Abstract: A parametric study on circular thin-walled pipes
subjected to pure bending is performed. Both straight and curved
pipes are considered. Ratio D/t, initial pipe curvature and internal
pressure are the parameters varying in the analyses. The study is
mainly FEA-based.
It is found that negative curvatures (opposite to bending moment)
considerably increase stiffness and buckling limit of the pipe when no
internal pressure is acting and, similarly, positive curvatures decrease
the stiffness and buckling limit. For internal pressurised pipes the
effects of initial pipe curvature are less relevant. Results show that
this phenomenon is in relationship with the cross-section deformation
due to bending moment, which undergoes relevant ovalisation for no
pressurised pipes and little ovalisation for pressurised pipes.
Abstract: Recent research in neural networks science and
neuroscience for modeling complex time series data and statistical
learning has focused mostly on learning from high input space and
signals. Local linear models are a strong choice for modeling local
nonlinearity in data series. Locally weighted projection regression is
a flexible and powerful algorithm for nonlinear approximation in
high dimensional signal spaces. In this paper, different learning
scenario of one and two dimensional data series with different
distributions are investigated for simulation and further noise is
inputted to data distribution for making different disordered
distribution in time series data and for evaluation of algorithm in
locality prediction of nonlinearity. Then, the performance of this
algorithm is simulated and also when the distribution of data is high
or when the number of data is less the sensitivity of this approach to
data distribution and influence of important parameter of local
validity in this algorithm with different data distribution is explained.
Abstract: The main objective of this paper is study the influence
of carbon nano-tubes fibers and nano silica fibers on the
characteristic compressive strength and flexural strength on concrete
and cement mortar. Twelve tested specimens were tested with square
section its dimensions (4040 160) mm, divided into four groups.
The first and second group studied the effect of carbon nano-tubes
(CNTs) fibers with different percentage equal to 0.0, 0.11%, 0.22%,
and 0.33% by weight of cement and effect of nano-silica (nS) fibers
with different percentages equal to 0.0, 1.0%, 2.0%, and 3.0% by
weight of cement on the cement mortar. The third and fourth groups
studied the effect of CNTs fiber with different percentage equal to
0.0%, 0.11%, and 0.22% by weight of cement, and effect of nS fibers
with different percentages were equal to 0.0%, 1.0%, and 2.0% by
weight of cement on the concrete. The compressive strength and
flexural strength at 7, 28, and 90 days is determined. From analysis of
tested results concluded that the nano-fibers is more effective when
used with cement mortar more than used with concrete because of
increasing the surface area, decreasing the pore and the collection of
nano-fibers. And also by adding nano-fibers the improvement of
flexural strength of concrete and cement mortar is more than
improvement of compressive strength.
Abstract: In this study, composites were fabricated from oil
palm empty fruit bunch fiber and poly(lactic) acid by extrusion
followed by injection moulding. Surface of the fiber was pre-treated
by ultrasound in an alkali medium and treatment efficiency was
investigated by scanning electron microscopy (SEM) analysis and
Fourier transforms infrared spectrometer (FTIR). Effect of fiber
treatment on composite was characterized by tensile strength (TS),
tensile modulus (TM) and impact strength (IS). Furthermore,
biostrong impact modifier was incorporated into the treated fiber
composite to improve its impact properties. Mechanical testing
showed an improvement of up to 23.5% and 33.6% respectively for
TS and TM of treated fiber composite above untreated fiber
composite. On the other hand incorporation of impact modifier led to
enhancement of about 20% above the initial IS of the treated fiber
composite.
Abstract: The current study investigated the influence of milling
time and ball-to-powder (BPR) weight ratio on the microstructural
constituents and mechanical properties of bulk nanocrystalline Al;
Al-10%Cu; and Al-10%Cu-5%Ti alloys. Powder consolidation was
carried out using a high frequency induction heat sintering where the
processed metal powders were sintered into a dense and strong bulk
material. The powders and the bulk samples were characterized using
XRD and FEGSEM techniques. The mechanical properties were
evaluated at various temperatures of 25°C, 100°C, 200°C, 300°C and
400°C to study the thermal stability of the processed alloys. The
processed bulk nanocrystalline alloys displayed extremely high
hardness values even at elevated temperatures. The Al-10%Cu-5%Ti
alloy displayed the highest hardness values at room and elevated
temperatures which are related to the presence of Ti-containing
phases such as Al3Ti and AlCu2Ti. These phases are thermally stable
and retain the high hardness values at elevated temperatures up to
400ºC.
Abstract: Image or document encryption is needed through egovernment
data base. Really in this paper we introduce two matrices
images, one is the public, and the second is the secret (original). The
analyses of each matrix is achieved using the transformation of
singular values decomposition. So each matrix is transformed or
analyzed to three matrices say row orthogonal basis, column
orthogonal basis, and spectral diagonal basis. Product of the two row
basis is calculated. Similarly the product of the two column basis is
achieved. Finally we transform or save the files of public, row
product and column product. In decryption stage, the original image
is deduced by mutual method of the three public files.
Abstract: In orthopedic surgery there are various situations in
which the surgeon needs to implement methods of cutting and
drilling the bone. With this type of procedure the generated friction
leads to a localized increase in temperature, which may lead to the
bone necrosis. Recognizing the importance of studying this
phenomenon, an experimental evaluation of the temperatures
developed during the procedure of drilling bone has been done.
Additionally the influence of the use of the procedure with / without
additional lubrication during drilling of bone has also been done. The
obtained results are presented and discussed and suggests an
advantage in using additional lubrication as a way to minimize the
appearance of bone tissue necrosis during bone drilling procedures.
Abstract: The present study was undertaken to investigate the
effect of pre-aging and aging parameters (time and temperature) on
the mechanical properties of Al-Mg-Zn (7075) alloys. Ultimate
tensile strength, 0.5% offset yield strength and % elongation
measurements were carried out on specimens prepared from cast and
heat treated 7075 alloys. Aging treatments were carried out for the as
solution treated (SHT) specimens (after quenching in warm water).
The specimens were aged at different conditions; Natural aging was
carried out at room temperature for different periods of time. Double
aging was performed for SHT conditions (pre-aged at different time
and temperature followed by high temperature aging). Ultimate
tensile strength, yield strength and % elongation as a function of
different pre-aging and aging parameters are analyzed to acquire an
understanding of the effects of these variables and their interactions
on the mechanical properties of Be-treated 7075 alloys.
Abstract: In this article is reported a construction and some
properties of the 5iD viewer, the system recording simultaneously
5 views of a given experimental object. Properties of the system
are demonstrated on the analysis of fish schooling behaviour. It
is demonstrated the method of instrument calibration which allows
inclusion of image distortion and it is proposed and partly tested
also the method of distance assessment in the case that only two
opposite cameras are available. Finally, we demonstrate how the state
trajectory of the behaviour of the fish school may be constructed from
the entropy of the system.
Abstract: Parameters of flow are calculated in vaneless diffusers
with relative width 0,014–0,10. Inlet angles of flow and similarity
criteria were varied. There is information on flow separation,
boundary layer development, configuration of streamlines.
Polytrophic efficiency, loss coefficient and recovery coefficient are
used to compare effectiveness of diffusers. The sample of
optimization of narrow diffuser with conical walls is presented. Three
wide diffusers with narrowing walls are compared. The work is made
in the R&D laboratory “Gas dynamics of turbo machines” of the TU
SPb.
Abstract: This paper presents a novel fractal antenna structure
proposed for UWB (Ultra – Wideband) applications. The frequency
band 3.1-10.6GHz released by FCC (Federal Communication
Commission) as the commercial operation of UWB has been chosen
as frequency range for this antenna based on coplanar waveguide
(CPW) feed and circular shapes fulfilled according to fractal
geometry. The proposed antenna is validated and designed by using
an FR4 substrate with overall area of 34x43 mm2. The simulated
results performed by CST-Microwave Studio and compared by ADS
(Advanced Design System) show good matching input impedance
with return loss less than -10dB between 2.9 GHz and 11 GHz.
Abstract: In this paper we consider the rule reduct generation
problem. Rule Reduct Generation (RG) and Modified Rule
Generation (MRG) algorithms, that are used to solve this problem,
are well-known. Alternative to these algorithms, we develop Pruning
Rule Generation (PRG) algorithm. We compare the PRG algorithm
with RG and MRG.
Abstract: Universal modeling method well proven for industrial
compressors was applied for design of the high flow rate supersonic
stage. Results were checked by ANSYS CFX and NUMECA Fine
Turbo calculations. The impeller appeared to be very effective at
transonic flow velocities. Stator elements efficiency is acceptable at
design Mach numbers too. Their loss coefficient versus inlet flow
angle performances correlates well with Universal modeling
prediction. The impeller demonstrates ability of satisfactory operation
at design flow rate. Supersonic flow behavior in the impeller inducer
at the shroud blade to blade surface Φ des deserves additional study.
Abstract: There is an evident trend to elevate pressure ratio of a
single stage of a turbo compressors - axial compressors in particular.
Whilst there was an opinion recently that a pressure ratio 1,9 was a
reasonable limit, later appeared information on successful modeling
tested of stages with pressure ratio up to 2,8. The authors recon that
lack of information on high pressure stages makes actual a study of
rational choice of design parameters before high supersonic flow
problems solving. The computer program of an engineering type was
developed. Below is presented a sample of its application to study
possible parameters of the impeller of the stage with pressure ratio
3,0. Influence of two main design parameters on expected efficiency,
periphery blade speed and flow structure is demonstrated. The results
had lead to choose a variant for further analysis and improvement by
CFD methods.
Abstract: Many organizations bring e-Learning to use as a tool
in their training and human development department. It is getting
more popular because it is easy to access to get knowledge all the
time and also it provides a rich content, which can develop the
employees’ skill efficiently. This study is focused on the factors that
affect using e-Learning efficiently, so it will make job satisfaction
increasing. The questionnaires were sent to employees in large
commercial banks, which use e-Learning located in Bangkok, the
results from multiple linear regression analysis showed that
employee’s characteristics, characteristics of e-Learning, learning and
growth have influence on job satisfaction.
Abstract: The continuous decline of petroleum and natural gas
reserves and non linear rise of oil price has brought about a
realisation of the need for a change in our perpetual dependence on
the fossil fuel. A day to day increased consumption of crude and
petroleum products has made a considerable impact on our foreign
exchange reserves. Hence, an alternate resource for the conversion of
energy (both liquid and gas) is essential for the substitution of
conventional fuels. Biomass is the alternate solution for the present
scenario. Biomass can be converted into both liquid as well as
gaseous fuels and other feedstocks for the industries.
Abstract: Vancron 40, a nitrided powder metallurgical tool
Steel, is used in cold work applications where the predominant failure
mechanisms are adhesive wear or galling. Typical applications of
Vancron 40 are among others fine blanking, cold extrusion, deep
drawing and cold work rolls for cluster mills. Vancron 40 positive
results for cold work rolls for cluster mills and as a tool for some
severe metal forming process makes it competitive compared to other
type of work rolls that require higher precision, among others in cold
rolling of thin stainless steel, which required high surface finish
quality. In this project, three roll materials for cold rolling of stainless
steel strip was examined, Vancron 40, Narva 12B (a high-carbon,
high-chromium tool steel alloyed with tungsten) and Supra 3 (a
Chromium-molybdenum tungsten-vanadium alloyed high speed
steel). The purpose of this project was to study the depth profiles of
the ironed stainless steel strips, emergence of galling and to study the
lubrication performance used by steel industries. Laboratory
experiments were conducted to examine scratch of the strip, galling
and surface roughness of the roll materials under severe tribological
conditions. The critical sliding length for onset of galling was
estimated for stainless steel with four different lubricants. Laboratory
experiments result of performance evaluation of resistance capability
of rolls toward adhesive wear under severe conditions for low and
high reductions. Vancron 40 in combination with cold rolling
lubricant gave good surface quality, prevents galling of
metal surfaces and good bearing capacity.
Abstract: This paper introduces novel approaches to partitioning
and mapping in terms of model-based embedded multicore system
engineering and further discusses benefits, industrial relevance and
features in common with existing approaches. In order to assess
and evaluate results, both approaches have been applied to a real
industrial application as well as to various prototypical demonstrative
applications, that have been developed and implemented for
different purposes. Evaluations show, that such applications improve
significantly according to performance, energy efficiency, meeting
timing constraints and covering maintaining issues by using
the AMALTHEA platform and the implemented approaches.
Furthermore, the model-based design provides an open, expandable,
platform independent and scalable exchange format between
OEMs, suppliers and developers on different levels. Our proposed
mechanisms provide meaningful multicore system utilization since
load balancing by means of partitioning and mapping is effectively
performed with regard to the modeled systems including hardware,
software, operating system, scheduling, constraints, configuration and
more data.
Abstract: Many issues about the relationship between auditors in
auditing practices with its stakeholders often heard. It appears in
perspectives of bringing out the variety of phenomena affecting from
the audit practice of greed and not appreciating from the
independency of the audit profession and professional code of ethics.
It becomes a logical consequence in practicing of capitalism in
accounting. The main purpose of this article would like to uncover
the existing auditing practices in Indonesia, especially in Java that
associated with a strong influence of Javanese culture with reluctant
/”shy", politely, "legowo (gratefully accepted)", "ngemong"
(friendly), "not mentholo" (lenient), "tepo seliro" (tolerance),
"ngajeni" (respectful), "acquiescent" and also reveals its relationships
with Non Javanese culture in facing the conflict of interest in
practical of auditing world. The method used by interpretive
approach that emphasizes the role of language, interpret and
understand and see social reality as something other than a label,
name or concept. Global practices in auditing of each country have
particular cultures that affect the standard set by those regulatory
standards results the adaptation of IAS. The majority of parties in
Indonesia is dominated by Javanese racial regulators, so Java culture
is embedded in every audit practices and those conditions in Java
leads auditors in having similar behaviour, sometimes interfere with
standard Java code of conduct must be executed by an auditor.
Auditors who live in Java have the characters of Javanese culture that
is hard to avoid in the audit practice. However, practically, the
auditors still are relevant in their profession.
Abstract: The mechanics of rip currents are complex, involving
interactions between waves, currents, water levels and the bathymetry,
that present particular challenges for numerical models. Here,
the effects of a grid-spacing dependent horizontal mixing on the
wave-current interactions are studied. Near the shore, wave rays
diverge from channels towards bar crests because of refraction by
topography and currents, in a way that depends on the rip current
intensity which is itself modulated by the horizontal mixing. At
low resolution with the grid-spacing dependent horizontal mixing,
the wave motion is the same for both coupling modes because the
wave deviation by the currents is weak. In high resolution case,
however, classical results are found with the stabilizing effect of
the flow by feedback of waves on currents. Lastly, wave-current
interactions and the horizontal mixing strongly affect the intensity
of the three-dimensional rip velocity.