Abstract: The successful use of CDMA technology is based on
the construction of large families of encoding sequences with good
correlation properties. This paper discusses PN sequence generation
based on Residue Arithmetic with an effort to improve the performance
of existing interference-limited CDMA technology for mobile
cellular systems. All spreading codes with residual number system
proposed earlier did not consider external interferences, multipath
propagation, Doppler effect etc. In literature the use of residual
arithmetic in DS-CDMA was restricted to encoding of already spread
sequence; where spreading of sequence is done by some existing
techniques. The novelty of this paper is the use of residual number
system in generation of the PN sequences which is used to spread
the message signal. The significance of cross-correlation factor in
alleviating multi-access interference is also discussed. The RNS based
PN sequence has superior performance than most of the existing
codes that are widely used in DS-CDMA applications. Simulation
results suggest that the performance of the proposed system is
superior to many existing systems.
Abstract: The present study conducted experimental investigation on combustion and emission characteristics of compression ignition engine using diesel as pilot fuel and methane, hydrogen and methane/hydrogen mixture as gaseous fuels at 1800 rev min-1. The effect of gaseous fuel on peak cylinder pressure and heat release is modest at low to medium loads. At high load, the high combustion temperature and high quantity of pilot fuel contribute to better combustion efficiency for all kinds of gaseous fuels and increases the peak cylinder pressure. Enrichment of hydrogen in methane gradually increases the peak cylinder pressure. The brake thermal efficiency increases with higher hydrogen fraction at lower loads. Hydrogen addition in methane contributed to a proportional reduction of CO/CO2/HC emission without penalty of NOx. For particulate emission, methane and hydrogen, could both suppress the particle emission. 30% hydrogen fraction in methane is observed to be best in reducing the particulate emission.
Abstract: Finger spelling is an art of communicating by signs
made with fingers, and has been introduced into sign language to serve
as a bridge between the sign language and the verbal language.
Previous approaches to finger spelling recognition are classified into
two categories: glove-based and vision-based approaches. The
glove-based approach is simpler and more accurate recognizing work
of hand posture than vision-based, yet the interfaces require the user to
wear a cumbersome and carry a load of cables that connected the
device to a computer. In contrast, the vision-based approaches provide
an attractive alternative to the cumbersome interface, and promise
more natural and unobtrusive human-computer interaction. The
vision-based approaches generally consist of two steps: hand
extraction and recognition, and two steps are processed independently.
This paper proposes real-time vision-based Korean finger spelling
recognition system by integrating hand extraction into recognition.
First, we tentatively detect a hand region using CAMShift algorithm.
Then fill factor and aspect ratio estimated by width and height
estimated by CAMShift are used to choose candidate from database,
which can reduce the number of matching in recognition step. To
recognize the finger spelling, we use DTW(dynamic time warping)
based on modified chain codes, to be robust to scale and orientation
variations. In this procedure, since accurate hand regions, without
holes and noises, should be extracted to improve the precision, we use
graph cuts algorithm that globally minimize the energy function
elegantly expressed by Markov random fields (MRFs). In the
experiments, the computational times are less than 130ms, and the
times are not related to the number of templates of finger spellings in
database, as candidate templates are selected in extraction step.
Abstract: The knowledge of the nature of loading is very
important in order to hold account on the total behavior such as
vibration, shock, fatigue, etc. Fatigue present 90% of failure when
loadings fatigues are very complex. In this paper a study of double
through crack at hole for plate subjected to fatigue loading is
presented. Various modes loading are studied where the applied load
is the same one. The fatigue life is given where the effect of stress
ratio is highlighted. This work is conducted on aluminum alloy 2024
T351 used for much aerospace and aeronautics applications. The
fatigue crack growth behavior with constant amplitude is studied
using the AFGROW code when Forman model is applied. The
fatigue crack growth rate and fatigue life for different loading modes
are compared with variation of others geometrical parameter such as
thickness and dimensions of notch hole.
Abstract: The voltage/current characteristics and the effect of
NO2 gas on the electrical conductivity of a PbPc gas sensor array is
investigated. The gas sensor is manufactured using vacuum
deposition of gold electrodes on sapphire substrate with the leadphathalocyanine
vacuum sublimed on the top of the gold electrodes.
Two versions of the PbPc gas sensor array are investigated. The
tested types differ in the gap sizes between the deposited gold
electrodes. The sensors are tested at different temperatures to account
for conductivity changes as the molecular adsorption/desorption rate
is affected by heat. The obtained results found to be encouraging as
the sensors shoed stability and sensitivity towards low concentration
of applied NO2 gas.
Abstract: In this paper we present high performance
dynamically allocated multi-queue (DAMQ) buffer schemes for fault
tolerance systems on chip applications that require an interconnection
network. Two virtual channels shared the same buffer space. Fault
tolerant mechanisms for interconnection networks are becoming a
critical design issue for large massively parallel computers. It is also
important to high performance SoCs as the system complexity keeps
increasing rapidly. On the message switching layer, we make
improvement to boost system performance when there are faults
involved in the components communication. The proposed scheme is
when a node or a physical channel is deemed as faulty, the previous
hop node will terminate the buffer occupancy of messages destined
to the failed link. The buffer usage decisions are made at switching
layer without interactions with higher abstract layer, thus buffer
space will be released to messages destined to other healthy nodes
quickly. Therefore, the buffer space will be efficiently used in case
fault occurs at some nodes.
Abstract: We present linear codes over finite commutative rings
which are not necessarily Frobenius. We treat the notion of syndrome
decoding by using Pontrjagin duality. We also give a version of Delsarte-s
theorem over rings relating trace codes and subring subcodes.
Abstract: Hydrodesulfurization (HDS) of dibenzothiophene
(DBT) in a high pressure batch reactor was done at 320 °C on
CoMoS/Al2O3-B2O3 (4, 10, and 16 wt. % of Boria) using nhexadecane
as solvent, dimethyldisulfide (DMDS) in tetradecane as
sulfur agent, and stirring at 1000 rpm. The effects of boria were
investigated by using X-ray diffraction (XRD), Temperature
programmed desorption (TPD) of ammonia, and Brunauer-Emmet-
Teller (BET) experiments. The results showed that the catalyst
prepared with low boria content (4 wt. %) had HDS activity (in
pseudo first order kinetic constant basis) value ~1.45 times higher to
that of CoMoS/Al2O3 catalyst.
Abstract: This paper shows the results of empirical research. It
presents experiences of Polish companies from the Podkarpackie
voivodeship connected with implementing EMS according to the
requirements of the ISO 14001 international standard. The incentives
to introduce and certify organizational eco-innovation, which formal
EMSs are treated as, are presented in this paper.
Abstract: Model-checking tools such as Symbolic Model Verifier
(SMV) and NuSMV are available for checking hardware designs.
These tools can automatically check the formal legitimacy of a
design. However, NuSMV is too low level for describing a complete
hardware design. It is therefore necessary to translate the system
definition, as designed in a language such as Verilog or VHDL, into
a language such as NuSMV for validation. In this paper, we present
a meta hardware description language, Melasy, that contains a code
generator for existing hardware description languages (HDLs) and
languages for model checking that solve this problem.
Abstract: In aerospace applications, interactions of airflow with
aircraft structures can result in undesirable structural deformations.
This structural deformation in turn, can be predicted if the natural
modes of the structure are known. This can be achieved through
conventional modal testing that requires a known excitation force in
order to extract these dynamic properties. This technique can be
experimentally complex because of the need for artificial excitation
and it is also does not represent actual operational condition. The
current work presents part of research work that address the practical
implementation of operational modal analysis (OMA) applied to a
cantilevered hybrid composite plate employing single contactless
sensing system via laser vibrometer. OMA technique extracts the
modal parameters based only on the measurements of the dynamic
response. The OMA results were verified with impact hammer modal
testing and good agreement was obtained.
Abstract: The mixing of pollutions and sediments in near shore regions of natural water bodies depends heavily on the characteristics such as the strength and frequency of flow instability. In the present paper, the instability of natural convection induced by absorption of solar radiation in littoral regions is considered. Spectral analysis is conducted on the quasi-steady state flow to reveal the power and frequency modes of the instability at various positions. Results indicate that the power of instability, the number of frequency modes, the prominence of higher frequency modes, and the highest frequency mode increase with the offshore distance and/or Rayleigh number. Harmonic modes are present at relatively low Rayleigh numbers. For a given offshore distance, the position with the strongest power of instability is located adjacent to the sloping bottom while the frequency modes are the same over the local depth. As the Rayleigh number increases, the unstable region extends toward the shore.
Abstract: We propose a reduced-ordermodel for the instantaneous
hydrodynamic force on a cylinder. The model consists of a system of
two ordinary differential equations (ODEs), which can be integrated
in time to yield very accurate histories of the resultant force and
its direction. In contrast to several existing models, the proposed
model considers the actual (total) hydrodynamic force rather than its
perpendicular or parallel projection (the lift and drag), and captures
the complete force rather than the oscillatory part only. We study
and provide descriptions of the relationship between the model
parameters, evaluated utilizing results from numerical simulations,
and the Reynolds number so that the model can be used at any
arbitrary value within the considered range of 100 to 500 to provide
accurate representation of the force without the need to perform timeconsuming
simulations and solving the partial differential equations
(PDEs) governing the flow field.
Abstract: Sensor network applications are often data centric and
involve collecting data from a set of sensor nodes to be delivered
to various consumers. Typically, nodes in a sensor network are
resource-constrained, and hence the algorithms operating in these
networks must be efficient. There may be several algorithms available
implementing the same service, and efficient considerations may
require a sensor application to choose the best suited algorithm. In
this paper, we present a systematic evaluation of a set of algorithms
implementing the data gathering service. We propose a modular
infrastructure for implementing such algorithms in TOSSIM with
separate configurable modules for various tasks such as interest
propagation, data propagation, aggregation, and path maintenance.
By appropriately configuring these modules, we propose a number
of data gathering algorithms, each of which incorporates a different
set of heuristics for optimizing performance. We have performed
comprehensive experiments to evaluate the effectiveness of these
heuristics, and we present results from our experimentation efforts.
Abstract: Optical burst switching (OBS) has been proposed to
realize the next generation Internet based on the wavelength division
multiplexing (WDM) network technologies. In the OBS, the burst
contention is one of the major problems. The deflection routing has
been designed for resolving the problem. However, the deflection
routing becomes difficult to prevent from the burst contentions as the
network load becomes high. In this paper, we introduce a flow rate
control methods to reduce burst contentions. We propose new flow
rate control methods based on the leaky bucket algorithm and
deflection routing, i.e. separate leaky bucket deflection method, and
dynamic leaky bucket deflection method. In proposed methods, edge
nodes which generate data bursts carry out the flow rate control
protocols. In order to verify the effectiveness of the flow rate control in
OBS networks, we show that the proposed methods improve the
network utilization and reduce the burst loss probability through
computer simulations.
Abstract: This work presents the mixed-mode II/III prestressed split-cantilever beam specimen for the fracture testing of composite materials. In accordance with the concept of prestressed composite beams one of the two fracture modes is provided by the prestressed state of the specimen, and the other one is increased up to fracture initiation by using a testing machine. The novel beam-like specimen is able to provide any combination of the mode-II and mode-III energy release rates. A simple closed-form solution is developed using beam theory as a data reduction scheme and for the calculation of the energy release rates in the new configuration. The applicability and the limitations of the novel fracture mechanical test are demonstrated using unidirectional glass/polyester composite specimens. If only crack propagation onset is involved then the mixed-mode beam specimen can be used to obtain the fracture criterion of transparent composite materials in the GII - GIII plane in a relatively simple way.
Abstract: Human computer interaction has progressed
considerably from the traditional modes of interaction. Vision based
interfaces are a revolutionary technology, allowing interaction
through human actions, gestures. Researchers have developed
numerous accurate techniques, however, with an exception to few
these techniques are not evaluated using standard HCI techniques. In
this paper we present a comprehensive framework to address this
issue. Our evaluation of a computer vision application shows that in
addition to the accuracy, it is vital to address human factors
Abstract: This article presents the results of researchrelated to the assessment protocol weightedcumulative expected transmission time (WCETT)applied to cognitive radio networks.The development work was based on researchdone by different authors, we simulated a network,which communicates wirelessly, using a licensedchannel, through which other nodes are notlicensed, try to transmit during a given time nodeuntil the station's owner begins its transmission.
Abstract: Wireless sensor networks can be used to measure and monitor many challenging problems and typically involve in monitoring, tracking and controlling areas such as battlefield monitoring, object tracking, habitat monitoring and home sentry systems. However, wireless sensor networks pose unique security challenges including forgery of sensor data, eavesdropping, denial of service attacks, and the physical compromise of sensor nodes. Node in a sensor networks may be vanished due to power exhaustion or malicious attacks. To expand the life span of the sensor network, a new node deployment is needed. In military scenarios, intruder may directly organize malicious nodes or manipulate existing nodes to set up malicious new nodes through many kinds of attacks. To avoid malicious nodes from joining the sensor network, a security is required in the design of sensor network protocols. In this paper, we proposed a security framework to provide a complete security solution against the known attacks in wireless sensor networks. Our framework accomplishes node authentication for new nodes with recognition of a malicious node. When deployed as a framework, a high degree of security is reachable compared with the conventional sensor network security solutions. A proposed framework can protect against most of the notorious attacks in sensor networks, and attain better computation and communication performance. This is different from conventional authentication methods based on the node identity. It includes identity of nodes and the node security time stamp into the authentication procedure. Hence security protocols not only see the identity of each node but also distinguish between new nodes and old nodes.
Abstract: The effect of thermally induced stress on the modal
properties of highly elliptical core optical fibers is studied in this
work using a finite element method. The stress analysis is carried out
and anisotropic refractive index change is calculated using both the
conventional plane strain approximation and the generalized plane
strain approach. After considering the stress optical effect, the modal
analysis of the fiber is performed to obtain the solutions of
fundamental and higher order modes. The modal effective index,
modal birefringence, group effective index, group birefringence, and
dispersion of different modes of the fiber are presented. For
propagation properties, it can be seen that the results depend much on
the approach of stress analysis.