Abstract: In this paper, propose method that can user’s position
that based on database is built from single camera. Previous
positioning calculate distance by arrival-time of signal like GPS
(Global Positioning System), RF(Radio Frequency). However, these
previous method have weakness because these have large error range
according to signal interference. Method for solution estimate position
by camera sensor. But, signal camera is difficult to obtain relative
position data and stereo camera is difficult to provide real-time
position data because of a lot of image data, too. First of all, in this
research we build image database at space that able to provide
positioning service with single camera. Next, we judge similarity
through image matching of database image and transmission image
from user. Finally, we decide position of user through position of most
similar database image. For verification of propose method, we
experiment at real-environment like indoor and outdoor. Propose
method is wide positioning range and this method can verify not only
position of user but also direction.
Abstract: Location selection presents a crucial decision problem in today’s business world where strategic decision making processes have critical importance. Thus, location selection has strategic importance for companies in boosting their strength regarding competition, increasing corporate performances and efficiency in addition to lowering production and transportation costs. A right choice in location selection has a direct impact on companies’ commercial success. In this study, a store location selection problem of Carglass Turkey which operates in vehicle glass branch is handled. As this problem includes both tangible and intangible criteria, Analytic Network Process (ANP) was accepted as the main methodology. The model consists of control hierarchy and BOCR subnetworks which include clusters of actors, alternatives and criteria. In accordance with the management’s choices, five different locations were selected. In addition to the literature review, a strict cooperation with the actor group was ensured and maintained while determining the criteria and during whole process. Obtained results were presented to the management as a report and its feasibility was confirmed accordingly.
Abstract: The material behavior of graphene, a single layer of
carbon lattice, is extremely sensitive to its dielectric environment. We
demonstrate improvement in electronic performance of graphene
nanowire interconnects with full encapsulation by lattice-matching,
chemically inert, 2D layered insulator hexagonal boron nitride (h-
BN). A novel layer-based transfer technique is developed to construct
the h-BN/MLG/h-BN heterostructures. The encapsulated graphene
wires are characterized and compared with that on SiO2 or h-BN
substrate without passivating h-BN layer. Significant improvements
in maximum current-carrying density, breakdown threshold, and
power density in encapsulated graphene wires are observed. These
critical improvements are achieved without compromising the carrier
transport characteristics in graphene. Furthermore, graphene wires
exhibit electrical behavior less insensitive to ambient conditions, as
compared with the non-passivated ones. Overall, h-BN/graphene/h-
BN heterostructure presents a robust material platform towards the
implementation of high-speed carbon-based interconnects.
Abstract: As greenhouse effect has been recognized as serious environmental problem of the world, interests in carbon dioxide (CO2) emission which comprises major part of greenhouse gas (GHG) emissions have been increased recently. Since construction industry takes a relatively large portion of total CO2 emissions of the world, extensive studies about reducing CO2 emissions in construction and operation of building have been carried out after the 2000s. Also, performance based design (PBD) methodology based on nonlinear analysis has been robustly developed after Northridge Earthquake in 1994 to assure and assess seismic performance of building more exactly because structural engineers recognized that prescriptive code based design approach cannot address inelastic earthquake responses directly and assure performance of building exactly. Although CO2 emissions and PBD approach are recent rising issues on construction industry and structural engineering, there were few or no researches considering these two issues simultaneously. Thus, the objective of this study is to minimize the CO2 emissions and cost of building designed by PBD approach in structural design stage considering structural materials. 4 story and 4 span reinforced concrete building optimally designed to minimize CO2 emissions and cost of building and to satisfy specific seismic performance (collapse prevention in maximum considered earthquake) of building satisfying prescriptive code regulations using non-dominated sorting genetic algorithm-II (NSGA-II). Optimized design result showed that minimized CO2 emissions and cost of building were acquired satisfying specific seismic performance. Therefore, the methodology proposed in this paper can be used to reduce both CO2 emissions and cost of building designed by PBD approach.
Abstract: Cytotoxic platinum compounds play a major role in the chemotherapy of a large number of human cancers. However, due to the severe side effects for the patient and other problems associated with their use, there is a need for the development of more efficient drugs and new methods for their selective delivery to the tumours. One way to achieve the latter could be in the use of nanoparticular substrates that can adsorb or chemically bind the drug. In the cell, the drug is supposed to be slowly released, either by physical desorption or by dissolution of the particle framework. Ideally, the cytotoxic properties of the platinum drug unfold only then, in the cancer cell and over a longer period of time due to the gradual release. In this paper, we report on our first steps in this direction. The binding properties of a series of cytotoxic Pt(II) oxadiazoline compounds to mesoporous silica particles has been studied by NMR and UV/vis spectroscopy. High loadings were achieved when the Pt(II) compound was relatively polar, and has been dissolved in a relatively nonpolar solvent before the silica was added. Typically, 6-10 hours were required for complete equilibration, suggesting the adsorption did not only occur to the outer surface but also to the interior of the pores. The untreated and Pt(II) loaded particles were characterised by C, H, N combustion analysis, BET/BJH nitrogen sorption, electron microscopy (REM and TEM) and EDX. With the latter methods we were able to demonstrate the homogenous distribution of the Pt(II) compound on and in the silica particles, and no Pt(II) bulk precipitate had formed. The in vitro cytotoxicity in a human cancer cell line (HeLa) has been determined for one of the new platinum compounds adsorbed to mesoporous silica particles of different size, and compared with the corresponding compound in solution. The IC50 data are similar in all cases, suggesting that the release of the Pt(II) compound was relatively fast and possibly occurred before the particles reached the cells. Overall, the platinum drug is chemically stable on silica and retained its activity upon prolonged storage.
Abstract: Coffee is a widely consumed beverage with many components such as caffeine, flavonoids, phenolic compounds, and minerals. Coffee consumption continues to increase due to its physiological effects, its pleasant taste, and aroma. Robusta and Arabica are two basic types of coffee beans. The coffee bean used for Turkish coffee is Arabica. There are many elements in the structure of coffee and have various effect on human health such as Sodium (Na), Boron (B), Magnesium (Mg) and Iron (Fe). In this study, the amounts of Mg, Na, Fe, and B contents in Turkish coffee are determined and effect of sugar addition is investigated for conscious consumption. The analysis of the contents of coffees was determined by using inductively coupled plasma optical emission spectrometry (ICP-OES). From the results of the experiments the Mg, Na, Fe and B contents of Turkish coffee after sugar addition were found as 19.83, 1.04, 0.02, 0.21 ppm, while without using sugar these concentrations were found 21.46, 0.81, 0.008 and 0.16 ppm. In addition, element contents were calculated for 1, 3 and 5 cups of coffee in order to investigate the health effects.
Abstract: This study has an objective to analyze foreign policy
of member states in globalization current, aiming to answer that the
foreign policy of member states have been changed or remained the
same and there are any factors affecting changing of foreign policy of
the member states.
From the study results, it is found that the foreign policy of
Thailand is a friendly foreign policy with all states. The policy of
Indonesia is more opened because of a change in leader, allowing
more democratic development in the country; the government has
proceeded with friendly foreign policy with the states in order to
bring funds into the state. The foreign policy of Malaysia is not much
changed as there is no changing in the leader; the policy of Malaysia
has reconciled relations with main city of Indian and Chinese residing
in the country in order to bring investments into the country and to
relieve tensions in the country. The foreign policy of the Philippines
has proceeded with policy under the ASEAN framework and
emphasized on international Islam communities. The foreign policy
of Singapore has the least changed as the Singapore's policy focuses
on internal trade since the state was found. As for the foreign policy
of Brunei Darussalam, Brunei has a little role in the international
stage; the state having closest relationship as from the view of history
is Singapore as the Singaporean has invested in retailing business in
Brunei. The foreign policy of Vietnam has emphasized on an
omnidirectional foreign policy in order to compete with several states
in global stage. The foreign policy of Myanmar has proceeded with a
friendly foreign policy with all ASEAN member states, the East-west
Corridor transportation line from Myanmar through Thailand and Lao
to Vietnam has been developed. As for the foreign policy of Lao, In
2001, the Thai government and Lao government held a discussion
which Thailand reaffirmed the position not to support the anti-Lao
group. The foreign policy of Cambodia has proceeded with more
openness, having good relation with China, Russia and USA as these
states has invested in the state, especially the US company.
Abstract: From a theoretical perspective, electric buses can be more sustainable and can be cheaper than fossil fuelled buses in city traffic. The authors have not found other studies based on actual urban public transport in Swedish winter climate. Further on, noise measurements from buses for the European market were found old. The aims of this follow-up study was therefore to test and possibly verify in a real-life environment how energy efficient and silent electric buses are, and then conclude on if electric buses are preferable to use in public transport. The Ebusco 2.0 electric bus, fitted with a 311 kWh battery pack, was used and the tests were carried out during November 2014-April 2015 in eight municipalities in the south of Sweden. Six tests took place in urban traffic and two took place in more of a rural traffic setting. The energy use for propulsion was measured via logging of the internal system in the bus and via an external charging meter. The average energy use turned out to be 8% less (0,96 kWh/km) than assumed in the earlier theoretical study. This rate allows for a 320 km range in public urban traffic. The interior of the bus was kept warm by a diesel heater (biodiesel will probably be used in a future operational traffic situation), which used 0,67 kWh/km in January. This verified that electric buses can be up to 25% cheaper when used in public transport in cities for about eight years. The noise was found to be lower, primarily during acceleration, than for buses with combustion engines in urban bus traffic. According to our surveys, most passengers and drivers appreciated the silent and comfortable ride and preferred electric buses rather than combustion engine buses. Bus operators and passenger transport executives were also positive to start using electric buses for public transport. The operators did however point out that procurement processes need to account for eventual risks regarding this new technology, along with personnel education. The study revealed that it is possible to establish a charging infrastructure for almost all studied bus lines. However, design of a charging infrastructure for each municipality requires further investigations, including electric grid capacity analysis, smart location of charging points, and tailored schedules to allow fast charging. In conclusion, electric buses proved to be a preferable alternative for all stakeholders involved in public bus transport in the studied municipalities. However, in order to electric buses to be a prominent support for sustainable development, they need to be charged either by stand-alone units or via an expansion of the electric grid, and the electricity should be made from new renewable sources.
Abstract: Transient simulation of the hydrogen-assisted self-ignition of propane-air mixtures were carried out in platinum-coated micro-channels from ambient cold-start conditions, using a two-dimensional model with reduced-order reaction schemes, heat conduction in the solid walls, convection and surface radiation heat transfer. The self-ignition behavior of hydrogen-propane mixed fuel is analyzed and compared with the heated feed case. Simulations indicate that hydrogen can successfully cause self-ignition of propane-air mixtures in catalytic micro-channels with a 0.2 mm gap size, eliminating the need for startup devices. The minimum hydrogen composition for propane self-ignition is found to be in the range of 0.8-2.8% (on a molar basis), and increases with increasing wall thermal conductivity, and decreasing inlet velocity or propane composition. Higher propane-air ratio results in earlier ignition. The ignition characteristics of hydrogen-assisted propane qualitatively resemble the selectively inlet feed preheating mode. Transient response of the mixed hydrogen- propane fuel reveals sequential ignition of propane followed by hydrogen. Front-end propane ignition is observed in all cases. Low wall thermal conductivities cause earlier ignition of the mixed hydrogen-propane fuel, subsequently resulting in low exit temperatures. The transient-state behavior of this micro-scale system is described, and the startup time and minimization of hydrogen usage are discussed.
Abstract: This paper presents a subband adaptive filter (SAF)
for a system identification where an impulse response is sparse
and disturbed with an impulsive noise. Benefiting from the uses
of l1-norm optimization and l0-norm penalty of the weight vector
in the cost function, the proposed l0-norm sign SAF (l0-SSAF)
achieves both robustness against impulsive noise and much improved
convergence behavior than the classical adaptive filters. Simulation
results in the system identification scenario confirm that the proposed
l0-norm SSAF is not only more robust but also faster and more
accurate than its counterparts in the sparse system identification in
the presence of impulsive noise.
Abstract: We propose two affine projection algorithms (APA)
with variable regularization parameter. The proposed algorithms
dynamically update the regularization parameter that is fixed in the
conventional regularized APA (R-APA) using a gradient descent
based approach. By introducing the normalized gradient, the proposed
algorithms give birth to an efficient and a robust update scheme for
the regularization parameter. Through experiments we demonstrate
that the proposed algorithms outperform conventional R-APA in
terms of the convergence rate and the misadjustment error.
Abstract: We present a normalized LMS (NLMS) algorithm
with robust regularization. Unlike conventional NLMS with the
fixed regularization parameter, the proposed approach dynamically
updates the regularization parameter. By exploiting a gradient
descent direction, we derive a computationally efficient and robust
update scheme for the regularization parameter. In simulation, we
demonstrate the proposed algorithm outperforms conventional NLMS
algorithms in terms of convergence rate and misadjustment error.
Abstract: Many governments recently started to change the ways of providing their services by allowing their citizens to access services from anywhere without the need of visiting the location of the service provider. Mobile government (M-government) is one of the techniques that fulfill that goal. It has been adopted by many governments. M-government can be defined as an implementation of Electronic Government (E-Government) by using mobile technology with the aim of improving service delivery to citizens, businesses and all government agencies. There have been several research projects developing models to understand the behavior of individuals towards the adoption of m-government. This paper proposes a model for adoption of m-government services in Saudi Arabia by extending Technology Acceptance Model (TAM) by introducing external factors. This paper also reports on the development of a survey instrument designed to measure user perception of mobile government acceptance. A survey instrument has been developed by using existing scales from prior instruments and a pilot study has been conducted by distributing the survey to 33 participants. As a result, a survey instrument has been refined to retain 43 items. The results also showed that the reliabilities of all the scales in the survey instrument are above the levels acceptable in current academic research, thus the instruments developed by us are capable of analyzing the factors in M-government adoption.
Abstract: This paper presents a digital non-linear pulse-width modulation (PWM) controller in a high-voltage (HV) buck-boost DC-DC converter for the piezoelectric transducer of the down-hole acoustic telemetry system. The proposed design controls the generation of output signal with voltage higher than the supply voltage and is targeted to work under high temperature. To minimize the power consumption and silicon area, a simple and efficient design scheme is employed to develop the PWM controller. The proposed PWM controller consists of serial to parallel (S2P) converter, data assign block, a mode and duty cycle controller (MDC), linearly PWM (LPWM) and noise shaper, pulse generator and clock generator. To improve the reliability of circuit operation at higher temperature, this design is fabricated with the 1.0-μm silicon-on-insulator (SOI) CMOS process. The implementation results validated that the proposed design has the advantages of smaller size, lower power consumption and robust thermal stability.
Abstract: This paper explores the effectiveness of approaches used for the implementation of technology within central governments specifically Geographic Information Systems (GIS). It examines the extent to which various strategies to GIS implementation and its roll out to users within an organization is crucial for its long term assimilation. Depending on the contextual requirements, various implementation strategies exist spanning from the most revolutionary to the most evolutionary, which have an influence on the success of GIS projects and the realization of resulting business benefits within the central governments. This research compares between two strategies of GIS implementation within the Lebanese Municipalities. The first strategy is the “Technological Approach” which is focused on technology acquisition, overlaid on existing governmental frameworks. This approach gives minimal attention to capability building and the long term sustainability of the implemented program. The second strategy, referred to as the “Ecological Approach”, is naturally oriented to the function of the organization. This approach stresses on fostering the evolution of the program and on building the human capabilities. The Union of the Joumeh Municipalities will be presented as a case study under the “Ecological Approach” and the role of the GIS Center at the University of Balamand will be highlighted. Thus, this research contributes to the development of knowledge on technology implementation and the vital role of academia in the specific context of the Lebanese public sector so that this experience may pave the way for further applications.
Abstract: Up to this point business process management projects
in general and business process modelling projects in particular
could not rely on a practical and scientifically validated method to
estimate cost and effort. Especially the model development phase
is not covered by a cost estimation method or model. Further
phases of business process modelling starting with implementation
are covered by initial solutions which are discussed in the literature.
This article proposes a method of filling this gap by deriving a cost
estimation method from available methods in similar domains namely
software development or software engineering. Software development
is regarded as closely similar to process modelling as we show. After
the proposition of this method different ideas for further analysis and
validation of the method are proposed. We derive this method from
COCOMO II and Function Point which are established methods of
effort estimation in the domain of software development. For this
we lay out similarities of the software development process and the
process of process modelling which is a phase of the Business Process
Management life-cycle.
Abstract: Automatic program generation saves time, human resources, and allows receiving syntactically clear and logically correct modules. The 4-th generation programming languages are related to drawing the data and the processes of the subject area, as well as, to obtain a frame of the respective information system. The application can be separated in interface and business logic. That means, for an interactive generation of the needed system to be used an already existing toolkit or to be created a new one.
Abstract: This paper presents the findings of successful implementation of Business Process Reengineering (BPR) of cement dispatch activities in a cement manufacturing plant located in India. Simulation model was developed for the purpose of identifying and analyzing the areas for improvement. The company was facing a problem of low throughput rate and subsequent forced stoppages of the plant leading to a high production loss of 15000MT per month. It was found from the study that the present systems and procedures related to the in-plant logistics plant required significant changes. The major recommendations included process improvement at the entry gate, reducing the cycle time at the security gate and installation of an additional weigh bridge. This paper demonstrates how BPR can be implemented for improving the in-plant logistics process. Various recommendations helped the plant to increase its throughput by 14%.
Abstract: The recent tendency of ”Internet of Things” (IoT) has
developed in the last years, causing the emergence of innovative
communication methods among multiple devices. The appearance of
Bluetooth Low Energy (BLE) has allowed a push to IoT in relation
to smartphones. In this moment, a set of new applications related to
several topics like entertainment and advertisement has begun to be
developed but not much has been done till now to take advantage
of the potential that these technologies can offer on many business
areas and in everyday tasks. In the present work, the application of
BLE technology and smartphones is proposed on some business areas
related to the optimization of resource allocation in huge facilities
like airports. An indoor location system has been developed through
triangulation methods with the use of BLE beacons. The described
system can be used to locate all employees inside the building
in such a way that any task can be automatically assigned to a
group of employees. It should be noted that this system cannot
only be used to link needs with employees according to distances,
but it also takes into account other factors like occupation level or
category. In addition, it has been endowed with a security system
to manage business and personnel sensitive data. The efficiency of
communications is another essential characteristic that has been taken
into account in this work.
Abstract: The aim of this study was to improve the durability and quality of Bali beef (M. Longissimus dorsi) and broiler carcass through the addition of liquid smoke as a natural preservative. This study was using Longissimus dorsi muscle from male Bali beef aged 3 years, broiler breast and thigh aged 40 days. Three types of meat were marinated in liquid smoke with concentrations of 0, 5, and 10% for 30 minutes at the level of 20% of the sample weight (w/w). The samples were storage at 2-5°C for 1 month. This study designed as a factorial experiment 3 x 3 x 4 based on a completely randomized design with 5 replications; the first factor was meat type (beef, chicken breast and chicken thigh); the 2nd factor was liquid smoke concentrations (0, 5, and 10%), and the 3rd factor was storage duration (1, 2, 3, and 4 weeks). Parameters measured were TBA value, total bacterial colonies, water holding capacity (WHC), shear force value both before and after cooking (80°C – 15min.), and cooking loss. The results showed that the type of meat produced WHC, shear force value, cooking loss and TBA differed between the three types of meat. Higher concentration of liquid smoke, the WHC, shear force value, TBA, and total bacterial colonies were decreased; at a concentration of 10% of liquid smoke, the total bacterial colonies decreased by 57.3% from untreated with liquid smoke. Longer storage, the total bacterial colonies and WHC were increased, while the shear force value and cooking loss were decreased. It can be concluded that a 10% concentration of liquid smoke was able to maintain fat oxidation and bacterial growth in Bali beef and chicken breast and thigh.