Abstract: Biomass is becoming a large renewable resource for
power generation; it is involved in higher frequency in
environmentally clean processes, and even it is used for biofuels
preparation. On the other hand, hydrogen – other energy source – can
be produced in a variety of methods including gasification of
biomass. In this study, the production of hydrogen by gasification of
biomass waste is examined. This work explores the production of a
gaseous mixture with high power potential from Amazonas´ specie
known as copoazu, using a counter-flow fixed-bed bioreactor.
Abstract: The development of renewable energies - particularly energy from wind, water, solar power and biomass - is a central aim of the European Commission's energy policy. There are several reasons for this choice: renewable energies are sustainable, nonpolluting, widely available and clean. Increasing the share of renewable energy in the energy balance enhances sustainability. It also helps to improve the security of energy supply by reducing the Community's growing dependence on imported energy sources.In this paper it was studied the possibility to realize three photovoltaic systems in the Italian Natural Park “Gola della Rossa e di Frasassi". The first photovoltaic system is a grid-connected system for Services and Documentation Center of Castelletta with a nominal power of about 6 kWp. The second photovoltaic system is a grid-connected integrated system on the ticket office-s roof with a nominal power of about 4 kWp. The third project is set up by five grid-connected systems integrated on the roofs of the bungalows in Natural Park-s tourist camping with a nominal power of about 10 kWp. The electricity which is generated by all these plants is purchased according to the Italian program called “Conto Energia". Economical analysis and the amount of the avoided CO2 emissions are elaborated for these photovoltaic systems.
Abstract: The objective of this paper is to study the analysis and testing for determining the torsional stiffness of the student formula-s space frame. From past study, the space frame for Chulalongkorn University Student Formula team used in 2011 TSAE Auto Challenge Student Formula in Thailand was designed by considering required mass and torsional stiffness based on the numerical method and experimental method. The numerical result was compared with the experimental results to verify the torsional stiffness of the space frame. It can be seen from the large error of torsional stiffness of 2011 frame that the experimental result can not verify by the numerical analysis due to the different between the numerical model and experimental setting. In this paper, the numerical analysis and experiment of the same 2011 frame model is performed by improving the model setting. The improvement of both numerical analysis and experiment are discussed to confirm that the models from both methods are same. After the frame was analyzed and tested, the results are compared to verify the torsional stiffness of the frame. It can be concluded that the improved analysis and experiments can used to verify the torsional stiffness of the space frame.
Abstract: An unstructured finite volume numerical model is
presented here for simulating shallow-water flows with wetting and
drying fronts. The model is based on the Green-s theorem in
combination with Chorin-s projection method. A 2nd-order upwind
scheme coupled with a Least Square technique is used to handle
convection terms. An Wetting and drying treatment is used in the
present model to ensures the total mass conservation. To test it-s
capacity and reliability, the present model is used to solve the
Parabolic Bowl problem. We compare our numerical solutions with
the corresponding analytical and existing standard numerical results.
Excellent agreements are found in all the cases.
Abstract: The stability of Newtonian and Non-Newtonian extending films under local or global heating or cooling conditions are considered. The thickness-averaged mass, momentum and energy equations with convective and radiative heat transfer are derived, both for Newtonian and non-Newtonian fluids (Maxwell, PTT and Giesekus models considered). The stability of the system is explored using either eigenvalue analysis or transient simulations. The results showed that the influence of heating and cooling on stability strongly depends on the magnitude of the Peclet number. Examples of stabilization or destabilization of heating or cooling are shown for Pe
Abstract: Recently there has been a growing interest in the field
of bio-mimetic robots that resemble the behaviors of an insect or an
aquatic animal, among many others. One of various bio-mimetic robot
applications is to explore pipelines, spotting any troubled areas or
malfunctions and reporting its data. Moreover, the robot is able to
prepare for and react to any abnormal routes in the pipeline. Special
types of mobile robots are necessary for the pipeline monitoring tasks.
In order to move effectively along a pipeline, the robot-s movement
will resemble that of insects or crawling animals. When situated in
massive pipelines with complex routes, the robot places fixed sensors
in several important spots in order to complete its monitoring. This
monitoring task is to prevent a major system failure by preemptively
recognizing any minor or partial malfunctions. Areas uncovered by
fixed sensors are usually impossible to provide real-time observation
and examination, and thus are dependent on periodical offline
monitoring. This paper proposes a monitoring system that is able to
monitor the entire area of pipelines–with and without fixed
sensors–by using the bio-mimetic robot.
Abstract: Biofuels, like biobutanol, have been recognized for
being renewable and sustainable fuels which can be produced from
lignocellulosic biomass. To convert lignocellulosic biomass to
biofuel, pretreatment process is an important step to remove
hemicelluloses and lignin to improve enzymatic hydrolysis. Dilute
acid pretreatment has been successful developed for pretreatment of
corncobs and the optimum conditions of dilute sulfuric and
phosphoric acid pretreatment were obtained at 120 °C for 5 min with
15:1 liquid to solid ratio and 140 °C for 10 min with 10:1 liquid to
solid ratio, respectively. The result shows that both of acid
pretreatments gave the content of total sugar approximately 34–35
g/l. In case of inhibitor content (furfural), phosphoric acid
pretreatment gives higher than sulfuric acid pretreatment.
Characterizations of corncobs after pretreatment indicate that both of
acid pretreatments can improve enzymatic accessibility and the better
results present in corncobs pretreated with sulfuric acid in term of
surface area, crystallinity, and composition analysis.
Abstract: Independent component analysis (ICA) is a computational method for finding underlying signals or components from multivariate statistical data. The ICA method has been successfully applied in many fields, e.g. in vision research, brain imaging, geological signals and telecommunications. In this paper, we apply the ICA method to an analysis of mass spectra of oligomeric species emerged from aluminium sulphate. Mass spectra are typically complex, because they are linear combinations of spectra from different types of oligomeric species. The results show that ICA can decomposite the spectral components for useful information. This information is essential in developing coagulation phases of water treatment processes.
Abstract: Introduction: Obesity is a major health risk issue in
the present day of life for one and all globally. Obesity is one of the
major concerns for public health according to recent increasing trends
in obesity-related diseases such as Type 2 diabetes. ( Kazuya,
1994).and hyperlipidemia, (Sakata,1990) .which are more prevalent
in Japanese adults with body mass index (BMI) values Z25 kg/m2.(
Japanese Ministry of Health and Welfare,1997). The purpose of the
study was to assess the effect of twelve weeks of brisk walking on
blood pressure and body mass index, anthropometric measurements
of obese males. Method: Thirty obese (BMI= above 30) males, aged
18 to 22 years, were selected from King Fahd University of
Petroleum & Minerals, Saudi Arabia. The subject-s height (cm) was
measured using a stadiometer and body mass (kg) was measured with
a electronic weighing machine. BMI was subsequently calculated
(kg/m2). The blood pressure was measured with standardized
sphygmomanometer in mm of Hg. All the measurements were taken
twice before and twice after the experimental period. The pre and
post anthropometric measurements of waist and hip circumference
were measured with the steel tape in cm. The subjects underwent
walking schedule two times in a week for 12 weeks. The 45 minute
sessions of brisk walking were undertaken at an average intensity of
65% to 85% of maximum HR (HRmax; calculated as 220-age).
Results & Discussion: Statistical findings revealed significant
changes from pre test to post test in case of both systolic blood
pressure and diastolic blood pressure in the walking group. Results
also showed significant decrease in their body mass index and
anthropometric measurements i.e. (waist & hip circumference).
Conclusion: It was concluded that twelve weeks brisk walking is
beneficial for lowering of blood pressure, body mass index, and
anthropometric circumference of obese males.
Abstract: Knowledge Discovery of Databases (KDD) is the
process of extracting previously unknown but useful and significant
information from large massive volume of databases. Data Mining is
a stage in the entire process of KDD which applies an algorithm to
extract interesting patterns. Usually, such algorithms generate huge
volume of patterns. These patterns have to be evaluated by using
interestingness measures to reflect the user requirements.
Interestingness is defined in different ways, (i) Objective measures
(ii) Subjective measures. Objective measures such as support and
confidence extract meaningful patterns based on the structure of the
patterns, while subjective measures such as unexpectedness and
novelty reflect the user perspective. In this report, we try to brief the
more widely spread and successful subjective measures and propose
a new subjective measure of interestingness, i.e. shocking.
Abstract: Medical imaging uses the advantage of digital
technology in imaging and teleradiology. In teleradiology systems
large amount of data is acquired, stored and transmitted. A major
technology that may help to solve the problems associated with the
massive data storage and data transfer capacity is data compression
and decompression. There are many methods of image compression
available. They are classified as lossless and lossy compression
methods. In lossy compression method the decompressed image
contains some distortion. Fractal image compression (FIC) is a lossy
compression method. In fractal image compression an image is
coded as a set of contractive transformations in a complete metric
space. The set of contractive transformations is guaranteed to
produce an approximation to the original image. In this paper FIC is
achieved by PIFS using quadtree partitioning. PIFS is applied on
different images like , Ultrasound, CT Scan, Angiogram, X-ray,
Mammograms. In each modality approximately twenty images are
considered and the average values of compression ratio and PSNR
values are arrived. In this method of fractal encoding, the
parameter, tolerance factor Tmax, is varied from 1 to 10, keeping the
other standard parameters constant. For all modalities of images the
compression ratio and Peak Signal to Noise Ratio (PSNR) are
computed and studied. The quality of the decompressed image is
arrived by PSNR values. From the results it is observed that the
compression ratio increases with the tolerance factor and
mammogram has the highest compression ratio. The quality of the
image is not degraded upto an optimum value of tolerance factor,
Tmax, equal to 8, because of the properties of fractal compression.
Abstract: Forming a legal culture among citizens is a
complicated and lengthy process, influencing all spheres of social
life. It includes promoting justice, learning rights and duties, the
introduction of juridical norms and knowledge, and also a process of
developing a system of legal acts and constitutional norms. Currently,
the evaluative and emotional influence of attempts to establish a legal
culture among the citizens of Kazakhstan is limited by real legal
practice. As a result, the values essential to a sound civil society are
absent from the consciousness of the Kazakh people who are thus, in
turn, not able to develop respect for these values. One of the
disadvantages of the modern Kazakh educational system is a
tendency to underrate the actual forces shaping the worldview of
Kazakh youths. The mass-media, which are going through a
personnel crisis, cannot provide society with the legal and political
information necessary to form the sort of legal culture required for a
true civil society.
Abstract: The Internet has become an indispensable part of our lives. Witnessing recent web-based mass collaboration, e.g. Wikipedia, people are questioning whether the Internet has made fundamental changes to the society or whether it is merely a hyperbolic fad. It has long been assumed that collective action for a certain goal yields the problem of free-riding, due to its non-exclusive and non-rival characteristics. Then, thanks to recent technological advances, the on-line space experienced the following changes that enabled it to produce public goods: 1) decrease in the cost of production or coordination 2) externality from networked structure 3) production function which integrates both self-interest and altruism. However, this research doubts the homogeneity of on-line mass collaboration and argues that a more sophisticated and systematical approach is required. The alternative that we suggest is to connect the characteristics of the goal to the motivation. Despite various approaches, previous literature fails to recognize that motivation can be structurally restricted by the characteristic of the goal. First we draw a typology of on-line mass collaboration with 'the extent of expected beneficiary' and 'the existence of externality', and then we examine each combination of motivation using Benkler-s framework. Finally, we explore and connect such typology with its possible dominant participating motivation.
Abstract: Mycophenolic acid “MPA" is a secondary metabolite
of Penicillium bervicompactum with antibiotic and
immunosuppressive properties. In this study, fermentation process
was established for production of mycophenolic acid by Penicillium
bervicompactum MUCL 19011 in shake flask. The maximum MPA
production, product yield and productivity were 1.379 g/L, 18.6 mg/g
glucose and 4.9 mg/L.h respectively. Glucose consumption, biomass
and MPA production profiles were investigated during fermentation
time. It was found that MPA production starts approximately after
180 hours and reaches to a maximum at 280 h. In the next step, the
effects of methionine and acetate concentrations on MPA production
were evaluated. Maximum MPA production, product yield and
productivity (1.763 g/L, 23.8 mg/g glucose and 6.30 mg/L. h
respectively) were obtained with using 2.5 g/L methionine in culture
medium. Further addition of methionine had not more positive effect
on MPA production. Finally, results showed that the addition of
acetate to the culture medium had not any observable effect on MPA
production.
Abstract: The major urban centers are all facing rapid growth is
most often associated with spreading urbanization, social status of the
car has also changed: it has become a commodity of mass
consumption. There are currently about 5 million and 260 cars in
Algeria (2008), this number increases every year 200,000 new cars.
These phenomena induce a demand for greater mobility and a
significant need for transport infrastructure. Faced with these
problems and development of the growing use of the automobile,
central governments and local authorities in charge of urban transport
issues are aware of the need to develop their urban transport systems
but often lack opportunities.
Urban Transport Plans (PDU) were born in reaction to the "culture
of automobile." Their existence in the world the '80s, however, they
had little success before laws on air and rational use of energy in 90
years does not alter substantially their content and make mandatory
their implementation in cities of over 100,000 inhabitants (Abroad)
[1].
The objective of this work is to use the tool and specifically
Geomatics techniques as decision support in the organization and
management of travel while taking into consideration the influence,
which will then translate by National Urban Transport Plan.
Abstract: The present work presents the extraction of copper(II)
from sulphuric acid solutions with Sodium diethyldithiocarbamate
(SDDT), and six different organic diluents: Dichloromethane,
Chloroform, Carbon tetrachloride, Toluene, xylene and Cyclohexane,
were tested. The pair SDDT/Chloroform showed to be the most
selective in removing the copper cations, and hence was considered
throughout the experimental study.
The effects of operating parameters such as the initial concentration
of the extracting agent, the agitation time, the agitation speed and the
acid concentration were considered.
For an initial concentration of Cu (II) of 63 ppm in a 0.5 M sulphuric
acid solution, both with a mass of the extracting agent of 20 mg, an
extraction percentage of about 97.8 % and a distribution coefficient
of 44.42 were obtained, respectively, confirming the performance
of the SDDT-Chloroform pair.
Abstract: Attempts to add fibre and polyphenols (PPs) into
popular beverages present challenges related to the properties of
finished products such as smoothies. Consumer acceptability,
viscosity and phenolic composition of smoothies containing high
levels of fruit fibre (2.5-7.5 g per 300 mL serve) and PPs (250-750
mg per 300 mL serve) were examined. The changes in total
extractable PP, vitamin C content, and colour of selected smoothies
over a storage stability trial (4°C, 14 days) were compared. A set of
acidic aqueous model beverages were prepared to further examine
the effect of two different heat treatments on the stability and
extractability of PPs. Results show that overall consumer
acceptability of high fibre and PP smoothies was low, with average
hedonic scores ranging from 3.9 to 6.4 (on a 1-9 scale). Flavour,
texture and overall acceptability decreased as fibre and polyphenol
contents increased, with fibre content exerting a stronger effect.
Higher fibre content resulted in greater viscosity, with an elevated PP
content increasing viscosity only slightly. The presence of fibre also
aided the stability and extractability of PPs after heating. A reduction
of extractable PPs, vitamin C content and colour intensity of
smoothies was observed after a 14-day storage period at 4°C. Two
heat treatments (75°C for 45 min or 85°C for 1 min) that are
normally used for beverage production, did not cause significant
reduction of total extracted PPs. It is clear that high levels of added
fibre and PPs greatly influence the consumer appeal of smoothies,
suggesting the need to develop novel formulation and processing
methods if a satisfactory functional beverage is to be developed
incorporating these ingredients.
Abstract: World population growth drives food demand, promotes intensification of agriculture, development of new production technologies and varieties more suitable for regional nature conditions. Climate change can affect the length of growing period, biomass and carbon accumulation in winter wheat. The increasing mean air temperature resulting from climate change can reduce the length of growth period of cereals, and without adequate adjustments in growing technologies or varieties, can reduce biomass and carbon accumulation. Deeper understanding and effective measures for monitoring and management of cereal growth process are needed for adaptation to changing climate and technological conditions.
Abstract: The reduction of hexavalent chromium by scrap iron
was investigated in continuous system, using long-term column
experiments, for aqueous Cr(VI) solutions having low buffering
capacities, over the Cr(VI) concentration range of 5 – 40 mg/L. The
results showed that the initial Cr(VI) concentration significantly
affects the reduction capacity of scrap iron. Maximum reduction
capacity of scrap iron was observed at the beginning of the column
experiments; the lower the Cr(VI) concentration, the greater the
experiment duration with maximum scrap iron reduction capacity.
However, due to passivation of active surface, scrap iron reduction
capacity continuously decreased in time, especially after Cr(VI)
breakthrough. The experimental results showed that highest
reduction capacity recorded until Cr(VI) breakthrough was 22.8 mg
Cr(VI)/g scrap iron, at CI = 5 mg/L, and decreased with increasing
Cr(VI) concentration. In order to assure total reduction of greater
Cr(VI) concentrations for a longer period of time, either the mass of
scrap iron filling, or the hydraulic retention time should be increased.
Abstract: The study site was located in Ratchaburi Province,
Thailand. Four experimental plots in dry dipterocarp forest (DDF)
and four plots in mixed deciduous forest (MDF) were set up to
estimate the above-ground biomass of tree, sapling and bamboo. The
allometry equations were used to investigate above-ground biomass
of these vegetation. Seedling and other understory were determined
using direct harvesting method. Carbon storage in above-ground
biomass was calculated based on IPCC 2006.
The results showed that the above-ground biomass of DDF at
20-40% slope,