Abstract: The integral form of equations of motion of composite
beams subjected to varying time loads are discretized using a
developed finite element model. The model consists of a straight five
node twenty-two degrees of freedom beam element. The stability
analysis of the beams is studied by solving the matrix form
characteristic equations of the system. The principle of virtual work
and the first order shear deformation theory are employed to analyze
the beams with large deformation and small strains. The regions of
dynamic instability of the beam are determined by solving the
obtained Mathieu form of differential equations. The effects of nonconservative
loads, shear stiffness, and damping parameters on
stability and response of the beams are examined. Several numerical
calculations are presented to compare the results with data reported
by other researchers.
Abstract: Estimation of natural frequency of structures is very
important and isn-t usually calculated simply and sometimes
complicated. Lack of knowledge about that caused hard damage and
hazardous effects.
In this paper, with using from two different models in FEM
method and based on hydrodynamic mass of fluids, natural frequency
of an especial bearing (Fig. 1) in an electric field (or, a periodic
force) is calculated in different stiffness and different geometric. In
final, the results of two models and analytical solution are compared.
Abstract: A climate dependent model is proposed to simulate
the population of Aedes aegypti mosquito. In developing the model,
average temperature of Shah Alam, Malaysia was used to determine
the development rate of each stage of the life cycle of mosquito.
Rainfall dependent function was proposed to simulate the hatching
rate of the eggs under several assumptions. The proposed transition
matrix was obtained and used to simulate the population of eggs,
larvae, pupae and adults mosquito. It was found that the peak of
mosquito abundance comes during a relatively dry period following a
heavy rainfall. In addition, lag time between the peaks of mosquito
abundance and dengue fever cases in Shah Alam was estimated.
Abstract: In this investigation, anatase TiO2 thin films were
grown by radio frequency magnetron sputtering on glass substrates at
a high sputtering pressure and room temperature. The anatase films
were then annealed at 300-600 °C in air for a period of 1 hour. To
examine the structure and morphology of the films, X-ray diffraction
(XRD) and atomic force microscopy (AFM) methods were used
respectively. From X-ray diffraction patterns of the TiO2 films, it was
found that the as-deposited film showed some differences compared
with the annealed films and the intensities of the peaks of the
crystalline phase increased with the increase of annealing
temperature. From AFM images, the distinct variations in the
morphology of the thin films were also observed. The optical
constants were characterized using the transmission spectra of the
films obtained by UV-VIS-IR spectrophotometer. Besides, optical
thickness of the film deposited at room temperature was calculated
and cross-checked by taking a cross-sectional image through SEM.
The optical band gaps were evaluated through Tauc model. It was
observed that TiO2 films produced at room temperatures exhibited
high visible transmittance and transmittance decreased slightly with
the increase of annealing temperatures. The films were found to be
crystalline having anatase phase. The refractive index of the films
was found from 2.31-2.35 in the visible range. The extinction
coefficient was nearly zero in the visible range and was found to
increase with annealing temperature. The allowed indirect optical
band gap of the films was estimated to be in the range from 3.39 to
3.42 eV which showed a small variation. The allowed direct band
gap was found to increase from 3.67 to 3.72 eV. The porosity was
also found to decrease at a higher annealing temperature making the
film compact and dense.
Abstract: This experiment was conducted in attempt of
improving hydrodynamic efficiency of the propulsion mechanism by
installing a spring to the wing so that the opening angle of the wing in
one stroke can be changed automatically, compared to the existing
method of fixed maximum opening angle in Weis-Fogh type ship
propulsion mechanism. Average thrust coefficient was almost fixed
with all velocity ratio with the prototype, but with the spring type,
thrust coefficient increased sharply as velocity ratio increased.
Average propulsive efficiency was larger with bigger opening angle in
the prototype, but in the spring type, the one with smaller spring
coefficient had larger value. In the range over 1.0 in velocity ratio
where big thrust can be generated, spring type had more than twice of
propulsive efficiency increase compared to the prototype.
Abstract: Construction of portable device for fast analysis of energetic materials is described in this paper. The developed analytical system consists of two main parts: a miniaturized microcolumn liquid chromatograph of unique construction and original chemiluminescence detector. This novel portable device is able to determine selectively most of nitramine- and nitroester-based explosives as well as inorganic nitrates at trace concentrations in water or soil extracts in less than 8 minutes.
Abstract: The paper considers the effect of feed plate location
on the interactions in a seven plate binary distillation column. The
mathematical model of the distillation column is deduced based on
the equations of mass and energy balances for each stage, detailed
model for both reboiler and condenser, and heat transfer equations.
The Dynamic Relative Magnitude Criterion, DRMC is used to assess
the interactions in different feed plate locations for a seven plate
(Benzene-Toluene) binary distillation column ( the feed plate is
originally at stage 4). The results show that whenever we go far from
the optimum feed plate position, the level of interaction augments.
Abstract: Automatic control of the robotic manipulator involves
study of kinematics and dynamics as a major issue. This paper
involves the forward and inverse kinematics of 2-DOF robotic
manipulator with revolute joints. In this study the Denavit-
Hartenberg (D-H) model is used to model robot links and joints. Also
forward and inverse kinematics solution has been achieved using
Artificial Neural Networks for 2-DOF robotic manipulator. It shows
that by using artificial neural network the solution we get is faster,
acceptable and has zero error.
Abstract: Food borne illnesses have been reported to be a global
health challenge. Annual incidences of food–related diseases involve
76 million cases, of which only 14 million can be traced to known
pathogens. Poor hygienic practices have contributed greatly to this. It
has been reported that in the year 2000 about 2.1 million people died
from diarrheal diseases, hence, there is a need to ensure food safety at
all level. This study focused on the sterility examination and
inhibitory effect of honey samples on selected gram negative and
gram positive food borne pathogen from South West Nigeria. The
laboratory examinations revealed the presence of some bacterial and
fungal contaminations of honey samples and that inhibitory activity
of the honey sample was more pronounced on the gram negative
bacteria than the gram positive bacterial isolates. Antibiotic
sensitivity test conducted on the different bacterial isolates also
showed that honey was able to inhibit the proliferation of the tested
bacteria than the employed antibiotics.
Abstract: The use of amine mixtures employing
methyldiethanolamine (MDEA), monoethanolamine (MEA), and diethanolamine (DEA) have been investigated for a variety of cases
using a process simulation program called HYSYS. The results show that, at high pressures, amine mixtures have little or no advantage in the cases studied. As the pressure is lowered, it becomes more difficult for MDEA to meet residual gas requirements and mixtures can usually improve plant performance. Since the CO2 reaction rate
with the primary and secondary amines is much faster than with
MDEA, the addition of small amounts of primary or secondary amines to an MDEA based solution should greatly improve the overall reaction rate of CO2 with the amine solution. The addition of MEA caused the CO2 to be absorbed more strongly in the upper portion of the column than for MDEA along. On the other hand,
raising the concentration for MEA to 11%wt, CO2 is almost
completely absorbed in the lower portion of the column. The addition of MEA would be most advantageous.
Thus, in areas where MDEA cannot meet the residual gas
requirements, the use of amine mixtures can usually improve the plant
performance.
Abstract: This paper examined the influence of matching
students- learning preferences with the teaching methodology
adopted, on their academic performance in an accounting course in
two types of learning environment in one university in Lebanon:
classes with PowerPoint (PPT) vs. conventional classes. Learning
preferences were either for PPT or for Conventional methodology. A
statistically significant increase in academic achievement is found in
the conventionally instructed group as compared to the group taught
with PPT. This low effectiveness of PPT might be attributed to the
learning preferences of Lebanese students. In the PPT group, better
academic performance was found among students with
learning/teaching match as compared with students with
learning/teaching mismatch. Since the majority of students display a
preference for the conventional methodology, the result might
suggest that Lebanese students- performance is not optimized by PPT
in the accounting classrooms, not because of PPT itself, but because
it is not matching the Lebanese students- learning preferences in such
a quantitative course.
Abstract: In this paper an algorithm is used to detect the color defects of ceramic tiles. First the image of a normal tile is clustered using GCMA; Genetic C-means Clustering Algorithm; those results in best cluster centers. C-means is a common clustering algorithm which optimizes an objective function, based on a measure between data points and the cluster centers in the data space. Here the objective function describes the mean square error. After finding the best centers, each pixel of the image is assigned to the cluster with closest cluster center. Then, the maximum errors of clusters are computed. For each cluster, max error is the maximum distance between its center and all the pixels which belong to it. After computing errors all the pixels of defected tile image are clustered based on the centers obtained from normal tile image in previous stage. Pixels which their distance from their cluster center is more than the maximum error of that cluster are considered as defected pixels.
Abstract: Background: Widespread use of chemotherapeutic
drugs in the treatment of cancer has lead to higher health hazards
among employee who handle and administer such drugs, so nurses
should know how to protect themselves, their patients and their work
environment against toxic effects of chemotherapy. Aim of this study
was carried out to examine the effect of chemotherapy safety protocol
for oncology nurses on their protective measure practices. Design: A
quasi experimental research design was utilized. Setting: The study
was carried out in oncology department of Menoufia university
hospital and Tanta oncology treatment center. Sample: A
convenience sample of forty five nurses in Tanta oncology treatment
center and eighteen nurses in Menoufiya oncology department.
Tools: 1. an interviewing questionnaire that covering sociodemographic
data, assessment of unit and nurses' knowledge about
chemotherapy. II: Obeservational check list to assess nurses' actual
practices of handling and adminestration of chemotherapy. A base
line data were assessed before implementing Chemotherapy Safety
protocol, then Chemotherapy Safety protocol was implemented, and
after 2 monthes they were assessed again. Results: reveled that 88.9%
of study group I and 55.6% of study group II improved to good total
knowledge scores after educating on the safety protocol, also 95.6%
of study group I and 88.9% of study group II had good total practice
score after educating on the safety protocol. Moreover less than half
of group I (44.4%) reported that heavy workload is the most barriers
for them, while the majority of group II (94.4%) had many barriers
for adhering to the safety protocol such as they didn’t know the
protocol, the heavy work load and inadequate equipment.
Conclusions: Safety protocol for Oncology Nurses seemed to have
positive effect on improving nurses' knowledge and practice.
Recommendation: chemotherapy safety protocol should be instituted
for all oncology nurses who are working in any oncology unit and/ or
center to enhance compliance, and this protocol should be done at
frequent intervals.
Abstract: The role of entrepreneurs in generating the economy is
very important. Thus, nurturing entrepreneurship skills among
society is very crucial and should start from the early age. One of the
methods is to teach through game such as board game. Game
provides a fun and interactive platform for players to learn and play.
Besides that as today-s world is moving towards Islamic approach in
terms of finance, banking and entertainment but Islamic based game
is still hard to find in the market especially games on
entrepreneurship. Therefore, there is a gap in this segment that can be
filled by learning entrepreneurship through game. The objective of
this paper is to develop an entrepreneurship digital-based game
entitled “Catur Bistari" that is based on Islamic business approach.
Knowledge and skill of entrepreneurship and Islamic business
approach will be learned through the tasks that are incorporated
inside the game.
Abstract: Palladium-catalyzed hydrodechlorination is a
promising alternative for the treatment of environmentally relevant
water bodies, such as groundwater, contaminated with chlorinated
organic compounds (COCs). In the aqueous phase
hydrodechlorination of COCs, Pd-based catalysts were found to have
a very high catalytic activity. However, the full utilization of the
catalyst-s potential is impeded by the sensitivity of the catalyst to
poisoning and deactivation induced by reduced sulfur compounds
(e.g. sulfides). Several regenerants have been tested before to recover
the performance of sulfide-fouled Pd catalyst. But these only
delivered partial success with respect to re-establishment of the
catalyst activity. In this study, the deactivation behaviour of
Pd/Al2O3 in the presence of sulfide was investigated. Subsequent to
total deactivation the catalyst was regenerated in the aqueous phase
using potassium permanganate. Under neutral pH condition,
oxidative regeneration with permanganate delivered a slow recovery
of catalyst activity. However, changing the pH of the bulk solution to
acidic resulted in the complete recovery of catalyst activity within a
regeneration time of about half an hour. These findings suggest the
superiority of permanganate as regenerant in re-activating Pd/Al2O3
by oxidizing Pd-bound sulfide.
Abstract: Importance of software quality is increasing leading to development of new sophisticated techniques, which can be used in constructing models for predicting quality attributes. One such technique is Artificial Neural Network (ANN). This paper examined the application of ANN for software quality prediction using Object- Oriented (OO) metrics. Quality estimation includes estimating maintainability of software. The dependent variable in our study was maintenance effort. The independent variables were principal components of eight OO metrics. The results showed that the Mean Absolute Relative Error (MARE) was 0.265 of ANN model. Thus we found that ANN method was useful in constructing software quality model.
Abstract: Independent component analysis (ICA) in the
frequency domain is used for solving the problem of blind source
separation (BSS). However, this method has some problems. For
example, a general ICA algorithm cannot determine the permutation
of signals which is important in the frequency domain ICA. In this
paper, we propose an approach to the solution for a permutation
problem. The idea is to effectively combine two conventional
approaches. This approach improves the signal separation
performance by exploiting features of the conventional approaches.
We show the simulation results using artificial data.
Abstract: In this study, an ablation, mechanical and thermal properties of a rocket motor insulation from phenolic/ fiber matrix composites forming a laminate with different fiber between fiberglass and locally available synthetic fibers. The phenolic/ fiber matrix composites was mechanics and thermal properties by means of tensile strength, ablation, TGA and DSC. The design of thermal insulation involves several factors.Determined the mechanical properties according to MIL-I-24768: Density >1.3 g/cm3, Tensile strength >103 MPa and Ablation
Abstract: The paradigm of mobile agent provides a promising technology for the development of distributed and open applications. However, one of the main obstacles to widespread adoption of the mobile agent paradigm seems to be security. This paper treats the security of the mobile agent against malicious host attacks. It describes generic mobile agent protection architecture. The proposed approach is based on the dynamic adaptability and adopts the reflexivity as a model of conception and implantation. In order to protect it against behaviour analysis attempts, the suggested approach supplies the mobile agent with a flexibility faculty allowing it to present an unexpected behaviour. Furthermore, some classical protective mechanisms are used to reinforce the level of security.
Abstract: In this paper, to optimize the “Characteristic Straight Line Method" which is used in the soil displacement analysis, a “best estimate" of the geodetic leveling observations has been achieved by taking in account the concept of 'Height systems'. This concept has been discussed in detail and consequently the concept of “height". In landslides dynamic analysis, the soil is considered as a mosaic of rigid blocks. The soil displacement has been monitored and analyzed by using the “Characteristic Straight Line Method". Its characteristic components have been defined constructed from a “best estimate" of the topometric observations. In the measurement of elevation differences, we have used the most modern leveling equipment available. Observational procedures have also been designed to provide the most effective method to acquire data. In addition systematic errors which cannot be sufficiently controlled by instrumentation or observational techniques are minimized by applying appropriate corrections to the observed data: the level collimation correction minimizes the error caused by nonhorizontality of the leveling instrument's line of sight for unequal sight lengths, the refraction correction is modeled to minimize the refraction error caused by temperature (density) variation of air strata, the rod temperature correction accounts for variation in the length of the leveling rod' s Invar/LO-VAR® strip which results from temperature changes, the rod scale correction ensures a uniform scale which conforms to the international length standard and the introduction of the concept of the 'Height systems' where all types of height (orthometric, dynamic, normal, gravity correction, and equipotential surface) have been investigated. The “Characteristic Straight Line Method" is slightly more convenient than the “Characteristic Circle Method". It permits to evaluate a displacement of very small magnitude even when the displacement is of an infinitesimal quantity. The inclination of the landslide is given by the inverse of the distance reference point O to the “Characteristic Straight Line". Its direction is given by the bearing of the normal directed from point O to the Characteristic Straight Line (Fig..6). A “best estimate" of the topometric observations was used to measure the elevation of points carefully selected, before and after the deformation. Gross errors have been eliminated by statistical analyses and by comparing the heights within local neighborhoods. The results of a test using an area where very interesting land surface deformation occurs are reported. Monitoring with different options and qualitative comparison of results based on a sufficient number of check points are presented.