Abstract: Cobalt was acid nitric leached from a mixed cobaltcopper
oxide with variable acid concentration. Resulting
experimental data were used to analyze effects of increase in acid
concentration, based on a shrinking core model of the process. The
mathematical simulation demonstrated that the time rate of the
dissolution mechanism is an increasing function of acid
concentration. It was also shown that the magnitude of the acid
concentration effect is time dependent and the increase in acid
concentration is more effective at earlier stage of the dissolution than
at later stage. The remaining process parameters are comprehensively
affected by acid concentration and their interaction is synergetic.
Abstract: Data rate, tolerable bit error rate or frame error rate
and range & coverage are the key performance requirement of a
communication link. In this paper performance of MFSK link is
analyzed in terms of bit error rate, number of errors and total number
of data processed. In the communication link model proposed, which
is implemented using MATLAB block set, an improvement in BER
is observed. Different parameters which effects and enables to keep
BER low in M-ary communication system are also identified.
Abstract: This paper focuses on a critical component of the
situational awareness (SA), the control of autonomous vertical flight for tactical unmanned aerial vehicle (TUAV). With the SA strategy,
we proposed a two stage flight control procedure using two autonomous control subsystems to address the dynamics variation
and performance requirement difference in initial and final stages of flight trajectory for a nontrivial nonlinear eight-rotor helicopter
model. This control strategy for chosen model of mini-TUAV has been verified by simulation of hovering maneuvers using software
package Simulink and demonstrated good performance for fast
stabilization of engines in hovering, consequently, fast SA with
economy in energy of batteries can be asserted during search-andrescue
operations.
Abstract: In this paper multi-objective genetic algorithms are
employed for Pareto approach optimization of ideal Turboshaft
engines. In the multi-objective optimization a number of conflicting
objective functions are to be optimized simultaneously. The
important objective functions that have been considered for
optimization are specific thrust (F/m& 0), specific fuel consumption
( P S ), output shaft power 0 (& /&) shaft W m and overall efficiency( ) O
η .
These objectives are usually conflicting with each other. The design
variables consist of thermodynamic parameters (compressor pressure
ratio, turbine temperature ratio and Mach number).
At the first stage single objective optimization has been
investigated and the method of NSGA-II has been used for multiobjective
optimization. Optimization procedures are performed for
two and four objective functions and the results are compared for
ideal Turboshaft engine. In order to investigate the optimal
thermodynamic behavior of two objectives, different set, each
including two objectives of output parameters, are considered
individually. For each set Pareto front are depicted. The sets of
selected decision variables based on this Pareto front, will cause the
best possible combination of corresponding objective functions.
There is no superiority for the points on the Pareto front figure,
but they are superior to any other point. In the case of four objective
optimization the results are given in tables.
Abstract: Abai Kunanbayev is famous for being enlightener,
composer, interpreter, social agent, philosopher, reformer, who
wanted to enrich Kazakh literature by emergence with Russian and
European culture, and also as a founder of Kazakh written literary
language. Abai Kunanbayev was born in 1845 in East Kazakhstan
area and passed away in 1904 in his hometown. His oeuvre absorbed
and reflected all changes in the life of Kazakh society of the second
half of XIX century. Because ХІХ century, especially its second half,
was an important transition period for Kazakhstan, which radically
changed traditional way of Kazakh society and predetermined further
development in consequence of activation of Russian colonial policy
and approval of commodity-money relations in Steppe Land.Abai
Kunanbayev, besides Arabic and Persian common words and
loanwords from Quran in his words of edification, had used a lot of
words of Arabic, Persian, Latin, Russian, Nogai, Shaghatai, Polish,
Greek, Turkish, which are used in the Kazakh language.
Abstract: The six sigma method is a project-driven management approach to improve the organization-s products, services, and processes by continually reducing defects in the organization. Understanding the key features, obstacles, and shortcomings of the six sigma method allows organizations to better support their strategic directions, and increasing needs for coaching, mentoring, and training. It also provides opportunities to better implement six sigma projects. The purpose of this paper is the survey of six sigma process and its impact on the organizational productivity. So I have studied key concepts , problem solving process of six sigmaas well as the survey of important fields such as: DMAIC, six sigma and productivity applied programme, and other advantages of six sigma. In the end of this paper, present research conclusions. (direct and positive relation between six sigma and productivity)
Abstract: Arbitrarily shaped video objects are an important
concept in modern video coding methods. The techniques presently
used are not based on image elements but rather video objects having
an arbitrary shape. In this paper, spatial shape error concealment
techniques to be used for object-based image in error-prone
environments are proposed. We consider a geometric shape
representation consisting of the object boundary, which can be
extracted from the α-plane. Three different approaches are used to
replace a missing boundary segment: Bézier interpolation, Bézier
approximation and NURBS approximation. Experimental results on
object shape with different concealment difficulty demonstrate the
performance of the proposed methods. Comparisons with proposed
methods are also presented.
Abstract: Today, Higher Education in a global scope is subordinated to the greater institutional controls through the policies of the Quality of Education. These include processes of over evaluation of all the academic activities: students- and professors- performance, educational logistics, managerial standards for the administration of institutions of higher education, as well as the establishment of the imaginaries of excellence and prestige as the foundations on which universities of the XXI century will focus their present and future goals and interests. But at the same time higher education systems worldwide are facing the most profound crisis of sense and meaning and attending enormous mutations in their identity. Based in a qualitative research approach, this paper shows the social configurations that the scholars at the Universities in Mexico build around the discourse of the Quality of Education, and how these policies put in risk the social recognition of these individuals.
Abstract: Although the usefulness of fuzzy databases has been
pointed out in several works, they are not fully developed in numerous
domains. A task that is mostly disregarded and which is the topic
of this paper is the determination of suitable inequalities for fuzzy
sets in fuzzy query languages. This paper examines which kinds
of fuzzy inequalities exist at all. Afterwards, different procedures
are presented that appear theoretically appropriate. By being applied
to various examples, their strengths and weaknesses are revealed.
Furthermore, an algorithm for an efficient computation of the selected
fuzzy inequality is shown.
Abstract: In the last decades to supply the various and different
demands of clients, a lot of manufacturers trend to use the mixedmodel
assembly line (MMAL) in their production lines, since this
policy make possible to assemble various and different models of the
equivalent goods on the same line with the MTO approach.
In this article, we determine the sequence of (MMAL) line, with
applying the kitting approach and planning of rest time for general
workers to reduce the wastages, increase the workers effectiveness
and apply the sector of lean production approach.
This Multi-objective sequencing problem solved in small size with
GAMS22.2 and PSO meta heuristic in 10 test problems and compare
their results together and conclude that their results are very similar
together, next we determine the important factors in computing the
cost, which improving them cost reduced. Since this problem, is NPhard
in large size, we use the particle swarm optimization (PSO)
meta-heuristic for solving it. In large size we define some test
problems to survey it-s performance and determine the important
factors in calculating the cost, that by change or improved them
production in minimum cost will be possible.
Abstract: In response to address different development challenges, Tanzania is striving to achieve its fourth attribute of the National Development Vision, i.e. to have a well educated and learned society by the year 2025. One of the most cost effective methods that can reach a large part of the society in a short time is to integrate ICT in education through e-learning initiatives. However, elearning initiatives are challenged by limited or lack of connectivity to majority of secondary schools, especially those in rural and remote areas. This paper has explores the possibility for rural secondary school to access online e-Learning resources from a centralized e- Learning Management System (e-LMS). The scope of this paper is limited to schools that have computers irrespective of internet connectivity, resulting in two categories schools; those with internet access and those without. Different connectivity configurations have been proposed according to the ICT infrastructure status of the respective schools. However, majority of rural secondary schools in Tanzania have neither computers nor internet connection. Therefore this is a challenge to be addressed for the disadvantaged schools to benefit from e-Learning initiatives.
Abstract: The purpose of this research was develop a biological
nutrient removal (BNR) system which has low energy consumption, sludge production, and land usage. These indicate that BNR system could be a alternative of future wastewater treatment in ubiquitous
city(U-city). Organics and nitrogen compounds could be removed by this system so that secondary or tertiary stages of wastewater treatment satisfy their standards. This system was composed of oxic and anoxic
filter filed with PVDC and POM media. Anoxic/oxic filter system operated under empty bed contact time of 4 hours by increasing
recirculation ratio from 0 to 100 %. The system removals of total nitrogen and COD were 76.3% and 93%, respectively. To be observed
internal behavior in this system SCOD, NH3-N, and NO3-N were
conducted and removal shows range of 25~100%, 59~99%, and
70~100%, respectively.
Abstract: Planning capacities when regenerating complex investment goods involves particular challenges in that the planning is subject to a large degree of uncertainty regarding load information. Using information fusion – by applying Bayesian Networks – a method is being developed for forecasting the anticipated expenditures (human labor, tool and machinery utilization, time etc.) for regenerating a good. The generated forecasts then later serve as a tool for planning capacities and ensure a greater stability in the planning processes.
Abstract: Web applications have become very complex and
crucial, especially when combined with areas such as CRM
(Customer Relationship Management) and BPR (Business Process
Reengineering), the scientific community has focused attention to
Web applications design, development, analysis, and testing, by
studying and proposing methodologies and tools. This paper
proposes an approach to automatic multi-dimensional concern
mining for Web Applications, based on concepts analysis, impact
analysis, and token-based concern identification. This approach lets
the user to analyse and traverse Web software relevant to a particular
concern (concept, goal, purpose, etc.) via multi-dimensional
separation of concerns, to document, understand and test Web
applications. This technique was developed in the context of WAAT
(Web Applications Analysis and Testing) project. A semi-automatic
tool to support this technique is currently under development.
Abstract: Mammographic images and data analysis to
facilitate modelling or computer aided diagnostic (CAD) software development should best be done using a common database that can handle various mammographic image file
formats and relate these to other patient information.
This would optimize the use of the data as both primary
reporting and enhanced information extraction of research data could be performed from the single dataset. One desired
improvement is the integration of DICOM file header information into the database, as an efficient and reliable source of supplementary patient information intrinsically
available in the images.
The purpose of this paper was to design a suitable database to link and integrate different types of image files and gather common information that can be further used for research
purposes. An interface was developed for accessing, adding,
updating, modifying and extracting data from the common
database, enhancing the future possible application of the data in CAD processing.
Technically, future developments envisaged include the creation of an advanced search function to selects image files
based on descriptor combinations. Results can be further used for specific CAD processing and other research. Design of a
user friendly configuration utility for importing of the required fields from the DICOM files must be done.
Abstract: Noise level has critical effects on the diagnostic
performance of signal-averaged electrocardiogram (SAECG), because
the true starting and end points of QRS complex would be masked by
the residual noise and sensitive to the noise level. Several studies and
commercial machines have used a fixed number of heart beats
(typically between 200 to 600 beats) or set a predefined noise level
(typically between 0.3 to 1.0 μV) in each X, Y and Z lead to perform
SAECG analysis. However different criteria or methods used to
perform SAECG would cause the discrepancies of the noise levels
among study subjects. According to the recommendations of 1991
ESC, AHA and ACC Task Force Consensus Document for the use of
SAECG, the determinations of onset and offset are related closely to
the mean and standard deviation of noise sample. Hence this study
would try to perform SAECG using consistent root-mean-square
(RMS) noise levels among study subjects and analyze the noise level
effects on SAECG. This study would also evaluate the differences
between normal subjects and chronic renal failure (CRF) patients in
the time-domain SAECG parameters.
The study subjects were composed of 50 normal Taiwanese and 20
CRF patients. During the signal-averaged processing, different RMS
noise levels were adjusted to evaluate their effects on three time
domain parameters (1) filtered total QRS duration (fQRSD), (2) RMS
voltage of the last QRS 40 ms (RMS40), and (3) duration of the low
amplitude signals below 40 μV (LAS40). The study results
demonstrated that the reduction of RMS noise level can increase
fQRSD and LAS40 and decrease the RMS40, and can further increase
the differences of fQRSD and RMS40 between normal subjects and
CRF patients. The SAECG may also become abnormal due to the
reduction of RMS noise level. In conclusion, it is essential to establish
diagnostic criteria of SAECG using consistent RMS noise levels for
the reduction of the noise level effects.
Abstract: Induction machine models used for steady-state and
transient analysis require machine parameters that are usually
considered design parameters or data. The knowledge of induction
machine parameters is very important for Indirect Field Oriented
Control (IFOC). A mismatched set of parameters will degrade the
response of speed and torque control. This paper presents an
improvement approach on rotor time constant adaptation in IFOC for
Induction Machines (IM). Our approach tends to improve the
estimation accuracy of the fundamental model for flux estimation.
Based on the reduced order of the IM model, the rotor fluxes and
rotor time constant are estimated using only the stator currents and
voltages. This reduced order model offers many advantages for real
time identification parameters of the IM.
Abstract: The influence of extrusion parameters on surface
quality and properties of AA6061+x% vol. SiC (x = 0; 2,5; 5; 7,5;10)
composites was discussed in this paper. The averages size of
AA6061 and SiC particles were 10.6 μm and 0.42 μm, respectively.
Two series of composites (I - compacts were preheated at extrusion
temperature through 0.5 h and cooled by water directly after process;
II - compacts were preheated through 3 hours and were not cooled)
were consolidated via powder metallurgy processing and extruded by
KoBo method. High values of density for both series of composites
were achieved. Better surface quality was observed for II series of
composites. Moreover, for these composites lower (compared to I
series) but more uniform strength properties over the cross-section of
the bar were noticed. Microstructure and Young-s modulus
investigations were made.
Abstract: Appropriate ventilation in a classroom is helpful for
enhancing air exchange rate and student concentration. This study
focuses on the effects of fenestration in a four-story school building by
performing numerical simulation of a building when considering
indoor and outdoor environments simultaneously. The wind profile
function embedded in PHOENICS code was set as the inlet boundary
condition in a suburban environment. Sixteen fenestration
combinations were compared in a classroom containing thirty seats.
This study evaluates mean age of air (AGE) and airflow pattern of a
classroom on different floors. Considering both wind profile and
fenestration effects, the airflow on higher floors is channeled toward
the area near ceiling in a room and causes older mean age of air in the
breathing zone. The results in this study serve as a useful guide for
enhancing natural ventilation in a typical school building.
Abstract: Optical Bursts Switching (OBS) is a relatively new
optical switching paradigm. Contention and burst loss in OBS
networks are major concerns. To resolve contentions, an interesting
alternative to discarding the entire data burst is to partially drop the
burst. Partial burst dropping is based on burst segmentation concept
that its implementation is constrained by some technical challenges,
besides the complexity added to the algorithms and protocols on both
edge and core nodes. In this paper, the burst segmentation concept is
investigated, and an implementation scheme is proposed and
evaluated. An appropriate dropping policy that effectively manages
the size of the segmented data bursts is presented. The dropping
policy is further supported by a new control packet format that
provides constant transmission overhead.