Abstract: In this paper are illustrated the principal aspects
connected with the numerical evaluation of thermal stress induced by high gradient temperature in the concrete beam. The reinforced concrete beam has many advantages over steel
beam, such as high resistance to high temperature, high resistance to thermal shock, Better resistance to fatigue and buckling, strong
resistance against, fire, explosion, etc.
The main drawback of the reinforced concrete beam is its poor resistance to tensile stresses. In order to investigate the thermal
induced tensile stresses, a numerical model of a transient thermal
analysis is presented for the evaluation of thermo-mechanical
response of concrete beam to the high temperature, taking into account the temperature dependence of the thermo physical properties of the concrete like thermal conductivity and specific heat.
Abstract: In the real application of active control systems to
mitigate the response of structures subjected to sever external
excitations such as earthquake and wind induced vibrations, since the
capacity of actuators is limited then the actuators saturate. Hence, in
designing controllers for linear and nonlinear structures under sever
earthquakes, the actuator saturation should be considered as a
constraint. In this paper optimal design of active controllers for
nonlinear structures by considering the actuator saturation has been
studied. To this end a method has been proposed based on defining
an optimization problem which considers the minimizing of the
maximum displacement of the structure as objective when a limited
capacity for actuator has been used as a constraint in optimization
problem. To evaluate the effectiveness of the proposed method, a
single degree of freedom (SDF) structure with a bilinear hysteretic
behavior has been simulated under a white noise ground acceleration
of different amplitudes. Active tendon control mechanism, comprised
of pre-stressed tendons and an actuator, and extended nonlinear
Newmark method based instantaneous optimal control algorithm
have been used as active control mechanism and algorithm. To
enhance the efficiency of the controllers, the weights corresponding
to displacement, velocity, acceleration and control force in the
performance index have been found by using the Distributed Genetic
Algorithm (DGA). According to the results it has been concluded
that the proposed method has been effective in considering the
actuator saturation in designing optimal controllers for nonlinear
frames. Also it has been shown that the actuator capacity and the
average value of required control force are two important factors in
designing nonlinear controllers for considering the actuator
saturation.
Abstract: The hydromagnetic flow of a Maxwell fluid past a vertical stretching sheet with thermophoresis is considered. The impact of chemical reaction species to the flow is analyzed for the first time by using the homotopy analysis method (HAM). The h-curves for the flow boundary layer equations are presented graphically. Several values of wall skin friction, heat and mass transfer are obtained and discussed.
Abstract: The successful use of CDMA technology is based on
the construction of large families of encoding sequences with good
correlation properties. This paper discusses PN sequence generation
based on Residue Arithmetic with an effort to improve the performance
of existing interference-limited CDMA technology for mobile
cellular systems. All spreading codes with residual number system
proposed earlier did not consider external interferences, multipath
propagation, Doppler effect etc. In literature the use of residual
arithmetic in DS-CDMA was restricted to encoding of already spread
sequence; where spreading of sequence is done by some existing
techniques. The novelty of this paper is the use of residual number
system in generation of the PN sequences which is used to spread
the message signal. The significance of cross-correlation factor in
alleviating multi-access interference is also discussed. The RNS based
PN sequence has superior performance than most of the existing
codes that are widely used in DS-CDMA applications. Simulation
results suggest that the performance of the proposed system is
superior to many existing systems.
Abstract: Many medical devices are driven by motor pumps. Some researchers reported that the vibration mainly affected medical devices using a motor pump. The purpose of this study was to examine the effect of stiffness and damping coefficient in a 3-dimensional (3D) model of a motor pump and spring. In the present paper, experimental and mathematical tests for the moments of inertia of the 3D model and the material properties were investigated by an INSTRON machine. The response surfaces could be generated by using 3D multi-body analysis and the design of experiment method. It showed that differences in contours of the response surface were clearly found for the particular area. Displacement of the center of the motor pump was decreased at K≈2000 N/M, C≈12.5 N-sec/M. However, the frequency was increased at K≈2000 N/M, C≈15 N-sec/M. In this study, this study suggested experimental technique for vibration reduction for a motor pump in medical device. The combined method suggested in this study will greatly contribute to design of medical devices concerning vibration and noise intervention.
Abstract: Due to the non- intuitive nature of Quantum
algorithms, it becomes difficult for a classically trained person to
efficiently construct new ones. So rather than designing new
algorithms manually, lately, Genetic algorithms (GA) are being
implemented for this purpose. GA is a technique to automatically
solve a problem using principles of Darwinian evolution. This has
been implemented to explore the possibility of evolving an n-qubit
circuit when the circuit matrix has been provided using a set of
single, two and three qubit gates. Using a variable length population
and universal stochastic selection procedure, a number of possible
solution circuits, with different number of gates can be obtained for
the same input matrix during different runs of GA. The given
algorithm has also been successfully implemented to obtain two and
three qubit Boolean circuits using Quantum gates. The results
demonstrate the effectiveness of the GA procedure even when the
search spaces are large.
Abstract: Nowadays over-consumption of fossil energy in
buildings especially in residential buildings and also considering the
increase in populations, the crisis of energy shortage in a near future
is predictable. The recent performance of developed countries in
construction with the aim of decreasing fossil energies shows that
these countries have understood the incoming crisis and has taken
reasonable and basic actions in this regard. However, Iranian
architecture, with several thousands years of history, has acquired
and executed invaluable experiences in designing, adapting and
coordinating with the nature.
Architectural studies during the recent decades show that imitating
modern western architecture results in high energy wastage beside
the fact that it not reasonably adaptable and corresponded with the
habits and customs of people unlike the architecture in the past which
was compatible and adaptable with the climatic conditions and this
necessitates optimal using of renewable energies more than ever. This
paper studies problems of design, execution and living in today's
houses and reviews the characteristics of climatic elements paying
special attention to the performance of trombe wall and solar
greenhouse in traditional houses and offers some suggestions for
combining these two elements and a climatic strategy.
Abstract: Lurking behavior is common in information-seeking oriented communities. Transferring users with lurking behavior to be contributors can assist virtual communities to obtain competitive advantages. Based on the ecological cognition framework, this study proposes a model to examine the antecedents of lurking behavior in information-seeking oriented virtual communities. This study argues desire for emotional support, desire for information support, desire for performance-approach, desire for performance -avoidance, desire for mastery-approach, desire for mastery-avoidance, desire for ability trust, desire for benevolence trust, and desire for integrity trust effect on lurking behavior. This study offers an approach to understanding the determinants of lurking behavior in online contexts.
Abstract: Histogram plays an important statistical role in digital
image processing. However, the existing quantum image models are
deficient to do this kind of image statistical processing because
different gray scales are not distinguishable. In this paper, a novel
quantum image representation model is proposed firstly in which the
pixels with different gray scales can be distinguished and operated
simultaneously. Based on the new model, a fast quantum algorithm of
constructing histogram for quantum image is designed. Performance
comparison reveals that the new quantum algorithm could achieve an
approximately quadratic speedup than the classical counterpart. The
proposed quantum model and algorithm have significant meanings for
the future researches of quantum image processing.
Abstract: An adaptive Helmholtz resonator was designed and
adapted to hydraulics. The resonator was controlled by open- and
closed-loop controls so that 20 dB attenuation of the peak-to-peak
value of the pulsating pressure was maintained. The closed-loop
control was noted to be better, albeit it was slower because of its low
pressure and temperature variation, which caused variation in the
effective bulk modulus of the hydraulic system. Low-pressure
hydraulics contains air, which affects the stiffness of the hydraulics,
and temperature variation changes the viscosity of the oil. Thus, an
open-loop control loses its efficiency if a condition such as
temperature or the amount of air changes after calibration. The
instability of the low-pressure hydraulic system reduced the
operational frequency range of the Helmholtz resonator when
compared with the results of an analytical model.
Different dampers for hydraulics are presented. Then analytical
models of a hydraulic pipe and a hydraulic pipe with a Helmholtz
resonator are presented. The analytical models are based on the wave
equation of sound pressure. Finally, control methods and the results
of experiments are presented.
Abstract: In this paper, a new reverse converter for the moduli set {2n, 2n–1, 2n–1–1} is presented. We improved a previously introduced conversion algorithm for deriving an efficient hardware design for reverse converter. Hardware architecture of the proposed converter is based on carry-save adders and regular binary adders, without the requirement for modular adders. The presented design is faster than the latest introduced reverse converter for moduli set {2n, 2n–1, 2n–1–1}. Also, it has better performance than the reverse converters for the recently introduced moduli set {2n+1–1, 2n, 2n–1}
Abstract: In this paper, we apply the FM methodology to the
cross-section of Romanian-listed common stocks and investigate the
explanatory power of market beta on the cross-section of commons
stock returns from Bucharest Stock Exchange. Various assumptions
are empirically tested, such us linearity, market efficiency, the “no
systematic effect of non-beta risk" hypothesis or the positive
expected risk-return trade-off hypothesis. We find that the Romanian
stock market shows the same properties as the other emerging
markets in terms of efficiency and significance of the linear riskreturn
models. Our analysis included weekly returns from January
2002 until May 2010 and the portfolio formation, estimation and
testing was performed in a rolling manner using 51 observations (one
year) for each stage of the analysis.
Abstract: This current research focused on development of degradable starch based packaging film with enhanced mechanical properties. A series of low density polyethylene (LDPE)/tapioca starch compounds with various tapioca starch contents were prepared by twin screw extrusion with the addition of maleic anhydride grafted polyethylene as compatibilizer. Palm cooking oil was used as processing aid to ease the blown film process, thus, degradable film can be processed via conventional blown film machine. Studies on their characteristics, mechanical properties and biodegradation were carried out by Fourier Transform Infrared (FTIR) spectroscopy and optical properties, tensile test and exposure to fungi environment respectively. The presence of high starch contents had an adverse effect on the tensile properties of LDPE/tapioca starch blends. However, the addition of compatibilizer to the blends improved the interfacial adhesion between the two materials, hence, improved the tensile properties of the films. High content of starch amount also was found to increase the rate of biodegradability of LDPE/tapioca starch films. It can be proved by exposure of the film to fungi environment. A growth of microbes colony can be seen on the surface of LDPE/tapioca starch film indicates that the granular starch present on the surface of the polymer film is attacked by microorganisms, until most of it is assimilated as a carbon source.
Abstract: An efficient parallel form in digital signal processor can improve the algorithm performance. The butterfly structure is an important role in fast Fourier transform (FFT), because its symmetry form is suitable for hardware implementation. Although it can perform a symmetric structure, the performance will be reduced under the data-dependent flow characteristic. Even though recent research which call as novel memory reference reduction methods (NMRRM) for FFT focus on reduce memory reference in twiddle factor, the data-dependent property still exists. In this paper, we propose a parallel-computing approach for FFT implementation on digital signal processor (DSP) which is based on data-independent property and still hold the property of low-memory reference. The proposed method combines final two steps in NMRRM FFT to perform a novel data-independent structure, besides it is very suitable for multi-operation-unit digital signal processor and dual-core system. We have applied the proposed method of radix-2 FFT algorithm in low memory reference on TI TMSC320C64x DSP. Experimental results show the method can reduce 33.8% clock cycles comparing with the NMRRM FFT implementation and keep the low-memory reference property.
Abstract: Electrical resistivity is a fundamental parameter of metals or electrical conductors. Since resistivity is a function of temperature, in order to completely understand the behavior of metals, a temperature dependent theoretical model is needed. A model based on physics principles has recently been developed to obtain an equation that relates electrical resistivity to temperature. This equation is dependent upon a parameter associated with the electron travel time before being scattered, and a parameter that relates the energy of the atoms and their separation distance. Analysis of the energy parameter reveals that the equation is optimized if the proportionality term in the equation is not constant but varies over the temperature range. Additional analysis reveals that the theoretical equation can be used to determine the mean free path of conduction electrons, the number of defects in the atomic lattice, and the ‘equivalent’ charge associated with the metallic bonding of the atoms. All of this analysis provides validation for the theoretical model and provides insight into the behavior of metals where performance is affected by temperatures (e.g., integrated circuits and temperature sensors).
Abstract: This paper presents the design and implementation of a fully integrated transimpedance amplifier (TIA) as the analog frontend receiver for Capacitive Micromachined Ultrasound Transducers (CMUTs) for ultrasound biomicroscope imaging application. The amplifier is designed to amplify the received signals from 17.5MHz to 52.5MHz with a center frequency of 35MHz. The TIA was fabricated in GF 0.18μm 1P6M 30V high voltage process. The measurement results show that the designed amplifier can reach a transimpedance gain of 61.08dBΩ and operating frequency from 17.5MHz to 100MHz with 1VP-P output voltage under 6V power supply.
Abstract: User interaction components of Augmented Reality (AR) systems have to be tested with users in order to find and fix usability problems as early as possible. In this paper we will report on a user-centered design approach for AR systems following the experience acquired during the design and evaluation of a software prototype for an AR-based educational platform. In this respect we will focus on the re-design of the user task based on the results from a formative usability evaluation. The basic idea of our approach is to describe task scenarios in a tabular format, to develop a task model in a task modeling environment and then to simulate the execution.
Abstract: CFD simulations are carried out in arterial stenoses
with 48 % areal occlusion. Non-newtonian fluid model is selected for
the blood flow as the same problem has been solved before with
Newtonian fluid model. Studies on flow resistance with the presence
of surface irregularities are carried out. Investigations are also
performed on the pressure drop at various Reynolds numbers. The
present study revealed that the pressure drop across a stenosed artery
is practically unaffected by surface irregularities at low Reynolds
numbers, while flow features are observed and discussed at higher
Reynolds numbers.
Abstract: This paper presents a set of guidelines for the design
of multi-user awareness systems. In a first step, general requirements
for team awareness systems are analyzed. In the second part of the
paper, the identified requirements are aggregated and transformed
into concrete design guidelines for the development of team
awareness systems.
Abstract: A control system design with Characteristic Ratio
Assignment (CRA) is proven that effective for SISO control design.
But the control system design for MIMO via CRA is not concrete
procedure. In this paper presents the control system design method
for quadruple-tank process via CRA. By using the decentralized
method for both minimum phase and non-minimum phase are made.
The results from PI and PID controller design via CRA can be
illustrated the validity of our approach by MATLAB.