Abstract: This paper features the trajectory planning design of a indigenously developed 4-Axis SCARA robot which is used for doing successful robotic manipulation task in the laboratory. Once, a trajectory is being designed and given as input to the robot, the robot's gripper tip moves along that specified trajectory. Trajectories have to be designed in the work space only. The main idea of this paper is to design a continuous path trajectory model for the indigenously developed SCARA robot arm during its maneuvering from one point to another point (during pick and place operations) in a workspace avoiding all the obstacles in its path of motion.
Abstract: This paper presents a resonant-based read-out circuit for capacitive pressure sensors. The proposed read-out circuit consists of an LC oscillator and a counter. The circuit detects the capacitance changes of a capacitive pressure sensor by means of frequency shifts from its nominal operation frequency. The proposed circuit is designed in 0.18 m CMOS with an estimated power consumption of 43.1mW. Simulation results show that the circuit has a capacitive resolution of 8.06kHz/fF, which enables it for high resolution pressure detection.
Abstract: In this study we present the effect of elevated
temperatures from 300K to 400K on the electrical properties of
copper Phthalocyanine (CuPc) based organic field effect transistors
(OFET). Thin films of organic semiconductor CuPc (40nm) and
semitransparent Al (20nm) were deposited in sequence, by vacuum
evaporation on a glass substrate with previously deposited Ag source
and drain electrodes with a gap of 40 μm. Under resistive mode of
operation, where gate was suspended it was observed that drain
current of this organic field effect transistor (OFET) show an
increase with temperature. While in grounded gate condition metal
(aluminum) – semiconductor (Copper Phthalocyanine) Schottky
junction dominated the output characteristics and device showed
switching effect from low to high conduction states like Zener diode
at higher bias voltages. This threshold voltage for switching effect
has been found to be inversely proportional to temperature and shows
an abrupt decrease after knee temperature of 360K. Change in
dynamic resistance (Rd = dV/dI) with respect to temperature was
observed to be -1%/K.
Abstract: The radius-of-curvature (ROC) defines the degree of
curvature along the centerline of a roadway whereby a travelling
vehicle must follow. Roadway designs must encompass ROC in
mitigating the cost of earthwork associated with construction while
also allowing vehicles to travel at maximum allowable design speeds.
Thus, a road will tend to follow natural topography where possible,
but curvature must also be optimized to permit fast, but safe vehicle
speeds. The more severe the curvature of the road, the slower the
permissible vehicle speed. For route planning, whether for urban
settings, emergency operations, or even parcel delivery, ROC is a
necessary attribute of road arcs for computing travel time.
It is extremely rare for a geo-spatial database to contain ROC. This
paper will present a procedure and mathematical algorithm to
calculate and assign ROC to a segment pair and/or polyline.
Abstract: Rotor Flux based Model Reference Adaptive System
(RF-MRAS) is the most popularly used conventional speed
estimation scheme for sensor-less IM drives. In this scheme, the
voltage model equations are used for the reference model. This
encounters major drawbacks at low frequencies/speed which leads to
the poor performance of RF-MRAS. Replacing the reference model
using Neural Network (NN) based flux estimator provides an
alternate solution and addresses such drawbacks. This paper
identifies an NN based flux estimator using Single Neuron Cascaded
(SNC) Architecture. The proposed SNC-NN model replaces the
conventional voltage model in RF-MRAS to form a novel MRAS
scheme named as SNC-NN-MRAS. Through simulation the proposed
SNC-NN-MRAS is shown to be promising in terms of all major
issues and robustness to parameter variation. The suitability of the
proposed SNC-NN-MRAS based speed estimator and its advantages
over RF-MRAS for sensor-less induction motor drives is
comprehensively presented through extensive simulations.
Abstract: An effective approach for extracting document images from a noisy background is introduced. The entire scheme is divided into three sub- stechniques – the initial preprocessing operations for noise cluster tightening, introduction of a new thresholding method by maximizing the ratio of stan- dard deviations of the combined effect on the image to the sum of weighted classes and finally the image restoration phase by image binarization utiliz- ing the proposed optimum threshold level. The proposed method is found to be efficient compared to the existing schemes in terms of computational complexity as well as speed with better noise rejection.
Abstract: In order to better understand the performance of
screen channel liquid acquisition devices (LADs) in liquid oxygen (LOX), a computational fluid dynamics (CFD) simulation of LOX passing through a LAD screen channel was conducted. In the
simulation, the screen is taken as a 'porous jump' where the pressure
drop across the screen depends on the incoming velocity and is formulated by Δp = Av + Bv2
. The CFD simulation reveals the importance of the pressure losses due to the flow entering from
across the screen and impacting and merging with the channel flow
and the vortices in the channel to the cumulative flow resistance. In fact, both the flow resistance of flows impact and mergence and the
resistance created by vortices are much larger than the friction and dynamic pressure losses in the channel and are comparable to the
flow resistance across the screen. Therefore, these resistances in the
channel must be considered as part of the evaluation for the LAD
channel performance. For proper operation of a LAD in LOX these resistances must be less than the bubble point pressure for the screen
channel in LOX. The simulation also presents the pressure and velocity distributions within the LAD screen channel, expanding the understanding of the fluid flow characteristics within the channel.
Abstract: Attack graph is an integral part of modeling the
overview of network security. System administrators use attack graphs to determine how vulnerable their systems are and to determine
what security measures to deploy to defend their systems. Previous methods on AGG(attack graphs generation) are aiming at
the whole network, which makes the process of AGG complex and
non-scalable. In this paper, we propose a new approach which is
simple and scalable to AGG by decomposing the whole network into atomic domains. Each atomic domain represents a host with a specific privilege. Then the process for AGG is achieved by communications
among all the atomic domains. Our approach simplifies the process
of design for the whole network, and can gives the attack graphs including each attack path for each host, and when the network changes we just carry on the operations of corresponding atomic
domains which makes the process of AGG scalable.
Abstract: Ants are fascinating creatures that demonstrate the
ability to find food and bring it back to their nest. Their ability as a
colony, to find paths to food sources has inspired the development of
algorithms known as Ant Colony Systems (ACS). The principle of
cooperation forms the backbone of such algorithms, commonly used
to find solutions to problems such as the Traveling Salesman
Problem (TSP). Ants communicate to each other through chemical
substances called pheromones. Modeling individual ants- ability to
manipulate this substance can help an ACS find the best solution.
This paper introduces a Dynamic Ant Colony System with threelevel
updates (DACS3) that enhance an existing ACS. Experiments
were conducted to observe single ant behavior in a colony of
Malaysian House Red Ants. Such behavior was incorporated into the
DACS3 algorithm. We benchmark the performance of DACS3 versus
DACS on TSP instances ranging from 14 to 100 cities. The result
shows that the DACS3 algorithm can achieve shorter distance in
most cases and also performs considerably faster than DACS.
Abstract: Recently, most digital systems are designed as GALS (Globally Asynchronous Locally Synchronous) systems. Several architectures have been proposed as bus architectures for a GALS system : shared bus, segmented bus, ring bus, and so on. In this study, we propose a ring segmented bus architecture which is a combination of segmented bus and ring bus architecture with the aim of throughput enhancement. In a segmented bus architecture, segments are connected in series. By connecting the segments at the end of the bus and constructing the ring bus, it becomes possible to allocate a channel of the bus bidirectionally. The bus channel is allocated to the shortest path between segments. We consider a metastable operation caused by asynchronous communication between segments and a burst transfer between segments. According to the result of simulation, it is shown that the GALS system designed by the proposed method has the desired operations.
Abstract: Slag sample from copper smelting operation in a
water jacket furnace from DRC plant was used. The study intends to
determine the effect of cooling in the extraction of base metals. The
cooling methods investigated were water quenching, air cooling and
furnace cooling. The latter cooling ways were compared to the
original as received slag. It was observed that, the cooling rate of the
slag affected the leaching of base metals as it changed the phase
distribution in the slag and the base metals distribution within the
phases. It was also found that fast cooling of slag prevented
crystallization and produced an amorphous phase that encloses the
base metals. The amorphous slags from the slag dumps were more
leachable in acidic medium (HNO3) which leached 46%Cu, 95% Co,
85% Zn, 92% Pb and 79% Fe with no selectivity at pH0, than in
basic medium (NH4OH). The leachability was vice versa for the
modified slags by quenching in water which leached 89%Cu with a
high selectivity as metal extractions are less than 1% for Co, Zn, Pb
and Fe at ambient temperature and pH12. For the crystallized slags,
leaching of base metals increased with the increase of temperature
from ambient temperature to 60°C and decreased at the higher
temperature of 80°C due to the evaporation of the ammonia solution
used for basic leaching, the total amounts of base metals that were
leached in slow cooled slags were very low compared to the
quenched slag samples.
Abstract: We present a hardware oriented method for real-time
measurements of object-s position in video. The targeted application
area is light spots used as references for robotic navigation. Different
algorithms for dynamic thresholding are explored in combination
with component labeling and Center Of Gravity (COG) for highest
possible precision versus Signal-to-Noise Ratio (SNR). This method
was developed with a low hardware cost in focus having only one
convolution operation required for preprocessing of data.
Abstract: A robust still image face localization algorithm
capable of operating in an unconstrained visual environment is
proposed. First, construction of a robust skin classifier within a
shifted HSV color space is described. Then various filtering
operations are performed to better isolate face candidates and
mitigate the effect of substantial non-skin regions. Finally, a novel
Bhattacharyya-based face detection algorithm is used to compare
candidate regions of interest with a unique illumination-dependent
face model probability distribution function approximation.
Experimental results show a 90% face detection success rate despite
the demands of the visually noisy environment.
Abstract: OLAP uses multidimensional structures, to provide
access to data for analysis. Traditionally, OLAP operations are more
focused on retrieving data from a single data mart. An exception is
the drill across operator. This, however, is restricted to retrieving
facts on common dimensions of the multiple data marts. Our concern
is to define further operations while retrieving data from multiple
data marts. Towards this, we have defined six operations which
coalesce data marts. While doing so we consider the common as well
as the non-common dimensions of the data marts.
Abstract: This paper considers the benefits gained by using an
efficient quality of service management such as DiffServ technique to
improve the performance of military communications. Low delay and
no blockage must be achieved especially for real time tactical data.
All traffic flows generated by different applications do not need same
bandwidth, same latency, same error ratio and this scalable technique
of packet management based on priority levels is analysed. End to
end architectures supporting various traffic flows and including lowbandwidth
and high-delay HF or SHF military links as well as
unprotected Internet sub domains are studied. A tuning of Diffserv
parameters is proposed in accordance with different loads of various
traffic and different operational situations.
Abstract: Soft set theory was initiated by Molodtsov in 1999. In the past years, this theory had been applied to many branches of mathematics, information science and computer science. In 2003, Maji et al. introduced some operations of soft sets and gave some operational rules. Recently, some of these operational rules are pointed out to be not true. Furthermore, Ali et al., in their paper, introduced and discussed some new operations of soft sets. In this paper, we further investigate these operational rules given by Maji et al. and Ali et al.. We obtain some sufficient-necessary conditions such that corresponding operational rules hold and give correct forms for some operational rules. These results will be help for us to use rightly operational rules of soft sets in research and application of soft set theory.
Abstract: A new design approach for three-stage operational
amplifiers (op-amps) is proposed. It allows to actually implement a
symmetrical push-pull class-AB amplifier output stage for wellestablished
three-stage amplifiers using a feedforward
transconductance stage. Compared with the conventional design
practice, the proposed approach leads to a significant
improvement of the symmetry between the positive and the
negative op-amp step response, resulting in similar values of the
positive/negative settling time. The new approach proves to be very
useful in order to fully exploit the potentiality allowed by the op-amp
in terms of speed performances. Design examples in a commercial
0.35-μm CMOS prove the effectiveness of theproposed strategy.
Abstract: Islamic institutions in Malaysia play a variety of
socioeconomic roles such as poverty alleviation. To perform this role,
these institutions face a major task in identifying the poverty group.
Most of these institutions measure and operationalize poverty from
the monetary perspective using variables such as income, expenditure
or consumption. In practice, most Islamic institutions in Malaysia use
the monetary approach in measuring poverty through the
conventional Poverty Line Income (PLI) method and recently, the
had al kifayah (HAK) method using total necessities of a household
from an Islamic perspective. The objective of this paper is to present
the PLI and also the HAK method. This micro-data study would
highlight the similarities and differences of both the methods.A
survey aided by a structured questionnaire was carried out on 260
selected head of households in the state of Selangor. The paper
highlights several demographic factors that are associated with the
three monetary indicators in the study, namely income, PLI and
HAK. In addition, the study found that these monetary variables are
significantly related with each other.
Abstract: In this study, a comparison of two control methods,
Proportional Control (PC) and Fuzzy Logic Control (FLC), which
have been used to develop an ideal thermoelectric renal hypothermia
system in order to use in renal surgery, has been carried out. Since
the most important issues in long-lasting parenchymatous renal
surgery are to provide an operation medium free of blood and to
prevent renal dysfunction in the postoperative period, control of the
temperature has become very important in renal surgery. The final
product is seriously affected from the changes in temperature,
therefore, it is necessary to reach some desired temperature points
quickly and avoid large overshoot. PIC16F877 microcontroller has
been used as controller for both of these two methods. Each control
method can simply ensure extra renal hypothermia in the targeted
way. But investigation of advantages and disadvantages of every
control method to each other is aimed and carried out by the
experimental implementations. Shortly, investigation of the most
appropriate method to use for development of system and that can be
applied to people safely in the future, has been performed. In this
sense, experimental results show that fuzzy logic control gives out
more reliable responses and efficient performance.
Abstract: Natural language processing systems pose a unique
challenge for software architectural design as system complexity has
increased continually and systems cannot be easily constructed from
loosely coupled modules. Lexical, syntactic, semantic, and pragmatic
aspects of linguistic information are tightly coupled in a manner that
requires separation of concerns in a special way in design,
implementation and maintenance. An aspect oriented software
architecture is proposed in this paper after critically reviewing
relevant architectural issues. For the purpose of this paper, the
syntactic aspect is characterized by an augmented context-free
grammar. The semantic aspect is composed of multiple perspectives
including denotational, operational, axiomatic and case frame
approaches. Case frame semantics matured in India from deep
thematic analysis. It is argued that lexical, syntactic, semantic and
pragmatic aspects work together in a mutually dependent way and
their synergy is best represented in the aspect oriented approach. The
software architecture is presented with an augmented Unified
Modeling Language.