Abstract: This paper proposes an active soft-switching circuit for
bridge converters aiming to improve the power conversion efficiency.
The proposed circuit achieves loss-less switching for both main and
auxiliary switches without increasing the main switch current/voltage
rating. A winding coupled to the primary of power transformer
ensures ZCS for the auxiliary switches during their turn-off. A 350 W,
100 kHz phase shifted full bridge (PSFB) converter is built to validate
the analysis and design. Theoretical loss calculations for proposed
circuit is presented. The proposed circuit is compared with passive
soft switched PSFB in terms of efficiency and loss in duty cycle.
Abstract: This paper presents a novel approach for optimal
reconfiguration of radial distribution systems. Optimal
reconfiguration involves the selection of the best set of branches to
be opened, one each from each loop, such that the resulting radial
distribution system gets the desired performance. In this paper an
algorithm is proposed based on simple heuristic rules and identified
an effective switch status configuration of distribution system for the
minimum loss reduction. This proposed algorithm consists of two
parts; one is to determine the best switching combinations in all loops
with minimum computational effort and the other is simple optimum
power loss calculation of the best switching combination found in
part one by load flows. To demonstrate the validity of the proposed
algorithm, computer simulations are carried out on 33-bus system.
The results show that the performance of the proposed method is
better than that of the other methods.
Abstract: This research study the application of the immobilized
TiO2 layer and Cu-TiO2 layer on graphite substrate as a negative
electrode or anode for Li-ion battery. The titania layer was produced
through chemical bath deposition method, meanwhile Cu particles
were deposited electrochemically. A material can be used as an
electrode as it has capability to intercalates Li ions into its crystal
structure. The Li intercalation into TiO2/Graphite and Cu-
TiO2/Graphite were analyzed from the changes of its XRD pattern
after it was used as electrode during discharging process. The XRD
patterns were refined by Le Bail method in order to determine the
crystal structure of the prepared materials. A specific capacity and the
cycle ability measurement were carried out to study the performance
of the prepared materials as negative electrode of the Li-ion battery.
The specific capacity was measured during discharging process from
fully charged until the cut off voltage. A 300 was used as a load.
The result shows that the specific capacity of Li-ion battery with
TiO2/Graphite as negative electrode is 230.87 ± 1.70mAh.g-1 which is
higher than the specific capacity of Li-ion battery with pure graphite
as negative electrode, i.e 140.75 ±0.46mAh.g-1. Meanwhile
deposition of Cu onto TiO2 layer does not increase the specific
capacity, and the value even lower than the battery with
TiO2/Graphite as electrode. The cycle ability of the prepared battery
is only two cycles, due to the Li ribbon which was used as cathode
became fragile and easily broken.
Abstract: The complexity of lignocellulosic biomass requires
a pretreatment step to improve the yield of fermentable sugars. The
efficient pretreatment of corn cobs using microwave and potassium
hydroxide and enzymatic hydrolysis was investigated. The
objective of this work was to characterize the optimal condition of
pretreatment of corn cobs using microwave and potassium
hydroxide enhance enzymatic hydrolysis. Corn cobs were
submerged in different potassium hydroxide concentration at varies
temperature and resident time. The pretreated corn cobs were
hydrolyzed to produce the reducing sugar for analysis. The
morphology and microstructure of samples were investigated by
Thermal gravimetric analysis (TGA, scanning electron microscope
(SEM), X-ray diffraction (XRD). The results showed that lignin
and hemicellulose were removed by microwave/potassium
hydroxide pretreatment. The crystallinity of the pretreated corn
cobs was higher than the untreated. This method was compared
with autoclave and conventional heating method. The results
indicated that microwave-alkali treatment was an efficient way to
improve the enzymatic hydrolysis rate by increasing its
accessibility hydrolysis enzymes.
Abstract: In theoretical computer science, the Turing machine has played a number of important roles in understanding and exploiting basic concepts and mechanisms in computing and information processing [20]. It is a simple mathematical model of computers [9]. After that, M.Blum and C.Hewitt first proposed two-dimensional automata as a computational model of two-dimensional pattern processing, and investigated their pattern recognition abilities in 1967 [7]. Since then, a lot of researchers in this field have been investigating many properties about automata on a two- or three-dimensional tape. On the other hand, the question of whether processing fourdimensional digital patterns is much more difficult than two- or threedimensional ones is of great interest from the theoretical and practical standpoints. Thus, the study of four-dimensional automata as a computasional model of four-dimensional pattern processing has been meaningful [8]-[19],[21]. This paper introduces a cooperating system of four-dimensional finite automata as one model of four-dimensional automata. A cooperating system of four-dimensional finite automata consists of a finite number of four-dimensional finite automata and a four-dimensional input tape where these finite automata work independently (in parallel). Those finite automata whose input heads scan the same cell of the input tape can communicate with each other, that is, every finite automaton is allowed to know the internal states of other finite automata on the same cell it is scanning at the moment. In this paper, we mainly investigate some accepting powers of a cooperating system of eight- or seven-way four-dimensional finite automata. The seven-way four-dimensional finite automaton is an eight-way four-dimensional finite automaton whose input head can move east, west, south, north, up, down, or in the fu-ture, but not in the past on a four-dimensional input tape.
Abstract: The IDR(s) method based on an extended IDR theorem was proposed by Sonneveld and van Gijzen. The original IDR(s) method has excellent property compared with the conventional iterative methods in terms of efficiency and small amount of memory. IDR(s) method, however, has unexpected property that relative residual 2-norm stagnates at the level of less than 10-12. In this paper, an effective strategy for stagnation detection, stagnation avoidance using adaptively information of parameter s and improvement of convergence rate itself of IDR(s) method are proposed in order to gain high accuracy of the approximated solution of IDR(s) method. Through numerical experiments, effectiveness of adaptive tuning IDR(s) method is verified and demonstrated.
Abstract: Most of the existing text mining approaches are
proposed, keeping in mind, transaction databases model. Thus, the
mined dataset is structured using just one concept: the “transaction",
whereas the whole dataset is modeled using the “set" abstract type. In
such cases, the structure of the whole dataset and the relationships
among the transactions themselves are not modeled and
consequently, not considered in the mining process.
We believe that taking into account structure properties of
hierarchically structured information (e.g. textual document, etc ...)
in the mining process, can leads to best results. For this purpose, an
hierarchical associations rule mining approach for textual documents
is proposed in this paper and the classical set-oriented mining
approach is reconsidered profits to a Direct Acyclic Graph (DAG)
oriented approach. Natural languages processing techniques are used
in order to obtain the DAG structure. Based on this graph model, an
hierarchical bottom up algorithm is proposed. The main idea is that
each node is mined with its parent node.
Abstract: The research investigates the effects of super plasticizer and molarity of sodium hydroxide alkaline solution on the workability, microstructure and compressive strength of self compacting geopolymer concrete (SCGC). SCGC is an improved way of concreting execution that does not require compaction and is made by complete elimination of ordinary Portland cement content. The parameters studied were superplasticizer (SP) dosage and molarity of NaOH solution. SCGC were synthesized from low calcium fly ash, activated by combinations of sodium hydroxide and sodium silicate solutions, and by incorporation of superplasticizer for self compactability. The workability properties such as filling ability, passing ability and resistance to segregation were assessed using slump flow, T-50, V-funnel, L-Box and J-ring test methods. It was found that the essential workability requirements for self compactability according to EFNARC were satisfied. Results showed that the workability and compressive strength improved with the increase in superplasticizer dosage. An increase in strength and a decrease in workability of these concrete samples were observed with the increase in molarity of NaOH solution from 8M to 14M. Improvement of interfacial transition zone (ITZ) and micro structure with the increase of SP and increase of concentration from 8M to 12M were also identified.
Abstract: Mercury is a natural occurring element and present in
various concentrations in the environment. Due to its toxic effects, it
is desirable to research mercury sensitive materials to adsorb
mercury. This paper describes the preparation of Au nanoparticles for
mercury adsorption by using a microwave (MW)-polyol method in
the presence of three different Sodium Chloride (NaCl)
concentrations (10, 20 and 30 mM). Mixtures of spherical, triangular,
octahedral, decahedral particles and 1-D product were obtained using
this rapid method. Sizes and shapes was found strongly depend on the
concentrations of NaCl. Without NaCl concentration, spherical,
triangular plates, octahedral, decahedral nanoparticles and 1D
product were produced. At the lower NaCl concentration (10 mM),
spherical, octahedral and decahedral nanoparticles were present,
while spherical and decahedral nanoparticles were preferentially form
by using 20 mM of NaCl concentration. Spherical, triangular plates,
octahedral and decahedral nanoparticles were obtained at the highest
NaCl concentration (30 mM). The amount of mercury adsorbed using
20 ppm mercury solution is the highest (67.5 %) for NaCl
concentration of 30 mM. The high yield of polygonal particles will
increase the mercury adsorption. In addition, the adsorption of
mercury is also due to the sizes of the particles. The sizes of particles
become smaller with increasing NaCl concentrations (size ranges, 5-
16 nm) than those synthesized without addition of NaCl (size ranges
11-32 nm). It is concluded that NaCl concentrations affects the
formation of sizes and shapes of Au nanoparticles thus affects the
mercury adsorption.
Abstract: In this paper, an inventory model with finite and
constant replenishment rate, price dependant demand rate, time
value of money and inflation, finite time horizon, lead time and
exponential deterioration rate and with the objective of maximizing
the present worth of the total system profit is developed. Using a
dynamic programming based solution algorithm, the optimal
sequence of the cycles can be found and also different optimal
selling prices, optimal order quantities and optimal maximum
inventories can be obtained for the cycles with unequal lengths,
which have never been done before for this model. Also, a
numerical example is used to show accuracy of the solution
procedure.
Abstract: Many companies have switched their processes to project-oriented in the last years. This brings new possibilities and effectiveness not only in the field of external processes connected with the product delivery but also the internal processes as well. However centralized project organization which is based on the role of project manager in the team has proved insufficient in some cases. Agile methods of project organization are trying to solve this problem by bringing new view on the project organization, roles, processes and competences. Scrum is one of these methods which builds on the principles of knowledge management to drive the project to effectiveness from all view angles. Using this method to organize internal and delivery projects helps the organization to create and share knowledge throughout the company. It also supports forming unique competences of individuals and project teams and drives innovations in the company.
Abstract: School homework has been synonymous with students- life in Chinese national type primary schools in Malaysia. Although many reports in the press claimed that students were burdened with too much of it, homework continues to be a common practice in national type schools that is believed to contribute to academic achievement. This study is conducted to identify the relationship between the burden of school homework and academic achievement among pupils in Chinese National Type Primary School in the state of Perak, Malaysia. A total of 284 students (142 from urban and 142 from rural) respectively were chosen as participants in this study. Variables of gender and location (urban/rural areas) has shown significant difference in student academic achievement. Female Chinese student from rural areas showed a higher mean score than males from urban area. Therefore, the Chinese language teachers should give appropriate and relevant homework to primary school students to achieve good academic performance.
Abstract: This paper deals with a delayed single population model on time scales. With the assistance of coincidence degree theory, sufficient conditions for existence of periodic solutions are obtained. Furthermore, the better estimations for bounds of periodic solutions are established.
Abstract: Our Medicine-oriented research is based on a medical
data set of real patients. It is a security problem to share
patient private data with peoples other than clinician or hospital
staff. We have to remove person identification information
from medical data. The medical data without private data
are available after a de-identification process for any research
purposes. In this paper, we introduce an universal automatic
rule-based de-identification application to do all this stuff on an
heterogeneous medical data. A patient private identification is
replaced by an unique identification number, even in burnedin
annotation in pixel data. The identical identification is used
for all patient medical data, so it keeps relationships in a data.
Hospital can take an advantage of a research feedback based
on results.
Abstract: Shrunken patterning for integrated device
manufacturing requires surface cleanliness and surface smoothness in
wet chemical processing [1]. It is necessary to control all process
parameters perfectly especially for the common cleaning technique
RCA clean (SC-1 and SC-2) [2]. In this paper the characteristic and
effect of surface preparation parameters are discussed. The properties
of RCA wet chemical processing in silicon technology is based on
processing time, temperature, concentration and megasonic power of
SC-1 and QDR. An improvement of wafer surface preparation by
the enhanced variables of the wet cleaning chemical process is
proposed.
Abstract: This paper presents the use of Legendre pseudospectral
method for the optimization of finite-thrust orbital transfer for
spacecrafts. In order to get an accurate solution, the System-s
dynamics equations were normalized through a dimensionless method.
The Legendre pseudospectral method is based on interpolating
functions on Legendre-Gauss-Lobatto (LGL) quadrature nodes. This
is used to transform the optimal control problem into a constrained
parameter optimization problem. The developed novel optimization
algorithm can be used to solve similar optimization problems of
spacecraft finite-thrust orbital transfer. The results of a numerical
simulation verified the validity of the proposed optimization method.
The simulation results reveal that pseudospectral optimization method
is a promising method for real-time trajectory optimization and
provides good accuracy and fast convergence.
Abstract: In this paper, we propose a robust face relighting
technique by using spherical space properties. The proposed method
is done for reducing the illumination effects on face recognition.
Given a single 2D face image, we relight the face object by
extracting the nine spherical harmonic bases and the face spherical
illumination coefficients. First, an internal training illumination
database is generated by computing face albedo and face normal
from 2D images under different lighting conditions. Based on the
generated database, we analyze the target face pixels and compare
them with the training bootstrap by using pre-generated tiles. In this
work, practical real time processing speed and small image size were
considered when designing the framework. In contrast to other works,
our technique requires no 3D face models for the training process
and takes a single 2D image as an input. Experimental results on
publicly available databases show that the proposed technique works
well under severe lighting conditions with significant improvements
on the face recognition rates.
Abstract: We analyze the effectivity of different pseudo noise (PN) and orthogonal sequences for encrypting speech signals in terms of perceptual intelligence. Speech signal can be viewed as sequence of correlated samples and each sample as sequence of bits. The residual intelligibility of the speech signal can be reduced by removing the correlation among the speech samples. PN sequences have random like properties that help in reducing the correlation among speech samples. The mean square aperiodic auto-correlation (MSAAC) and the mean square aperiodic cross-correlation (MSACC) measures are used to test the randomness of the PN sequences. Results of the investigation show the effectivity of large Kasami sequences for this purpose among many PN sequences.
Abstract: A steady two-phase flow model has been developed to simulate the drying process of porous particle in a pneumatic conveying dryer. The model takes into account the momentum, heat and mass transfer between the continuous phase and the dispersed phase. A single particle model was employed to calculate the evaporation rate. In this model the pore structure is simplified to allow the dominant evaporation mechanism to be readily identified at all points within the duct. The predominant mechanism at any time depends upon the pressure, temperature and the diameter of pore from which evaporating is occurring. The model was validated against experimental studies of pneumatic transport at low and high speeds as well as pneumatic drying. The effects of operating conditions on the dryer parameters are studied numerically. The present results show that the drying rate is enhanced as the inlet gas temperature and the gas flow rate increase and as the solid mass flow rate deceases. The present results also demonstrate the necessity of measuring the inlet gas velocity or the solid concentration in any experimental analysis.
Abstract: Continuously growing needs for Internet applications
that transmit massive amount of data have led to the emergence of
high speed network. Data transfer must take place without any
congestion and hence feedback parameters must be transferred from
the receiver end to the sender end so as to restrict the sending rate in
order to avoid congestion. Even though TCP tries to avoid
congestion by restricting the sending rate and window size, it never
announces the sender about the capacity of the data to be sent and
also it reduces the window size by half at the time of congestion
therefore resulting in the decrease of throughput, low utilization of
the bandwidth and maximum delay. In this paper, XCP protocol is
used and feedback parameters are calculated based on arrival rate,
service rate, traffic rate and queue size and hence the receiver
informs the sender about the throughput, capacity of the data to be
sent and window size adjustment, resulting in no drastic decrease in
window size, better increase in sending rate because of which there is
a continuous flow of data without congestion. Therefore as a result of
this, there is a maximum increase in throughput, high utilization of
the bandwidth and minimum delay. The result of the proposed work
is presented as a graph based on throughput, delay and window size.
Thus in this paper, XCP protocol is well illustrated and the various
parameters are thoroughly analyzed and adequately presented.