Abstract: To support mobility in ATM networks, a number of
technical challenges need to be resolved. The impact of handoff
schemes in terms of service disruption, handoff latency, cost
implications and excess resources required during handoffs needs to
be addressed. In this paper, a one phase handoff and route
optimization solution using reserved PVCs between adjacent ATM
switches to reroute connections during inter-switch handoff is
studied. In the second phase, a distributed optimization process is
initiated to optimally reroute handoff connections. The main
objective is to find the optimal operating point at which to perform
optimization subject to cost constraint with the purpose of reducing
blocking probability of inter-switch handoff calls for delay tolerant
traffic. We examine the relation between the required bandwidth
resources and optimization rate. Also we calculate and study the
handoff blocking probability due to lack of bandwidth for resources
reserved to facilitate the rapid rerouting.
Abstract: This work involved the use of phytoremediation to
remediate an aged soil contaminated with polychlorinated biphenyls
(PCBs). At microcosm scale, tests were prepared using soil samples
that have been collected in an industrial area with a total PCBs
concentration of about 250 μg kg-1. Medicago sativa and Lolium
italicum were the species selected in this study that is used as
“feasibility test" for full scale remediation. The experiment was
carried out with the addition of a mixture of randomly methylatedbeta-
cyclodextrins (RAMEB). At the end of the experiment analysis
of soil samples showed that in general the presence of plants has led
to a higher degradation of most congeners with respect to not
vegetated soil. The two plant species efficiencies were comparable
and improved by RAMEB addition with a final reduction of total
PCBs near to 50%. With increasing the chlorination of the congeners
the removal percentage of PCBs progressively decreased.
Abstract: This paper presents a new hardware interface using a
microcontroller which processes audio music signals to standard
MIDI data. A technique for processing music signals by extracting
note parameters from music signals is described. An algorithm to
convert the voice samples for real-time processing without complex
calculations is proposed. A high frequency microcontroller as the
main processor is deployed to execute the outlined algorithm. The
MIDI data generated is transmitted using the EIA-232 protocol. The
analyses of data generated show the feasibility of using
microcontrollers for real-time MIDI generation hardware interface.
Abstract: This article is devoted to the numerical solution of
large-scale quadratic eigenvalue problems. Such problems arise in
a wide variety of applications, such as the dynamic analysis of
structural mechanical systems, acoustic systems, fluid mechanics,
and signal processing. We first introduce a generalized second-order
Krylov subspace based on a pair of square matrices and two initial
vectors and present a generalized second-order Arnoldi process for
constructing an orthonormal basis of the generalized second-order
Krylov subspace. Then, by using the projection technique and the
refined projection technique, we propose a restarted generalized
second-order Arnoldi method and a restarted refined generalized
second-order Arnoldi method for computing some eigenpairs of largescale
quadratic eigenvalue problems. Some theoretical results are also
presented. Some numerical examples are presented to illustrate the
effectiveness of the proposed methods.
Abstract: By the application of an improved back-propagation
neural network (BPNN), a model of current densities for a solid oxide
fuel cell (SOFC) with 10 layers is established in this study. To build
the learning data of BPNN, Taguchi orthogonal array is applied to
arrange the conditions of operating parameters, which totally 7 factors
act as the inputs of BPNN. Also, the average current densities
achieved by numerical method acts as the outputs of BPNN.
Comparing with the direct solution, the learning errors for all learning
data are smaller than 0.117%, and the predicting errors for 27
forecasting cases are less than 0.231%. The results show that the
presented model effectively builds a mathematical algorithm to predict
performance of a SOFC stack immediately in real time.
Also, the calculating algorithms are applied to proceed with the
optimization of the average current density for a SOFC stack. The
operating performance window of a SOFC stack is found to be
between 41137.11 and 53907.89. Furthermore, an inverse predicting
model of operating parameters of a SOFC stack is developed here by
the calculating algorithms of the improved BPNN, which is proved to
effectively predict operating parameters to achieve a desired
performance output of a SOFC stack.
Abstract: The effects of coatings based on sodium alginate (S.A) and carboxyl methyl cellulose (CMC) on the color and moisture characteristics of potato round slices were investigated. It is the first time that this combination of polysaccharides is used as edible coating which alone had the best performance as inhibitor of potato color discoloration during the storage of 15 days at 4oC. When ascorbic acid (AA) and green tea (GT) were added in the above edible coating its effects on potato round slices changed. The mixtures of sodium alginate and carboxyl methyl cellulose with ascorbic acid or with green tea behave as a potential moisture barrier, resulting to the extent of potato samples self–life. These data suggests that both GT and AA are potential inhibitors of dehydration in potatoes and not only natural antioxidants.
Abstract: Task of object localization is one of the major
challenges in creating intelligent transportation. Unfortunately, in
densely built-up urban areas, localization based on GPS only
produces a large error, or simply becomes impossible. New
opportunities arise for the localization due to the rapidly emerging
concept of a wireless ad-hoc network. Such network, allows
estimating potential distance between these objects measuring
received signal level and construct a graph of distances in which
nodes are the localization objects, and edges - estimates of the
distances between pairs of nodes. Due to the known coordinates of
individual nodes (anchors), it is possible to determine the location of
all (or part) of the remaining nodes of the graph. Moreover, road
map, available in digital format can provide localization routines
with valuable additional information to narrow node location search.
However, despite abundance of well-known algorithms for solving
the problem of localization and significant research efforts, there are
still many issues that currently are addressed only partially. In this
paper, we propose localization approach based on the graph mapped
distances on the digital road map data basis. In fact, problem is
reduced to distance graph embedding into the graph representing area
geo location data. It makes possible to localize objects, in some cases
even if only one reference point is available. We propose simple
embedding algorithm and sample implementation as spatial queries
over sensor network data stored in spatial database, allowing
employing effectively spatial indexing, optimized spatial search
routines and geometry functions.
Abstract: Building Sector is the major electricity consumer and
it is costly to building owners. Therefore the application of thermal
energy storage (TES) has gained attractive to reduce energy cost.
Many attractive tariff packages are being offered by the electricity
provider to promote TES. The tariff packages offered higher cost of
electricity during peak period and lower cost of electricity during off
peak period. This paper presented the return of initial investment by
implementing a centralized air-conditioning plant integrated with
thermal energy storage with partially operation strategies. Building
load profile will be calculated hourly according to building
specification and building usage trend. TES operation conditions will
be designed according to building load demand profile, storage
capacity, tariff packages and peak/off peak period. The Payback
Period analysis method was used to evaluate economic analysis. The
investment is considered a good investment where by the initial cost
is recovered less than ten than seven years.
Abstract: This paper may be considered as combination of both pervasive computing and Differential GPS (global positioning satellite) which relates to control automatic traffic signals in such a
way as to pre-empt normal signal operation and permit lifesaving vehicles. Before knowing the arrival of the lifesaving vehicles from
the signal there is a chance of clearing the traffic. Traffic signal
preemption system includes a vehicle equipped with onboard computer system capable of capturing diagnostic information and
estimated location of the lifesaving vehicle using the information provided by GPS receiver connected to the onboard computer system
and transmitting the information-s using a wireless transmitter via a
wireless network. The fleet management system connected to a
wireless receiver is capable of receiving the information transmitted
by the lifesaving vehicle .A computer is also located at the
intersection uses corrected vehicle position, speed & direction
measurements, in conjunction with previously recorded data defining
approach routes to the intersection, to determine the optimum time to
switch a traffic light controller to preemption mode so that lifesaving
vehicles can pass safely. In case when the ambulance need to take a
“U" turn in a heavy traffic area we suggest a solution. Now we are
going to make use of computerized median which uses LINKED
BLOCKS (removable) to solve the above problem.
Abstract: In this study arsenate [As(V)] removal from drinking water by coagulation process was investigated. Ferric chloride (FeCl3.6H2O) and ferrous sulfate (FeSO4.7H2O) were used as coagulant. The effects of major operating variables such as coagulant dose (1–30 mg/L) and pH (5.5–9.5) were investigated. Ferric chloride and ferrous sulfate were found as effective and reliable coagulant due to required dose, residual arsenate and coagulant concentration. Optimum pH values for maximum arsenate removal for ferrous sulfate and ferric chloride were found as 8 and 7.5. The arsenate removal efficiency decreased at neutral and acidic pH values for Fe(II) and at the high acidic and high alkaline pH for Fe(III). It was found that the increase of coagulant dose caused a substantial increase in the arsenate removal. But above a certain ferric chloride and ferrous sulfate dosage, the increase in arsenate removal was not significant. Ferric chloride and ferrous sulfate dose above 8 mg/L slightly increased arsenate removal.
Abstract: The objective of this paper is to support the application of Open Innovation practices in firms and organizations by the assessment and management of Intellectual Capital. Intellectual Capital constituents are analyzed in order to verify their capability of acting as key drivers of Open Innovation processes and, therefore, of creating value. A methodology is defined to settle a procedure which helps to select the most relevant Intellectual Capital value drivers and to provide Communities of Innovation with strategic and managerial guidelines in sustaining Open Innovation paradigm. An application of the methodology is developed within a specifically addressed project and its results are hereafter examined.
Abstract: The effect of concentration of reduction agent of
sodium borohydrate (NaBH4) on the properties of silicon
nanoparticles synthesized via microemulsion route is reported. In
this work, the concentration of the silicon tetrachloride (SiCl4) that
served as silicon source with sodium hydroxide (NaOH) and
polyethylene glycol (PEG) as stabilizer and surfactant, respectively,
are keep fixed. Four samples with varied concentration of NaBH4
from 0.05 M to 0.20 M were synthesized. It was found that the lowest
concentration of NaBH4 gave better formation of silicon
nanoparticles.
Abstract: Despite the internet, which is one of the mass media
that has become quite common in recent years, the relationship of
Advertisement with Television and Cinema, which have always
drawn attention of researchers as basic media and where visual use is
in the foreground, have also become the subject of various studies.
Based on the assumption that the known fundamental effects of
advertisements on consumers are closely related to the creative
process of advertisements as well as the nature and characteristics of
the medium where they are used, these basic mass media (Television
and Cinema) and the consumer motivations of the advertisements
they broadcast have become a focus of study.
Given that the viewers of the mass media in question have shifted
from a passive position to a more active one especially in recent years
and approach contents of advertisements, as they do all contents, in a
more critical and “pitiless" manner, it is possible to say that
individuals make more use of advertisements than in the past and
combine their individual goals with the goals of the advertisements.
This study, which aims at finding out what the goals of these new
individual advertisement use are, how they are shaped by the distinct
characteristics of Television and Cinema, where visuality takes
precedence as basic mass media, and what kind of places they occupy
in the minds of consumers, has determined consumers- motivations
as: “Entertainment", “Escapism", “Play", “Monitoring/Discovery",
“Opposite Sex" and “Aspirations and Role Models".
This study intends to reveal the differences or similarities among
the needs and hence the gratifications of viewers who consume
advertisements on Television or at the Cinema, which are two basic
media where visuality is prioritized.
Abstract: In this article, by means of examination of Bolshevists
Turkistanskie Vedomosti" newspaper and “Erikti Oylar Organi" and
“Turkistanskyi Vestnik" newspapers which had been published
during 1917-1918, the fact that “Turkistan Governorship" established
in city of Kokand in November of 1917, within the framework of
former tsarist Russia Turkistan general-governorship, was the legal
government formed as a requisition of people of Turkistan was
proved. An examination of these two newspapers providing
information regarding history of “Turkistan Autonomy" but having
opposite to each other views makes it possible to obtain valuable data
concerning history of autonomy which was inappropriately
misrepresented during Soviet period.
Abstract: The present work is motivated by the idea that the
layer deformation in anisotropic elasticity can be estimated from the
theory of interfacial dislocations. In effect, this work which is an
extension of a previous approach given by one of the authors
determines the anisotropic displacement fields and the critical
thickness due to a complex biperiodic network of MDs lying just
below the free surface in view of the arrangement of dislocations.
The elastic fields of such arrangements observed along interfaces
play a crucial part in the improvement of the physical properties of
epitaxial systems. New results are proposed in anisotropic elasticity
for hexagonal networks of MDs which contain intrinsic and extrinsic
stacking faults. We developed, using a previous approach based on
the relative interfacial displacement and a Fourier series formulation
of the displacement fields, the expressions of elastic fields when
there is a possible dissociation of MDs. The numerical investigations
in the case of the observed system Si/(111)Si with low twist angles
show clearly the effect of the anisotropy and thickness when the
misfit networks are dissociated.
Abstract: Molecular dynamics simulation of annular flow
boiling in a nanochannel with 70000 particles is numerically
investigated. In this research, an annular flow model is developed to
predict the superheated flow boiling heat transfer characteristics in a
nanochannel. To characterize the forced annular boiling flow in a
nanochannel, an external driving force F ext ranging from 1to12PN
(PN= Pico Newton) is applied along the flow direction to inlet fluid
particles during the simulation. Based on an annular flow model
analysis, it is found that saturation condition and superheat degree
have great influences on the liquid-vapor interface. Also, the results
show that due to the relatively strong influence of surface tension in
small channel, the interface between the liquid film and vapor core is
fairly smooth, and the mean velocity along the stream-wise direction
does not change anymore.
Abstract: In this paper, a novel approach is presented
for designing multiplier-free state-space digital filters. The
multiplier-free design is obtained by finding power-of-2 coefficients
and also quantizing the state variables to power-of-2
numbers. Expressions for the noise variance are derived for the
quantized state vector and the output of the filter. A “structuretransformation
matrix" is incorporated in these expressions. It
is shown that quantization effects can be minimized by properly
designing the structure-transformation matrix. Simulation
results are very promising and illustrate the design algorithm.
Abstract: The current methods of predictive controllers are
utilized for those processes in which the rate of output variations is
not high. For such processes, therefore, stability can be achieved by
implementing the constrained predictive controller or applying
infinite prediction horizon. When the rate of the output growth is
high (e.g. for unstable nonminimum phase process) the stabilization
seems to be problematic. In order to avoid this, it is suggested to
change the method in the way that: first, the prediction error growth
should be decreased at the early stage of the prediction horizon, and
second, the rate of the error variation should be penalized. The
growth of the error is decreased through adjusting its weighting
coefficients in the cost function. Reduction in the error variation is
possible by adding the first order derivate of the error into the cost
function. By studying different examples it is shown that using these
two remedies together, the closed-loop stability of unstable
nonminimum phase process can be achieved.
Abstract: Automatic detection of syllable repetition is one of the
important parameter in assessing the stuttered speech objectively.
The existing method which uses artificial neural network (ANN)
requires high levels of agreement as prerequisite before attempting to
train and test ANNs to separate fluent and nonfluent. We propose
automatic detection method for syllable repetition in read speech for
objective assessment of stuttered disfluencies which uses a novel
approach and has four stages comprising of segmentation, feature
extraction, score matching and decision logic. Feature extraction is
implemented using well know Mel frequency Cepstra coefficient
(MFCC). Score matching is done using Dynamic Time Warping
(DTW) between the syllables. The Decision logic is implemented by
Perceptron based on the score given by score matching. Although
many methods are available for segmentation, in this paper it is done
manually. Here the assessment by human judges on the read speech
of 10 adults who stutter are described using corresponding method
and the result was 83%.
Abstract: The boundary layer flow and heat transfer on a
stretched surface moving with prescribed skin friction is studied for
permeable surface. The surface temperature is assumed to vary
inversely with the vertical direction x for n = -1. The skin friction at
the surface scales as (x-1/2) at m = 0. The constants m and n are the
indices of the power law velocity and temperature exponent
respectively. Similarity solutions are obtained for the boundary layer
equations subject to power law temperature and velocity variation.
The effect of various governing parameters, such as the buoyancy
parameter λ and the suction/injection parameter fw for air (Pr = 0.72)
are studied. The choice of n and m ensures that the used similarity
solutions are x independent. The results show that, assisting flow (λ >
0) enhancing the heat transfer coefficient along the surface for any
constant value of fw. Furthermore, injection increases the heat
transfer coefficient but suction reduces it at constant λ.