Abstract: In the urban traffic network, the intersections are the
“bottleneck point" of road network capacity. And the arterials are the
main body in road network and the key factor which guarantees the
normal operation of the city-s social and economic activities. The
rapid increase in vehicles leads to seriously traffic jam and cause the
increment of vehicles- delay. Most cities of our country are
traditional single control system, which cannot meet the need for the
city traffic any longer. In this paper, Synchro6.0 as a platform to
minimize the intersection delay, optimizesingle signal cycle and split
for Zhonghua Street in Handan City. Meanwhile, linear control
system uses to optimize the phase for the t arterial road in this
system. Comparing before and after use the control, capacities and
service levels of this road and the adjacent road have improved
significantly.
Abstract: The mineral having chemical compositional formula MgAl2O4 is called “spinel". The ferrites crystallize in spinel structure are known as spinel-ferrites or ferro-spinels. The spinel structure has a fcc cage of oxygen ions and the metallic cations are distributed among tetrahedral (A) and octahedral (B) interstitial voids (sites). The X-ray diffraction (XRD) intensity of each Bragg plane is sensitive to the distribution of cations in the interstitial voids of the spinel lattice. This leads to the method of determination of distribution of cations in the spinel oxides through XRD intensity analysis. The computer program for XRD intensity analysis has been developed in C language and also tested for the real experimental situation by synthesizing the spinel ferrite materials Mg0.6Zn0.4AlxFe2- xO4 and characterized them by X-ray diffractometry. The compositions of Mg0.6Zn0.4AlxFe2-xO4(x = 0.0 to 0.6) ferrites have been prepared by ceramic method and powder X-ray diffraction patterns were recorded. Thus, the authenticity of the program is checked by comparing the theoretically calculated data using computer simulation with the experimental ones. Further, the deduced cation distributions were used to fit the magnetization data using Localized canting of spins approach to explain the “recovery" of collinear spin structure due to Al3+ - substitution in Mg-Zn ferrites which is the case if A-site magnetic dilution and non-collinear spin structure. Since the distribution of cations in the spinel ferrites plays a very important role with regard to their electrical and magnetic properties, it is essential to determine the cation distribution in spinel lattice.
Abstract: This paper proposes a prototype of a lower-limb
rehabilitation system for recovering and strengthening patients-
injured lower limbs. The system is composed of traction motors for
each leg position, a treadmill as a walking base, tension sensors,
microcontrollers controlling motor functions and a main system with
graphic user interface. For derivation of reference or normal velocity
profiles of the body segment point, kinematic method is applied based
on the humanoid robot model using the reference joint angle data of
normal walking.
Abstract: How to coordinate the behaviors of the agents through
learning is a challenging problem within multi-agent domains.
Because of its complexity, recent work has focused on how
coordinated strategies can be learned. Here we are interested in using
reinforcement learning techniques to learn the coordinated actions of a
group of agents, without requiring explicit communication among
them. However, traditional reinforcement learning methods are based
on the assumption that the environment can be modeled as Markov
Decision Process, which usually cannot be satisfied when multiple
agents coexist in the same environment. Moreover, to effectively
coordinate each agent-s behavior so as to achieve the goal, it-s
necessary to augment the state of each agent with the information
about other existing agents. Whereas, as the number of agents in a
multiagent environment increases, the state space of each agent grows
exponentially, which will cause the combinational explosion problem.
Profit sharing is one of the reinforcement learning methods that allow
agents to learn effective behaviors from their experiences even within
non-Markovian environments. In this paper, to remedy the drawback
of the original profit sharing approach that needs much memory to
store each state-action pair during the learning process, we firstly
address a kind of on-line rational profit sharing algorithm. Then, we
integrate the advantages of modular learning architecture with on-line
rational profit sharing algorithm, and propose a new modular
reinforcement learning model. The effectiveness of the technique is
demonstrated using the pursuit problem.
Abstract: In this paper we considered the Neumann problem for
the fourth order differential equation. First we define the weighted Sobolev space
2 Wα and generalized solution for this equation. Then we consider the existence and uniqueness of the generalized solution,
as well as give the description of the spectrum and of the domain of definition of the corresponding operator.
Abstract: The prediction of financial time series is a very
complicated process. If the efficient market hypothesis holds, then the predictability of most financial time series would be a rather
controversial issue, due to the fact that the current price contains already all available information in the market. This paper extends
the Adaptive Neuro Fuzzy Inference System for High Frequency
Trading which is an expert system that is capable of using fuzzy reasoning combined with the pattern recognition capability of neural networks to be used in financial forecasting and trading in high
frequency. However, in order to eliminate unnecessary input in the
training phase a new event based volatility model was proposed.
Taking volatility and the scaling laws of financial time series into consideration has brought about the development of the Intraday Seasonality Observation Model. This new model allows the observation of specific events and seasonalities in data and subsequently removes any unnecessary data. This new event based
volatility model provides the ANFIS system with more accurate input
and has increased the overall performance of the system.
Abstract: Since the 1980s, banks and financial service institutions have been running in an endless race of innovation to cope with the advancing technology, the fierce competition, and the more sophisticated and demanding customers. In order to guide their innovation efforts, several researches were conducted to identify the success and failure factors of new financial services. These mainly included organizational factors, marketplace factors and new service development process factors. They almost all emphasized the importance of customer and market orientation as a response to the highly perceptual and intangible characteristics of financial services. However, they deemphasized the critical characteristics of high involvement of risk and close correlation with the economic conditions, a factor that heavily contributed to the Global financial Crisis of 2008. This paper reviews the success and failure factors of new financial services. It then adds new perspectives emerging from the analysis of the role of innovation in the global financial crisis.
Abstract: Analysis of the elastic scattering of protons on 6,7Li
nuclei has been done in the framework of the optical model at the
beam energies up to 50 MeV. Differential cross sections for the 6,7Li +
p scattering were measured over the proton laboratory–energy range
from 400 to 1050 keV. The elastic scattering of 6,7Li+p data at
different proton incident energies have been analyzed using singlefolding
model. In each case the real potential obtained from the
folding model was supplemented by a phenomenological imaginary
potential, and during the fitting process the real potential was
normalized and the imaginary potential optimized. Normalization
factor NR is calculated in the range between 0.70 and 0.84.
Abstract: Gene expression profiling is rapidly evolving into a
powerful technique for investigating tumor malignancies. The
researchers are overwhelmed with the microarray-based platforms
and methods that confer them the freedom to conduct large-scale
gene expression profiling measurements. Simultaneously,
investigations into cross-platform integration methods have started
gaining momentum due to their underlying potential to help
comprehend a myriad of broad biological issues in tumor diagnosis,
prognosis, and therapy. However, comparing results from different
platforms remains to be a challenging task as various inherent
technical differences exist between the microarray platforms. In this
paper, we explain a simple ratio-transformation method, which can
provide some common ground for cDNA and Affymetrix platform
towards cross-platform integration. The method is based on the
characteristic data attributes of Affymetrix- and cDNA- platform. In
the work, we considered seven childhood leukemia patients and their
gene expression levels in either platform. With a dataset of 822
differentially expressed genes from both these platforms, we carried
out a specific ratio-treatment to Affymetrix data, which subsequently
showed an improvement in the relationship with the cDNA data.
Abstract: Efficient preprocessing is very essential for automatic
recognition of handwritten documents. In this paper, techniques on
segmenting words in handwritten Arabic text are presented. Firstly,
connected components (ccs) are extracted, and distances among
different components are analyzed. The statistical distribution of this
distance is then obtained to determine an optimal threshold for words
segmentation. Meanwhile, an improved projection based method is
also employed for baseline detection. The proposed method has been
successfully tested on IFN/ENIT database consisting of 26459
Arabic words handwritten by 411 different writers, and the results
were promising and very encouraging in more accurate detection of
the baseline and segmentation of words for further recognition.
Abstract: It is well known that a linear dynamic system including
a delay will exhibit limit cycle oscillations when a bang-bang sensor
is used in the feedback loop of a PID controller. A similar behaviour
occurs when a delayed feedback signal is used to train a neural
network. This paper develops a method of predicting this behaviour
by linearizing the system, which can be shown to behave in a manner
similar to an integral controller. Using this procedure, it is possible
to predict the characteristics of the neural network driven limit cycle
to varying degrees of accuracy, depending on the information known
about the system. An application is also presented: the intelligent
control of a spark ignition engine.
Abstract: This article attempts to analyze functionally graded beam thermal buckling along with piezoelectric layers applying based on the third order shearing deformation theory considering various boundary conditions. The beam properties are assumed to vary continuously from the lower surface to the upper surface of the beam. The equilibrium equations are derived using the total potential energy equations, Euler equations, piezoelectric material constitutive equations and third order shear deformation theory assumptions. In order to fulfill such an aim, at first functionally graded beam with piezoelectric layers applying the third order shearing deformation theory along with clamped -clamped boundary conditions are thoroughly analyzed, and then following making sure of the correctness of all the equations, the very same beam is analyzed with piezoelectric layers through simply-simply and simply-clamped boundary conditions. In this article buckling critical temperature for functionally graded beam is derived in two different ways, without piezoelectric layer and with piezoelectric layer and the results are compared together. Finally, all the conclusions obtained will be compared and contrasted with the same samples in the same and distinguished conditions through tables and charts. It would be noteworthy that in this article, the software MAPLE has been applied in order to do the numeral calculations.
Abstract: As an economic and safe structure, Bi-steel is widely
used in reinforced concrete with less consumption of steel. In this
paper, III Bi-steel concrete beam has been analyzed. Through careful
observation and theoretical analysis, the new calculating formulae for
structural rigidity and crack have been formulated for this Bi-steel
concrete beam. And structural rigidity and the crack features have also
been theoretically analyzed.
Abstract: Wastages such as grated coconut meat, spent tea and used sugarcane had contributed negative impacts to the environment. Vermicomposting method is fully utilized to manage the wastes towards a more sustainable approach. The worms that are used in the vermicomposting are Eisenia foetida and Eudrillus euginae. This research shows that the vermicompost of wastages has voltage of electrical energy and is able to light up the Light-Emitting Diode (LED) device. Based on the experiment, the use of replicated and double compartments of the component will produce double of voltage. Hence, for conclusion, this harmless and low cost technology of vermicompost can act as a dry cell in order to reduce the usage of hazardous chemicals that can contaminate the environment.
Abstract: A numerical method for Riccati equation is presented in this work. The method is based on the replacement of unknown functions through a truncated series of hybrid of block-pulse functions and Chebyshev polynomials. The operational matrices of derivative and product of hybrid functions are presented. These matrices together with the tau method are then utilized to transform the differential equation into a system of algebraic equations. Corresponding numerical examples are presented to demonstrate the accuracy of the proposed method.
Abstract: The permanent magnet synchronous motor (PMSM) is
very useful in many applications. Vector control of PMSM is popular
kind of its control. In this paper, at first an optimal vector control for
PMSM is designed and then results are compared with conventional
vector control. Then, it is assumed that the measurements are noisy
and linear quadratic Gaussian (LQG) methodology is used to filter
the noises. The results of noisy optimal vector control and filtered
optimal vector control are compared to each other. Nonlinearity of
PMSM and existence of inverter in its control circuit caused that the
system is nonlinear and time-variant. With deriving average model,
the system is changed to nonlinear time-invariant and then the
nonlinear system is converted to linear system by linearization of
model around average values. This model is used to optimize vector
control then two optimal vector controls are compared to each other.
Simulation results show that the performance and robustness to noise
of the control system has been highly improved.
Abstract: This paper presents a method to support dynamic
packing in cases when no collision-free path can be found. The
method, which is primarily based on path planning and shrinking of
geometries, suggests a minimal geometry design change that results
in a collision-free assembly path. A supplementing approach to
optimize geometry design change with respect to redesign cost is
described. Supporting this dynamic packing method, a new method
to shrink geometry based on vertex translation, interweaved with
retriangulation, is suggested. The shrinking method requires neither
tetrahedralization nor calculation of medial axis and it preserves the
topology of the geometry, i.e. holes are neither lost nor introduced.
The proposed methods are successfully applied on industrial
geometries.
Abstract: While compressing text files is useful, compressing
still image files is almost a necessity. A typical image takes up much
more storage than a typical text message and without compression
images would be extremely clumsy to store and distribute. The
amount of information required to store pictures on modern
computers is quite large in relation to the amount of bandwidth
commonly available to transmit them over the Internet and
applications. Image compression addresses the problem of reducing
the amount of data required to represent a digital image. Performance
of any image compression method can be evaluated by measuring the
root-mean-square-error & peak signal to noise ratio. The method of
image compression that will be analyzed in this paper is based on the
lossy JPEG image compression technique, the most popular
compression technique for color images. JPEG compression is able to
greatly reduce file size with minimal image degradation by throwing
away the least “important" information. In JPEG, both color
components are downsampled simultaneously, but in this paper we
will compare the results when the compression is done by
downsampling the single chroma part. In this paper we will
demonstrate more compression ratio is achieved when the
chrominance blue is downsampled as compared to downsampling the
chrominance red in JPEG compression. But the peak signal to noise
ratio is more when the chrominance red is downsampled as compared
to downsampling the chrominance blue in JPEG compression. In
particular we will use the hats.jpg as a demonstration of JPEG
compression using low pass filter and demonstrate that the image is
compressed with barely any visual differences with both methods.
Abstract: Demand of energy is increasing faster than the
generation. It leads shortage of power in all sectors of society. At
peak hours this shortage is higher. Unless we utilize energy efficient
technology, it is very difficult to minimize the shortage of energy. So
energy efficiency program and energy conservation has an important
role. Energy efficient technologies are cost intensive hence it is
always not possible to implement in country like India. In the recent
study, an educational building with operating hours from 10:00 a.m.
to 05:00 p.m. has been selected to quantify the possibility of lighting
energy conservation. As the operating hour is in daytime, integration
of daylight with artificial lighting system will definitely reduce the
lighting energy consumption. Moreover the initial investment has
been given priority and hence the existing lighting installation was
unaltered. An automatic controller has been designed which will be
operated as a function of daylight through windows and the lighting
system of the room will function accordingly. The result of the study
of integrating daylight gave quite satisfactory for visual comfort as
well as energy conservation.
Abstract: This paper presents Genetic Algorithm (GA) based
approach for the allocation of FACTS (Flexible AC Transmission
System) devices for the improvement of Power transfer capacity in an
interconnected Power System. The GA based approach is applied on
IEEE 30 BUS System. The system is reactively loaded starting from
base to 200% of base load. FACTS devices are installed in the
different locations of the power system and system performance is
noticed with and without FACTS devices. First, the locations, where
the FACTS devices to be placed is determined by calculating active
and reactive power flows in the lines. Genetic Algorithm is then
applied to find the amount of magnitudes of the FACTS devices. This
approach of GA based placement of FACTS devices is tremendous
beneficial both in terms of performance and economy is clearly
observed from the result obtained.