Abstract: In this paper, a worm-like micro robot designed for inpipe
application with intelligent active force control (AFC) capability
is modelled and simulated. The motion of the micro robot is based on
an impact drive mechanism (IDM) that is actuated using piezoelectric
device. The trajectory tracking performance of the modelled micro
robot is initially experimented via a conventional proportionalintegral-
derivative (PID) controller in which the dynamic response of
the robot system subjected to different input excitations is
investigated. Subsequently, a robust intelligent method known as
active force control with fuzzy logic (AFCFL) is later incorporated
into the PID scheme to enhance the system performance by
compensating the unwanted disturbances due to the interaction of the
robot with its environment. Results show that the proposed AFCFL
scheme is far superior than the PID control counterpart in terms of
the system-s tracking capability in the wake of the disturbances.
Abstract: Aggressive scaling of MOS devices requires use of ultra-thin gate oxides to maintain a reasonable short channel effect and to take the advantage of higher density, high speed, lower cost etc. Such thin oxides give rise to high electric fields, resulting in considerable gate tunneling current through gate oxide in nano regime. Consequently, accurate analysis of gate tunneling current is very important especially in context of low power application. In this paper, a simple and efficient analytical model has been developed for channel and source/drain overlap region gate tunneling current through ultra thin gate oxide n-channel MOSFET with inevitable deep submicron effect (DSME).The results obtained have been verified with simulated and reported experimental results for the purpose of validation. It is shown that the calculated tunnel current is well fitted to the measured one over the entire oxide thickness range. The proposed model is suitable enough to be used in circuit simulator due to its simplicity. It is observed that neglecting deep sub-micron effect may lead to large error in the calculated gate tunneling current. It is found that temperature has almost negligible effect on gate tunneling current. It is also reported that gate tunneling current reduces with the increase of gate oxide thickness. The impact of source/drain overlap length is also assessed on gate tunneling current.
Abstract: We propose a new approach on how to obtain the approximate solutions of Hamilton-Jacobi (HJ) equations. The process of the approximation consists of two steps. The first step is to transform the HJ equations into the virtual time based HJ equations (VT-HJ) by introducing a new idea of ‘virtual-time’. The second step is to construct the approximate solutions of the HJ equations through a computationally iterative procedure based on the VT-HJ equations. It should be noted that the approximate feedback solutions evolve by themselves as the virtual-time goes by. Finally, we demonstrate the effectiveness of our approximation approach by means of simulations with linear and nonlinear control problems.
Abstract: The problem of lot sizing, sequencing and scheduling
multiple products in flow line production systems has been studied
by several authors. Almost all of the researches in this area assumed
that setup times and costs are sequence –independent even though
sequence dependent setups are common in practice. In this paper we
present a new mixed integer non linear program (MINLP) and a
heuristic method to solve the problem in sequence dependent case.
Furthermore, a genetic algorithm has been developed which applies
this constructive heuristic to generate initial population. These two
proposed solution methods are compared on randomly generated
problems. Computational results show a clear superiority of our
proposed GA for majority of the test problems.
Abstract: The growing health hazardous impact of arsenic (As)
contamination in environment is the impetus of the present
investigation. Application of lactic acid bacteria (LAB) for the
removal of toxic and heavy metals from water has been reported.
This study was performed in order to isolate and characterize the Asresistant
LAB from mud and sludge samples for using as efficient As
uptaking probiotic. Isolation of As-resistant LAB colonies was
performed by spread plate technique using bromocresol purple
impregnated-MRS (BP-MRS) agar media provided with As @ 50
μg/ml. Isolated LAB were employed for probiotic characterization
process, acid and bile tolerance, lactic acid production, antibacterial
activity and antibiotic tolerance assays. After As-resistant and
removal characterizations, the LAB were identified using 16S rDNA
sequencing. A total of 103 isolates were identified as As-resistant
strains of LAB. The survival of 6 strains (As99-1, As100-2, As101-3,
As102-4, As105-7, and As112-9) was found after passing through the
sequential probiotic characterizations. Resistant pattern pronounced
hollow zones at As concentration >2000 μg/ml in As99-1, As100-2,
and As101-3 LAB strains, whereas it was found at ~1000 μg/ml in
rest 3 strains. Among 6 strains, the As uptake efficiency of As102-4
(0.006 μg/h/mg wet weight of cell) was higher (17 – 209%)
compared to remaining LAB. 16S rDNA sequencing data of 3 (As99-
1, As100-2, and As101-3) and 3 (As102-4, As105-7, and As112-9)
LAB strains clearly showed 97 to 99% (340 bp) homology to
Pediococcus dextrinicus and Pediococcus acidilactici, respectively.
Though, there was no correlation between the metal resistant and
removal efficiency of LAB examined but identified elevated As
removing LAB would probably be a potential As uptaking probiotic
agent. Since present experiment concerned with only As removal
from pure water, As removal and removal mechanism in natural
condition of intestinal milieu should be assessed in future studies.
Abstract: Bus Rapid Transit (BRT) has emerged as a cost-effective transport system for urban mobility. However its ability to stimulate land development remains largely unexplored. The study makes use of qualitative (interview method) and quantitative analysis (questionnaire survey and longitudinal analysis of property data) to investigate land development impact resulting from BRT in Beijing, China. The empirical analysis suggests that BRT has a positive impact on the residential and commercial property attractiveness along the busway corridor. The statistical analysis suggests that accessibility advantage conferred by BRT is capitalized into higher property price. The average price of apartments adjacent to a BRT station has gained a relatively faster increase than those not served by the BRT system. The capitalization effect mostly occurs after the full operation of BRT, and is more evident over time and particularly observed in areas which previously lack alternative mobility opportunity.
Abstract: Harmonic pollution and low power factor in power
systems caused by power converters have been of great concern. To
overcome these problems several converter topologies using
advanced semiconductor devices and control schemes have been
proposed. This investigation is to identify a low cost, small size,
efficient and reliable ac to dc converter to meet the input performance
index of UPS. The performance of single phase and three phase ac to
dc converter along with various control techniques are studied and
compared. The half bridge converter topology with linear current
control is identified as most suitable. It is simple, energy efficient
because of single switch power loss and transformer-less operation of
UPS. The results are validated practically using a prototype built
using IGBT and analog controller. The performance for both single
and three-phase system is verified. Digital implementation of closed
loop control achieves higher reliability. Its cost largely depends on
chosen bit precision. The minimal bit precision for optimum
converter performance is identified as 16-bit with fixed-point
operation. From the investigation and practical implementation it is
concluded that half bridge ac – dc converter along with digital linear
controller meets the performance index of UPS for single and three
phase systems.
Abstract: Chikungunya virus (CHICKV) is an arboviruses belonging to family Tagoviridae and is transmitted to human through by mosquito (Aedes aegypti and Aedes albopictus) bite. A large outbreak of chikungunya has been reported in India between 2006 and 2007, along with several other countries from South-East Asia and for the first time in Europe. It was for the first time that the CHICKV outbreak has been reported with mortality from Reunion Island and increased mortality from Asian countries. CHICKV affects all age groups, and currently there are no specific drugs or vaccine to cure the disease. The need of antiviral agents for the treatment of CHICKV infection and the success of virtual screening against many therapeutically valuable targets led us to carry out the structure based drug design against Chikungunya nSP2 protease (PDB: 3TRK). Highthroughput virtual screening of publicly available databases, ZINC12 and BindingDB, has been carried out using the Openeye tools and Schrodinger LLC software packages. Openeye Filter program has been used to filter the database and the filtered outputs were docked using HTVS protocol implemented in GLIDE package of Schrodinger LLC. The top HITS were further used for enriching the similar molecules from the database through vROCS; a shape based screening protocol implemented in Openeye. The approach adopted has provided different scaffolds as HITS against CHICKV protease. Three scaffolds: Indole, Pyrazole and Sulphone derivatives were selected based on the docking score and synthetic feasibility. Derivatives of Pyrazole were synthesized and submitted for antiviral screening against CHICKV.
Abstract: Data warehouse is a dedicated database used for querying and reporting. Queries in this environment show special characteristics such as multidimensionality and aggregation. Exploiting the nature of queries, in this paper we propose a query driven design framework. The proposed framework is general and allows a designer to generate a schema based on a set of queries.
Abstract: So much energy is used in high rise buildings to fulfill
the basic needs of users such as lighting and thermal comfort.
Malaysia has hot and humid climate, buildings especially high rise
buildings receive unnecessary solar radiation that cause more solar
heat gain. Energy use specially electricity consumption in high rise
buildings has increased. There have been growing concerns about
energy consumption and its effect on environment. Building, energy
and the environment are important issues that the designers should
consider to them. Self protected form is one of possible ways against
the impact of solar radiation in high rise buildings. The Energy
performance of building envelopes was investigated in term of the
Overall Thermal Transfer Value (OTTV ).In this paper, the amount
of OTTV reduction was calculated through OTTV Equations to
clear the effectiveness of self shading strategy on minimizing energy
consumption for cooling interior spaces in high rise buildings which
has considerable envelope areas against solar radiation. Also increasing
the optimum window area was investigated using self-shading
strategy in designing high rise buildings. As result, the significant
reduction in OTTV was shown based on WWR.In addition slight
increase was demonstrated in WWR that can influence on visible
comfort interior spaces.
Abstract: A better understanding of cloud forest characteristic in a tropical montane cloud forest at Khao Nan, Nakhon Si Thammarat on climatic, vegetation, soil and hydrology were studied during 18-21 April 2007. The results showed that as air temperature at Sanyen cloud forest increased, the percent relative humidity decreased. The amount of solar radiation at Sanyen cloud forest had a positive association with the amount of solar radiation at Parah forest. The amount of solar radiation at Sanyen cloud forest was very low with a range of 0-19 W/m2. On the other hand, the amount of solar radiation at Parah forest was high with a range of 0-1000 W/m2. There was no difference between leaf width, leaf length, leaf thickness and leaf area with increasing in elevations. As the elevations increased, bush height and tree height decreased. There was no association between bush width and bush ratio with elevation. As the elevations increased, the percent epiphyte cover and the percent soil moisture increased but water temperature, conductivity, and dissolved oxygen decreased. The percent soil moistures and organic contents were higher at elevations above 900 m than elevations below.
Abstract: With the advance of multimedia and diagnostic
images technologies, the number of radiographic images is increasing
constantly. The medical field demands sophisticated systems for
search and retrieval of the produced multimedia document. This
paper presents an ongoing research that focuses on the semantic
content of radiographic image documents to facilitate semantic-based
radiographic image indexing and a retrieval system. The proposed
model would divide a radiographic image document, based on its
semantic content, and would be converted into a logical structure or
a semantic structure. The logical structure represents the overall
organization of information. The semantic structure, which is bound
to logical structure, is composed of semantic objects with
interrelationships in the various spaces in the radiographic image.
Abstract: Today-s healthcare industries had become more
patient-centric than profession-centric, from which the issues of quality of healthcare and the patient safety are the major concerns in the modern healthcare facilities. An unplanned extubation (UE) may
be detrimental to the patient-s life, and thus is one of the major indexes
of patient safety and healthcare quality. A high UE rate not only
defeated the healthcare quality as well as the patient safety policy but
also the nurses- morality, and job satisfaction. The UE problem in a psychiatric hospital is unique and may be a tough challenge for the
healthcare professionals for the patients were mostly lacking communication capabilities. We reported with this essay a particular
project that was organized to reduce the UE rate from the current 2.3%
to a lower and satisfactory level in the long-term care units of a psychiatric hospital. The project was conducted between March 1st,
2011 and August 31st, 2011. Based on the error information gathered
from varied units of the hospital, the team analyzed the root causes
with possible solutions proposed to the meetings. Four solutions were
then concluded with consensus and launched to the units in question.
The UE rate was now reduced to a level of 0.17%. Experience from
this project, the procedure and the tools adopted would be good reference to other hospitals.
Abstract: An effort has been taken to simulate the combustion
and performance characteristics of biodiesel fuel in direct injection
(D.I) low heat rejection (LHR) diesel engine. Comprehensive
analyses on combustion characteristics such as cylinder pressure,
peak cylinder pressure, heat release and performance characteristics
such as specific fuel consumption and brake thermal efficiency are
carried out. Compression ignition (C.I) engine cycle simulation was
developed and modified in to LHR engine for both diesel and
biodiesel fuel. On the basis of first law of thermodynamics the
properties at each degree crank angle was calculated. Preparation and
reaction rate model was used to calculate the instantaneous heat
release rate. A gas-wall heat transfer calculations are based on the
ANNAND-s combined heat transfer model with instantaneous wall
temperature to analyze the effect of coating on heat transfer. The
simulated results are validated by conducting the experiments on the
test engine under identical operating condition on a turbocharged D.I
diesel engine. In this analysis 20% of biodiesel (derived from
Jatropha oil) blended with diesel and used in both conventional and
LHR engine. The simulated combustion and performance
characteristics results are found satisfactory with the experimental
value.
Abstract: Numerical parametric study is conducted to study the effects of ampoule rotation on the flows and the dopant segregation in vertical bridgman (vb) crystal growth. Calculations were performed in unsteady state. The extended darcy model, which includes the time derivative and coriolis terms, has been employed in the momentum equation. It’s found that the convection, and dopant segregation can be affected significantly by ampoule rotation, and the effect is similar to that by an axial magnetic field. Ampoule rotation decreases the intensity of convection and stretches the flow cell axially. When the convection is weak, the flow can be suppressed almost completely by moderate ampoule rotation and the dopant segregation becomes diffusion-controlled. For stronger convection, the elongated flow cell by ampoule rotation may bring dopant mixing into the bulk melt reducing axial segregation at the early stage of the growth. However, if the cellular flow cannot be suppressed completely, ampoule rotation may induce larger radial segregation due to poor mixing.
Abstract: One of the most important parameters to develop and
manage urban areas is appropriate selection of land surface to
develop green spaces in these areas. In this study, in order to identify
the most appropriate sites and areas cultivated for ornamental species
in Jiroft, Landsat Enhanced Thematic Mapper Plus (ETM+) images
due to extract the most important effective climatic and adaphic
parameters for growth ornamental species were used. After geometric
and atmospheric corrections applied, to enhance accuracy of multi
spectral (XS) bands, the fusion of Landsat XS bands by IRS-1D
panchromatic band (PAN) was performed. After field sampling to
evaluate the correlation between different factors in surface soil
sampling location and different bands digital number (DN) of ETM+
sensor on the same points, correlation tables formed using the best
computational model and the map of physical and chemical
parameters of soil was produced. Then the accuracy of them was
investigated by using kappa coefficient. Finally, according to
produced maps, the best areas for cultivation of recommended
species were introduced.
Abstract: This study investigated morphology of the Spanner Barb (Puntius lateristriga Valenciennes, 1842) and water quality at Thepchana waterfall. This study was conducted at Thepchana Waterfall, Khao Nan National Park from March to May 2007. There were 40 Spanner Barb collected with 20 males and 20 females. Males had an average of 5.57 cm in standard length, 6.62 cm in total length and 5.18 g in total body weight. Females had an average of 7.25 cm in standard length, 8.24 cm in total length and 10.96 g in total body weight. The length (L) – weight (W) relationships for combining sexes, males and females were LogW = -2.137 + 3.355logL, log W = -0.068 + 3.297logL, and log W = -2.068 + 3.297logL, respectively. The Spanner Barb were smaller size fish with a compressed form; terminal mouth; villiform teeth; ctenoid scale; concave tail; general body color yellowish olive, with slight reddish tint to fins; vertical band beginning below dorsal and horizontal stripe from base of tail almost to vertical band. They also had a vertical band midway between the eye and first vertical band. There was a black spot above anal fin. The bladder looked like J-shape. Inside of the bladder was found small insects and insect lava. The body length and the bowels length was 1:1 ratio. The water temperature ranged from 25.00 – 27.00 °C which was appropriate for their habitat characteristics. Acid - alkalinity ranged from 6.65 – 6.90 mg/l. Dissolved oxygen ranged from 4.55 – 4.70 mg/l. Water hardness ranged from 31.00 – 48.00 mg/l. The amount of ammonia was about 0.25 mg/l.
Abstract: Today automobile and aerospace industries realise Laser Beam Welding for a clean and non contact source of heating and fusion for joining of sheets. The welding performance is mainly based on by the laser welding parameters. Some concepts related to Artificial Neural Networks and how can be applied to model weld bead geometry and mechanical properties in terms of equipment parameters are reported in order to evaluate the accuracy and compare it with traditional modeling schemes. This review reveals the output features of Titanium and Aluminium weld bead geometry and mechanical properties such as ultimate tensile strength, yield strength, elongation and reduction of the area of the weld using Artificial Neural Network.
Abstract: This paper investigates the problem of tracking spa¬tiotemporal changes of a satellite image through the use of Knowledge Discovery in Database (KDD). The purpose of this study is to help a given user effectively discover interesting knowledge and then build prediction and decision models. Unfortunately, the KDD process for spatiotemporal data is always marked by several types of imperfections. In our paper, we take these imperfections into consideration in order to provide more accurate decisions. To achieve this objective, different KDD methods are used to discover knowledge in satellite image databases. Each method presents a different point of view of spatiotemporal evolution of a query model (which represents an extracted object from a satellite image). In order to combine these methods, we use the evidence fusion theory which considerably improves the spatiotemporal knowledge discovery process and increases our belief in the spatiotemporal model change. Experimental results of satellite images representing the region of Auckland in New Zealand depict the improvement in the overall change detection as compared to using classical methods.
Abstract: Electro-hydraulic power steering (EHPS) system for
the fuel rate reduction and steering feel improvement is comprised of
ECU including the logic which controls the steering system and BL
DC motor and produces the best suited cornering force, BLDC motor,
high pressure pump integrated module and basic oil-hydraulic circuit
of the commercial HPS system.
Electro-hydraulic system can be studied in two ways such as
experimental and computer simulation. To get accurate results in
experimental study of EHPS system, the real boundary management is
necessary which is difficult task. And the accuracy of the experimental
results depends on the preparation of the experimental setup and
accuracy of the data collection. The computer simulation gives
accurate and reliable results if the simulation is carried out considering
proper boundary conditions. So, in this paper, each component of
EHPS was modeled, and the model-based analysis and control logic
was designed by using AMESim