Abstract: This paper presents a new method to detect high impedance faults in radial distribution systems. Magnitudes of third and fifth harmonic components of voltages and currents are used as a feature vector for fault discrimination. The proposed methodology uses a learning vector quantization (LVQ) neural network as a classifier for identifying high impedance arc-type faults. The network learns from the data obtained from simulation of a simple radial system under different fault and system conditions. Compared to a feed-forward neural network, a properly tuned LVQ network gives quicker response.
Abstract: An influence of intranasal combined injection of live
cold-adapted influenza vaccine with chitosan derivatives as adjuvants
on the subpopulation structure of mononuclear leukocytes of mouse
spleen which reflects the orientation of the immune response was
studied. It is found that the inclusion of chitosan preparations
promotes activation of cellular-level of immune response.
Abstract: An effort to find out the smaller size of cuttings for propagation of Morus alba was made in experimental area Department of Forestry, Range Management and Wildlife, University of Agriculture, Faisalabad, Pakistan. Different size of cuttings i.e. 2", 4", 6" and 8" were planted in polythene tubes of 3.5"x7". The effort was also made to compare the performance of cuttings in open air and in polythene low tunnel. Root length, number of root branches, root diameter and root fresh and dry weight were found maximum in two inches cuttings while minimum in four inches cuttings. Root growth was found maximum in open air as compared to under polythene sheet.
Abstract: The antioxidant compounds are needed for the food, beverages, and pharmaceuticals industry. For this purpose, an appropriate method is required to measure the antioxidant properties in various types of samples. Spectrophotometric method usually used has some weaknesses, including the high price, long sample preparation time, and less sensitivity. Among the alternative methods developed to overcome these weaknesses is antioxidant biosensor based on superoxide dismutase (SOD) enzyme. Therefore, this study was carried out to measure the SOD activity originating from Deinococcus radiodurans and to determine its kinetics properties. Carbon paste electrode modified with ferrocene and immobilized SOD exhibited anode and cathode current peak at potential of +400 and +300mv respectively, in both pure SOD and SOD of D. radiodurans. This indicated that the current generated was from superoxide catalytic dismutation reaction by SOD. Optimum conditions for SOD activity was at pH 9 and temperature of 27.50C for D. radiodurans SOD, and pH 11 and temperature of 200C for pure SOD. Dismutation reaction kinetics of superoxide catalyzed by SOD followed the Lineweaver-Burk kinetics with D. radiodurans SOD KMapp value was smaller than pure SOD. The result showed that D. radiodurans SOD had higher enzyme-substrate affinity and specificity than pure SOD. It concluded that D. radiodurans SOD had a great potential as biological recognition component for antioxidant biosensor.
Abstract: Due to dynamic evolution, the ability of a
manufacturing technology to produce a special product is changing.
Therefore, it is essential to monitor the established techniques and
processes to detect whether a company-s production will fit future
circumstances. Concerning the manufacturing technology planning
process, companies must decide when to change to a new technology
for maintaining and increasing competitive advantages. In this
context, the maturity assessment of the focused technologies is
crucial. This article presents an approach for defining the maturity of
a manufacturing technology from a strategic point of view. The
concept is based on the approach of technology readiness level
(TRL) according to NASA (National Aeronautics and Space
Administration), but also includes dynamic changes. Therefore, the
model takes into account the concept of the technology life cycle.
Furthermore, it enables a company to estimate the ideal date for
implementation of a new manufacturing technology.
Abstract: This study investigated the effect of oxygen and
micro-cracking on the flotation of low grade nickel sulphide ore. The
ore treated contained serpentine minerals which have a history of
being difficult to process efficiently. The use of oxygen as a bubbling
gas has been noted to be effective because it increases the pulp
potential. The desired effect of micro cracking the ore is that the
nickel sulphide minerals will become activated and this activation
will render these minerals more susceptible to react with potassium
amyl xanthate collectors, resulting in a higher recovery of nickel and
hinder the recovery of other undesired minerals contained in the ore.
Higher nickel recoveries were obtained when pure oxygen was used
as a bubbling gas rather than the conventional air. Microwave
cracking favored the recovery of nickel.
Abstract: Intelligent systems are required in order to quickly and accurately analyze enormous quantities of data in the Internet environment. In intelligent systems, information extracting processes can be divided into supervised learning and unsupervised learning. This paper investigates intelligent clustering by unsupervised learning. Intelligent clustering is the clustering system which determines the clustering model for data analysis and evaluates results by itself. This system can make a clustering model more rapidly, objectively and accurately than an analyzer. The methodology for the automatic clustering intelligent system is a multi-agent system that comprises a clustering agent and a cluster performance evaluation agent. An agent exchanges information about clusters with another agent and the system determines the optimal cluster number through this information. Experiments using data sets in the UCI Machine Repository are performed in order to prove the validity of the system.
Abstract: In Data mining, Fuzzy clustering algorithms have
demonstrated advantage over crisp clustering algorithms in dealing
with the challenges posed by large collections of vague and uncertain
natural data. This paper reviews concept of fuzzy logic and fuzzy
clustering. The classical fuzzy c-means algorithm is presented and its
limitations are highlighted. Based on the study of the fuzzy c-means
algorithm and its extensions, we propose a modification to the cmeans
algorithm to overcome the limitations of it in calculating the
new cluster centers and in finding the membership values with
natural data. The efficiency of the new modified method is
demonstrated on real data collected for Bhutan-s Gross National
Happiness (GNH) program.
Abstract: Boron minerals are very useful for various industrial
activities, such as glass industry and detergent industry, due to its
mechanical and chemical properties. During the production of boron
compounds, many of these are introduced into the environment in the
form of waste. Boron is also an important micro nutrient for the
plants to vegetate but if it exists in high concentrations, it could have
toxic effects. The maximum boron level in drinking water for human
health is given as 0.3 mg/L in World Health Organization (WHO)
standards. The toxic effects of boron should be noted especially for
dry regions, thus, in recent years, increasing attention has been paid
to remove the boron from waste waters. In this study, boron removal
is implemented by ion exchange process using Amberlite IRA-743
resin. Amberlite IRA-743 resin is a boron specific resin and it
belongs to the polymerizate sorbent group within the aminopolyol
functional group. Batch studies were performed to investigate the
effects of various experimental parameters, such as adsorbent dose,
initial concentration and pH, on the removal of boron. It is found
that, when the adsorbent dose increases removal of boron from the
liquid phase increases. However, an increase in the initial
concentration decreases the removal of boron. The effective pH
values for removal of boron are determined between 8.5 and 9.
Equilibrium isotherms were also analyzed by Langmuir and
Freundlich isotherm models. The Langmuir isotherm is obeyed better
than the Freundlich isotherm.
Abstract: The supported Pd catalysts were analyzed by X-ray
diffraction and X-ray absorption spectroscopy in order to determine
their global and local structure. The average particle size of the
supported Pd catalysts was determined by X-ray diffraction method.
One of the main purposes of the present contribution is to focus on
understanding the specific role of the Pd particle size determined by
X-ray diffraction and that of the support oxide. Based on X-ray
absorption fine structure spectroscopy analysis we consider that the
whole local structure of the investigated samples are distorted
concerning the atomic number but the distances between atoms are
almost the same as for standard Pd sample. Due to the strong
modifications of the Pd cluster local structure, the metal-support
interface may influence the electronic properties of metal clusters
and thus their reactivity for absorption of the reactant molecules.
Abstract: This study investigated the removal efficiency of electrokinetic remediation of copper-contaminated soil at different combinations of enhancement reagents used as anolyte and catholyte. Sodium hydroxide (at 0.1, 0.5, and 1.0 M concentrations) and distilled water were used as anolyte, while lactic acid (at 0.01, 0.1, and 0.5 M concentrations), ammonium citrate (also at 0.01, 0.1, and 0.5 M concentrations) and distilled water were used as catholyte. A continuous voltage application (1.0 VDC/cm) was employed for 240 hours for each experiment. The copper content of the catholyte was determined at the end of the 240-hour period. Optimization was carried out with a Response Surface Methodology - Optimal Design, including F test, and multiple comparison method, to determine which pair of anolyte-catholyte was the most significant for the removal efficiency. "1.0 M NaOH" was found to be the most significant anolyte while it was established that lactic acid was the most significant type of catholyte to be used for the most successful electrokinetic experiments. Concentrations of lactic acid should be at the range of 0.1 M to 0.5 M to achieve maximum percent removal values.
Abstract: In the process of polyethylene extrusion polymer
material similar to powder or granule is under compression, melting
and transmission operation and on base of special form, extrudate has
been produced. Twin-screw extruders are applicable in industries
because of their high capacity. The powder mixing with chemical
additives and melting with thermal and mechanical energy in three
zones (feed, compression and metering zone) and because of gear
pump and screw's pressure, converting to final product in latest plate.
Extruders with twin-screw and short distance between screws are
better than other types because of their high capacity and good
thermal and mechanical stress.
In this paper, process of polyethylene extrusion and various tapes
of extruders are studied. It is necessary to have an exact control on
process to producing high quality products with safe operation and
optimum energy consumption.
The granule size is depending on granulator motor speed. Results
show at constant feed rate a decrease in granule size was found whit
Increase in motor speed. Relationships between HDPE feed rate and
speed of granulator motor, main motor and gear pump are calculated
following as:
x = HDPE feed flow rate, yM = Main motor speed
yM = (-3.6076e-3) x^4+ (0.24597) x^3+ (-5.49003) x^2+ (64.22092)
x+61.66786 (1)
x = HDPE feed flow rate, yG = Gear pump speed
yG = (-2.4996e-3) x^4+ (0.18018) x^3+ (-4.22794) x^2+ (48.45536)
x+18.78880 (2)
x = HDPE feed flow rate, y = Granulator motor speed
10th Degree Polynomial Fit: y = a+bx+cx^2+dx^3... (3)
a = 1.2751, b = 282.4655, c = -165.2098,
d = 48.3106, e = -8.18715, f = 0.84997
g = -0.056094, h = 0.002358, i = -6.11816e-5
j = 8.919726e-7, k = -5.59050e-9
Abstract: In countries with hot climates, air-conditioning forms
a large proportion of annual peak electrical demand, requiring
expansion of power plants to meet the peak demand, which goes
unused most of the time. Use of well-designed cool storage can offset
the peak demand to a large extent. In this study, an air conditioning
system with naturally stratified storage tank was designed,
constructed and tested. A new type of diffuser was designed and used
in this study. Factors that influence the performance of chilled water
storage tanks were investigated. The results indicated that stratified
storage tank consistently stratified well without any physical barrier.
Investigation also showed that storage efficiency decreased with
increasing flow rate due to increased mixing of warm and chilled
water. Diffuser design and layout primarily affected the mixing near
the inlet diffuser and the extent of this mixing had primary influence
on the shape of the thermocline. The heat conduction through tank
walls and through the thermocline caused widening of mixed volume.
Thermal efficiency of stratified storage tanks was as high as 90
percent, which indicates that stratified tanks can effectively be used
as a load management technique.
Abstract: Due to the low heavy metal concentrations, the
bottom ash from a 32 MW municipal district heating plant was
determined to be a potential forest fertilizer as such. However,
additional Ca would be needed, because its Ca concentration of 1.9-
% (d.w.) was lower than the statutory Finnish minimum limit value
of 6.0-% (d.w.) for Ca in forest fertilizer. Due to the elevated As
concentration (53.0 mg/kg; d.w.) in the fly ash from the 32 MW
municipal district heating plant, and Cr concentration (620 mg/kg;
d.w.) in the ash fraction (i.e. mixture of the bottom ash and fly ash)
from the 6 MW municipal district heating plant, which exceed the
limit values of 30 mg/kg (d.w.) and 300 mg/kg (d.w.) for As and Cr,
respectively, these residues are not suitable as forest fertilizers.
Although these ash fractions cannot be used as a forest fertilizer as
such, they can be used for the landscaping of landfills or in industrial
and other areas that are closed to the public. However, an
environmental permit is then needed.
Abstract: In today-s modern world, the number of vehicles is
increasing on the road. This causes more people to choose walking
instead of traveling using vehicles. Thus, proper planning of
pedestrians- paths is important to ensure the safety of pedestrians in a
walking area. Crowd dynamics study the pedestrians- behavior and
modeling pedestrians- movement to ensure safety in their walking paths.
To date, many models have been designed to ease pedestrians-
movement. The Social Force Model is widely used among researchers
as it is simpler and provides better simulation results. We will discuss
the problem regarding the ritual of circumambulating the Ka-aba
(Tawaf) where the entrances to this area are usually congested which
worsens during the Hajj season. We will use the computer simulation
model SimWalk which is based on the Social Force Model to simulate
the movement of pilgrims in the Tawaf area. We will first discuss the
effect of uni and bi-directional flows at the gates. We will then restrict
certain gates to the area as the entrances only and others as exits only.
From the simulations, we will study the effect of the distance of other
entrances from the beginning line and their effects on the duration of
pilgrims circumambulate Ka-aba. We will distribute the pilgrims at the
different entrances evenly so that the congestion at the entrances can be
reduced. We would also discuss the various locations and designs of
barriers at the exits and its effect on the time taken for the pilgrims to
exit the Tawaf area.
Abstract: This paper presents and discusses the numerical simulations of transient laminar natural convection cooling of high Prandtl number fluids in cubical cavities, in which the six walls of the cavity are subjected to a step change in temperature. The effect of the fluid Prandtl number on the heat transfer coefficient is studied for three different fluids (Golden Syrup, Glycerin and Glycerin-water solution 50%). The simulations are performed at two different Rayleigh numbers (5·106 and 5·107) and six different Prandtl numbers (3 · 105 ≥Pr≥ 50). Heat conduction through the cavity glass walls is also considered. The propsed correlations of the averaged heat transfer coefficient (N u) showed that it is dependant on the initial Ra and almost independent on P r. The instantaneous flow patterns, temperature contours and time evolution of volume averaged temperature and heat transfer coefficient are presented and analyzed.
Abstract: Partial coherence between two signals removing the contribution of a periodic, deterministic signal is proposed for evaluating the interrelationship in multivariate systems. The estimator expression was derived and shown to be independent of such periodic signal. Simulations were used for obtaining its critical value, which were found to be the same as those for Gaussian signals, as well as for evaluating the technique. An Illustration with eletroencephalografic (EEG) signals during photic stimulation is also provided. The application of the proposed technique in both simulation and real EEG data indicate that it seems to be very specific in removing the contribution of periodic sources. The estimate independence of the periodic signal may widen partial coherence application to signal analysis, since it could be used together with simple coherence to test for contamination in signals by a common, periodic noise source.
Abstract: The main purpose of this research aimed to create tactile texture designed media for the blind used for extra learning outside classrooms in order to enhance imagination of the blind about Himmapan creatures, furthermore, the main objective of the research focused on improving the visual disabled perception to be equal to normal people. The target group of the research is blinded students studying in The Bangkok school for the blind between grade 4-6 in the second semester of 2011 who are able to read the braille language. The research methodology consisted of the field study and the documentary study related to the blind, tactile texture designed media and Himmapan creatures. 10 pictures of tactile texture designed media were created in the designing process which began after the analysis had conducted based the primary and secondary data. The works had presented to experts in the visual disabled field who evaluated the works. After approval, the works used as prototype to teach the blind. KeywordsBlind, Himmapan Creatures, Tactile Texture.
Abstract: Effective estimation of just noticeable distortion (JND) for images is helpful to increase the efficiency of a compression algorithm in which both the statistical redundancy and the perceptual redundancy should be accurately removed. In this paper, we design a DCT-based model for estimating JND profiles of color images. Based on a mathematical model of measuring the base detection threshold for each DCT coefficient in the color component of color images, the luminance masking adjustment, the contrast masking adjustment, and the cross masking adjustment are utilized for luminance component, and the variance-based masking adjustment based on the coefficient variation in the block is proposed for chrominance components. In order to verify the proposed model, the JND estimator is incorporated into the conventional JPEG coder to improve the compression performance. A subjective and fair viewing test is designed to evaluate the visual quality of the coding image under the specified viewing condition. The simulation results show that the JPEG coder integrated with the proposed DCT-based JND model gives better coding bit rates at visually lossless quality for a variety of color images.
Abstract: This study assessed fish marketing as panacea towards
sustainable agriculture in Ogun State, Nigeria. Multi-stage sampling
technique was used in the selection of 150 fish marketers for this
study. Descriptive statistics were used for the objectives while
Product Pearson Moment Correlation was used to test the hypothesis.
Result of the findings revealed that the mean age of the respondents
was 38.60 years. Majority (93.33%) of the respondents had
acceptable levels of formal education. Many (44.00%) of the
respondents had spent 1-5 years in fish marketing. The average
quantity of fish sold in a day was 94.10kg. However, efficient fish
marketing were hindered by inadequate processing equipment,
storage rooms and ice holding facilities (86.67%). There was a
significant relationship between socio-economic characteristics and
profit realized from fish marketing (p < 0.05). It was recommended
that storage and warehousing facilities should be provided to the fish
marketers in the study area.