Abstract: Phase equilibria of AZ91D Mg alloys for
nonflammable use, containing Ca and Y, were carried out by using
FactSage® and FTLite database, which revealed that solid solution
treatment could be performed at temperatures from 400 to 450oC.
Solid solution treatment of AZ91D Mg alloy without Ca and Y was
successfully conducted at 420oC and supersaturated microstructure
with all beta phase resolved into matrix was obtained. In the case of
AZ91D Mg alloy with some Ca and Y; however, a little amount of
intermetallic particles were observed after solid solution treatment.
After solid solution treatment, each alloy was annealed at temperatures
of 180 and 200oC for time intervals from 1 min to 48 hrs and hardness
of each condition was measured by micro-Vickers method. Peak aging
conditions were deduced as at the temperature of 200oC for 10 hrs.
Abstract: In many communication and signal processing
systems, it is highly desirable to implement an efficient narrow-band
filter that decimate or interpolate the incoming signals. This paper
presents hardware efficient compensated CIC filter over a narrow
band frequency that increases the speed of down sampling by using
multiplierless decimation filters with polyphase FIR filter structure.
The proposed work analyzed the performance of compensated CIC
filter on the bases of the improvement of frequency response with
reduced hardware complexity in terms of no. of adders and
multipliers and produces the filtered results without any alterations.
CIC compensator filter demonstrated that by using compensation
with CIC filter improve the frequency response in passed of interest
26.57% with the reduction in hardware complexity 12.25%
multiplications per input sample (MPIS) and 23.4% additions per
input sample (APIS) w.r.t. FIR filter respectively.
Abstract: The ever increasing amount of solid waste (SW)
generated which is exacerbated by lack of proper waste management
system is of growing concern worldwide and in major cities in
developing countries due to its social, economic and environmental
implications. This study attempts to describe the aspects of solid
waste management (SWM) in Adama, one of the fast urbanizing
cities in Ethiopia, and highlights the challenges thereof. Data were
gathered through interview supplemented by field observation and
self-administered questionnaire. Then, the data were analyzed using
the Statistical Package for Social Science (SPSS) software. In
addition, secondary data were gathered from documents. Findings
revealed that the current SWM practice couldn’t cope with the fast
urbanizing needs and the rapid population growth exhibited by the
city. Besides, major factors contributing to the inefficient system
were identified. The study would provide practical insights to
decision makers in developing a sustainable SWM system leading to
minimized risk in the city.
Abstract: Heating, cooling and lighting appliances in buildings
account for more than one third of the world’s primary energy
demand. Therefore, main components of the building heating systems
play an essential role in terms of energy consumption. In this context,
efficient energy and exergy utilization in HVAC-R systems has been
very essential, especially in developing energy policies towards
increasing efficiencies. The main objective of the present study is to
assess the performance of a family house with a volume of 326.7 m3
and a net floor area of 121 m2, located in the city of Izmir, Turkey in
terms of energetic, exergetic and sustainability aspects. The indoor
and exterior air temperatures are taken as 20°C and 1°C, respectively.
In the analysis and assessment, various metrics (indices or indicators)
such as exergetic efficiency, exergy flexibility ratio and sustainability
index are utilized. Two heating options (Case 1: condensing boiler
and Case 2: air heat pump) are considered for comparison purposes.
The total heat loss rate of the family house is determined to be
3770.72 W. The overall energy efficiencies of the studied cases are
calculated to be 49.4% for Case 1 and 54.7% for Case 2. The overall
exergy efficiencies, the flexibility factor and the sustainability index
of Cases 1 and 2 are computed to be around 3.3%, 0.17 and 1.034,
respectively.
Abstract: This study models the use of transcutaneous electrical
nerve stimulation on skin with a disk electrode in order to simulate
tissue damage. The current density distribution above a disk electrode
is known to be a dynamic and non-uniform quantity that is intensified
at the edges of the disk. The non-uniformity is subject to change
through using various electrode geometries or stimulation methods.
One of these methods known as edge-retarded stimulation has shown
to reduce this edge enhancement. Though progress has been made in
modeling the behavior of a disk electrode, little has been done to test
the validity of these models in simulating the actual heat transfer
from the electrode. This simulation uses finite element software to
couple the injection of current from a disk electrode to heat transfer
described by the Pennesbioheat transfer equation. An example
application of this model is studying an experimental form of
stimulation, known as edge-retarded stimulation. The edge-retarded
stimulation method will reduce the current density at the edges of the
electrode. It is hypothesized that reducing the current density edge
enhancement effect will, in turn, reduce temperature change and
tissue damage at the edges of these electrodes. This study tests this
hypothesis as a demonstration of the capabilities of this model. The
edge-retarded stimulation proved to be safer after this simulation. It is
shown that temperature change and the fraction of tissue necrosis is
much greater in the square wave stimulation. These results bring
implications for changes of procedures in transcutaneous electrical
nerve stimulation and transcutaneous spinal cord stimulation as well.
Abstract: Azadirachta excelsa or locally known as sentang are
frequently used as a traditional medicine by diabetes patients in
Malaysia. However, less attention has been given to their toxicity
effect. Thus, the study is an attempt to examine the protective effect
of A. excelsa on the pancreas and to determine possible toxicity
mediated by the extract. Diabetes was induced experimentally in rats
by high-fat-diet for 16 weeks followed by intraperitoneal injection of
streptozotocin at dosage of 35 mg/kg of body weight. Declination of
the fasting blood glucose level was observed after continuous
administration of A. excelsa for 14 days twice daily. This is due to the
refining structure of the pancreas. However, surprisingly, the plant
extract reduced the leukocytes, erythrocytes, hemoglobin, MCHC and
lymphocytes. In addition, the rat treated with the plant extract
exhibited increment in AST and eosinocytes level. Overall, the
finding shows that A. excelsa possesses antidiabetic activity by
improving the structure of pancreatic islet of Langerhans but
involved in ameliorating of hematology and biochemical parameters.
Abstract: In this study, six bacterial isolates of a slightly
thermophilic organism from the Sg. Klah hot spring, Malaysia were
successfully isolated and designated as M7T55D1, M7T55D2,
M7T55D3, M7T53D1, M7T53D2 and M7T53D3 respectively. The
bacterial isolates were screened for their cellulose hydrolytic ability
on Carboxymethlycellulose agar medium. The isolated bacterial
strains were identified morphologically, biochemically and
molecularly with the aid of 16S rDNA sequencing. All of the bacteria
showed their optimum growth at a slightly alkaline pH of 7.5 with a
temperature of 55°C. All strains were Gram-negative, non-spore
forming type, strictly aerobic, catalase-positive and oxidase-positive
with the ability to produce thermostable cellulase. Based on BLASTn
results, bacterial isolates of M7T55D2 and M7T53D1 gave the
highest homology (97%) with similarity to Tepidimonas ignava while
isolates M7T55D1, M7T55D3, M7T53D2 and M7T53D3 showed
their closest homology (97%-98%) with Tepidimonas thermarum.
These cellulolytic thermophiles might have a commercial potential to
produce valuable thermostable cellulase.
Abstract: This paper presents the variation of the dynamic
characteristics of a spindle with the change of bearing preload. The
correlations between the variation of bearing preload and fundamental
modal parameters were first examined by conducting vibration tests on
physical spindle units. Experimental measurements show that the
dynamic compliance and damping ratio associated with the
dominating modes were affected to vary with variation of the bearing
preload. When the bearing preload was slightly deviated from a
standard value, the modal frequency and damping ability also vary to
different extent, which further enable the spindle to perform with
different compliance. For the spindle used in this study, a standard
preload value set on bearings would enable the spindle to behave a
higher stiffness as compared with others with a preload variation. This
characteristic can be served as a reference to examine the variation of
bearing preload of spindle in assemblage or operation.
Abstract: We used high-precision Global Positioning System
(GPS) to geodetically constrain the motion of stations in the
Darjiling-Sikkim Himalayan (DSH) wedge and examine the
deformation at the Indian-Tibetan plate boundary using IGS
(International GPS Service) fiducial stations. High-precision GPS
based displacement and velocity field was measured in the DSH
between 1997 and 2009. To obtain additional insight north of the
Indo-Tibetan border and in the Darjiling-Sikkim-Tibet (DaSiT)
wedge, published velocities from four stations J037, XIGA, J029 and
YADO were also included in the analysis. India-fixed velocities or
the back-slip was computed relative to the pole of rotation of the
Indian Plate (Latitude 52.97 ± 0.22º, Longitude - 0.30 ± 3.76º, and
Angular Velocity 0.500 ± 0.008º/ Myr) in the DaSiT wedge.
Dislocation modelling was carried out with the back-slip to model the
best possible solution of a finite rectangular dislocation or the
causative fault based on dislocation theory that produced the
observed back-slip using a forward modelling approach. To find the
best possible solution, three different models were attempted. First,
slip along a single thrust fault, then two thrust faults and in finally,
three thrust faults were modelled to simulate the back-slip in the
DaSiT wedge. The three-fault case bests the measured displacements
and is taken as the best possible solution.
Abstract: In order to evaluate the performance of a unified power
flow controller (UPFC), mathematical models for steady state and
dynamic analysis are to be developed. The steady state model is
mainly concerned with the incorporation of the UPFC in load flow
studies. Several load flow models for UPFC have been introduced
in literature, and one of the most reliable models is the decoupled
UPFC model. In spite of UPFC decoupled load flow model simplicity,
it is more robust compared to other UPFC load flow models and it
contains unique capabilities. Some shortcoming such as additional
set of nonlinear equations are to be solved separately after the load
flow solution is obtained. The aim of this study is to investigate the
different control strategies that can be realized in the decoupled load
flow model (individual control and combined control), and the impact
of the location of the UPFC in the network on its control parameters.
Abstract: Analysis of real life problems often results in linear
systems of equations for which solutions are sought. The method to
employ depends, to some extent, on the properties of the coefficient
matrix. It is not always feasible to solve linear systems of equations
by direct methods, as such the need to use an iterative method
becomes imperative. Before an iterative method can be employed
to solve a linear system of equations there must be a guaranty that
the process of solution will converge. This guaranty, which must
be determined apriori, involve the use of some criterion expressible
in terms of the entries of the coefficient matrix. It is, therefore,
logical that the convergence criterion should depend implicitly on the
algebraic structure of such a method. However, in deference to this
view is the practice of conducting convergence analysis for Gauss-
Seidel iteration on a criterion formulated based on the algebraic
structure of Jacobi iteration. To remedy this anomaly, the Gauss-
Seidel iteration was studied for its algebraic structure and contrary
to the usual assumption, it was discovered that some property of the
iteration matrix of Gauss-Seidel method is only diagonally dominant
in its first row while the other rows do not satisfy diagonal dominance.
With the aid of this structure we herein fashion out an improved
version of Gauss-Seidel iteration with the prospect of enhancing
convergence and robustness of the method. A numerical section is
included to demonstrate the validity of the theoretical results obtained
for the improved Gauss-Seidel method.
Abstract: The high Peak to Average Power Ratio (PAR) in Filter
Bank Multicarrier with Offset Quadrature Amplitude Modulation
(FBMC-OQAM) can significantly reduce power efficiency and
performance. In this paper, we address the problem of PAPR
reduction for FBMC-OQAM systems using Tone Reservation (TR)
technique. Due to the overlapping structure of FBMCOQAM signals,
directly applying TR schemes of OFDM systems to FBMC-OQAM
systems is not effective. We improve the tone reservation (TR)
technique by employing sliding window with Active Constellation
Extension for the PAPR reduction of FBMC-OQAM signals, called
sliding window tone reservation Active Constellation Extension
(SW-TRACE) technique. The proposed SW-TRACE technique uses
the peak reduction tones (PRTs) of several consecutive data
blocks to cancel the peaks of the FBMC-OQAM signal inside a
window, with dynamically extending outer constellation points in
active(data-carrying) channels, within margin-preserving constraints,
in order to minimize the peak magnitude. Analysis and simulation
results compared to the existing Tone Reservation (TR) technique for
FBMC/OQAM system. The proposed method SW-TRACE has better
PAPR performance and lower computational complexity.
Abstract: This work presents the modelling and simulation of
saponification of ethyl acetate in the presence of sodium hydroxide in
a plug flow reactor using Aspen Plus simulation software. Plug flow
reactors are widely used in the industry due to the non-mixing
property. The use of plug flow reactors becomes significant when
there is a need for continuous large scale reaction or fast reaction.
Plug flow reactors have a high volumetric unit conversion as the
occurrence for side reactions is minimum. In this research Aspen Plus
V8.0 has been successfully used to simulate the plug flow reactor. In
order to simulate the process as accurately as possible HYSYS Peng-
Robinson EOS package was used as the property method. The results
obtained from the simulation were verified by the experiment carried
out in the EDIBON plug flow reactor module. The correlation
coefficient (r2) was 0.98 and it proved that simulation results
satisfactorily fit for the experimental model. The developed model
can be used as a guide for understanding the reaction kinetics of a
plug flow reactor.
Abstract: Lead (Pb) poisoning is one of the most common and
preventable environmental health problems. There are different
sources of environmental pollution with lead as lead alkyl additives
in petrol and manufacturing processes. Pb in the atmosphere can be
deposited in urban soils, and may then be re-suspended to re-enter the
atmosphere. This could increase human exposure to Pb and cause
long-term health effects. Thus, monitoring Pb pollution is considered
one of the major tasks in controlling pollution. Scalp hair can be
utilized for the determination of lead (Pb) concentration. It provides a
lasting record of metal intakes of weeks or even months, and for most
metals, their accumulation in hair reflects their accumulation in the
whole body. This work was conducted to investigate the
concentration of lead in male scalp hair of Cairo (residential-traffic
and residential-industrial) and rural residents after twenty years of
phasing out of leaded gasoline. Results indicated that the mean
concentration of lead in hair of residential-traffic (9.7552 μg/g ±0.71)
and residential-industrial (12.3288 μg/g ±1.13) was significantly
higher than that in rural residents (4.7327 μg/g ±0.67). The mean
concentration of lead in hair of resident’s industrial areas was the
highest among Cairo residents and not the traffic areas as it was
before phasing out of leaded gasoline. Twenty years of phasing out of
leaded gasoline in Cairo has greatly improved the lead pollution
among residents of traffic areas, but industrial areas residents were
still suffering from lead pollution, which needs more efforts to
control the sources of lead pollution.
Abstract: Biological conversion of biomass to methane has
received increasing attention in recent years. Grasses have been
explored for their potential anaerobic digestion to methane. In this
review, extensive literature data have been tabulated and classified.
The influences of several parameters on the potential of these
feedstocks to produce methane are presented. Lignocellulosic
biomass represents a mostly unused source for biogas and ethanol
production. Many factors, including lignin content, crystallinity of
cellulose, and particle size, limit the digestibility of the hemicellulose
and cellulose present in the lignocellulosic biomass. Pretreatments
have used to improve the digestibility of the lignocellulosic biomass.
Each pretreatment has its own effects on cellulose, hemicellulose and
lignin, the three main components of lignocellulosic biomass. Solidstate
anaerobic digestion (SS-AD) generally occurs at solid
concentrations higher than 15%. In contrast, liquid anaerobic
digestion (AD) handles feedstocks with solid concentrations between
0.5% and 15%. Animal manure, sewage sludge, and food waste are
generally treated by liquid AD, while organic fractions of municipal
solid waste (OFMSW) and lignocellulosic biomass such as crop
residues and energy crops can be processed through SS-AD. An
increase in operating temperature can improve both the biogas yield
and the production efficiency, other practices such as using AD
digestate or leachate as an inoculant or decreasing the solid content
may increase biogas yield but have negative impact on production
efficiency. Focus is placed on substrate pretreatment in anaerobic
digestion (AD) as a means of increasing biogas yields using today’s
diversified substrate sources.
Abstract: Application of hulls processing technologies, based on high-concentrated energy sources (laser and plasma technologies), allow improve shipbuilding production. It is typical for high-speed vessels construction using steel and aluminum alloys with high precision hulls required. Report describes high-performance technologies for plasma welding (using direct current of reversed polarity), laser, and hybrid laser-arc welding of hulls structures developed by JSC “SSTC”
Abstract: It is known that residual welding deformations give
negative effect to processability and operational quality of welded
structures, complicating their assembly and reducing strength.
Therefore, selection of optimal technology, ensuring minimum
welding deformations, is one of the main goals in developing a
technology for manufacturing of welded structures.
Through years, JSC SSTC has been developing a theory for
estimation of welding deformations and practical activities for
reducing and compensating such deformations during welding
process. During long time a methodology was used, based on analytic
dependence. This methodology allowed defining volumetric changes
of metal due to welding heating and subsequent cooling. However,
dependences for definition of structures deformations, arising as a
result of volumetric changes of metal in the weld area, allowed
performing calculations only for simple structures, such as units, flat
sections and sections with small curvature. In case of complex 3D
structures, estimations on the base of analytic dependences gave
significant errors.
To eliminate this shortage, it was suggested to use finite elements
method for resolving of deformation problem. Here, one shall first
calculate volumes of longitudinal and transversal shortenings of
welding joints using method of analytic dependences and further,
with obtained shortenings, calculate forces, which action is
equivalent to the action of active welding stresses. Further, a finiteelements
model of the structure is developed and equivalent forces
are added to this model. Having results of calculations, an optimal
sequence of assembly and welding is selected and special measures to
reduce and compensate welding deformations are developed and
taken.
Abstract: The emergence of the Semantic Web technology
increases day by day due to the rapid growth of multiple web pages.
Many standard formats are available to store the semantic web data.
The most popular format is the Resource Description Framework
(RDF). Querying large RDF graphs becomes a tedious procedure
with a vast increase in the amount of data. The problem of query
optimization becomes an issue in querying large RDF graphs.
Choosing the best query plan reduces the amount of query execution
time. To address this problem, nature inspired algorithms can be used
as an alternative to the traditional query optimization techniques. In
this research, the optimal query plan is generated by the proposed
SAPSO algorithm which is a hybrid of Simulated Annealing (SA)
and Particle Swarm Optimization (PSO) algorithms. The proposed
SAPSO algorithm has the ability to find the local optimistic result
and it avoids the problem of local minimum. Experiments were
performed on different datasets by changing the number of predicates
and the amount of data. The proposed algorithm gives improved
results compared to existing algorithms in terms of query execution
time.
Abstract: High temperature deformation behavior of cast
Fe-20Cr-5Al alloy has been investigated in this study by performing
tensile and compression tests at temperatures from 1100 to 1200oC.
Rectangular ingots of which the dimensions were 300×300×100 in
millimeter were cast using vacuum induction melting. Phase
equilibrium was calculated using the FactSage®, thermodynamic
software and database. Tensile strength of cast Fe-20Cr-5Al alloy was
4 MPa at 1200oC. With temperature decreased, tensile strength
increased rapidly and reached up to 13 MPa at 1100oC. Elongation
also increased from 18 to 80% with temperature decreased from
1200oC to 1100oC. Microstructure observation revealed that M23C6
carbide was precipitated along the grain boundary and within the
matrix.
Abstract: Enzyme activity was evaluated in the intestine of
juvenile dourado (Salminus brasiliensis) fed with diets containing 0,
10 or 20% of lyophilized bovine colostrum (LBC) inclusion for either
30 or 60 days. The intestinal enzymes acid and alkaline phosphatase
(ACP and ALP, respectively), non-specific esterase (NSE), lipase
(LIP), dipeptidyl aminopeptidase IV (DAP IV) and leucine
aminopeptidase (LAP) were studied using histochemistry in four
intestinal segments (S1, S2, S3 and posterior intestine). Weak
proteolitic activity was observed in all intestinal segments for DAP
IV and LAP. The activity of NSE and LIP was also weak in all
intestines, except for the moderate activity of NSE in the S2 of 20%
LBC group after 30 days and in the S1 of 0% LBC group after 60
days. The ACP was detected only in the S2 and S3 of the 10% LBC
group after 30 days. Moderate and strong staining was observed in
the first three intestinal segments for ALP and weak activity in the
posterior intestine. The activity of DAP IV, LAP and ALP were also
present in the cytoplasm of the enterocytes. In the present results,
bovine colostrum feeding did not cause alterations in activity of
intestinal enzymes.