Abstract: Mycophenolic acid “MPA" is a secondary metabolite
of Penicillium bervicompactum with antibiotic and
immunosuppressive properties. In this study, fermentation process
was established for production of mycophenolic acid by Penicillium
bervicompactum MUCL 19011 in shake flask. The maximum MPA
production, product yield and productivity were 1.379 g/L, 18.6 mg/g
glucose and 4.9 mg/L.h respectively. Glucose consumption, biomass
and MPA production profiles were investigated during fermentation
time. It was found that MPA production starts approximately after
180 hours and reaches to a maximum at 280 h. In the next step, the
effects of methionine and acetate concentrations on MPA production
were evaluated. Maximum MPA production, product yield and
productivity (1.763 g/L, 23.8 mg/g glucose and 6.30 mg/L. h
respectively) were obtained with using 2.5 g/L methionine in culture
medium. Further addition of methionine had not more positive effect
on MPA production. Finally, results showed that the addition of
acetate to the culture medium had not any observable effect on MPA
production
Abstract: Results are presented from a combined experimental
and modeling study undertaken to understand the effect of fuel spray
angle on soot production in turbulent liquid spray flames. The
experimental work was conducted in a cylindrical laboratory furnace
at fuel spray cone angle of 30º, 45º and 60º. Soot concentrations
inside the combustor are measured by filter paper technique. The soot
concentration is modeled by using the soot particle number density
and the mass density based acetylene concentrations. Soot oxidation
occurred by both hydroxide radicals and oxygen molecules. The
comparison of calculated results against experimental measurements
shows good agreement. Both the numerical and experimental results
show that the peak value of soot and its location in the furnace
depend on fuel spray cone angle. An increase in spray angle enhances
the evaporating rate and peak temperature near the nozzle. Although
peak soot concentration increase with enhance of fuel spray angle but
soot emission from the furnace decreases.
Abstract: Multifunctional structures are a potentially disruptive
technology that allows for significant mass savings on spacecraft.
The specific concept addressed herein is that of a multifunctional
power structure. In this paper, a parametric optimisation of the
design of such a structure that uses commercially available battery
cells is presented. Using numerical modelling, it was found that there
exists several trade-offs aboutthe conflict between the capacity of the
panel and its mechanical properties. It was found that there is no
universal optimal location for the cells. Placing them close to the
mechanical interfaces increases loading in the mechanically weak
cells whereas placing them at the centre of the panel increases the
stress inthe panel and reduces the stiffness of the structure.
Abstract: Bioprocesses are appreciated as difficult to control because their dynamic behavior is highly nonlinear and time varying, in particular, when they are operating in fed batch mode. The research objective of this study was to develop an appropriate control method for a complex bioprocess and to implement it on a laboratory plant. Hence, an intelligent control structure has been designed in order to produce biomass and to maximize the specific growth rate.
Abstract: The present work demonstrates the design and simulation of a fuzzy control of an air conditioning system at different pressures. The first order Sugeno fuzzy inference system is utilized to model the system and create the controller. In addition, an estimation of the heat transfer rate and water mass flow rate injection into or withdraw from the air conditioning system is determined by the fuzzy IF-THEN rules. The approach starts by generating the input/output data. Then, the subtractive clustering algorithm along with least square estimation (LSE) generates the fuzzy rules that describe the relationship between input/output data. The fuzzy rules are tuned by Adaptive Neuro-Fuzzy Inference System (ANFIS). The results show that when the pressure increases the amount of water flow rate and heat transfer rate decrease within the lower ranges of inlet dry bulb temperatures. On the other hand, and as pressure increases the amount of water flow rate and heat transfer rate increases within the higher ranges of inlet dry bulb temperatures. The inflection in the pressure effect trend occurs at lower temperatures as the inlet air humidity increases.
Abstract: In this paper the vibration behaviors of a structure equipped with a tuned liquid column damper (TLCD) under a harmonic type of earthquake loading are studied. However, due to inherent nonlinear liquid damping, it is no doubt that a great deal of computational effort is required to search the optimum parameters of the TLCD, numerically. Therefore by linearization the equation of motion of the single degree of freedom structure equipped with the TLCD, the closed form solutions of the TLCD-structure system are derived. To find the reliability of the analytical method, the results have been compared with other researcher and have good agreement. Further, the effects of optimal design parameters such as length ratio and mass ratio on the performance of the TLCD for controlling the responses of a structure are investigated by using the harmonic type of earthquake excitation. Finally, the Citicorp Center which has a very flexible structure is used as an example to illustrate the design procedure for the TLCD under the earthquake excitation.
Abstract: We report the results of an lattice Boltzmann
simulation of magnetohydrodynamic damping of sidewall convection
in a rectangular enclosure filled with a porous medium. In particular
we investigate the suppression of convection when a steady magnetic
field is applied in the vertical direction. The left and right vertical
walls of the cavity are kept at constant but different temperatures
while both the top and bottom horizontal walls are insulated. The
effects of the controlling parameters involved in the heat transfer and
hydrodynamic characteristics are studied in detail. The heat and mass
transfer mechanisms and the flow characteristics inside the enclosure
depended strongly on the strength of the magnetic field and Darcy
number. The average Nusselt number decreases with rising values of
the Hartmann number while this increases with increasing values of
the Darcy number.
Abstract: The paper presents a one-dimensional transient
mathematical model of thermal oil-water two-phase emulsion flows
in pipes. The set of the mass, momentum and enthalpy conservation
equations for the continuous fluid and droplet phases are solved. Two
friction correlations for the continuous fluid phase to wall friction are
accounted for in the model and tested. The aerodynamic drag force
between the continuous fluid phase and droplets is modeled, too. The
density and viscosity of both phases are assumed to be constant due
to adiabatic experimental conditions. The proposed mathematical
model is validated on the experimental measurements of oil-water
emulsion flows in horizontal pipe [1,2]. Numerical analysis on
single- and two-phase oil-water flows in a pipe is presented in the
paper. The continuous oil flow having water droplets is simulated.
Predictions, which are performed by using the presented model, show
excellent agreement with the experimental data if the water fraction is
equal or less than 10%. Disagreement between simulations and
measurements is increased if the water fraction is larger than 10%.
Abstract: Team distillation assisted by microwave extraction
(SDAM) considered as accelerated technique extraction is a
combination of microwave heating and steam distillation, performed
at atmospheric pressure. SDAM has been compared with the same
technique coupled with the cryogrinding of seeds (SDAM -CG).
Isolation and concentration of volatile compounds are performed by a
single stage for the extraction of essential oil from Cuminum
cyminum seeds. The essential oils extracted by these two methods for
5 min were quantitatively (yield) and qualitatively (aromatic profile)
no similar. These methods yield an essential oil with higher amounts
of more valuable oxygenated compounds, and allow substantial
savings of costs, in terms of time, energy and plant material. SDAM
and SDAM-CG is a green technology and appears as a good
alternative for the extraction of essential oils from aromatic plants.
Abstract: Recently, a growing interest has emerged on the
development of new and efficient energy sources, due to the inevitable extinction of the nonrenewable energy reserves. One of
these alternative sources which has a great potential and sustainability to meet up the energy demand is biomass energy. This
significant energy source can be utilized with various energy
conversion technologies, one of which is biomass gasification in
supercritical water.
Water, being the most important solvent in nature, has very important characteristics as a reaction solvent under supercritical
circumstances. At temperatures above its critical point (374.8oC and
22.1 MPa), water becomes more acidic and its diffusivity increases.
Working with water at high temperatures increases the thermal
reaction rate, which in consequence leads to a better dissolving of the
organic matters and a fast reaction with oxygen. Hence, supercritical water offers a control mechanism depending on solubility, excellent
transport properties based on its high diffusion ability and new reaction possibilities for hydrolysis or oxidation.
In this study the gasification of a real biomass, namely olive mill
wastewater (OMW), in supercritical water is investigated with the
use of Pt/Al2O3 and Ni/Al2O3 catalysts. OMW is a by-product
obtained during olive oil production, which has a complex nature
characterized by a high content of organic compounds and
polyphenols. These properties impose OMW a significant pollution
potential, but at the same time, the high content of organics makes
OMW a desirable biomass candidate for energy production.
All of the catalytic gasification experiments were made with five
different reaction temperatures (400, 450, 500, 550 and 600°C),
under a constant pressure of 25 MPa. For the experiments conducted
with Ni/Al2O3 catalyst, the effect of five reaction times (30, 60, 90,
120 and 150 s) was investigated. However, procuring that similar
gasification efficiencies could be obtained at shorter times, the experiments were made by using different reaction times (10, 15, 20,
25 and 30 s) for the case of Pt/Al2O3 catalyst. Through these experiments, the effects of temperature, time and catalyst type on the
gasification yields and treatment efficiencies were investigated.
Abstract: The hydromagnetic flow of a Maxwell fluid past a vertical stretching sheet with thermophoresis is considered. The impact of chemical reaction species to the flow is analyzed for the first time by using the homotopy analysis method (HAM). The h-curves for the flow boundary layer equations are presented graphically. Several values of wall skin friction, heat and mass transfer are obtained and discussed.
Abstract: In this study, we used a two-stage process and
potassium hydroxide (KOH) to transform waste biomass (rice straw)
into activated carbon and then evaluated the adsorption capacity of the
waste for removing carbofuran from an aqueous solution. Activated
carbon was fast and effective for the removal of carbofuran because of
its high surface area. The native and carbofuran-loaded adsorbents
were characterized by elemental analysis. Different adsorption
parameters, such as the initial carbofuran concentration, contact time,
temperature and pH for carbofuran adsorption, were studied using a
batch system. This study demonstrates that rice straw can be very
effective in the adsorption of carbofuran from bodies of water.
Abstract: Arthrobacter viscosus biomass was used for Cr(VI)
biosorption. The effect of pH on Cr(VI) reduction and removal from
aqueous solution was studied in the range of 1-4. The Cr(VI) removal
involves both redox reaction and adsorption of metal ions on biomass
surface. The removal rate of Cr(VI) was enhanced by very acid
conditions, while higher solution pH values favored the removal of
total chromium. The best removal efficiency and uptake were
reached at pH 4, 72.5 % and 12.6 mgCr/gbiomass, respectively.
Abstract: In this paper we present high performance
dynamically allocated multi-queue (DAMQ) buffer schemes for fault
tolerance systems on chip applications that require an interconnection
network. Two virtual channels shared the same buffer space. Fault
tolerant mechanisms for interconnection networks are becoming a
critical design issue for large massively parallel computers. It is also
important to high performance SoCs as the system complexity keeps
increasing rapidly. On the message switching layer, we make
improvement to boost system performance when there are faults
involved in the components communication. The proposed scheme is
when a node or a physical channel is deemed as faulty, the previous
hop node will terminate the buffer occupancy of messages destined
to the failed link. The buffer usage decisions are made at switching
layer without interactions with higher abstract layer, thus buffer
space will be released to messages destined to other healthy nodes
quickly. Therefore, the buffer space will be efficiently used in case
fault occurs at some nodes.
Abstract: In order to evaluate the relationship between the sulphur (S), glucose (G), nitrogen (N) and plant residues (st), sulphur immobilization and microbial transformation were monitored in five soil samples from 0-30 cm of Bastam farmers fields of Shahrood area following 11 treatments with different levels of Sulphur (S), glucose (G), N and plant residues (wheat straw) in a randomized block design with three replications and incubated over 20, 45 and 60 days, the immobilization of SO4 -2-S presented as a percentage of that added, was inversely related to its addition rate. Additions of glucose and plant residues increased with the C-to-S ratio of the added amendments, irrespective of their origins (glucose and plant residues). In the presence of C sources (glucose or plant residues). N significantly increased the immobilization of SO4 -2-S, whilst the effect of N was insignificant in the absence of a C amendment. In first few days the amounts of added SO4 -2-S immobilized were linearly correlated with the amounts of added S recovered in the soil microbial biomass. With further incubation the proportions of immobilized SO4 -2-S remaining as biomass-S decreased. Decrease in biomass-S was thought to be due to the conversion of biomass-S into soil organic-S. Glucose addition increased the immobilization (microbial utilization and incorporation into the soil organic matter) of native soil SO4 -2-S. However, N addition enhance the mineralization of soil organic-S, increasing the concentration of SO4 - 2-S in soil.
Abstract: In this study is presented a general methodology to
predict the performance of a continuous near-critical fluid extraction
process to remove compounds from aqueous solutions using hollow
fiber membrane contactors. A comprehensive 2D mathematical
model was developed to study Porocritical extraction process. The
system studied in this work is a membrane based extractor of ethanol
and acetone from aqueous solutions using near-critical CO2.
Predictions of extraction percentages obtained by simulations have
been compared to the experimental values reported by Bothun et al.
[5]. Simulations of extraction percentage of ethanol and acetone
show an average difference of 9.3% and 6.5% with the experimental
data, respectively. More accurate predictions of the extraction of
acetone could be explained by a better estimation of the transport
properties in the aqueous phase that controls the extraction of this
solute.
Abstract: Salinity is a measure of the amount of salts in the
water. Total Dissolved Solids (TDS) as salinity parameter are often
determined using laborious and time consuming laboratory tests, but
it may be more appropriate and economical to develop a method
which uses a more simple soil salinity index. Because dissolved ions
increase salinity as well as conductivity, the two measures are
related. The aim of this research was determine of constant
coefficients for predicting of Total Dissolved Solids (TDS) based on
Electrical Conductivity (EC) with Statistics of Correlation
coefficient, Root mean square error, Maximum error, Mean Bias
error, Mean absolute error, Relative error and Coefficient of residual
mass. For this purpose, two experimental areas (S1, S2) of Khuzestan
province-IRAN were selected and four treatments with three
replications by series of double rings were applied. The treatments
were included 25cm, 50cm, 75cm and 100cm water application. The
results showed the values 16.3 & 12.4 were the best constant
coefficients for predicting of Total Dissolved Solids (TDS) based on
EC in Pilot S1 and S2 with correlation coefficient 0.977 & 0.997 and
191.1 & 106.1 Root mean square errors (RMSE) respectively.
Abstract: We report the results of an lattice Boltzmann
simulation of magnetohydrodynamic damping of sidewall convection
in a rectangular enclosure filled with a porous medium. In particular
we investigate the suppression of convection when a steady magnetic
field is applied in the vertical direction. The left and right vertical
walls of the cavity are kept at constant but different temperatures
while both the top and bottom horizontal walls are insulated. The
effects of the controlling parameters involved in the heat transfer and
hydrodynamic characteristics are studied in detail. The heat and mass
transfer mechanisms and the flow characteristics inside the enclosure
depended strongly on the strength of the magnetic field and Darcy
number. The average Nusselt number decreases with rising values of
the Hartmann number while this increases with increasing values of
the Darcy number.
Abstract: This paper studies the duration or survival time of commercial banks active in the Moscovian three month Rouble deposits market, during the 1994-1997 period. The privatization process of the Russian commercial banking industry, after the 1988 banking reform, caused a massive entry of new banks followed by a period of high rates of exit. As a consequence, many firms went bankrupt without refunding their deposits. Therefore, both for the banks and for the banks- depositors, it is of interest to analyze which are the significant characteristics that motivate the exit or the closing of the bank. We propose a different methodology based on penalized weighted least squares which represents a very general, flexible and innovative approach for this type of analysis. The more relevant results are that smaller banks exit sooner, banks that enter the market in the last part of the study have shorter durations. As expected, the more experienced banks have a longer duration in the market. In addition, the mean survival time is lower for banks which offer extreme interest rates.
Abstract: Properties of cement pastes with fine-ground ceramics
used as an alternative binder replacing Portland cement up to 20% of
its mass are investigated. At first, the particle size distribution of
cement and fine-ground ceramics is measured using laser analyser.
Then, the material properties are studied in the early hardening
period up to 28 days. The hydration process of studied materials is
monitored by electrical conductivity measurement using TDR
sensors. The changes of materials- structures within the hardening are
observed using pore size distribution measurement. The compressive
strength measurements are done as well. Experimental results show
that the replacement of Portland cement by fine-ground ceramics in
the amount of up to 20% by mass is acceptable solution from the
mechanical point of view. One can also assume similar physical
properties of designed materials to the reference material with only
Portland cement as binder.