Abstract: With respect to the dissipation of energy through
plastic deformation of joints of prefabricated wall units, the paper
points out the principal importance of efficient reinforcement of the
prefabricated system at its joints. The method, quality and amount of
reinforcement are essential for reaching the necessary degree of joint
ductility. The paper presents partial results of experimental research
of vertical joints of prefabricated units exposed to monotonously
rising loading and repetitive shear force and formulates a conclusion
that the limit state of the structure as a whole is preceded by the
disintegration of joints, or that the structure tends to pass from
linearly elastic behaviour to non-linearly elastic to plastic behaviour
by exceeding the proportional elastic limit in joints.Experimental
verification on a model of a 7-storey prefabricated structure revealed
weak points in its load-bearing systems, mainly at places of critical
points around openings situated in close proximity to vertical joints
of mutually perpendicularly oriented walls.
Abstract: The aim of this paper is to propose a mathematical
model to determine invariant sets, set covering, orbits and, in
particular, attractors in the set of tourism variables. Analysis was
carried out based on a pre-designed algorithm and applying our
interpretation of chaos theory developed in the context of General
Systems Theory. This article sets out the causal relationships
associated with tourist flows in order to enable the formulation of
appropriate strategies. Our results can be applied to numerous cases.
For example, in the analysis of tourist flows, these findings can be
used to determine whether the behaviour of certain groups affects that
of other groups and to analyse tourist behaviour in terms of the most
relevant variables. Unlike statistical analyses that merely provide
information on current data, our method uses orbit analysis to
forecast, if attractors are found, the behaviour of tourist variables in
the immediate future.
Abstract: Fuel cell's system requires regulating circuit for
voltage and current in order to control power in case of connecting to
other generative devices or load. In this paper Fuel cell system and
convertor, which is a multi-variable system, are controlled using
sliding mode method. Use of weighting matrix in design procedure
made it possible to regulate speed of control. Simulation results show
the robustness and accuracy of proposed controller for controlling
desired of outputs.
Abstract: With the globalized production and logistics
environment, the need for reducing the product development interval
and lead time, having a faster response to orders, conforming to quality
standards, fair tracking, and boosting information exchanging
activities with customers and partners, and coping with changes in the
management environment, manufacturers are in dire need of an
information management system in their manufacturing environments.
There are lots of information systems that have been designed to
manage the condition or operation of equipment in the field but
existing systems have a decentralized architecture, which is not
unified. Also, these systems cannot effectively handle the status data
extraction process upon encountering a problem related to protocols or
changes in the equipment or the setting. In this regard, this paper will
introduce a system for processing and saving the status info of
production equipment, which uses standard representation formats, to
enable flexible responses to and support for variables in the field
equipment. This system can be used for a variety of manufacturing and
equipment settings and is capable of interacting with higher-tier
systems such as MES.
Abstract: Total liquid ventilation can support gas exchange in animal models of lung injury. Clinical application awaits further technical improvements and performance verification. Our aim was to develop a liquid ventilator, able to deliver accurate tidal volumes, and a computerized system for measuring lung mechanics. The computer-assisted, piston-driven respirator controlled ventilatory parameters that were displayed and modified on a real-time basis. Pressure and temperature transducers along with a lineal displacement controller provided the necessary signals to calculate lung mechanics. Ten newborn lambs (
Abstract: This paper addresses the problem of blind source separation
(BSS). To recover original signals, from linear instantaneous
mixtures, we propose a new contrast function based on the use of a
double referenced system. Our approach assumes statistical independence
sources. The reference vectors will be incrusted in the cumulant
to evaluate the independence. The estimation of the separating matrix
will be performed in two steps: whitening observations and joint
diagonalization of a set of referenced cumulant matrices. Computer
simulations are presented to demonstrate the effectiveness of the
suggested approach.
Abstract: For smaller mechatronic device, especially for micro
Electronic system, a micro machining is a must. However, most
investigations on vibration of a mill have been limited to the
traditional type mill. In this article, vibration and dynamic
characteristics of a micro mill were investigated in this study. The
trend towards higher precision manufacturing technology requires
producing miniaturized components. To improve micro-milled
product quality, obtain a higher production rate and avoid milling
breakage, the dynamic characteristics of micro milling must be
studied. A stepped pre-twisted mill is used to simulate the micro mill.
The finite element analysis is employed in this work. The flute length
and diameter effects of the micro mill are considered. It is clear that
the effects of micro mill shape parameters on vibration in a micro mill
are significant.
Abstract: This paper presents a web based remote access
microcontroller laboratory. Because of accelerated development in
electronics and computer technologies, microcontroller-based devices
and appliances are found in all aspects of our daily life. Before the
implementation of remote access microcontroller laboratory an
experiment set is developed by teaching staff for training
microcontrollers. Requirement of technical teaching and industrial
applications are considered when experiment set is designed.
Students can make the experiments by connecting to the experiment
set which is connected to the computer that set as the web server. The
students can program the microcontroller, can control digital and
analog inputs and can observe experiment. Laboratory experiment
web page can be accessed via www.elab.aku.edu.tr address.
Abstract: In this paper a unified approach via block-pulse functions (BPFs) or shifted Legendre polynomials (SLPs) is presented to solve the linear-quadratic-Gaussian (LQG) control problem. Also a recursive algorithm is proposed to solve the above problem via BPFs. By using the elegant operational properties of orthogonal functions (BPFs or SLPs) these computationally attractive algorithms are developed. To demonstrate the validity of the proposed approaches a numerical example is included.
Abstract: This paper presents an investigation into the design of a flight control system, using a robust sliding mode control structure, designed using the exact feedback linearization procedure of the dynamic of a small-size autonomous helicopter in hover. The robustness of the controller in the context of stabilization and trajectory tracking with respect to small body forces and air resistance on the main and tail rotor, is analytically proved using Lyapunov approach. Some simulation results are presented to illustrate the performance and robustness of such controller in the presence of small body forces and air resistance.
Abstract: Internet infrastructures in most places of the world
have been supported by the advancement of optical fiber technology,
most notably wavelength division multiplexing (WDM) system.
Optical technology by means of WDM system has revolutionized
long distance data transport and has resulted in high data capacity,
cost reductions, extremely low bit error rate, and operational
simplification of the overall Internet infrastructure. This paper
analyses and compares the system impairments, which occur at data
transmission rates of 2.5Gb/s and 10 Gb/s per wavelength channel in
our proposed optical WDM system for Internet infrastructure in
Tanzania. The results show that the data transmission rate of 2.5 Gb/s
has minimum system impairments compared with a rate of 10 Gb/s
per wavelength channel, and achieves a sufficient system
performance to provide a good Internet access service.
Abstract: Static Var Compensator (SVC) is a shunt type FACTS
device which is used in power system primarily for the purpose of
voltage and reactive power control. In this paper, a fuzzy logic based
supplementary controller for Static Var Compensator (SVC) is
developed which is used for damping the rotor angle oscillations and
to improve the transient stability of the power system. Generator
speed and the electrical power are chosen as input signals for the
Fuzzy Logic Controller (FLC). The effectiveness and feasibility of
the proposed control is demonstrated with Single Machine Infinite
Bus (SMIB) system and multimachine system (WSCC System)
which show improvement over the use of a fixed parameter
controller.
Abstract: This study examined the role of driving experience in hazard perception and categorization using traffic scene pictures. Specifically, young-inexperienced, moderately experienced and very experienced (taxi) drivers observed traffic scene pictures while connected to an eye tracking system and were asked to rate the level of hazardousness of each picture and to mention the three most prominent hazards in it. Target pictures included nine, nearly identical, pairs of pictures where one picture in each pair included an actual hazard as an additional element. Altogether, 22 areas of interest (AOIs) were predefined and included 13 potential hazards and 9 actual hazards. Data analysis included both verbal reports and eye scanning patterns of these AOIs. Generally, both experienced and taxi drivers noted a relatively larger number of potential hazards than young inexperienced drivers Thus, by relating to less salient potential hazards, experienced drivers have demonstrated a better situation model of the traffic environment.
Abstract: The sanitary sewerage connection rate becomes an
important indicator of advanced cities. Following the construction of
sanitary sewerages, the maintenance and management systems are
required for keeping pipelines and facilities functioning well. These
maintenance tasks often require sewer workers to enter the manholes
and the pipelines, which are confined spaces short of natural
ventilation and full of hazardous substances. Working in sewers could
be easily exposed to a risk of adverse health effects. This paper
proposes the use of Bayesian belief networks (BBN) as a higher level
of noncarcinogenic health risk assessment of sewer workers. On the
basis of the epidemiological studies, the actual hospital attendance
records and expert experiences, the BBN is capable of capturing the
probabilistic relationships between the hazardous substances in sewers
and their adverse health effects, and accordingly inferring the
morbidity and mortality of the adverse health effects. The provision of
the morbidity and mortality rates of the related diseases is more
informative and can alleviate the drawbacks of conventional methods.
Abstract: The security of power systems against malicious cyberphysical
data attacks becomes an important issue. The adversary
always attempts to manipulate the information structure of the power
system and inject malicious data to deviate state variables while
evading the existing detection techniques based on residual test. The
solutions proposed in the literature are capable of immunizing the
power system against false data injection but they might be too costly
and physically not practical in the expansive distribution network.
To this end, we define an algebraic condition for trustworthy power
system to evade malicious data injection. The proposed protection
scheme secures the power system by deterministically reconfiguring
the information structure and corresponding residual test. More
importantly, it does not require any physical effort in either microgrid
or network level. The identification scheme of finding meters being
attacked is proposed as well. Eventually, a well-known IEEE 30-bus
system is adopted to demonstrate the effectiveness of the proposed
schemes.
Abstract: The Artificial immune systems algorithms are Meta
heuristic optimization method, which are used for clustering and
pattern recognition applications are abundantly. These algorithms in
multimodal optimization problems are more efficient than genetic
algorithms. A major drawback in these algorithms is their slow
convergence to global optimum and their weak stability can be
considered in various running of these algorithms. In this paper,
improved Artificial Immune System Algorithm is introduced for the
first time to overcome its problems of artificial immune system. That
use of the small size of a local search around the memory antibodies
is used for improving the algorithm efficiently. The credibility of the
proposed approach is evaluated by simulations, and it is shown that
the proposed approach achieves better results can be achieved
compared to the standard artificial immune system algorithms
Abstract: Access to information is the key to the empowerment of everybody despite where they are living. This research is to be carried out in respect of the people living in developing countries, considering their plight and complex geographical, demographic, social-economic conditions surrounding the areas they live, which hinder access to information and of professionals providing services such as medical workers, which has led to high death rates and development stagnation. Research on Unified Communications and Integrated Collaborations (UCIC) system in the health sector of developing countries comes in to create a possible solution of bridging the digital canyon among the communities. The aim is to deliver services in a seamless manner to assist health workers situated anywhere to be accessed easily and access information which will help in service delivery. The proposed UCIC provides the most immersive Telepresence experience for one-to-one or many-tomany meetings. Extending to locations anywhere in the world, the transformative platform delivers Ultra-low operating costs through the use of general purpose networks and using special lenses and track systems.
Abstract: The paper discusses complexity of component-based
development (CBD) of embedded systems. Although CBD has its
merits, it must be augmented with methods to control the complexities
that arise due to resource constraints, timeliness, and run-time deployment
of components in embedded system development. Software
component specification, system-level testing, and run-time reliability
measurement are some ways to control the complexity.
Abstract: The request for a sustainable development challenges
both managers and consumers to rethink habitual practices and
activities. While consumers are challenged to develop sustainable
consumption patterns, companies are asked to establish managerial
systems and structures considering economical, ecological, and social
issues. As this is in particular true for housing associations, this paper
aims first, at providing an understanding of sustainability strategy in
residential trade and industry (RTI) by identifying relevant facets of
this construct and second, at conceptually analyzing the impact of
sustainability strategy in RTI on operational efficiency and
performance of municipal housing companies. The author develops a
model of sustainability strategy in RTI and its effects and further,
sheds light in priorities for future research.
Abstract: An additive fuzzy system comprising m rules with
n inputs and p outputs in each rule has at least t m(2n + 2 p + 1)
parameters needing to be tuned. The system consists of a large
number of if-then fuzzy rules and takes a long time to tune its
parameters especially in the case of a large amount of training data
samples. In this paper, a new learning strategy is investigated to cope
with this obstacle. Parameters that tend toward constant values at the
learning process are initially fixed and they are not tuned till the end
of the learning time. Experiments based on applications of the
additive fuzzy system in function approximation demonstrate that the
proposed approach reduces the learning time and hence improves
convergence speed considerably.