Abstract: The main goal of this paper is to study Statistical Process Control (SPC) with Exponentially Weighted Moving Average (EWMA) control chart when observations are serially-correlated. The characteristic of control chart is Average Run Length (ARL) which is the average number of samples taken before an action signal is given. Ideally, an acceptable ARL of in-control process should be enough large, so-called (ARL0). Otherwise it should be small when the process is out-of-control, so-called Average of Delay Time (ARL1) or a mean of true alarm. We find explicit formulas of ARL for EWMA control chart for Seasonal Autoregressive and Moving Average processes (SARMA) with Exponential white noise. The results of ARL obtained from explicit formula and Integral equation are in good agreement. In particular, this formulas for evaluating (ARL0) and (ARL1) be able to get a set of optimal parameters which depend on smoothing parameter (λ) and width of control limit (H) for designing EWMA chart with minimum of (ARL1).
Abstract: In this investigation Salicylic acid, Sulfosalicylic acid
and Acetyl salicylic acid were chosen as a sample for thin layer
chromatography (TLC) on silica gel plates. Bicarbonate buffer at
different pH containing different amounts of boric acid was applied
as mobile phase. Specific interaction of these substances with boric
acid has effect on Rf in thin layer chromatography. Regular and
similar trend was observed in variations of Rf for mentioned
compounds in TLC by altering of percentages of boric acid in mobile
phase in pH range of 8-10. Also effect of organic solvent, mixture of
water/ organic solvent and organic solvent containing boric acid as
mobile phase was studied.
Abstract: In July 2012, an indoor/outdoor monitoring
programme was undertaken in two university sports facilities: a
fronton and a gymnasium. Comfort parameters (temperature, relative
humidity, CO and CO2) and total volatile organic compounds
(VOCs) were continuously monitored. Concentrations of NO2,
carbonyl compounds and individual VOCs were obtained. Low
volume samplers were used to collect particulate matter (PM10). The
minimum ventilation rates stipulated for acceptable indoor air quality
were observed in both sports facilities. It was found that cleaning
activities may have a large influence on the VOC levels. Acrolein
was one of the most abundant carbonyl compounds, showing
concentrations above the recommended limit. Formaldehyde was
detected at levels lower than those commonly reported for other
indoor environments. The PM10 concentrations obtained during the
occupancy periods ranged between 38 and 43μgm-3 in the fronton and
from 154 to 198μgm-3 in the gymnasium.
Abstract: In this research paper we have presented control
architecture for robotic arm movement and trajectory planning using
Fuzzy Logic (FL) and Genetic Algorithms (GAs). This architecture is
used to compensate the uncertainties like; movement, friction and
settling time in robotic arm movement. The genetic algorithms and
fuzzy logic is used to meet the objective of optimal control
movement of robotic arm. This proposed technique represents a
general model for redundant structures and may extend to other
structures. Results show optimal angular movement of joints as result
of evolutionary process. This technique has edge over the other
techniques as minimum mathematics complexity used.
Abstract: A scalable QoS aware multicast deployment in
DiffServ networks has become an important research dimension in
recent years. Although multicasting and differentiated services are
two complementary technologies, the integration of the two
technologies is a non-trivial task due to architectural conflicts
between them. A popular solution proposed is to extend the
functionality of the DiffServ components to support multicasting. In
this paper, we propose an algorithm to construct an efficient QoSdriven
multicast tree, taking into account the available bandwidth per
service class. We also present an efficient way to provision the
limited available bandwidth for supporting heterogeneous users. The
proposed mechanism is evaluated using simulated tests. The
simulated result reveals that our algorithm can effectively minimize
the bandwidth use and transmission cost
Abstract: The purpose of this study is to identify ideal urban
design elements of waterfronts and to analyze the differences in users-
cognition among these elements. This study follows three steps as
following: first is identifying the urban design elements of waterfronts
from literature review and second is evaluating intended users-
cognition of urban design elements in urban waterfronts. Lastly, third
is analyzing the users- cognition differences. As the result, evaluations
of waterfront areas by users show similar features that non-waterfront
urban design elements contain the highest degree of importance. This
indicates the difference of users- cognition has dimensions of
frequency and distance, and demonstrates differences in the aspect of
importance than of satisfaction. Multi-Dimensional Scaling Method
verifies differences among their cognition. This study provides
elements to increase satisfaction of users from differences of their
cognition on design elements for waterfronts. It also suggests
implications on elements when waterfronts are built.
Abstract: A systems approach model for prostate cancer in prostate duct, as a sub-system of the organism is developed. It is accomplished in two steps. First this research work starts with a nonlinear system of coupled Fokker-Plank equations which models continuous process of the system like motion of cells. Then extended to PDEs that include discontinuous processes like cell mutations, proliferation and deaths. The discontinuous processes is modeled by using intensity poisson processes. The model incorporates the features of the prostate duct. The system of PDEs spatial coordinate is along the proximal distal axis. Its parameters depend on features of the prostate duct. The movement of cells is biased towards distal region and mutations of prostate cancer cells is localized in the proximal region. Numerical solutions of the full system of equations are provided, and are exhibit traveling wave fronts phenomena. This motivates the use of the standard transformation to derive a canonically related system of ODEs for traveling wave solutions. The results obtained show persistence of prostate cancer by showing that the non-negative cone for the traveling wave system is time invariant. The traveling waves have a unique global attractor is proved also. Biologically, the global attractor verifies that evolution of prostate cancer stem cells exhibit the avascular tumor growth. These numerical solutions show that altering prostate stem cell movement or mutation of prostate cancer cells lead to avascular tumor. Conclusion with comments on clinical implications of the model is discussed.
Abstract: The spiral angle of the elementary cellulose fibril in
the wood cell wall, often called microfibril angle, (MFA). Microfibril
angle in hardwood is one of the key determinants of solid timber
performance due to its strong influence on the stiffness, strength,
shrinkage, swelling, thermal-dynamics mechanical properties and
dimensional stability of wood. Variation of MFA (degree) in the S2
layer of the cell walls among Acacia mangium trees was determined
using small-angle X-ray scattering (SAXS). The length and
orientation of the microfibrils of the cell walls in the irradiated
volume of the thin samples are measured using SAXS and optical
microscope for 3D surface measurement. The undetermined
parameters in the analysis are the MFA, (M) and the standard
deviation (σФ) of the intensity distribution arising from the wandering
of the fibril orientation about the mean value. Nine separate pairs of
values are determined for nine different values of the angle of the
incidence of the X-ray beam relative to the normal to the radial
direction in the sample. The results show good agreement. The
curve distribution of scattered intensity for the real cell wall structure
is compared with that calculated with that assembly of rectangular
cells with the same ratio of transverse to radial cell wall length. It is
demonstrated that for β = 45°, the peaks in the curve intensity
distribution for the real and the rectangular cells coincide. If this
peak position is Ф45, then the MFA can be determined from the
relation M = tan-1 (tan Ф45 / cos 45°), which is precise for rectangular
cells. It was found that 92.93% of the variation of MFA can be
attributed to the distance from pith to bark. Here we shall present our
results of the MFA in the cell wall with respect to its shape, structure
and the distance from pith to park as an important fast check and yet
accurate towards the quality of wood, its uses and application.
Abstract: We present a new intuitionistic fuzzy aggregation
operator called the intuitionistic fuzzy ordered weighted
averaging-weighted average (IFOWAWA) operator. The main
advantage of the IFOWAWA operator is that it unifies the OWA
operator with the WA in the same formulation considering the degree
of importance that each concept has in the aggregation. Moreover, it is
able to deal with an uncertain environment that can be assessed with
intuitionistic fuzzy numbers. We study some of its main properties and
we see that it has a lot of particular cases such as the intuitionistic
fuzzy weighted average (IFWA) and the intuitionistic fuzzy OWA
(IFOWA) operator. Finally, we study the applicability of the new
approach on a financial decision making problem concerning the
selection of financial strategies.
Abstract: The precision of heat flux simulation influences the
temperature field and test aberration for TB test and also reflects the
test level for spacecraft development. This paper describes TB tests for
a small satellite using solar simulator, electric heaters, calrod heaters
to evaluate the difference of the three methods. Under the same
boundary condition, calrod heaters cases were about 6oC higher than
solar simulator cases and electric heaters cases for
non-external-heat-flux cases (extreme low temperature cases). While
calrod heaters cases and electric heaters cases were 5~7oC and 2~3oC
lower than solar simulator cases respectively for high temperature
cases. The results show that the solar simulator is better than calrod
heaters for its better collimation, non-homogeneity and stability.
Abstract: In this paper electrical characteristics of various kinds
of multiple-gate silicon nanowire transistors (SNWT) with the
channel length equal to 7 nm are compared. A fully ballistic quantum
mechanical transport approach based on NEGF was employed to
analyses electrical characteristics of rectangular and cylindrical
silicon nanowire transistors as well as a Double gate MOS FET. A
double gate, triple gate, and gate all around nano wires were studied
to investigate the impact of increasing the number of gates on the
control of the short channel effect which is important in nanoscale
devices. Also in the case of triple gate rectangular SNWT inserting
extra gates on the bottom of device can improve the application of
device. The results indicate that by using gate all around structures
short channel effects such as DIBL, subthreshold swing and delay
reduces.
Abstract: Current image-based individual human recognition
methods, such as fingerprints, face, or iris biometric modalities
generally require a cooperative subject, views from certain aspects,
and physical contact or close proximity. These methods cannot
reliably recognize non-cooperating individuals at a distance in the
real world under changing environmental conditions. Gait, which
concerns recognizing individuals by the way they walk, is a relatively
new biometric without these disadvantages. The inherent gait
characteristic of an individual makes it irreplaceable and useful in
visual surveillance.
In this paper, an efficient gait recognition system for human
identification by extracting two features namely width vector of
the binary silhouette and the MPEG-7-based region-based shape
descriptors is proposed. In the proposed method, foreground objects
i.e., human and other moving objects are extracted by estimating
background information by a Gaussian Mixture Model (GMM) and
subsequently, median filtering operation is performed for removing
noises in the background subtracted image. A moving target classification
algorithm is used to separate human being (i.e., pedestrian)
from other foreground objects (viz., vehicles). Shape and boundary
information is used in the moving target classification algorithm.
Subsequently, width vector of the outer contour of binary silhouette
and the MPEG-7 Angular Radial Transform coefficients are taken as
the feature vector. Next, the Principal Component Analysis (PCA)
is applied to the selected feature vector to reduce its dimensionality.
These extracted feature vectors are used to train an Hidden Markov
Model (HMM) for identification of some individuals. The proposed
system is evaluated using some gait sequences and the experimental
results show the efficacy of the proposed algorithm.
Abstract: In this paper, Tobephobia (TBP) alludes to the fear of
failure experienced by teachers to manage curriculum change. TBP is
an emerging concept and it extends the boundaries of research in
terms of how we view achievement and failure in education.
Outcomes-based education (OBE) was introduced fifteen years ago
in South African schools without simultaneously upgrading teachers-
professional competencies. This exploratory research, therefore
examines a simple question: What is the impact of TBP and OBE on
teachers? Teacher ineptitude to cope with the OBE curriculum in the
classroom is a serious problem affecting large numbers of South
African teachers. This exploratory study sought to determine the
perceived negative impact of OBE and TBP on teachers. A survey
was conducted amongst 311 teachers in Port Elizabeth and Durban,
South Africa. The results confirm the very negative impact of TBP
and OBE on teachers. This exploratory study authenticates the
existence of TBP.
Abstract: Experimental data are presented to show the influence of different types of chemical demulsifier on the stability and demulsification of emulsions. Three groups of demulsifier with different functional groups were used in this work namely amines, alcohol and polyhydric alcohol. The results obtained in this study have exposed the capability of chemical breaking agents in destabilization of water in crude oil emulsions. From the present study, found that molecular weight of the demulsifier were influent the capability of the emulsion to separate.
Abstract: Many difficulties are faced in the process of learning
computer programming. This paper will propose a system framework
intended to reduce cognitive load in learning programming. In first
section focus is given on the process of learning and the
shortcomings of the current approaches to learning programming.
Finally the proposed prototype is suggested along with the
justification of the prototype. In the proposed prototype the concept
map is used as visualization metaphor. Concept maps are similar to
the mental schema in long term memory and hence it can reduce
cognitive load well. In addition other method such as part code
method is also proposed in this framework to can reduce cognitive
load.
Abstract: Fructooligosaccharides derived from microbial enzyme especially from fungal sources has been received particular attention due to its beneficial effects as prebiotics and mass production. However, fungal fermentation is always cumbersome due to its broth rheology problem that will eventually affect the production of FOS. This study investigated the efficiency of immobilized cell system using rotating fibrous bed bioreactor (RFBB) in producing fructooligosaccharides (FOS). A comparative picture with respect to conventional stirred tank bioreactor (CSTB) and RFBB has been presented. To demonstrate the effect of agitation intensity and aeration rate, a laboratory-scale bioreactor 2.5 L was operated in three phases (high, medium, low) for 48 hours. Agitation speed has a great influence on P. simplicissimum fermentation for FOS production, where the volumetric FOS productivity using RFBB is increased with almost 4 fold compared to the FOS productivity in CSTB that only 0.319 g/L/h. Rate of FOS production increased up to 1.2 fold when immobilized cells system was employed at aeration rate similar to the freely suspended cells at 2.0 vvm.
Abstract: Pakistani doctors (MBBS) are emigrating towards developed countries for professional adjustments. This study aims to highlight causes and consequences of doctors- brain drain from Pakistan. Primary data was collected from Mayo Hospital, Lahore by interviewing doctors (n=100) through systematic random sampling technique. It found that various socio-economic and political conditions are working as push and pull factors for brain drain of doctors in Pakistan. Majority of doctors (83%) declared poor remunerations and professional infrastructure of health department as push factor of doctors- brain drain. 81% claimed that continuous instability in political situation and threats of terrorism are responsible for emigration of doctors. 84% respondents considered fewer opportunities of further studies responsible for their emigration. Brain drain of doctors is affecting health sector-s policies / programs, standard doctor-patient ratios and quality of health services badly.
Abstract: Many computational techniques were applied to
solution of heat conduction problem. Those techniques were the
finite difference (FD), finite element (FE) and recently meshless
methods. FE is commonly used in solution of equation of heat
conduction problem based on the summation of stiffness matrix of
elements and the solution of the final system of equations. Because
of summation process of finite element, convergence rate was
decreased. Hence in the present paper Cellular Automata (CA)
approach is presented for the solution of heat conduction problem.
Each cell considered as a fixed point in a regular grid lead to the
solution of a system of equations is substituted by discrete systems of
equations with small dimensions. Results show that CA can be used
for solution of heat conduction problem.
Abstract: Nanostructured Iron Oxide with different
morphologies of rod-like and granular have been suc-cessfully
prepared via a solid-state reaction in the presence of NaCl, NaBr, NaI
and NaN3, respectively. The added salts not only prevent a drastic
increase in the size of the products but also provide suitable
conditions for the oriented growth of primary nanoparticles. The
formation mechanisms of these materials by solid-state reaction at
ambient temperature are proposed. The photocatalytic experiments
for congo red (CR) have demonstrated that the mixture of α-Fe2O3
and Fe3O4 nanostructures were more efficient than α-Fe2O3
nanostructures.
Abstract: Gold passbook is an investing tool that is especially
suitable for investors to do small investment in the solid gold. The gold
passbook has the lower risk than other ways investing in gold, but its
price is still affected by gold price. However, there are many factors
can cause influences on gold price. Therefore, building a model to
predict the price of gold passbook can both reduce the risk of
investment and increase the benefits. This study investigates the
important factors that influence the gold passbook price, and utilize
the Group Method of Data Handling (GMDH) to build the predictive
model. This method can not only obtain the significant variables but
also perform well in prediction. Finally, the significant variables of
gold passbook price, which can be predicted by GMDH, are US dollar
exchange rate, international petroleum price, unemployment rate,
whole sale price index, rediscount rate, foreign exchange reserves,
misery index, prosperity coincident index and industrial index.