Abstract: High building constructions are increasing in south
beaches of the Caspian Sea because of tourist attractions and limitation of residential areas. According to saturated alluvial fields transfer of load from high structures to the soil by piles is inevitable.
In spite of most of these piles are under compression forces, tension piles are used in special conditions. Few studies have been conducted
because of the limited use of these piles. Tension capacity of openended pipe piles in full scale was tested in this study. The length of the bored piles was 420 up to 480 cm and all were in 120 cm
diameter. The results of testing 7 piles were compared with the results of relations given by researches.
Abstract: Threedimensional numerical simulations are conducted on a full scale CANDU Moderator and Transient variations of the temperature and velocity distributions inside the tank are determined. The results show that the flow and temperature distributions inside the moderator tank are three dimensional and no symmetry plane can be identified.Competition between the upward moving buoyancy driven flows and the downward moving momentum driven flows, results in the formation of circulation zones. The moderator tank operates in the buoyancy driven mode and any small disturbances in the flow or temperature makes the system unstable and asymmetric. Different types of temperature fluctuations are noted inside the tank: (i) large amplitude are at the boundaries between the hot and cold (ii) low amplitude are in the core of the tank (iii) high frequency fluctuations are in the regions with high velocities and (iv) low frequency fluctuations are in the regions with lower velocities.
Abstract: The microbial production of ethanol from biodiesel¬derived crude glycerol by Enterobacter aerogenes TISTR1468, under micro-aerobic and anaerobic conditions, was investigated. The experimental results showed that micro-aerobic conditions were more favorable for cellular growth (4.0 g/L DCW), ethanol production (20.7 g/L) as well as the ethanol yield (0.47 g/g glycerol) than anaerobic conditions (1.2 g/L DCW, 6.3 g/L ethanol and 0.72 g/g glycerol, respectively). Crude glycerol (100 g/L) was consumed completely with the rate of 1.80 g/L/h. Two-stage fermentation (combination of micro-aerobic and anaerobic condition) exhibited higher ethanol production (24.5 g/L) than using one-stage fermentation (either micro-aerobic or anaerobic condition. The two- stage configuration, exhibited slightly higher crude glycerol consumption rate (1.81 g/L/h), as well as ethanol yield (0.56 g/g) than the one-stage configuration. Therefore, two-stage process was selected for ethanol production from E. aerogenes TISTR1468 in scale-up studies.
Abstract: This paper presents the doping profile measurement
and characterization technique for the pocket implanted nano scale
n-MOSFET. Scanning capacitance microscopy and atomic force
microscopy have been used to image the extent of lateral dopant
diffusion in MOS structures. The data are capacitance vs. voltage
measurements made on a nano scale device. The technique is nondestructive
when imaging uncleaved samples. Experimental data from
the published literature are presented here on actual, cleaved device
structures which clearly indicate the two-dimensional dopant profile
in terms of a spatially varying modulated capacitance signal. Firstorder
deconvolution indicates the technique has much promise for
the quantitative characterization of lateral dopant profiles. The pocket
profile is modeled assuming the linear pocket profiles at the source
and drain edges. From the model, the effective doping concentration
is found to use in modeling and simulation results of the various
parameters of the pocket implanted nano scale n-MOSFET. The
potential of the technique to characterize important device related
phenomena on a local scale is also discussed.
Abstract: To understand working features of a micro combustor,
a computer code has been developed to study combustion of
hydrogen–air mixture in a series of chambers with same shape aspect
ratio but various dimensions from millimeter to micrometer level.
The prepared algorithm and the computer code are capable of
modeling mixture effects in different fluid flows including chemical
reactions, viscous and mass diffusion effects. The effect of various
heat transfer conditions at chamber wall, e.g. adiabatic wall, with
heat loss and heat conduction within the wall, on the combustion is
analyzed. These thermal conditions have strong effects on the
combustion especially when the chamber dimension goes smaller and
the ratio of surface area to volume becomes larger.
Both factors, such as larger heat loss through the chamber wall
and smaller chamber dimension size, may lead to the thermal
quenching of micro-scale combustion. Through such systematic
numerical analysis, a proper operation space for the micro-combustor
is suggested, which may be used as the guideline for microcombustor
design. In addition, the results reported in this paper
illustrate that the numerical simulation can be one of the most
powerful and beneficial tools for the micro-combustor design,
optimization and performance analysis.
Abstract: We demonstrate the synthesis of intermediary views
within a sequence of color encoded, materials discriminating, X-ray
images that exhibit animated depth in a visual display. During the
image acquisition process, the requirement for a linear X-ray detector
array is replaced by synthetic image. Scale Invariant Feature
Transform, SIFT, in combination with material segmented morphing
is employed to produce synthetic imagery. A quantitative analysis of
the feature matching performance of the SIFT is presented along with
a comparative study of the synthetic imagery. We show that the total
number of matches produced by SIFT reduces as the angular
separation between the generating views increases. This effect is
accompanied by an increase in the total number of synthetic pixel
errors. The trends observed are obtained from 15 different luggage
items. This programme of research is in collaboration with the UK
Home Office and the US Dept. of Homeland Security.
Abstract: This paper presents an integrated model that
automatically measures the change of rivers, damage area of bridge
surroundings, and change of vegetation. The proposed model is on the
basis of a neurofuzzy mechanism enhanced by SOM optimization
algorithm, and also includes three functions to deal with river imagery.
High resolution imagery from FORMOSAT-2 satellite taken before
and after the invasion period is adopted. By randomly selecting a
bridge out of 129 destroyed bridges, the recognition results show that
the average width has increased 66%. The ruined segment of the
bridge is located exactly at the most scour region. The vegetation
coverage has also reduced to nearly 90% of the original. The results
yielded from the proposed model demonstrate a pinpoint accuracy rate
at 99.94%. This study brings up a successful tool not only for
large-scale damage assessment but for precise measurement to
disasters.
Abstract: The interaction of tunneling or mining with
groundwater has become a very relevant problem not only due to the
need to guarantee the safety of workers and to assure the efficiency of
the tunnel drainage systems, but also to safeguard water resources
from impoverishment and pollution risk. Therefore it is very
important to forecast the drainage processes (i.e., the evaluation of
drained discharge and drawdown caused by the excavation). The aim
of this study was to know better the system and to quantify the flow
drained from the Fontane mines, located in Val Germanasca (Turin,
Italy). This allowed to understand the hydrogeological local changes
in time. The work has therefore been structured as follows: the
reconstruction of the conceptual model with the geological,
hydrogeological and geological-structural study; the calculation of
the tunnel inflows (through the use of structural methods) and the
comparison with the measured flow rates; the water balance at the
basin scale. In this way it was possible to understand what are the
relationships between rainfall, groundwater level variations and the
effect of the presence of tunnels as a means of draining water.
Subsequently, it the effects produced by the excavation of the mining
tunnels was quantified, through numerical modeling. In particular,
the modeling made it possible to observe the drawdown variation as a
function of number, excavation depth and different mines linings.
Abstract: A different concept for designing and detailing of
reinforced concrete precast frame structures is analyzed in this paper.
The new detailing of the joints derives from the special hybrid
moment frame joints. The special reinforcements of this alternative
detailing, named modified special hybrid joint, are bondless with
respect to both column and beams. Full scale tests were performed on
a plan model, which represents a part of 5 story structure, cropped in
the middle of the beams and columns spans. Theoretical approach
was developed, based on testing results on twice repaired model,
subjected to lateral seismic type loading. Discussion regarding the
modified special hybrid joint behavior and further on widening
research needed concludes the presentation.
Abstract: Ten percent of the population will develop plantar
fasciitis (PF) during their lifetime. Two million people are treated
yearly accounting for 11-15% of visits to medical professionals.
Treatment ranges from conservative to surgical intervention. The
purpose of this study was to assess the effects of extracorporeal
shockwave therapy (ECSWT) on heel pain, function, range of motion
(ROM), and strength in patients with PF. One hundred subjects were
treated with ECSWT and measures were taken before and three
months after treatment. There was significant differences in visual
analog scale scores for pain at rest (p=0.0001); after activity (p=
0.0001) and; overall improvement (p=0.0001). There was also
significant improvement in Lower Extremity Functional Scale scores
(p=0.0001); ankle plantarflexion (p=0.0001), dorsiflexion (p=0.001),
and eversion (p=0.017),and first metatarsophalangeal joint flexion
(p=0.002) and extension (p=0.003) ROM. ECSWT is an effective
treatment improving heel pain, function and ROM in patients with
PF.
Abstract: This study investigates the in-situ regeneration of deactivated Pt-Pd catalyst in a laboratory-scale catalysis reactor. Different regeneration conditions are tested and the activity and characteristics of regenerated catalysts are analyzed. Experimental results show that the conversion efficiencies of C3H6 by different regenerated Pt-Pd catalysts were significantly improved from 77%, 55% and 41% to 86%, 98% and 99%, respectively. The best regeneration conditions was 52ppm ozone, 500oC, and 10min. Regeneration temperature has more influences than ozone concentration and regeneration time. With the comparisons of characteristics of deactivated catalyst and regenerated catalyst, the major poison species (carbon, metals, chloride, and sulfate) on the spent catalysts can be effectively removed by ozone regeneration.
Abstract: This research focuses on micro-enterprise of
Malaysian Malays that are involved in very small-scaled business
activities. Among them include food stall and burger stall operators,
night market hawkers, grocery store operators as well as construction
and small service activities works. The study seeks to explore why
some micro-entrepreneurs still lag in entrepreneurship and what
needs to be rectified. This quantitative study is conducted on 173
Malay micro-enterprise owners (MEOs) and 58 Malay failed microenterprise
owners (FMEOs) involved in all range of businesses
throughout the state of Perak, Malaysia. The main aims are to
identify the gaps between the failed micro-enterprise owners
(FMEOs) and existing micro-enterprise owners (MEOs) and the
problems faced among FMEOs. The results reveal that the MEOs had
strong motivations and better marketing approaches as compared to
FMEOs. Furthermore, the FMEOs failed in the business ventures
mainly due to lack of management, sales and marketing skills and
poor competitive abilities to keep up with rivals.
Abstract: In the meat processing industry the substitution of
meat with non-meat ingredients is considered an important strategy
for reducing overall production costs. The main purpose of the
current research was to evaluate differences in physical-chemical
composition of cooked sausage with different legumes additions.
Peas (Pisum sativum), beans (Phaseolus vulgaris) and lentil (Lens
culinaris) were used in preparation of sausages. The legumes at
proportion of 20% of the total weight of meat were added in
sausages. The whole ingredients were mixed, filled into casing,
compressed, cooked and cooled. After storage the samples were
sensory evaluated. The sensory evaluation was carried out using the
nine point hedonic scale and line scale. Sausages without legumes
flour was used as control sample. The main conclusion of the current
research the legumes flour can be successfully used for cooked
sausages production.
Abstract: Since atmosphere pressure field is an actual envoy of
climatic signal the atmospheric Highs and Lows should be attributed
to the key active focal points within the ocean-atmosphere interplay
system. Here we were set a task to determine how the dynamics of
those centres of action relates to the climate change both on regional
and global scales. For this target the near-surface temperature and
atmospheric pressure differences between the Icelandic Low and the
Azores High were considered. The secular term of phase states of the
system under consideration was found divided into three
nonintersecting subsets. Each of that was put in consequence with
one of three climatic scenarios related to the periods of 1905-1935
(relatively warm phase), 1940-1970 (cold phase) and 1980-2000
(warm phase).
Abstract: Small-scale RC models of both piles and tunnel ducts
were produced as mockups of reality and loaded under soil
confinement conditionsto investigate the damage evolution of
structural RC interacting with soil. Experimental verifications usinga
3D nonlinear FE analysis program called COM3D, which was
developed at the University of Tokyo, are introduced. This analysis
has been used in practice for seismic performance assessment of
underground ducts and in-ground LNG storage tanks in consideration
of soil-structure interactionunder static and dynamic loading. Varying
modes of failure of RCpilessubjected to different magnitudes of soil
confinement were successfully reproduced in the proposed small-scale
experiments and numerically simulated as well. Analytical simulation
was applied to RC tunnel mockups under a wide variety of depth and
soil confinement conditions, and reasonable matching was confirmed.
Abstract: Numerical design optimization is a powerful tool that
can be used by engineers during any stage of the design process.
There are many different applications for structural optimization. A
specific application that will be discussed in the following paper is
experimental data matching. Data obtained through tests on a physical
structure will be matched with data from a numerical model of that
same structure. The data of interest will be the dynamic characteristics
of an antenna structure focusing on the mode shapes and modal
frequencies. The structure used was a scaled and simplified model of
the Karoo Array Telescope-7 (KAT-7) antenna structure.
This kind of data matching is a complex and difficult task. This
paper discusses how optimization can assist an engineer during the
process of correlating a finite element model with vibration test data.
Abstract: This paper discusses aspects of re-design of loadshedding
schemes with respect to actual developments in the Kosovo
power system. Load-shedding is a type of emergency control that is
designed to ensure system stability by reducing power system load to
match the power generation supply. This paper presents a new
adaptive load-shedding scheme that provides emergency protection
against excess frequency decline, in cases when the Kosovo power
system might be disconnected from the regional transmission
network. The proposed load-shedding scheme uses the local
frequency rate information to adapt the load-shedding pattern to suit
the size and location of the occurring disturbance. The proposed
scheme is tested in a software simulation on a large scale PSS/E
model which represents nine power system areas of Southeast Europe
including the Kosovo power system.
Abstract: Real world Speaker Identification (SI) application
differs from ideal or laboratory conditions causing perturbations that
leads to a mismatch between the training and testing environment
and degrade the performance drastically. Many strategies have been
adopted to cope with acoustical degradation; wavelet based Bayesian
marginal model is one of them. But Bayesian marginal models
cannot model the inter-scale statistical dependencies of different
wavelet scales. Simple nonlinear estimators for wavelet based
denoising assume that the wavelet coefficients in different scales are
independent in nature. However wavelet coefficients have significant
inter-scale dependency. This paper enhances this inter-scale
dependency property by a Circularly Symmetric Probability Density
Function (CS-PDF) related to the family of Spherically Invariant
Random Processes (SIRPs) in Log Gabor Wavelet (LGW) domain
and corresponding joint shrinkage estimator is derived by Maximum
a Posteriori (MAP) estimator. A framework is proposed based on
these to denoise speech signal for automatic speaker identification
problems. The robustness of the proposed framework is tested for
Text Independent Speaker Identification application on 100 speakers
of POLYCOST and 100 speakers of YOHO speech database in three
different noise environments. Experimental results show that the
proposed estimator yields a higher improvement in identification
accuracy compared to other estimators on popular Gaussian Mixture
Model (GMM) based speaker model and Mel-Frequency Cepstral
Coefficient (MFCC) features.
Abstract: In this paper the features of multiple material gate
silicon-on-insulator MOSFETs are presented and compared with
single material gate silicon-on-insulator MOSFET structures. The
results indicate that the multiple material gate structures reduce short
channel effects such as drain induce barrier lowering, hot electron
effect and better current characteristics in comparison with single
material structures
Abstract: The present study examines the mediating effect of
online flow experience on the relationship between extraversionintroversion,
locus of control and loneliness, and depression and
satisfaction with life. The data was obtained using a structured
questionnaire prepared by adapting standardized scales available from
a sample of 102 engineering students from different technical
institutions at Bhubaneswar, India. The results indicate that there is a
positive significant relationship between introversion, external locus
of control, loneliness, depression and online flow experience, and
extraversion, internal locus of control and satisfaction with life. The
results also suggest that online flow experience mediates the
relationship between the aforementioned variables.