Abstract: The impact of a proposed pier on tidal current
alteration was evaluated. The proposed pier location was in Salad
Bay on Koa Kood Island, Trat province, Thailand, and was designed
to accommodate passenger ships with a draft of less than 2 m. The
study began with collecting necessary data, including bathymetric,
water elevation and tidal current characteristics. The impact was
assessed using a software package (MIKE21). Although the results
showed that the pier would affect the existing current pattern, the
change was determined to be insignificant, as the design of the piles
for the pier provided sufficient spacing to let the current flow as
freely as possible. Consequences of the altered current, such as
seabed erosion, water stagnation, sediment deposition and
navigational risk were assessed. Environmental mitigation measures
might be necessary if the impacts were considered unacceptable.
Abstract: Subcritical water extraction was investigated as a
novel and alternative technology in the food and pharmaceutical
industry for the separation of Mannitol from olive leaves and its
results was compared with those of Soxhlet extraction. The effects of
temperature, pressure, and flow rate of water and also momentum
and mass transfer dimensionless variables such as Reynolds and
Peclet Numbers on extraction yield and equilibrium partition
coefficient were investigated. The 30-110 bars, 60-150°C, and flow
rates of 0.2-2 mL/min were the water operating conditions. The
results revealed that the highest Mannitol yield was obtained at
100°C and 50 bars. However, extraction of Mannitol was not
influenced by the variations of flow rate. The mathematical modeling
of experimental measurements was also investigated and the model is
capable of predicting the experimental measurements very well. In
addition, the results indicated higher extraction yield for the
subcritical water extraction in contrast to Soxhlet method.
Abstract: This study was conducted to investigate the efficacy
of five herbicides on narrow leaved weeds and growth and yield of
wheat. An experiment was conducted at Agronomic Research
Farm, University of Agriculture Faisalabad. The experiment was
laid out in randomized complete block designee (RCBD) with three
replications. Treatments studied were clodinafop (Topic-15 WG) at
37 g a.i. ha-1, clodinafop (Topaz-15 WG) at 45 g a.i. ha-1,
fenoxaprop-p-ethyl (Puma Super-75 EW) at 45 g a.i. ha-1,
fenoxaprop-p-ethyl (Gramicide-6.9 EW) at 85 g a.i. ha-1,
fenoxaprop-p-ethyl (Chinlima-6.9 EW) at 85 g a.i. ha-1 and weedy
check. Plots treated with fenoxaprop-p-ethyl (Puma Super-75 EW)
at 45 g a.i. ha-1 produced relatively less weed biomass, more plant
height, number of spike bearing tillers, number of grains per spike,
1000-grain weight and grain yield (4.20 t ha-1).
Abstract: This paper provides an exergy analysis of the multistage refrigeration cycle used for C2+ recovery plant. The behavior of an industrial refrigeration cycle with refrigerant propane has been investigated by the exergy method. A computational model based on the exergy analysis is presented for the investigation of the effects of the valves on the exergy losses, the second law of efficiency, and the coefficient of performance (COP) of a vapor compression refrigeration cycle. The equations of exergy destruction and exergetic efficiency for the main cycle components such as evaporators, condensers, compressors, and expansion valves are developed. The relations for the total exergy destruction in the cycle and the cycle exergetic efficiency are obtained. An ethane recovery unit with its refrigeration cycle has been simulated to prepare the exergy analysis. Using a typical actual work input value; the exergetic efficiency of the refrigeration cycle is determined to be 39.90% indicating a great potential for improvements. The simulation results reveal that the exergetic efficiencies of the heat exchanger and expansion sections get the lowest rank among the other compartments of refrigeration cycle. Refrigeration calculations have been carried out through the analysis of T–S and P–H diagrams where coefficient of performance (COP) was obtained as 1.85. The novelty of this article includes the effect and sensitivity analysis of molar flow, pressure drops and temperature on the exergy efficiency and coefficient of performance of the cycle.
Abstract: With the presence of a uniform vertical magnetic field and suspended particles, thermocapillary instability in a horizontal liquid layer is investigated. The resulting eigenvalue is solved by the Galerkin technique for various basic temperature gradients. It is found that the presence of magnetic field always has a stability effect of increasing the critical Marangoni number.
Abstract: Nonlinear finite element method and Serendipity eight
nodes element are used for determining of ground surface settlement
due to tunneling. Linear element with elastic behavior is used for
modeling of lining. Modified Generalized plasticity model with nonassociated
flow rule is applied for analysis of a tunnel in Sao Paulo –
Brazil. The tunnel had analyzed by Lades- model with 16 parameters.
In this work modified Generalized Plasticity is used with 10
parameters, also Mohr-Coulomb model is used to analysis the tunnel.
The results show good agreement with observed results of field data
by modified Generalized Plasticity model than other models. The
obtained result by Mohr-Coulomb model shows less settlement than
other model due to excavation.
Abstract: Sensors have been used in various kinds of academic
fields and applications. In this article, we propose the idea of
modularized sensors that combine multiple sensor modules into a
unique sensor. We divide a sensor into several units according to
functionalities. Each unit has different sensor modules, which share
the same type of connectors and can be serially and arbitrarily
connected each other. A user can combine different sensor modules
into a sensor platform according to requirements. Compared with
current modularized sensors, the proposed sensor platform is highly
flexible and reusable. We have implemented the prototype of the
proposed sensor platform, and the experimental results show the
proposed platform can work correctly.
Abstract: A novel algorithm for construct a seamless video mosaic of the entire panorama continuously by automatically analyzing and managing feature points, including management of quantity and quality, from the sequence is presented. Since a video contains significant redundancy, so that not all consecutive video images are required to create a mosaic. Only some key images need to be selected. Meanwhile, feature-based methods for mosaicing rely on correction of feature points? correspondence deeply, and if the key images have large frame interval, the mosaic will often be interrupted by the scarcity of corresponding feature points. A unique character of the method is its ability to handle all the problems above in video mosaicing. Experiments have been performed under various conditions, the results show that our method could achieve fast and accurate video mosaic construction. Keywords?video mosaic, feature points management, homography estimation.
Abstract: Dual bell nozzle is a promising one among the altitude
adaptation nozzle concepts, which offer increased nozzle
performance in rocket engines. Its advantage is the simplicity it offers
due to the absence of any additional mechanical device or movable
parts. Hence it offers reliability along with improved nozzle
performance as demanded by future launch vehicles. Among other
issues, the flow transition to the extension nozzle of a dual bell
nozzle is one of the major issues being studied in the development of
dual bell nozzle. A parameter named over-expansion factor, which
controls the value of the wall inflection angle, has been reported to
have substantial influence in this transition process. This paper
studies, through CFD and cold flow experiments, the effect of overexpansion
factor on flow transition in dual bell nozzles.
Abstract: In determining the electromagnetic properties of
magnetic materials, hysteresis modeling is of high importance. Many
models are available to investigate those characteristics but they tend
to be complex and difficult to implement. In this paper a new
qualitative hysteresis model for ferromagnetic core is presented,
based on the function approximation capabilities of adaptive neuro
fuzzy inference system (ANFIS). The proposed ANFIS model
combined the neural network adaptive capabilities and the fuzzy
logic qualitative approach can restored the hysteresis curve with a
little RMS error. The model accuracy is good and can be easily
adapted to the requirements of the application by extending or
reducing the network training set and thus the required amount of
measurement data.
Abstract: The alterations in pancreas gland secretion hormones
following an aerobic and exhausting exercise was the purpose of this
study. Sixteen healthy men participated in the study. The blood
samples of these participants were taken in four stages under fasting
condition. The first sample was taken before Bruce exhausting and
aerobic test, the second sample was taken after Bruce exercise and
the third and forth stages samples were taken 24 and 48 hours after
the exercises respectively. The final results indicated that a strenuous
aerobic exercise can have a significant effect on glucagon and insulin
concentration of blood serum. The increase in blood serum insulin
was higher after 24 and 48 hours. It seems that an intensive exercise
has little effect on changes in glucagon concentration of blood serum.
Also, disorder in secretion in glucagon and insulin concentration of
serum disturbs athletes- exercise.
Abstract: Electronic nose (array of chemical sensors) are widely
used in food industry and pollution control. Also it could be used to
locate or detect the direction of the source of emission odors. Usually
this task is performed by electronic nose (ENose) cooperated with
mobile vehicles, but when a source is instantaneous or surrounding is
hard for vehicles to reach, problem occurs. Thus a method for
stationary ENose to detect the direction of the source and locate the
source will be required. A novel method which uses the ratio between
the responses of different sensors as a discriminant to determine the
direction of source in natural wind surroundings is presented in this
paper. The result shows that the method is accurate and easily to be
implemented. This method could be also used in movably, as an
optimized algorithm for robot tracking source location.
Abstract: Robust nonlinear integrated navigation of GPS and
low cost MEMS is a hot topic of research these days. A robust filter
is required to cope up with the problem of unpredictable
discontinuities and colored noises associated with low cost sensors.
H∞ filter is previously used in Extended Kalman filter and Unscented
Kalman filter frame. Unscented Kalman filter has a problem of
Cholesky matrix factorization at each step which is a very unstable
operation. To avoid this problem in this research H∞ filter is
designed in Square root Unscented filter framework and found 50%
more robust towards increased level of colored noises.
Abstract: The paper presents the design of a mini-UAV attitude
controller using the backstepping method. Starting from the nonlinear
dynamic equations of the mini-UAV, by using the backstepping
method, the author of this paper obtained the expressions of the
elevator, rudder and aileron deflections, which stabilize the UAV, at
each moment, to the desired values of the attitude angles. The attitude
controller controls the attitude angles, the angular rates, the angular
accelerations and other variables that describe the UAV longitudinal
and lateral motions. To design the nonlinear controller, by using the
backstepping technique, the nonlinear equations and the Lyapunov
analysis have been directly used. The designed controller has been
implemented in Matlab/Simulink environment and its effectiveness
has been tested with a campaign of numerical simulations using data
from the UAV flight tests. The obtained results are very good and
they are better than the ones found in previous works.
Abstract: In this study, fuzzy rule-based classifier is used for the
diagnosis of congenital heart disease. Congenital heart diseases are
defined as structural or functional heart disease. Medical data sets
were obtained from Pediatric Cardiology Department at Selcuk
University, from years 2000 to 2003. Firstly, fuzzy rules were
generated by using medical data. Then the weights of fuzzy rules
were calculated. Two different reasoning methods as “weighted vote
method" and “singles winner method" were used in this study. The
results of fuzzy classifiers were compared.
Abstract: In this study the elastic-plastic stress distribution in
weld-bonded joint, fabricated from austenitic stainless steel (AISI
304) sheet of 1.00 mm thickness and Epoxy adhesive Araldite 2011,
subjected to axial loading is investigated. This is needed to improve
design procedures and welding codes, and saving efforts in the
cumbersome experiments and analysis. Therefore, a complete 3-D
finite element modelling and analysis of spot welded, bonded and
weld-bonded joints under axial loading conditions is carried out. A
comprehensive systematic experimental program is conducted to
determine many properties and quantities, of the base metals and the
adhesive, needed for FE modelling, such like the elastic – plastic
properties, modulus of elasticity, fracture limit, the nugget and heat
affected zones (HAZ) properties, etc. Consequently, the finite
element models developed, for each case, are used to evaluate
stresses distributions across the entire joint, in both the elastic and
plastic regions. The stress distribution curves are obtained,
particularly in the elastic regions and found to be consistent and in
excellent agreement with the published data. Furthermore, the
stresses distributions are obtained in the weld-bonded joint and
display the best results with almost uniform smooth distribution
compared to spot and bonded cases. The stress concentration peaks at
the edges of the weld-bonded region, are almost eliminated resulting
in achieving the strongest joint of all processes.
Abstract: Our results showed that treatment with both
cyclooxygenase (COX1 or COX2) inhibitors impair reproduction
parameters of the medaka. Resveratrol (COX1 inhibitor) caused an
decrease in the number of spawning females at the first week of
feeding fish with experimental diets. In the group treated with NS-
398 (COX2 inhibitor) we found the lowest sperm velocity parameters
and decreased linearity of movement. The ovaries of the medaka fed
feed supplemented with Resveratrol or NS-398 were confirmed to
have a lower share of matured oocytes however during the
experiment (four weeks) the number of eggs spawned by females was
similar. Both inhibitors in fish diet (20 mg/kg body weight/day)
caused a decrease in the embryo survival. Our results revealed that
for the medaka female reproduction, activity of both COX enzymes
might be necessary whereas males reproduction competence, as
expressed by sperm motility parameters, might be related to COX2
activity.
Abstract: This paper describes the development of a WLAN
propagation model, using Spectral Analyzer measurements. The
signal is generated by two Access Points (APs) on the base floor at
the administrative Communication School of ESPOL building. In
general, users do not have a Q&S reference about a wireless network;
however, this depends on the level signal as a function of frequency,
distance and other path conditions between receiver and transmitter.
Then, power density of the signal decrease as it propagates through
space and data transfer rate is affected. This document evaluates and
implements empirical mathematical formulation for the
characterization of WLAN radio wave propagation on two aisles of
the building base floor.
Abstract: The main objective of this study was to demonstrate that differentiation of infected and vaccinated animals (DIVA) strategy using different ELISA tests is possible when a subunit vaccine (Haemagglutinin protein) is used to prevent Avian influenza. Special emphasis was placed on the differentiation in the serological response to different components of the AIV (Nucleoprotein, Neuraminidase, Haemagglutinin, Nucleocapsid) between chickens that were vaccinated with a whole virus kill vaccine and recombinant vaccine. Furthermore, the potential use of this DIVA strategy using ELISA assays to detect Neuraminidase 1 (N1) was analyzed as strategy in countries where the field virus is H5N1 and the vaccine used is formulated with H5N2. Detection of AIV-s antibodies to any component in serum was negative for all animals on the study days 0-13. At study day 14 the titers of antibodies against Nucleoprotein (NP) and Nucleocapsid (NC) rose in the experimental groups vaccinated with Volvac® AI KV and were negatives during all the trial in the experimental groups vaccinated with a subunit H5; significant statistically differences were observed between these groups (p < 0.05). The seroconversion either Haemagglutinin or Neuraminidase was evident after 21 days post-vaccination in the experimental groups vaccinated with the respective viral fraction. Regarding the main aim of this study and according with the results that were obtained, use a combination of different ELISA test as a DIVA strategy is feasible when the vaccination is carry out with a subunit H5 vaccine. Also is possible to use the ELISA kit to detect Neuraminidase (either N1 or N2) as a DIVA concept in countries where H5N1 is present and the vaccination programs are done with H5N2 vaccine.
Abstract: This work is focused on the numerical prediction of the fracture resistance of a flat stiffened panel made of the aluminium alloy 2024 T3 under a monotonic traction condition. The performed numerical simulations have been based on the micromechanical Gurson-Tvergaard (GT) model for ductile damage. The applicability of the GT model to this kind of structural problems has been studied and assessed by comparing numerical results, obtained by using the WARP 3D finite element code, with experimental data available in literature. In the sequel a home-made procedure is presented, which aims to increase the residual strength of a cracked stiffened aluminum panel and which is based on the stochastic design improvement (SDI) technique; a whole application example is then given to illustrate the said technique.