Abstract: Worldwide interests for the renewable energy are increasing due to environmental and climate changes from traditional petroleum related energy sources. To account for these social needs, ligneous biomass energy is considered as one of the environmentally friend energy solutions. The wood torrefaction process is a feasible method to improve the properties of the biomass fuel and makes the wood have low moisture, lower smoke emission and increased heating value. In this work, therefore, the moisture evaporation model which largely affects energy efficiency of ligneous biomass through moisture contents and heating value relative to its weight is studied with numerical modeling approach by analyzing the effects of torrefaction furnace temperature. The results show that the temperature and moisture fraction of wood decrease by increasing the furnace temperature. When the torrefaction temperature is lower than 423K, there were little changes of the moisture fraction in the wood. Also, it can be found that charcoal is produced more slowly when the torrefaction temperature is lower than 573K.
Abstract: The heat and mass transfer was investigated during the falling rate period of spray drying of a slurry droplet. The effect of the porosity of crust layer formed from primary particles during liquid evaporation was studied numerically using the developed mathematical model which takes into account the heat and mass transfer in the core and crust regions, the movement of the evaporation interface, and the external heat and mass transfer between the drying air and the droplet surface. It was confirmed that the heat transfer through the crust layer was more intense in the case of the dense droplet than the loose one due to the enhanced thermal conduction resulting in the higher average droplet temperature. The mass transfer was facilitated in the crust layer of loose droplet owing to the large pore space available for diffusion of water vapor from the evaporation interface to the outer droplet surface. The longer drying time is required for the droplet of high porosity to reach the final moisture content than that for the dense one due to the larger amount of water to be evaporated during the falling rate.
Abstract: Synthetic oily wastewaters were prepared from metal working fluids (MWF). Electrocoagulation experiments were performed under constant voltage application. The current, conductivity, pH, dissolved oxygen concentration and temperature were recorded on line at every 5 seconds during the experiments. Effects of applied voltage differences, electrode materials and distance between electrodes on removal efficiency have been investigated. According to the experimental results, the treatment of MWF wastewaters by iron electrodes rather than aluminum and stainless steel was much quicker; and the distance between electrodes should be less than 1cm. The electrocoagulation process was modeled by using block oriented approach and found out that it can be modeled as a single input and multiple output system. Modeling studies indicates that the electrocoagulation process has a nonlinear model structure.
Abstract: E-government is becoming more important these days. However, the adoption of e-government is often slowed down by technical and non-technical security factors. Nowadays, there many security models that can make the e-government services more secure. This paper will explain the main security factors that affected the level of e-government security. Moreover, it will also analyse current existing models. Finally, the paper will suggest a comprehensive security model that will contain most of technical and non-technical factors.
Abstract: Combustion of fuels in industrial and transport sector has lead to an alarming release of polluting gases to the atmosphere. Carbon monoxide is one such pollutant, which is formed as a result of incomplete oxidation of the fuel. In order to analyze the effect of catalyst on the reduction of CO emissions to the atmosphere, two catalysts Mn2O3 and Hopcalite are considered. A model was formed based on mass and energy balance equations. Results show that Hopcalite catalyst as compared to Mn2O3 catalyst helped in faster conversion of the polluting gas as the operating temperature of the hopcalite catalyst is much lower as compared to the operating temperature of Mn2O3 catalyst.
Abstract: It can be determined in preference between
representative mechanical and mathematical model of elasticcreeping
deformation of transversally isotropic array with doubly
periodic system of tilted slots, and offer of the finite elements
calculation scheme, and inspection of the states of two diagonal
arbitrary profile cavities of deep inception, and in setting up the tense
and dislocation fields distribution nature in computing processes.
Abstract: The mathematical equation for Separation of the
binary aqueous solution is developed by using the Spiegler- Kedem
theory. The characteristics of a B-9 hollow fibre module of Du Pont
are determined by using these equations and their results are
compared with the experimental results of Ohya et al. The agreement
between these results is found to be excellent.
Abstract: Code mobility technologies attract more and more developers and consumers. Numerous domains are concerned, many platforms are developed and interest applications are realized. However, developing good software products requires modeling, analyzing and proving steps. The choice of models and modeling languages is so critical on these steps. Formal tools are powerful in analyzing and proving steps. However, poorness of classical modeling language to model mobility requires proposition of new models. The objective of this paper is to provide a specific formalism “Coloured Reconfigurable Nets" and to show how this one seems to be adequate to model different kinds of code mobility.
Abstract: Over the early years of the 21st century, cities
throughout the Middle East, particularly in the Gulf region have
expanded more rapidly than ever before. Given the presence of a
large volume of high-rise buildings allover the region, the local
authority aims to set a new standard for sustainable development;
with an integrated approach to maintain a balance between economy,
quality, environmental protection and safety of life. In the very near
future, as mandatory requirements, sustainability will be the criteria
that should be included in all building projects. It is well known in
the building sustainability topics that structural design engineers do
not have a key role in this matter. In addition, the LEED (Leadership
in Energy and Environmental Design) has looked almost exclusively
on the environmental components and materials specifications. The
objective of this paper is to focus and establish groundwork for
sustainability techniques and applications related to the RC high-rise
buildings design, from the structural point of view. A set of
recommendations related to local conditions, structural modeling and
analysis is given, and some helpful suggestions for structural design
team work are addressed. This paper attempts to help structural
engineers in identifying the building sustainability design, in order to
meet local needs and achieve alternative solutions at an early stage of
project design.
Abstract: Devices in a pervasive computing system (PCS) are characterized by their context-awareness. It permits them to provide proactively adapted services to the user and applications. To do so, context must be well understood and modeled in an appropriate form which enhance its sharing between devices and provide a high level of abstraction. The most interesting methods for modeling context are those based on ontology however the majority of the proposed methods fail in proposing a generic ontology for context which limit their usability and keep them specific to a particular domain. The adaptation task must be done automatically and without an explicit intervention of the user. Devices of a PCS must acquire some intelligence which permits them to sense the current context and trigger the appropriate service or provide a service in a better suitable form. In this paper we will propose a generic service ontology for context modeling and a context-aware service adaptation based on a service oriented definition of context.
Abstract: In this paper, modeling of an acoustic enclosed
vehicle cabin has been carried out by using boundary element
method. Also, the second purpose of this study is analyzing of linear
wave equation in an acoustic field. The resultants of this modeling
consist of natural frequencies that have been compared with
resultants derived from finite element method. By using numerical
method (boundary element method) and after solution of wave
equation inside an acoustic enclosed cabin, this method has been
progressed to simulate noise inside a simple vehicle cabin.
Abstract: Grasslands of Iran are encountered with a vast
desertification and destruction. Some legumes are plants of forage
importance with high palatability. Studied legumes in this project are
Onobrychis, Medicago sativa (alfalfa) and Trifolium repens. Seeds
were cultivated in research field of Kaboutarabad (33 km East of
Isfahan, Iran) with an average 80 mm. annual rainfall. Plants were
cultivated in a split plot design with 3 replicate and two water
treatments (weekly irrigation, and under stress with same amount per
15 days interval). Water entrance to each plots were measured by
Partial flow. This project lasted 20 weeks. Destructive samplings
(1m2 each time) were done weekly. At each sampling plants were
gathered and weighed separately for each vegetative parts. An Area
Meter (Vista) was used to measure root surface and leaf area. Total
shoot and root fresh and dry weight, leaf area index and soil coverage
were evaluated too. Dry weight was achieved in 750c oven after 24
hours. Statgraphic and Harvard Graphic software were used to
formulate and demonstrate the parameters curves due to time. Our
results show that Trifolium repens has affected 60 % and Medicago
sativa 18% by water stress. Onobrychis total fresh weight was
reduced 45%. Dry weight or Biomass in alfalfa is not so affected by
water shortage. This means that in alfalfa fields we can decrease the
irrigation amount and have some how same amount of Biomass.
Onobrychis show a drastic decrease in Biomass. The increases in
total dry matter due to time in studied plants are formulated. For
Trifolium repens if removal or cattle entrance to meadows do not
occurred at perfect time, it will decrease the palatability and water
content of the shoots. Water stress in a short period could develop the
root system in Trifolium repens, but if it last more than this other
ecological and soil factors will affect the growth of this plant. Low
level of soil water is not so important for studied legume forges. But
water shortage affect palatability and water content of aerial parts.
Leaf area due to time in studied legumes is formulated. In fact leaf
area is decreased by shortage in available water. Higher leaf area
means higher forage and biomass production. Medicago and
Onobrychis reach to the maximum leaf area sooner than Trifolium
and are able to produce an optimum soil cover and inhibit the
transpiration of soil water of meadows. Correlation of root surface to
Total biomass in studied plants is formulated. Medicago under water
stress show a 40% decrease in crown cover while at optimum
condition this amount reach to 100%. In order to produce forage in
areas without soil erosion Medicago is the best choice even with a
shortage in water resources. It is tried to represent the growth
simulation of three famous Forage Legumes. By growth simulation
farmers and range managers could better decide to choose best plant
adapted to water availability without designing different time and
labor consuming field experiments.
Abstract: This paper presents a simple three phase power flow
method for solution of three-phase unbalanced radial distribution
system (RDN) with voltage dependent loads. It solves a simple
algebraic recursive expression of voltage magnitude, and all the data
are stored in vector form. The algorithm uses basic principles of
circuit theory and can be easily understood. Mutual coupling between
the phases has been included in the mathematical model. The
proposed algorithm has been tested with several unbalanced radial
distribution networks and the results are presented in the article. 8-
bus and IEEE 13 bus unbalanced radial distribution system results
are in agreements with the literature and show that the proposed
model is valid and reliable.
Abstract: Microscopic emission and fuel consumption models
have been widely recognized as an effective method to quantify real
traffic emission and energy consumption when they are applied with
microscopic traffic simulation models. This paper presents a
framework for developing the Microscopic Emission (HC, CO, NOx,
and CO2) and Fuel consumption (MEF) models for light-duty
vehicles. The variable of composite acceleration is introduced into
the MEF model with the purpose of capturing the effects of historical
accelerations interacting with current speed on emission and fuel
consumption. The MEF model is calibrated by multivariate
least-squares method for two types of light-duty vehicle using
on-board data collected in Beijing, China by a Portable Emission
Measurement System (PEMS). The instantaneous validation results
shows the MEF model performs better with lower Mean Absolute
Percentage Error (MAPE) compared to other two models. Moreover,
the aggregate validation results tells the MEF model produces
reasonable estimations compared to actual measurements with
prediction errors within 12%, 10%, 19%, and 9% for HC, CO, NOx
emissions and fuel consumption, respectively.
Abstract: Reliable water level forecasts are particularly
important for warning against dangerous flood and inundation. The
current study aims at investigating the suitability of the adaptive
network based fuzzy inference system for continuous water level
modeling. A hybrid learning algorithm, which combines the least
square method and the back propagation algorithm, is used to
identify the parameters of the network. For this study, water levels
data are available for a hydrological year of 2002 with a sampling
interval of 1-hour. The number of antecedent water level that should
be included in the input variables is determined by two statistical
methods, i.e. autocorrelation function and partial autocorrelation
function between the variables. Forecasting was done for 1-hour until
12-hour ahead in order to compare the models generalization at
higher horizons. The results demonstrate that the adaptive networkbased
fuzzy inference system model can be applied successfully and
provide high accuracy and reliability for river water level estimation.
In general, the adaptive network-based fuzzy inference system
provides accurate and reliable water level prediction for 1-hour ahead
where the MAPE=1.15% and correlation=0.98 was achieved. Up to
12-hour ahead prediction, the model still shows relatively good
performance where the error of prediction resulted was less than
9.65%. The information gathered from the preliminary results
provide a useful guidance or reference for flood early warning
system design in which the magnitude and the timing of a potential
extreme flood are indicated.
Abstract: The orthogonal processes to shape the triangle steel plate into a equilateral vertical steel are examined by an incremental elasto-plastic finite-element method based on an updated Lagrangian formulation. The highly non-linear problems due to the geometric changes, the inelastic constitutive behavior and the boundary conditions varied with deformation are taken into account in an incremental manner. On the contact boundary, a modified Coulomb friction mode is specially considered. A weighting factor r-minimum is employed to limit the step size of loading increment to linear relation. In particular, selective reduced integration was adopted to formulate the stiffness matrix. The simulated geometries of verticality could clearly demonstrate the vertical processes until unloading. A series of experiments and simulations were performed to validate the formulation in the theory, leading to the development of the computer codes. The whole deformation history and the distribution of stress, strain and thickness during the forming process were obtained by carefully considering the moving boundary condition in the finite-element method. Therefore, this modeling can be used for judging whether a equilateral vertical steel can be shaped successfully. The present work may be expected to improve the understanding of the formation of the equilateral vertical steel.
Abstract: The purpose of this paper is to examine the inter
relationships among various leadership branding constructs of
entrepreneurs in small and medium sized enterprises (SMEs). We
employ a quantitative structural equation modeling through a new
leadership branding engagement model comprises constructs of
leader-s or entrepreneur-s personality, branding practice and
customer engagement. The results confirm that there are significant
relationships between the three constructs and the major fit indices
indicate that the data fits the proposed model. The findings provide
insights and fill in the literature gaps on statistically validated
representation of leadership branding for SMEs across new economic
regions of Malaysia that may implicate other economic zones with
similar situations. This study extends the establishment of a
leadership branding engagement model with a new mechanism of
using leaders- personality as a predictor to branding practice and
customer engagement performance.
Abstract: As the advancement of technology, online shopping channel develops rapidly in recent years. According to the report of Taiwan Network Information Center, there are almost eighty percents of internet population shopping in online channel. Synthesizing insights from the previous research, this study develops the conceptual model to integrate Theory of Perceived Risk (TPR) and Technology Acceptance Model (TAM) to apply in online shopping. Using data collected from 637 respondents from online survey website, we use structural equation modeling to test measurement and structural models. The results suggest the need for consideration of perceived risk as an antecedent in the Technology Acceptance Model. The limitations and implications are discussed.
Abstract: Optimization of a microwave-assisted extraction of cherry laurel (Prunus laurocerasus) fruit using methanol was studied. The influence of process parameters (microwave power, plant material-to-solvent ratio and the extraction time) on the extraction efficiency were optimized by using response surface methodology. The predicted maximum yield of extractive substances (41.85 g/100 g fresh plant material) was obtained at microwave power of 600 W and plant material to solvent ratio of 0.2 g/cm3 after 26 minutes of extraction, while a mean value of 40.80±0.41 g/100 g fresh plant material was obtained from laboratory experiments. This proves applicability of the model in predicting optimal extraction conditions with minimal laborious and time consuming. The results indicated that all process parameters were effective on the extraction efficiency, while the most important factor was extraction time. In order to rationalize production the optimal economical condition which gave a large total extract yield with minimal energy and solvent consumption was found.