface roughness and/or maximizing surface hardness. In the present work, the influence of main process parameters (force, feed rate, number of tool passes/overruns, initial roughness of the work piece, ball material, ball diameter and lubricant used) on the surface roughness and the hardness of AISI 4140 steel were studied for both LPB and DCR process and the results are compared. It was observed that by using LPB process surface hardness has been improved by 167% and in DCR process surface hardness has been improved by 442%. It was also found that the force, ball diameter, number of tool passes and initial roughness of the workpiece are the most pronounced parameters, which has a significant effect on the work piece-s surface during deep cold rolling and low plasticity burnishing process.
Abstract: Some methodologies were compared in providing
erosion maps of surface, rill and gully and erosion features, in
research which took place in the Varamin sub-basin, north-east
Tehran, Iran. A photomorphic unit map was produced from
processed satellite images, and four other maps were prepared by the
integration of different data layers, including slope, plant cover,
geology, land use, rocks erodibility and land units. Comparison of
ground truth maps of erosion types and working unit maps indicated
that the integration of land use, land units and rocks erodibility layers
with satellite image photomorphic units maps provide the best
methods in producing erosion types maps.
Abstract: This paper is based on a study conducted in 2006 to assess the impact of computer usage on health of National Institute for Medical Research (NIMR) staff. NIMR being a research Institute, most of its staff spend substantial part of their working time on computers. There was notion among NIMR staff on possible prolonged computer usage health hazards. Hence, a study was conducted to establish facts and possible mitigation measures. A total of 144 NIMR staff were involved in the study of whom 63.2% were males and 36.8% females aged between 20 and 59 years. All staff cadres were included in the sample. The functions performed by Institute staff using computers includes; data management, proposal development and report writing, research activities, secretarial duties, accounting and administrative duties, on-line information retrieval and online communication through e-mail services. The interviewed staff had been using computers for 1-8 hours a day and for a period ranging from 1 to 20 years. The study has indicated ergonomic hazards for a significant proportion of interviewees (63%) of various kinds ranging from backache to eyesight related problems. The authors highlighted major issues which are substantially applicable in preventing occurrences of computer related problems and they urged NIMR Management and/or the government of Tanzania opts to adapt their practicability.
Abstract: Sedimentation in reservoirs and the corresponding
loss of storage capacity is one of the most serious problems in dam
engineering. Pressurized flushing, a way to remove sediments from the reservoir, is flushing under a pressurized flow condition and
nearly constant water level. Pressurized flushing has only local
effects around the outlet. Sediment in the vicinity of the outlet openings is scoured and a funnel shaped crater is created. In this study, the temporal development of flushing cone under various
hydraulic conditions was studied experimentally. Time variations of
parameters such as maximum length and width of flushing and also
depth of scouring cone was measured. Results indicated that an
increase in flow velocity (and consequently in Froude number)
established new hydraulically conditions for flushing mechanism and
so a sudden growth was observed in the amount of sediment released
and also scouring dimenssions. In addition, a set of nondimensional
relationships were identified for temporal variations of flushing scour
dimenssions, which can eventuallt be used to estimate the development of flushing cone.
Abstract: One-way functions are functions that are easy to
compute but hard to invert. Their existence is an open conjecture; it
would imply the existence of intractable problems (i.e. NP-problems
which are not in the P complexity class).
If true, the existence of one-way functions would have an impact
on the theoretical framework of physics, in particularly, quantum
mechanics. Such aspect of one-way functions has never been shown
before.
In the present work, we put forward the following.
We can calculate the microscopic state (say, the particle spin in the
z direction) of a macroscopic system (a measuring apparatus
registering the particle z-spin) by the system macroscopic state (the
apparatus output); let us call this association the function F. The
question is: can we compute the function F in the inverse direction?
In other words, can we compute the macroscopic state of the system
through its microscopic state (the preimage F -1)?
In the paper, we assume that the function F is a one-way function.
The assumption implies that at the macroscopic level the Schrödinger
equation becomes unfeasible to compute. This unfeasibility plays a
role of limit of the validity of the linear Schrödinger equation.
Abstract: The study describes chitosan membrane platform
modified with nanostructure pattern which using nanotechnology to
fabricate. The cell-substrate interaction between neuro-2a neuroblasts
cell lines and chitosan membrane (flat, nanostructure and
nanostructure pattern types) was investigated. The adhered
morphology of neuro-2a cells depends on the topography of chitosan
surface. We have found that neuro-2a showed different morphogenesis
when cells adhered on flat and nanostructure chitosan membrane. The
cell projected area of neuro-2a on flat chitosan membrane is larger
than on nanostructure chitosan membrane. In addition, neuro-2a cells
preferred to adhere on flat chitosan surface region than on
nanostructure chitosan membrane to immobilize and differentiation.
The experiment suggests surface topography can be used as a critical
mechanism to isolate group of neuro-2a to a particular rectangle area
on chitosan membrane. Our finding will provide a platform to take
patch clamp to record electrophysiological behavior about neurons in
vitro in the future.
Abstract: Standard packaging and interconnection technologies
of power devices have difficulties meeting the increasing thermal
demands of new application fields of power electronics devices.
Main restrictions are the decreasing reliability of bond-wires and
solder layers with increasing junction temperature. In the last few
years intensive efforts have been invested in developing new
packaging and interconnection solutions which may open a path to
future application of power devices. In this paper, the main failure
mechanisms of power devices are described and principle of new
packaging and interconnection concepts and their power cycling
reliability are presented.
Abstract: In this paper we present two novel 1-bit full adder
cells in dynamic logic style. NP-CMOS (Zipper) and Multi-Output
structures are used to design the adder blocks. Characteristic of
dynamic logic leads to higher speeds than the other standard static
full adder cells. Using HSpice and 0.18┬Ám CMOS technology
exhibits a significant decrease in the cell delay which can result in a
considerable reduction in the power-delay product (PDP). The PDP
of Multi-Output design at 1.8v power supply is around 0.15 femto
joule that is 5% lower than conventional dynamic full adder cell and
at least 21% lower than other static full adders.
Abstract: Fermented beverages have high expression in the
market for beverages in general, is increasingly valued in situations
where the characteristic aroma and flavor of the material that gave
rise to them are kept after processing. This study aimed to develop a
distilled beverage from passion fruit, and assess, by sensory tests and
chromatographic profile, the influence of different treatments (FM1-
spirit with pulp addiction and FM2 – spirit with bigger ratio of pulp
in must) in the setting of volatiles in the fruit drink, and performing
chemical characterization taking into account the main parameters of
quality established by the legislation. The chromatograms and the
first sensorial tests had indicated that sample FM1 possess better
characteristics of aroma, as much of how much quantitative the
qualitative point of view. However, it analyzes it sensorial end
(preference test) disclosed the biggest preference of the cloth provers
for sample FM2-2 (note 7.93), being the attributes of decisive color
and flavor in this reply, confirmed for the observed values lowest of
fixed and total acidity in the samples of treatment FM2.
Abstract: This paper develops driver reaction-time models for
car-following analysis based on human factors. The reaction time
was classified as brake-reaction time (BRT) and
acceleration/deceleration reaction time (ADRT). The BRT occurs
when the lead vehicle is barking and its brake light is on, while the
ADRT occurs when the driver reacts to adjust his/her speed using the
gas pedal only. The study evaluates the effect of driver
characteristics and traffic kinematic conditions on the driver reaction
time in a car-following environment. The kinematic conditions
introduced urgency and expectancy based on the braking behaviour
of the lead vehicle at different speeds and spacing. The kinematic
conditions were used for evaluating the BRT and are classified as
normal, surprised, and stationary. Data were collected on a driving
simulator integrated into a real car and included the BRT and ADRT
(as dependent variables) and driver-s age, gender, driving experience,
driving intensity (driving hours per week), vehicle speed, and
spacing (as independent variables). The results showed that there was
a significant difference in the BRT at normal, surprised, and
stationary scenarios and supported the hypothesis that both urgency
and expectancy had significant effects on BRT. Driver-s age, gender,
speed, and spacing were found to be significant variables for the
BRT in all scenarios. The results also showed that driver-s age and
gender were significant variables for the ADRT. The research
presented in this paper is part of a larger project to develop a driversensitive
in-vehicle rear-end collision warning system.
Abstract: ICA which is generally used for blind source separation
problem has been tested for feature extraction in Speech recognition
system to replace the phoneme based approach of MFCC. Applying
the Cepstral coefficients generated to ICA as preprocessing has
developed a new signal processing approach. This gives much better
results against MFCC and ICA separately, both for word and speaker
recognition. The mixing matrix A is different before and after MFCC
as expected. As Mel is a nonlinear scale. However, cepstrals
generated from Linear Predictive Coefficient being independent
prove to be the right candidate for ICA. Matlab is the tool used for
all comparisons. The database used is samples of ISOLET.
Abstract: Technology changes have been acknowledged as a
critical factor in determining competitiveness of organization. Under
such environment, the right anticipation of technology change has
been of huge importance in strategic planning. To monitor technology
change, technology forecasting (TF) is frequently utilized. In
academic perspective, TF has received great attention for a long time.
However, few researches have been conducted to provide overview of
the TF literature. Even though some studies deals with review of TF
research, they generally focused on type and characteristics of various
TF, so hardly provides information about patterns of TF research and
which TF method is used in certain technology industry. Accordingly,
this study profile developments in and patterns of scholarly research in
TF over time. Also, this study investigates which technology
industries have used certain TF method and identifies their
relationships. This study will help in understanding TF research trend
and their application area.
Abstract: In order to calculate the flexural strength of
normal-strength concrete (NSC) beams, the nonlinear actual concrete
stress distribution within the compression zone is normally replaced
by an equivalent rectangular stress block, with two coefficients of α
and β to regulate the intensity and depth of the equivalent stress
respectively. For NSC beams design, α and β are usually assumed
constant as 0.85 and 0.80 in reinforced concrete (RC) codes. From an
earlier investigation of the authors, α is not a constant but significantly
affected by flexural strain gradient, and increases with the increasing
of strain gradient till a maximum value. It indicates that larger
concrete stress can be developed in flexure than that stipulated by
design codes. As an extension and application of the authors- previous
study, the modified equivalent concrete stress block is used here to
produce a series of design charts showing the maximum design limits
of flexural strength and ductility of singly- and doubly- NSC beams,
through which both strength and ductility design limits are improved
by taking into account strain gradient effect.
Abstract: Public administration institutions in cooperation with
politicians are not the sole policy decision makers in full meaning
any longer. Meanwhile, a special role, namely steering the decision
making process, could be delegated to them.
Despite the wide scientific discussion on different aspects what
has direct impact on policy creation, there is a lack of holistic
practical managerial advice, which could integrate infrastructure of
policy decision making with intellectual capital and with
interconnection of partnership. The proposed harmonized decision
making model of process, people and partnership entitled by
acronym HM-3P is analyzed as a framework for implementation of
public administration steering role seeking the coherent social
involvement in policy decision making.